| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Mon, 29 Nov 2021 19:17:56 +0100
From: Greg Kroah-Hartman <gregkh@...uxfoundation.org>
To: linux-kernel@...r.kernel.org
Cc: Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
stable@...r.kernel.org, Tomasz Maciej Nowak <tmn505@...il.com>,
Pali Rohár <pali@...nel.org>,
Marek Behún <marek.behun@....cz>,
Lorenzo Pieralisi <lorenzo.pieralisi@....com>,
Rob Herring <robh@...nel.org>,
Thomas Petazzoni <thomas.petazzoni@...tlin.com>,
Marek Behún <kabel@...nel.org>
Subject: [PATCH 5.4 27/92] PCI: aardvark: Improve link training
From: Marek Behún <marek.behun@....cz>
commit 43fc679ced18006b12d918d7a8a4af392b7fbfe7 upstream.
Currently the aardvark driver trains link in PCIe gen2 mode. This may
cause some buggy gen1 cards (such as Compex WLE900VX) to be unstable or
even not detected. Moreover when ASPM code tries to retrain link second
time, these cards may stop responding and link goes down. If gen1 is
used this does not happen.
Unconditionally forcing gen1 is not a good solution since it may have
performance impact on gen2 cards.
To overcome this, read 'max-link-speed' property (as defined in PCI
device tree bindings) and use this as max gen mode. Then iteratively try
link training at this mode or lower until successful. After successful
link training choose final controller gen based on Negotiated Link Speed
from Link Status register, which should match card speed.
Link: https://lore.kernel.org/r/20200430080625.26070-5-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@...il.com>
Signed-off-by: Pali Rohár <pali@...nel.org>
Signed-off-by: Marek Behún <marek.behun@....cz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@....com>
Reviewed-by: Rob Herring <robh@...nel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@...tlin.com>
Signed-off-by: Marek Behún <kabel@...nel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@...uxfoundation.org>
---
drivers/pci/controller/pci-aardvark.c | 114 ++++++++++++++++++++++++++--------
1 file changed, 89 insertions(+), 25 deletions(-)
--- a/drivers/pci/controller/pci-aardvark.c
+++ b/drivers/pci/controller/pci-aardvark.c
@@ -39,6 +39,7 @@
#define PCIE_CORE_LINK_CTRL_STAT_REG 0xd0
#define PCIE_CORE_LINK_L0S_ENTRY BIT(0)
#define PCIE_CORE_LINK_TRAINING BIT(5)
+#define PCIE_CORE_LINK_SPEED_SHIFT 16
#define PCIE_CORE_LINK_WIDTH_SHIFT 20
#define PCIE_CORE_ERR_CAPCTL_REG 0x118
#define PCIE_CORE_ERR_CAPCTL_ECRC_CHK_TX BIT(5)
@@ -249,6 +250,7 @@ struct advk_pcie {
struct mutex msi_used_lock;
u16 msi_msg;
int root_bus_nr;
+ int link_gen;
struct pci_bridge_emul bridge;
};
@@ -309,20 +311,16 @@ static inline bool advk_pcie_link_traini
static int advk_pcie_wait_for_link(struct advk_pcie *pcie)
{
- struct device *dev = &pcie->pdev->dev;
int retries;
/* check if the link is up or not */
for (retries = 0; retries < LINK_WAIT_MAX_RETRIES; retries++) {
- if (advk_pcie_link_up(pcie)) {
- dev_info(dev, "link up\n");
+ if (advk_pcie_link_up(pcie))
return 0;
- }
usleep_range(LINK_WAIT_USLEEP_MIN, LINK_WAIT_USLEEP_MAX);
}
- dev_err(dev, "link never came up\n");
return -ETIMEDOUT;
}
@@ -337,6 +335,85 @@ static void advk_pcie_wait_for_retrain(s
}
}
+static int advk_pcie_train_at_gen(struct advk_pcie *pcie, int gen)
+{
+ int ret, neg_gen;
+ u32 reg;
+
+ /* Setup link speed */
+ reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
+ reg &= ~PCIE_GEN_SEL_MSK;
+ if (gen == 3)
+ reg |= SPEED_GEN_3;
+ else if (gen == 2)
+ reg |= SPEED_GEN_2;
+ else
+ reg |= SPEED_GEN_1;
+ advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
+
+ /*
+ * Enable link training. This is not needed in every call to this
+ * function, just once suffices, but it does not break anything either.
+ */
+ reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
+ reg |= LINK_TRAINING_EN;
+ advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
+
+ /*
+ * Start link training immediately after enabling it.
+ * This solves problems for some buggy cards.
+ */
+ reg = advk_readl(pcie, PCIE_CORE_LINK_CTRL_STAT_REG);
+ reg |= PCIE_CORE_LINK_TRAINING;
+ advk_writel(pcie, reg, PCIE_CORE_LINK_CTRL_STAT_REG);
+
+ ret = advk_pcie_wait_for_link(pcie);
+ if (ret)
+ return ret;
+
+ reg = advk_readl(pcie, PCIE_CORE_LINK_CTRL_STAT_REG);
+ neg_gen = (reg >> PCIE_CORE_LINK_SPEED_SHIFT) & 0xf;
+
+ return neg_gen;
+}
+
+static void advk_pcie_train_link(struct advk_pcie *pcie)
+{
+ struct device *dev = &pcie->pdev->dev;
+ int neg_gen = -1, gen;
+
+ /*
+ * Try link training at link gen specified by device tree property
+ * 'max-link-speed'. If this fails, iteratively train at lower gen.
+ */
+ for (gen = pcie->link_gen; gen > 0; --gen) {
+ neg_gen = advk_pcie_train_at_gen(pcie, gen);
+ if (neg_gen > 0)
+ break;
+ }
+
+ if (neg_gen < 0)
+ goto err;
+
+ /*
+ * After successful training if negotiated gen is lower than requested,
+ * train again on negotiated gen. This solves some stability issues for
+ * some buggy gen1 cards.
+ */
+ if (neg_gen < gen) {
+ gen = neg_gen;
+ neg_gen = advk_pcie_train_at_gen(pcie, gen);
+ }
+
+ if (neg_gen == gen) {
+ dev_info(dev, "link up at gen %i\n", gen);
+ return;
+ }
+
+err:
+ dev_err(dev, "link never came up\n");
+}
+
static void advk_pcie_setup_hw(struct advk_pcie *pcie)
{
u32 reg;
@@ -382,12 +459,6 @@ static void advk_pcie_setup_hw(struct ad
PCIE_CORE_CTRL2_TD_ENABLE;
advk_writel(pcie, reg, PCIE_CORE_CTRL2_REG);
- /* Set GEN2 */
- reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
- reg &= ~PCIE_GEN_SEL_MSK;
- reg |= SPEED_GEN_2;
- advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
-
/* Set lane X1 */
reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
reg &= ~LANE_CNT_MSK;
@@ -435,20 +506,7 @@ static void advk_pcie_setup_hw(struct ad
*/
msleep(PCI_PM_D3COLD_WAIT);
- /* Enable link training */
- reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
- reg |= LINK_TRAINING_EN;
- advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
-
- /*
- * Start link training immediately after enabling it.
- * This solves problems for some buggy cards.
- */
- reg = advk_readl(pcie, PCIE_CORE_LINK_CTRL_STAT_REG);
- reg |= PCIE_CORE_LINK_TRAINING;
- advk_writel(pcie, reg, PCIE_CORE_LINK_CTRL_STAT_REG);
-
- advk_pcie_wait_for_link(pcie);
+ advk_pcie_train_link(pcie);
reg = advk_readl(pcie, PCIE_CORE_CMD_STATUS_REG);
reg |= PCIE_CORE_CMD_MEM_ACCESS_EN |
@@ -1278,6 +1336,12 @@ static int advk_pcie_probe(struct platfo
return ret;
}
+ ret = of_pci_get_max_link_speed(dev->of_node);
+ if (ret <= 0 || ret > 3)
+ pcie->link_gen = 3;
+ else
+ pcie->link_gen = ret;
+
advk_pcie_setup_hw(pcie);
ret = advk_sw_pci_bridge_init(pcie);
Powered by blists - more mailing lists