| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20211207094923.422422-1-howard.chiu@quantatw.com>
Date: Tue, 7 Dec 2021 17:49:24 +0800
From: Howard Chiu <howard10703049@...il.com>
To: robh+dt@...nel.org, joel@....id.au, andrew@...id.au,
devicetree@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
linux-aspeed@...ts.ozlabs.org, linux-kernel@...r.kernel.org,
patrick@...cx.xyz, Potin.Lai@...ntatw.com
Cc: Howard Chiu <howard.chiu@...ntatw.com>
Subject: [PATCH v8] ARM: dts: aspeed: Adding Facebook Bletchley BMC
Initial introduction of Facebook Bletchley equipped with
Aspeed 2600 BMC SoC.
Signed-off-by: Howard Chiu <howard.chiu@...ntatw.com>
---
Change since v7:
- Add switchphy mode back due to unknown failure
Change since v6:
- Fix FUSB302 node warnings
- Remove switchphy node.
- Remvoe status property from spi-gpio node
- Remove interrupt pin of FUSB302 temporally due to hardware issue
- Add more gpio-line-name
- Replace MP5023 device drivr with "mps,mp5023"
Change since v5:
- Add an EEPROM on i2c-7
- Change address of FUSB302 to 0x22
- Assign interrupt pin to FUSB302
- Rework pin assignment of pca9539
Change since v4:
- Change address of TMP421 on i2c-12 to 0x4d
Change since v3:
- Add a TMP421 on i2c-10
Change since v2:
- Remove uart5 workaround
- Remove gpio nodes of pca9552/pca9539
- Modify gpio-line-name of led/power/presence pins with openbmc pattern
- Add MP5023 devices
Change since v1:
- Keep sorted in Makefile
- Change baudrate to 57600 from 115200
- Rename node *-ember to *-amber
- Use openbmc-flash-layout-128.dtsi
arch/arm/boot/dts/Makefile | 1 +
.../dts/aspeed-bmc-facebook-bletchley.dts | 756 ++++++++++++++++++
2 files changed, 757 insertions(+)
create mode 100644 arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 0de64f237cd8..b804b577010a 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1482,6 +1482,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-bmc-arm-stardragon4800-rep2.dtb \
aspeed-bmc-asrock-e3c246d4i.dtb \
aspeed-bmc-bytedance-g220a.dtb \
+ aspeed-bmc-facebook-bletchley.dtb \
aspeed-bmc-facebook-cloudripper.dtb \
aspeed-bmc-facebook-cmm.dtb \
aspeed-bmc-facebook-elbert.dtb \
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
new file mode 100644
index 000000000000..f973ea883b97
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
@@ -0,0 +1,756 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2021 Facebook Inc.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/usb/pd.h>
+
+/ {
+ model = "Facebook Bletchley BMC";
+ compatible = "facebook,bletchley-bmc", "aspeed,ast2600";
+
+ aliases {
+ serial4 = &uart5;
+ };
+
+ chosen {
+ bootargs = "console=ttyS4,57600n8";
+ };
+
+ memory@...00000 {
+ device_type = "memory";
+ reg = <0x80000000 0x80000000>;
+ };
+
+ iio-hwmon {
+ compatible = "iio-hwmon";
+ io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+ <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+ <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
+ <&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
+ };
+
+ spi_gpio: spi-gpio {
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-sck = <&gpio0 ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
+ gpio-mosi = <&gpio0 ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
+ gpio-miso = <&gpio0 ASPEED_GPIO(Z, 5) GPIO_ACTIVE_HIGH>;
+ num-chipselects = <1>;
+ cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
+
+ tpmdev@0 {
+ compatible = "tcg,tpm_tis-spi";
+ spi-max-frequency = <33000000>;
+ reg = <0>;
+ };
+ };
+
+ switchphy: ethernet-phy@0 {
+ // Fixed link
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ sys_log_id {
+ retain-state-shutdown;
+ default-state = "keep";
+ gpios = <&front_leds 0 GPIO_ACTIVE_HIGH>;
+ };
+ fan0_blue {
+ retain-state-shutdown;
+ default-state = "on";
+ gpios = <&fan_ioexp 8 GPIO_ACTIVE_HIGH>;
+ };
+ fan1_blue {
+ retain-state-shutdown;
+ default-state = "on";
+ gpios = <&fan_ioexp 9 GPIO_ACTIVE_HIGH>;
+ };
+ fan2_blue {
+ retain-state-shutdown;
+ default-state = "on";
+ gpios = <&fan_ioexp 10 GPIO_ACTIVE_HIGH>;
+ };
+ fan3_blue {
+ retain-state-shutdown;
+ default-state = "on";
+ gpios = <&fan_ioexp 11 GPIO_ACTIVE_HIGH>;
+ };
+ fan0_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&fan_ioexp 12 GPIO_ACTIVE_HIGH>;
+ };
+ fan1_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&fan_ioexp 13 GPIO_ACTIVE_HIGH>;
+ };
+ fan2_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&fan_ioexp 14 GPIO_ACTIVE_HIGH>;
+ };
+ fan3_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&fan_ioexp 15 GPIO_ACTIVE_HIGH>;
+ };
+ sled0_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled0_leds 0 GPIO_ACTIVE_LOW>;
+ };
+ sled0_blue {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled0_leds 1 GPIO_ACTIVE_LOW>;
+ };
+ sled1_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled1_leds 0 GPIO_ACTIVE_LOW>;
+ };
+ sled1_blue {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled1_leds 1 GPIO_ACTIVE_LOW>;
+ };
+ sled2_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled2_leds 0 GPIO_ACTIVE_LOW>;
+ };
+ sled2_blue {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled2_leds 1 GPIO_ACTIVE_LOW>;
+ };
+ sled3_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled3_leds 0 GPIO_ACTIVE_LOW>;
+ };
+ sled3_blue {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled3_leds 1 GPIO_ACTIVE_LOW>;
+ };
+ sled4_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled4_leds 0 GPIO_ACTIVE_LOW>;
+ };
+ sled4_blue {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled4_leds 1 GPIO_ACTIVE_LOW>;
+ };
+ sled5_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled5_leds 0 GPIO_ACTIVE_LOW>;
+ };
+ sled5_blue {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled5_leds 1 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&mac2 {
+ status = "okay";
+ phy-mode = "rgmii";
+ phy-handle = <&switchphy>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rgmii3_default>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&rtc {
+ status = "okay";
+};
+
+&fmc {
+ status = "okay";
+ flash@0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "bmc";
+ spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+ };
+};
+
+&spi2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi2_default>;
+
+ flash@0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "pnor";
+ spi-max-frequency = <100000000>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+ /* TODO: Add ADC INA230 */
+
+ mp5023@40 {
+ compatible = "mps,mp5023";
+ reg = <0x40>;
+ };
+
+ tmp421@4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
+
+ sled0_ioexp: pca9539@76 {
+ compatible = "nxp,pca9539";
+ reg = <0x76>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "SLED0_MS_DETECT1","SLED0_VBUS_BMC_EN","SLED0_INA230_ALERT","SLED0_P12V_STBY_ALERT",
+ "SLED0_SSD_ALERT","SLED0_MS_DETECT0","SLED0_RST_CCG5","SLED0_FUSB302_INT",
+ "SLED0_MD_STBY_RESET","SLED0_MD_IOEXP_EN_FAULT","SLED0_MD_DIR","SLED0_MD_DECAY",
+ "SLED0_MD_MODE1","SLED0_MD_MODE2","SLED0_MD_MODE3","power-host0";
+ };
+
+ sled0_leds: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "led-sled0-amber","led-sled0-blue","SLED0_RST_IOEXP","",
+ "","","","",
+ "","","","",
+ "","","","";
+ };
+
+ sled0_fusb302: typec-portc@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ try-power-role = "sink";
+ data-role = "dual";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_VAR(3000, 12000, 3000)
+ PDO_PPS_APDO(3000, 11000, 3000)>;
+ op-sink-microwatt = <10000000>;
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ /* TODO: Add ADC INA230 */
+
+ mp5023@40 {
+ compatible = "mps,mp5023";
+ reg = <0x40>;
+ };
+
+ tmp421@4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
+
+ sled1_ioexp: pca9539@76 {
+ compatible = "nxp,pca9539";
+ reg = <0x76>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "SLED1_MS_DETECT1","SLED1_VBUS_BMC_EN","SLED1_INA230_ALERT","SLED1_P12V_STBY_ALERT",
+ "SLED1_SSD_ALERT","SLED1_MS_DETECT0","SLED1_RST_CCG5","SLED1_FUSB302_INT",
+ "SLED1_MD_STBY_RESET","SLED1_MD_IOEXP_EN_FAULT","SLED1_MD_DIR","SLED1_MD_DECAY",
+ "SLED1_MD_MODE1","SLED1_MD_MODE2","SLED1_MD_MODE3","power-host1";
+ };
+
+ sled1_leds: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "led-sled1-amber","led-sled1-blue","SLED1_RST_IOEXP","",
+ "","","","",
+ "","","","",
+ "","","","";
+ };
+
+ sled1_fusb302: typec-portc@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ try-power-role = "sink";
+ data-role = "dual";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_VAR(3000, 12000, 3000)
+ PDO_PPS_APDO(3000, 11000, 3000)>;
+ op-sink-microwatt = <10000000>;
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&i2c2 {
+ status = "okay";
+ /* TODO: Add ADC INA230 */
+
+ mp5023@40 {
+ compatible = "mps,mp5023";
+ reg = <0x40>;
+ };
+
+ tmp421@4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
+
+ sled2_ioexp: pca9539@76 {
+ compatible = "nxp,pca9539";
+ reg = <0x76>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "SLED2_MS_DETECT1","SLED2_VBUS_BMC_EN","SLED2_INA230_ALERT","SLED2_P12V_STBY_ALERT",
+ "SLED2_SSD_ALERT","SLED2_MS_DETECT0","SLED2_RST_CCG5","SLED2_FUSB302_INT",
+ "SLED2_MD_STBY_RESET","SLED2_MD_IOEXP_EN_FAULT","SLED2_MD_DIR","SLED2_MD_DECAY",
+ "SLED2_MD_MODE1","SLED2_MD_MODE2","SLED2_MD_MODE3","power-host2";
+ };
+
+ sled2_leds: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "led-sled2-amber","led-sled2-blue","SLED2_RST_IOEXP","",
+ "","","","",
+ "","","","",
+ "","","","";
+ };
+
+ sled2_fusb302: typec-portc@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ try-power-role = "sink";
+ data-role = "dual";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_VAR(3000, 12000, 3000)
+ PDO_PPS_APDO(3000, 11000, 3000)>;
+ op-sink-microwatt = <10000000>;
+ };
+ };
+};
+
+&i2c3 {
+ status = "okay";
+ /* TODO: Add ADC INA230 */
+
+ mp5023@40 {
+ compatible = "mps,mp5023";
+ reg = <0x40>;
+ };
+
+ tmp421@4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
+
+ sled3_ioexp: pca9539@76 {
+ compatible = "nxp,pca9539";
+ reg = <0x76>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "SLED3_MS_DETECT1","SLED3_VBUS_BMC_EN","SLED3_INA230_ALERT","SLED3_P12V_STBY_ALERT",
+ "SLED3_SSD_ALERT","SLED3_MS_DETECT0","SLED3_RST_CCG5","SLED3_FUSB302_INT",
+ "SLED3_MD_STBY_RESET","SLED3_MD_IOEXP_EN_FAULT","SLED3_MD_DIR","SLED3_MD_DECAY",
+ "SLED3_MD_MODE1","SLED3_MD_MODE2","SLED3_MD_MODE3","power-host3";
+ };
+
+ sled3_leds: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "led-sled3-amber","led-sled3-blue","SLED3_RST_IOEXP","",
+ "","","","",
+ "","","","",
+ "","","","";
+ };
+
+ sled3_fusb302: typec-portc@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ try-power-role = "sink";
+ data-role = "dual";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_VAR(3000, 12000, 3000)
+ PDO_PPS_APDO(3000, 11000, 3000)>;
+ op-sink-microwatt = <10000000>;
+ };
+ };
+};
+
+&i2c4 {
+ status = "okay";
+ /* TODO: Add ADC INA230 */
+
+ mp5023@40 {
+ compatible = "mps,mp5023";
+ reg = <0x40>;
+ };
+
+ tmp421@4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
+
+ sled4_ioexp: pca9539@76 {
+ compatible = "nxp,pca9539";
+ reg = <0x76>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "SLED4_MS_DETECT1","SLED4_VBUS_BMC_EN","SLED4_INA230_ALERT","SLED4_P12V_STBY_ALERT",
+ "SLED4_SSD_ALERT","SLED4_MS_DETECT0","SLED4_RST_CCG5","SLED4_FUSB302_INT",
+ "SLED4_MD_STBY_RESET","SLED4_MD_IOEXP_EN_FAULT","SLED4_MD_DIR","SLED4_MD_DECAY",
+ "SLED4_MD_MODE1","SLED4_MD_MODE2","SLED4_MD_MODE3","power-host4";
+ };
+
+ sled4_leds: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "led-sled4-amber","led-sled4-blue","SLED4_RST_IOEXP","",
+ "","","","",
+ "","","","",
+ "","","","";
+ };
+
+ sled4_fusb302: typec-portc@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ try-power-role = "sink";
+ data-role = "dual";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_VAR(3000, 12000, 3000)
+ PDO_PPS_APDO(3000, 11000, 3000)>;
+ op-sink-microwatt = <10000000>;
+ };
+ };
+};
+
+&i2c5 {
+ status = "okay";
+ /* TODO: Add ADC INA230 */
+
+ mp5023@40 {
+ compatible = "mps,mp5023";
+ reg = <0x40>;
+ };
+
+ tmp421@4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
+
+ sled5_ioexp: pca9539@76 {
+ compatible = "nxp,pca9539";
+ reg = <0x76>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "SLED5_MS_DETECT1","SLED5_VBUS_BMC_EN","SLED5_INA230_ALERT","SLED5_P12V_STBY_ALERT",
+ "SLED5_SSD_ALERT","SLED5_MS_DETECT0","SLED5_RST_CCG5","SLED5_FUSB302_INT",
+ "SLED5_MD_STBY_RESET","SLED5_MD_IOEXP_EN_FAULT","SLED5_MD_DIR","SLED5_MD_DECAY",
+ "SLED5_MD_MODE1","SLED5_MD_MODE2","SLED5_MD_MODE3","power-host5";
+ };
+
+ sled5_leds: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "led-sled5-amber","led-sled5-blue","SLED5_RST_IOEXP","",
+ "","","","",
+ "","","","",
+ "","","","";
+ };
+
+ sled5_fusb302: typec-portc@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ try-power-role = "sink";
+ data-role = "dual";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_VAR(3000, 12000, 3000)
+ PDO_PPS_APDO(3000, 11000, 3000)>;
+ op-sink-microwatt = <10000000>;
+ };
+ };
+};
+
+&i2c6 {
+ status = "okay";
+
+ eeprom@56 {
+ compatible = "atmel,24c64";
+ reg = <0x56>;
+ };
+
+ rtc@51 {
+ compatible = "nxp,pcf85263";
+ reg = <0x51>;
+ };
+};
+
+&i2c7 {
+ status = "okay";
+
+ eeprom@54 {
+ compatible = "atmel,24c64";
+ reg = <0x54>;
+ };
+};
+
+&i2c9 {
+ status = "okay";
+
+ tmp421@4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
+};
+
+&i2c10 {
+ status = "okay";
+
+ tmp421@4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
+
+ hdc1080@40 {
+ compatible = "ti,hdc1080";
+ reg = <0x40>;
+ };
+
+ front_leds: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "led-fault-identify","power-p5v-stby-good",
+ "power-p1v0-dvdd-good","power-p1v0-avdd-good",
+ "","","","",
+ "","","","",
+ "","","","";
+ };
+};
+
+&i2c12 {
+ status = "okay";
+
+ adm1278@11 {
+ compatible = "adi,adm1278";
+ reg = <0x11>;
+ };
+
+ tmp421@4c {
+ compatible = "ti,tmp421";
+ reg = <0x4c>;
+ };
+
+ tmp421@4d {
+ compatible = "ti,tmp421";
+ reg = <0x4d>;
+ };
+
+ fan_ioexp: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "presence-fan0","presence-fan1",
+ "presence-fan2","presence-fan3",
+ "power-fan0-good","power-fan1-good",
+ "power-fan2-good","power-fan3-good",
+ "","","","",
+ "","","","";
+ };
+};
+
+&i2c13 {
+ multi-master;
+ aspeed,hw-timeout-ms = <1000>;
+ status = "okay";
+};
+
+&gpio0 {
+ gpio-line-names =
+ /*A0-A7*/ "","","","","","","","",
+ /*B0-B7*/ "","","SEL_SPI2_MUX","SPI2_MUX1",
+ "SPI2_MUX2","SPI2_MUX3","","",
+ /*C0-C7*/ "","","","","","","","",
+ /*D0-D7*/ "","","","","","","","",
+ /*E0-E7*/ "","","","","","","","",
+ /*F0-F7*/ "","","","","","","","",
+ /*G0-G7*/ "","SWITCH_FRU_MUX","","","","","","",
+ /*H0-H7*/ "presence-riser1","presence-riser2",
+ "presence-sled0","presence-sled1",
+ "presence-sled2","presence-sled3",
+ "presence-sled4","presence-sled5",
+ /*I0-I7*/ "REV_ID0","","REV_ID1","REV_ID2",
+ "","","","",
+ /*J0-J7*/ "","","","","","","","",
+ /*K0-K7*/ "","","","","","","","",
+ /*L0-L7*/ "","","","","","","","",
+ /*M0-M7*/ "ALERT_SLED0","ALERT_SLED1",
+ "ALERT_SLED2","ALERT_SLED3",
+ "ALERT_SLED4","ALERT_SLED5",
+ "P12V_AUX_ALERT1","",
+ /*N0-N7*/ "","","","","","","","",
+ /*O0-O7*/ "","","","",
+ "","BOARD_ID0","BOARD_ID1","BOARD_ID2",
+ /*P0-P7*/ "","","","","","","","",
+ /*Q0-Q7*/ "","","","","","","","",
+ /*R0-R7*/ "","","","","","","","",
+ /*S0-S7*/ "","","","BAT_DETECT",
+ "BMC_BT_WP0","BMC_BT_WP1","","",
+ /*T0-T7*/ "","","","","","","","",
+ /*U0-U7*/ "","","","","","","","",
+ /*V0-V7*/ "","RST_BMC_MVL","","",
+ "USB2_SEL0_A","USB2_SEL1_A",
+ "USB2_SEL0_B","USB2_SEL1_B",
+ /*W0-W7*/ "RST_FRONT_IOEXP","","","","","","","",
+ /*X0-X7*/ "","","","","","","","",
+ /*Y0-Y7*/ "","","BSM_FLASH_LATCH","","","","","",
+ /*Z0-Z7*/ "","","","","","","","";
+};
+
+&adc0 {
+ vref = <1800>;
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+ &pinctrl_adc2_default &pinctrl_adc3_default
+ &pinctrl_adc4_default &pinctrl_adc5_default
+ &pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+ vref = <2500>;
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+ &pinctrl_adc10_default &pinctrl_adc11_default
+ &pinctrl_adc12_default &pinctrl_adc13_default
+ &pinctrl_adc14_default &pinctrl_adc15_default>;
+};
--
2.25.1
Powered by blists - more mailing lists