Message-ID: <6debe673-8c88-53f1-badc-23f2dfc15350@xilinx.com>
Date:   Mon, 13 Dec 2021 13:40:35 +0530
From:   Tanmay Shah <tanmay.shah@...inx.com>
To:     Mathieu Poirier <mathieu.poirier@...aro.org>
CC:     Bjorn Andersson <bjorn.andersson@...aro.org>,
        Rob Herring <robh+dt@...nel.org>,
        Michal Simek <michal.simek@...inx.com>,
        "Laurent Pinchart" <laurent.pinchart@...asonboard.com>,
        Ben Levinsky <ben.levinsky@...inx.com>,
        Bill Mills <bill.mills@...aro.org>,
        "Sergei Korneichuk" <sergei.korneichuk@...inx.com>,
        <linux-remoteproc@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
        <devicetree@...r.kernel.org>,
        <linux-arm-kernel@...ts.infradead.org>
Subject: Re: [PATCH v2 6/6] drivers: remoteproc: Add Xilinx r5 remoteproc
 driver

Hi Mathieu,

Thanks for reviews. Please find my comments below.

On 12/4/21 12:25 AM, Mathieu Poirier wrote:
> Hi Tanmay,
>
> On Mon, Nov 22, 2021 at 10:20:50PM -0800, Tanmay Shah wrote:
>> This driver enables r5f dual core Real time Processing Unit subsystem
>> available on Xilinx Zynq Ultrascale MPSoC Platform. RPU subsystem
>> (cluster) can be configured in different modes e.g. split mode in which
>> two r5f cores work independent of each other and lock-step mode in which
>> both r5f cores execute same code clock-for-clock and notify if the
>> result is different.
>>
>> The Xilinx r5 Remoteproc Driver boots the RPU cores via calls to the Xilinx
>> Platform Management Unit that handles the R5 configuration, memory access
>> and R5 lifecycle management. The interface to this manager is done in this
>> driver via zynqmp_pm_* function calls.
>>
>> Signed-off-by: Ben Levinsky<ben.levinsky@...inx.com>
>> Signed-off-by: Tanmay Shah<tanmay.shah@...inx.com>
>> ---
>>   drivers/remoteproc/Kconfig              |  12 +
>>   drivers/remoteproc/Makefile             |   1 +
>>   drivers/remoteproc/xlnx_r5_remoteproc.c | 959 ++++++++++++++++++++++++
>>   3 files changed, 972 insertions(+)
>>   create mode 100644 drivers/remoteproc/xlnx_r5_remoteproc.c
>>
>> diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig
>> index f30d00a3aabe..27f66910d8d3 100644
>> --- a/drivers/remoteproc/Kconfig
>> +++ b/drivers/remoteproc/Kconfig
>> @@ -315,6 +315,18 @@ config TI_K3_R5_REMOTEPROC
>>   	  It's safe to say N here if you're not interested in utilizing
>>   	  a slave processor.
>>   
>> +config XLNX_R5_REMOTEPROC
>> +	tristate "Xilinx R5 remoteproc support"
>> +	depends on PM && ARCH_ZYNQMP
>> +	depends on ZYNQMP_FIRMWARE
>> +	select RPMSG_VIRTIO
>> +	select ZYNQMP_IPI_MBOX
>> +	help
>> +	  Say y or m here to support Xilinx R5 remote processors via the remote
>> +	  processor framework.
>> +
>> +	  It's safe to say N if not interested in using RPU r5f cores.
>> +
>>   endif # REMOTEPROC
>>   
>>   endmenu
>> diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile
>> index bb26c9e4ef9c..334a8bed4c14 100644
>> --- a/drivers/remoteproc/Makefile
>> +++ b/drivers/remoteproc/Makefile
>> @@ -35,3 +35,4 @@ obj-$(CONFIG_ST_SLIM_REMOTEPROC)	+= st_slim_rproc.o
>>   obj-$(CONFIG_STM32_RPROC)		+= stm32_rproc.o
>>   obj-$(CONFIG_TI_K3_DSP_REMOTEPROC)	+= ti_k3_dsp_remoteproc.o
>>   obj-$(CONFIG_TI_K3_R5_REMOTEPROC)	+= ti_k3_r5_remoteproc.o
>> +obj-$(CONFIG_XLNX_R5_REMOTEPROC)	+= xlnx_r5_remoteproc.o
>> diff --git a/drivers/remoteproc/xlnx_r5_remoteproc.c b/drivers/remoteproc/xlnx_r5_remoteproc.c
>> new file mode 100644
>> index 000000000000..c2167fd3869d
>> --- /dev/null
>> +++ b/drivers/remoteproc/xlnx_r5_remoteproc.c
>> @@ -0,0 +1,959 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * ZynqMP R5 Remote Processor driver
>> + *
>> + */
>> +
>> +#include <dt-bindings/power/xlnx-zynqmp-power.h>
>> +#include <linux/firmware/xlnx-zynqmp.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/kernel.h>
>> +#include <linux/list.h>
>> +#include <linux/mailbox_client.h>
>> +#include <linux/mailbox/zynqmp-ipi-message.h>
>> +#include <linux/module.h>
>> +#include <linux/of_address.h>
>> +#include <linux/of_platform.h>
>> +#include <linux/of_reserved_mem.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/remoteproc.h>
>> +#include <linux/skbuff.h>
>> +#include <linux/sysfs.h>
>> +
>> +#include "remoteproc_internal.h"
>> +
>> +/* settings for RPU cluster mode */
>> +enum zynqmp_r5_cluster_mode {
>> +	SPLIT_MODE = 0, // RPU cluster mode when cores run as separate processor
>> +	LOCKSTEP_MODE = 1, // cores execute same code in lockstep,clk-for-clk
>> +	SINGLE_CPU_MODE = 2, // core0 is held in reset and only core1 runs
> Please use C style comments, i.e /*...*/
>
>> +};
>> +
>> +/**
>> + * struct mem_bank_data - Memory Bank description
>> + *
>> + * @addr: Start address of memory bank
>> + * @size: Size of Memory bank
>> + * @pm_domain_id: Power-domains id of memory bank for firmware to turn on/off
>> + * @bank_name: name of the bank for remoteproc framework
>> + */
>> +struct mem_bank_data {
>> +	phys_addr_t addr;
>> +	size_t size;
>> +	enum pm_node_id pm_domain_id;
>> +	char *bank_name;
>> +};
>> +
>> +static const struct mem_bank_data zynqmp_tcm_banks[] = {
>> +	{0xffe00000UL, 0x10000UL, PD_R5_0_ATCM, "atcm0"}, /* TCM 64KB each */
>> +	{0xffe20000UL, 0x10000UL, PD_R5_0_BTCM, "btcm0"},
>> +	{0xffe90000UL, 0x10000UL, PD_R5_1_ATCM, "atcm1"},
>> +	{0xffeb0000UL, 0x10000UL, PD_R5_1_BTCM, "btcm1"},
>> +};
> Bizarre - more comments on this below...
I know ideally it should have been in yaml bindings and we should parse 
it from device-tree. Please find my explanation below for this approach.
>> +
>> +/**
>> + * struct zynqmp_r5_core - ZynqMP R5 core structure
>> + *
>> + * @dev: device of RPU instance
>> + * @np: device node of RPU instance
>> + * @tcm_bank_count: number TCM banks accessible to this RPU
>> + * @tcm_banks: array of each TCM bank data
>> + * @res_mem_count: number of Reserved Memory regions per core
>> + * @res_mem: array of reserved memory regions
>> + * @rproc: rproc handle
>> + * @pm_domain_id: RPU CPU power domain id
>> + */
>> +struct zynqmp_r5_core {
>> +	struct device *dev;
>> +	struct device_node *np;
>> +	int tcm_bank_count;
>> +	struct mem_bank_data *tcm_banks;
>> +	int res_mem_count;
>> +	struct reserved_mem *res_mem;
>> +	struct rproc *rproc;
>> +	enum pm_node_id pm_domain_id;
>> +};
>> +
>> +/**
>> + * struct zynqmp_r5_cluster - ZynqMP R5 cluster structure
>> + *
>> + * @dev: r5f subsystem cluster device node
>> + * @mode: cluster mode of type zynqmp_r5_cluster_mode
>> + * @core_count: number of r5 cores used for this cluster mode
>> + * @r5_cores: Array of r5 cores of type struct zynqmp_r5_core
>> + */
>> +struct zynqmp_r5_cluster {
>> +	struct device *dev;
>> +	enum  zynqmp_r5_cluster_mode mode;
>> +	int core_count;
>> +	struct zynqmp_r5_core *r5_cores;
>> +};
>> +
>> +/*
>> + * zynqmp_r5_set_mode - set RPU operation mode
>> + *
>> + * set RPU operation mode
>> + *
>> + * Return: 0 for success, negative value for failure
>> + */
>> +static int zynqmp_r5_set_mode(struct zynqmp_r5_core *r5_core,
>> +			      enum zynqmp_r5_cluster_mode rpu_mode)
>> +{
>> +	enum rpu_tcm_comb tcm_mode;
>> +	int ret, reg_val;
>> +
>> +	reg_val = (rpu_mode == LOCKSTEP_MODE ? 0 : 1);
>> +
>> +	ret = zynqmp_pm_set_rpu_mode(r5_core->pm_domain_id, reg_val);
>> +	if (ret < 0) {
>> +		pr_err("failed to set RPU mode\n");
>> +		return ret;
>> +	}
>> +
>> +	tcm_mode = (rpu_mode == LOCKSTEP_MODE) ?
>> +		    PM_RPU_TCM_COMB : PM_RPU_TCM_SPLIT;
>> +	ret = zynqmp_pm_set_tcm_config(r5_core->pm_domain_id, tcm_mode);
>> +	if (ret < 0)
>> +		pr_err("failed to configure TCM\n");
>> +
>> +	return ret;
>> +}
>> +
>> +/*
>> + * zynqmp_r5_rproc_start
>> + * @rproc: single R5 core's corresponding rproc instance
>> + *
>> + * Start R5 Core from designated boot address.
>> + *
>> + * return 0 on success, otherwise non-zero value on failure
>> + */
>> +static int zynqmp_r5_rproc_start(struct rproc *rproc)
>> +{
>> +	struct zynqmp_r5_core *r5_core = rproc->priv;
>> +	enum rpu_boot_mem bootmem;
>> +	int ret;
>> +
>> +	if (!r5_core) {
>> +		pr_err("can't get r5 core\n");
>> +		return -EINVAL;
>> +	}
>> +
>> +	bootmem = (rproc->bootaddr >= 0xFFFC0000) ?
>> +		   PM_RPU_BOOTMEM_HIVEC : PM_RPU_BOOTMEM_LOVEC;
>> +
>> +	dev_dbg(r5_core->dev, "RPU boot addr 0x%llx from %s.", rproc->bootaddr,
>> +		bootmem == PM_RPU_BOOTMEM_HIVEC ? "OCM" : "TCM");
>> +
>> +	ret = zynqmp_pm_request_wake(r5_core->pm_domain_id, 1,
>> +				     bootmem, ZYNQMP_PM_REQUEST_ACK_NO);
>> +	if (ret)
>> +		pr_err("failed to start RPU = %d\n", r5_core->pm_domain_id);
>> +	return ret;
>> +}
>> +
>> +/*
>> + * zynqmp_r5_rproc_stop
>> + * @rproc: single R5 core's corresponding rproc instance
>> + *
>> + * Power down  R5 Core.
>> + *
>> + * return 0 on success, otherwise non-zero value on failure
>> + */
>> +static int zynqmp_r5_rproc_stop(struct rproc *rproc)
>> +{
>> +	struct zynqmp_r5_core *r5_core = rproc->priv;
>> +	int ret;
>> +
>> +	ret = zynqmp_pm_force_pwrdwn(r5_core->pm_domain_id,
>> +				     ZYNQMP_PM_REQUEST_ACK_BLOCKING);
>> +	if (ret)
>> +		pr_err("failed to stop remoteproc RPU %d\n", ret);
>> +
>> +	return ret;
>> +}
>> +
>> +/*
>> + * zynqmp_r5_rproc_mem_map
>> + * @rproc: single R5 core's corresponding rproc instance
>> + * @mem: mem entry to map
>> + *
>> + * Callback to map va for memory-region's carveout.
>> + *
>> + * return 0 on success, otherwise non-zero value on failure
>> + */
>> +static int zynqmp_r5_rproc_mem_map(struct rproc *rproc,
>> +				   struct rproc_mem_entry *mem)
>> +{
>> +	void __iomem *va;
>> +
>> +	va = ioremap_wc(mem->dma, mem->len);
>> +	if (IS_ERR_OR_NULL(va))
>> +		return -ENOMEM;
>> +
>> +	mem->va = (void *)va;
>> +
>> +	return 0;
>> +}
>> +
>> +/*
>> + * zynqmp_r5_rproc_mem_unmap
>> + * @rproc: single R5 core's corresponding rproc instance
>> + * @mem: mem entry to unmap
>> + *
>> + * Unmap memory-region carveout
>> + *
>> + * return 0 on success, otherwise non-zero value on failure
>> + */
>> +static int zynqmp_r5_rproc_mem_unmap(struct rproc *rproc,
>> +				     struct rproc_mem_entry *mem)
>> +{
>> +	iounmap((void __iomem *)mem->va);
>> +	return 0;
>> +}
>> +
>> +/*
>> + * add_mem_regions
>> + * @rproc: single R5 core's corresponding rproc instance
>> + *
>> + * Construct rproc mem carveouts from carveout provided in
>> + * memory-region property
>> + *
>> + * return 0 on success, otherwise non-zero value on failure
>> + */
>> +static int add_mem_regions(struct rproc *rproc)
>> +{
>> +	struct device *dev;
>> +	struct rproc_mem_entry *mem;
>> +	struct reserved_mem *rmem;
>> +	struct zynqmp_r5_core *r5_core;
>> +	int i;
>> +
>> +	r5_core = rproc->priv;
>> +	dev = r5_core->dev;
>> +
>> +	/* Register associated reserved memory regions */
>> +	for (i = 0; i < r5_core->res_mem_count; i++) {
>> +		rmem = &r5_core->res_mem[i];
>> +		mem = rproc_mem_entry_init(dev, NULL,
>> +					   (dma_addr_t)rmem->base,
>> +					   rmem->size, rmem->base,
>> +					   zynqmp_r5_rproc_mem_map,
>> +					   zynqmp_r5_rproc_mem_unmap,
>> +					   rmem->name);
>> +		if (IS_ERR_OR_NULL(mem))
>> +			return -ENOMEM;
>> +
>> +		rproc_add_carveout(rproc, mem);
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +/*
>> + * zynqmp_r5_rproc_mem_unmap
>> + * @rproc: single R5 core's corresponding rproc instance
>> + * @mem: mem entry to unmap
>> + *
>> + * Unmap TCM banks when powering down R5 core.
>> + *
>> + * return 0 on success, otherwise non-zero value on failure
>> + */
>> +static int tcm_mem_unmap(struct rproc *rproc, struct rproc_mem_entry *mem)
>> +{
>> +	struct zynqmp_r5_core *r5_core;
>> +	int i;
>> +	enum pm_node_id pm_domain_id;
>> +
>> +	r5_core = rproc->priv;
>> +	if (!r5_core) {
>> +		pr_err("r5 core is not available\n");
>> +		return -EINVAL;
>> +	}
>> +
>> +	iounmap((void __iomem *)mem->va);
>> +
>> +	for (i = 0; i < r5_core->tcm_bank_count; i++) {
>> +		pm_domain_id = r5_core->tcm_banks[i].pm_domain_id;
>> +		if (zynqmp_pm_release_node(pm_domain_id))
>> +			pr_warn("can't turn off TCM bank %d", pm_domain_id);
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +/*
>> + * tcm_mem_map
>> + * @rproc: single R5 core's corresponding rproc instance
>> + * @mem: mem entry to initialize the va and da fields of
>> + *
>> + * Given TCM bank entry, this callback will set device address for R5
>> + * running on TCM and also setup virtual address for TCM bank
>> + * remoteproc carveout.
>> + *
>> + * return 0 on success, otherwise non-zero value on failure
>> + */
>> +static int tcm_mem_map(struct rproc *rproc,
>> +			 struct rproc_mem_entry *mem)
>> +{
>> +	void __iomem *va;
>> +
>> +	va = ioremap_wc(mem->dma, mem->len);
>> +	if (IS_ERR_OR_NULL(va))
>> +		return -ENOMEM;
>> +
>> +	/* Update memory entry va */
>> +	mem->va = (void *)va;
>> +
>> +	/* clear TCMs */
>> +	memset_io(va, 0, mem->len);
>> +
>> +	/*
>> +	 * The R5s expect their TCM banks to be at address 0x0 and 0x2000,
>> +	 * while on the Linux side they are at 0xffexxxxx.
>> +	 *
>> +	 * Zero out the high 12 bits of the address. This will give
>> +	 * expected values for TCM Banks 0A and 0B (0x0 and 0x20000).
>> +	 */
>> +	mem->da &= 0x000fffff;
>> +
>> +	/*
>> +	 * TCM Banks 1A and 1B still have to be translated.
>> +	 *
>> +	 * Below handle these two banks' absolute addresses (0xffe90000 and
>> +	 * 0xffeb0000) and convert to the expected relative addresses
>> +	 * (0x0 and 0x20000).
>> +	 */
>> +	if (mem->da == 0x90000 || mem->da == 0xB0000)
>> +		mem->da -= 0x90000;
>> +
>> +	/* if translated TCM bank address is not valid report error */
>> +	if (mem->da != 0x0 && mem->da != 0x20000) {
>> +		dev_err(&rproc->dev, "invalid TCM address: %x\n", mem->da);
>> +		return -EINVAL;
>> +	}
>> +	return 0;
>> +}
>> +
>> +static int add_tcm_carveout_split_mode(struct rproc *rproc)
>> +{
>> +	int i, num_banks, ret;
>> +	struct rproc_mem_entry *mem;
>> +	enum pm_node_id pm_domain_id;
>> +	u32 bank_addr;
>> +	size_t bank_size = 0;
>> +	char *bank_name;
>> +	struct device *dev;
>> +	struct zynqmp_r5_core *r5_core;
>> +
>> +	r5_core = (struct zynqmp_r5_core *)rproc->priv;
>> +	if (!r5_core)
>> +		return -EINVAL;
>> +
>> +	dev = r5_core->dev;
>> +
>> +	/* go through zynqmp banks for r5 node */
>> +	num_banks = r5_core->tcm_bank_count;
>> +	if (num_banks <= 0) {
>> +		dev_err(dev, "need to specify TCM banks\n");
>> +		return -EINVAL;
>> +	}
>> +
>> +	for (i = 0; i < num_banks; i++) {
>> +		bank_addr = (u32)r5_core->tcm_banks[i].addr;
>> +		bank_name = r5_core->tcm_banks[i].bank_name;
>> +		bank_size = r5_core->tcm_banks[i].size;
>> +		pm_domain_id = r5_core->tcm_banks[i].pm_domain_id;
>> +
>> +		ret = zynqmp_pm_request_node(pm_domain_id,
>> +					     ZYNQMP_PM_CAPABILITY_ACCESS, 0,
>> +					     ZYNQMP_PM_REQUEST_ACK_BLOCKING);
>> +		if (ret < 0) {
>> +			dev_err(dev, "failed to turn on TCM %d", pm_domain_id);
>> +			return ret;
>> +		}
>> +
>> +		dev_dbg(dev, "TCM carveout split mode %s addr=%x, size=0x%lx",
>> +			bank_name, bank_addr, bank_size);
>> +
>> +		/* add carveout */
>> +		mem = rproc_mem_entry_init(dev, NULL, bank_addr,
>> +					   bank_size, bank_addr,
>> +					   tcm_mem_map, tcm_mem_unmap,
>> +					   bank_name);
>> +		if (IS_ERR_OR_NULL(mem)) {
>> +			/* Turn off all TCM banks turned on before */
>> +			do {
>> +				pm_domain_id = r5_core->tcm_banks[i].pm_domain_id;
>> +				ret = zynqmp_pm_release_node((u32)pm_domain_id);
>> +				if (ret)
>> +					dev_warn(dev,
>> +						 "fail to release node: %x, %x\n",
>> +						 (u32)pm_domain_id, ret);
>> +			} while (i--);
>> +			return -ENOMEM;
>> +		}
>> +
>> +		rproc_add_carveout(rproc, mem);
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +static int add_tcm_carveout_lockstep_mode(struct rproc *rproc)
>> +{
>> +	int i, num_banks, ret;
>> +	struct rproc_mem_entry *mem;
>> +	enum pm_node_id pm_domain_id;
>> +	u32 bank_addr;
>> +	size_t bank_size = 0;
>> +	char *bank_name;
>> +	struct device *dev;
>> +	struct platform_device *parent_pdev;
>> +	struct zynqmp_r5_cluster *cluster;
>> +	struct zynqmp_r5_core *r5_core;
>> +
>> +	r5_core = (struct zynqmp_r5_core *)rproc->priv;
>> +	if (!r5_core)
>> +		return -EINVAL;
>> +
>> +	dev = r5_core->dev;
>> +	if (!dev) {
>> +		pr_err("r5 core device unavailable\n");
>> +		return -ENODEV;
>> +	}
>> +
>> +	/* go through zynqmp banks for r5 node */
>> +	num_banks = r5_core->tcm_bank_count;
>> +	if (num_banks <= 0) {
>> +		dev_err(dev, "need to specify TCM banks\n");
>> +		return -EINVAL;
>> +	}
>> +
>> +	bank_addr = (u32)r5_core->tcm_banks[0].addr;
>> +	bank_name = r5_core->tcm_banks[0].bank_name;
>> +	for (i = 0; i < num_banks; i++) {
>> +		bank_size += r5_core->tcm_banks[i].size;
>> +		pm_domain_id = r5_core->tcm_banks[i].pm_domain_id;
>> +
>> +		ret = zynqmp_pm_request_node(pm_domain_id,
>> +					     ZYNQMP_PM_CAPABILITY_ACCESS, 0,
>> +					     ZYNQMP_PM_REQUEST_ACK_BLOCKING);
>> +		if (ret < 0) {
>> +			dev_err(dev, "failed to turn on TCM %d", pm_domain_id);
>> +			return ret;
>> +		}
>> +	}
>> +
>> +	dev_dbg(dev, "TCM add carveout lockstep mode %s addr=0x%x, size=0x%lx",
>> +		bank_name, bank_addr, bank_size);
>> +
>> +	/* add carveout */
>> +	mem = rproc_mem_entry_init(dev, NULL, bank_addr,
>> +				   bank_size, bank_addr,
>> +				   tcm_mem_map, tcm_mem_unmap,
>> +				   bank_name);
>> +	if (IS_ERR_OR_NULL(mem)) {
>> +		for (i = 0; i < num_banks; i++) {
>> +			pm_domain_id = r5_core->tcm_banks[i].pm_domain_id;
>> +			ret = zynqmp_pm_release_node((u32)pm_domain_id);
>> +			if (ret)
>> +				dev_warn(dev,
>> +					 "fail to release node: %x ret: %x\n",
>> +					 (u32)pm_domain_id, ret);
>> +		}
>> +		return -ENOMEM;
>> +	}
>> +
>> +	rproc_add_carveout(rproc, mem);
>> +
>> +	return 0;
>> +}
>> +
>> +/*
>> + * add_tcm_banks()
>> + * @rproc: single R5 core's corresponding rproc instance
>> + *
>> + * Given R5 node in remoteproc instance
>> + * allocate remoteproc carveout for TCM memory
>> + * needed for firmware to be loaded
>> + *
>> + * return 0 on success, otherwise non-zero value on failure
>> + */
>> +static int add_tcm_banks(struct rproc *rproc)
>> +{
>> +	struct device *dev;
>> +	struct platform_device *parent_pdev;
>> +	struct zynqmp_r5_cluster *cluster;
>> +	struct zynqmp_r5_core *r5_core;
>> +
>> +	r5_core = (struct zynqmp_r5_core *)rproc->priv;
>> +	if (!r5_core)
>> +		return -EINVAL;
>> +
>> +	dev = r5_core->dev;
>> +	if (!dev) {
>> +		pr_err("r5 core device unavailable\n");
>> +		return -ENODEV;
>> +	}
>> +
>> +	parent_pdev = to_platform_device(dev->parent);
>> +	if (!parent_pdev) {
>> +		dev_err(dev, "parent platform dev unavailable\n");
>> +		return -ENODEV;
>> +	}
>> +
>> +	cluster = platform_get_drvdata(parent_pdev);
>> +	if (!cluster) {
>> +		dev_err(&parent_pdev->dev, "Invalid driver data\n");
>> +		return -EINVAL;
>> +	}
>> +
>> +	if (cluster->mode == SPLIT_MODE)
>> +		return add_tcm_carveout_split_mode(rproc);
>> +	else if (cluster->mode == LOCKSTEP_MODE)
>> +		return add_tcm_carveout_lockstep_mode(rproc);
>> +
>> +	dev_err(cluster->dev, "invalid cluster mode\n");
>> +	return -EINVAL;
>> +}
>> +
>> +/*
>> + * zynqmp_r5_parse_fw()
>> + * @rproc: single R5 core's corresponding rproc instance
>> + * @fw: ptr to firmware to be loaded onto r5 core
>> + *
>> + * When loading firmware, ensure the necessary carveouts are in remoteproc
>> + *
>> + * return 0 on success, otherwise non-zero value on failure
>> + */
>> +static int zynqmp_r5_parse_fw(struct rproc *rproc, const struct firmware *fw)
>> +{
>> +	int ret;
>> +	struct zynqmp_r5_core *r5_core;
>> +	struct device *dev;
>> +
>> +	r5_core = rproc->priv;
>> +	if (!r5_core) {
>> +		dev_err(&rproc->dev, "r5 core not available\n");
>> +		return -EINVAL;
>> +	}
>> +
>> +	dev = r5_core->dev;
>> +
>> +	ret = add_tcm_banks(rproc);
>> +	if (ret) {
>> +		dev_err(dev, "failed to get TCM banks, err %d\n", ret);
>> +		return ret;
>> +	}
>> +
>> +	ret = add_mem_regions(rproc);
>> +	if (ret)
>> +		dev_warn(dev, "failed to get reserve mem regions %d\n", ret);
>> +
>> +	ret = rproc_elf_load_rsc_table(rproc, fw);
>> +	if (ret == -EINVAL) {
>> +		/*
>> +		 * resource table only required for IPC.
>> +		 * if not present, this is not necessarily an error;
>> +		 * for example, loading r5 hello world application
>> +		 * so simply inform user and keep going.
>> +		 */
>> +		dev_info(&rproc->dev, "no resource table found.\n");
>> +		ret = 0;
>> +	}
>> +	return ret;
>> +}
>> +
>> +static struct rproc_ops zynqmp_r5_rproc_ops = {
>> +	.start		= zynqmp_r5_rproc_start,
>> +	.stop		= zynqmp_r5_rproc_stop,
>> +	.load		= rproc_elf_load_segments,
>> +	.parse_fw	= zynqmp_r5_parse_fw,
>> +	.find_loaded_rsc_table = rproc_elf_find_loaded_rsc_table,
>> +	.sanity_check	= rproc_elf_sanity_check,
>> +	.get_boot_addr	= rproc_elf_get_boot_addr,
>> +};
>> +
>> +static void zynqmp_r5_print_dt_node_info(struct zynqmp_r5_cluster *cluster)
>> +{
>> +	int i, j, k;
>> +	struct zynqmp_r5_core *r5_core;
>> +
>> +	dev_dbg(cluster->dev, "Printing dt node info\n");
> Why mixing dev_dbg() and pr_debug()?  Please pick one and stick with it.
>
> Even for debug level output this is very chatty - is all that information really
> needed when it is already available in /proc/device-tree?

I kept this function for debugging. However, looks like we can use 
/proc/device-tree for same purpose, so I will remove this function. 
Thanks for this suggestion.

>> +
>> +	pr_debug("cluster mode = %d\n", cluster->mode);
>> +	pr_debug("r5f cluster in %s mode\n", (cluster->mode == 0) ? "SPLIT" :
>> +		 cluster->mode == 1 ? "LOCKSTEP" : "SINGLE_CPU");
>> +	pr_debug("r5f num cores = %d\n", cluster->core_count);
>> +
>> +	for (i = 0; i < cluster->core_count; i++) {
>> +		r5_core = &cluster->r5_cores[i];
>> +		if (!r5_core) {
>> +			pr_err("can't get r5_core\n");
>> +			continue;
>> +		}
>> +
>> +		pr_debug("r5 core %d nodes\n", i);
>> +		pr_debug("TCM banks = %d\n", r5_core->tcm_bank_count);
>> +		for (k = 0; k < r5_core->tcm_bank_count; k++) {
>> +			pr_debug("tcm %d addr=0x%llx size=0x%lx, pm_id=%d, %s\n",
>> +				 k, r5_core->tcm_banks[k].addr,
>> +				 r5_core->tcm_banks[k].size,
>> +				 r5_core->tcm_banks[k].pm_domain_id,
>> +				 r5_core->tcm_banks[k].bank_name);
>> +		}
>> +
>> +		pr_debug("reserve mem regions = %d\n", r5_core->res_mem_count);
>> +
>> +		for (j = 0; j < r5_core->res_mem_count; j++) {
>> +			pr_debug("mem %d addr=0x%llx, size=0x%llx, name=%s\n",
>> +				 j, r5_core->res_mem[j].base,
>> +				 r5_core->res_mem[j].size,
>> +				 r5_core->res_mem[j].name);
>> +		}
>> +	}
>> +}
>> +
>> +/**
>> + * zynqmp_r5_add_rproc_core() - Probes ZynqMP R5 processor device node
>> + *		       this is called for each individual R5 core to
>> + *		       set up mailbox, Xilinx platform manager unique ID,
>> + *		       add to rproc core
>> + *
>> + * @r5_core: zynqmp_r5_core r5 core object to initialize
>> + *
>> + * Return: 0 for success, negative value for failure.
>> + */
>> +static int zynqmp_r5_add_rproc_core(struct zynqmp_r5_core *r5_core)
>> +{
>> +	int ret;
>> +	struct rproc *r5_rproc;
>> +	struct device *dev;
>> +
>> +	dev = r5_core->dev;
>> +
>> +	/* Set up DMA mask */
>> +	ret = dma_set_coherent_mask(dev, DMA_BIT_MASK(32));
>> +	if (ret)
>> +		return ret;
>> +
>> +	/* Allocate remoteproc instance */
>> +	r5_rproc = devm_rproc_alloc(dev, dev_name(dev), &zynqmp_r5_rproc_ops,
>> +				    NULL, sizeof(struct zynqmp_r5_core));
>> +	if (IS_ERR_OR_NULL(r5_rproc))
>> +		return -ENOMEM;
>> +
>> +	r5_rproc->auto_boot = false;
>> +	r5_rproc->priv = r5_core;
>> +
>> +	/* Add R5 remoteproc */
>> +	ret = devm_rproc_add(dev, r5_rproc);
>> +	if (ret) {
>> +		pr_err("failed to add r5 remoteproc\n");
>> +		return ret;
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +static int zynqmp_r5_get_tcm_node(struct zynqmp_r5_cluster *cluster)
>> +{
>> +	int tcm_bank_count, tcm_node;
>> +	int i = 0, j;
>> +	struct zynqmp_r5_core *r5_core;
>> +	const struct mem_bank_data *tcm = zynqmp_tcm_banks;
>> +	struct device *dev = cluster->dev;
>> +
>> +	/* ToDo: Use predefined TCM address space values from driver until
>> +	 * system-dt spec is not final fot TCM
>> +	 */
> Multilined comment should be as follow:
>
>          /*
>           * ToDo: Use predefined TCM address space values from driver until
> 	 * system-dt spec is not final fot TCM
>           */
>
> s/"final fot TCM"/"final for TCM"
>
> Any reason this can't be done with "reg" properties like TI did for K3?  It
> would be nice to have TCMs included in the yaml file example.
>
R5 TCM on Xilinx platforms contains separate power-domains than RPU 
power-domains. So, I believe they can be operated separately than RPU. 
That is why I chose not to include as reg property. I believe we will 
include TCM as sram property in future.

Now, explanation about why TCM is hardcode in driver:

When I started developing driver, system-dt spec was in progress, to 
avoid extra maintenance effort I defined TCM information in driver 
instead of defining them in YAML.
I agree with idea that there is no need to maintain two separate 
bindings and until system-dt specs are maturing we can hardcode TCM 
related information driver. This was discussed previously here: 
https://lore.kernel.org/all/CAL_JsqLGo380SRYska+xGgJhgF8NCRvY56ewafvSCU6c-LmhZw@mail.gmail.com/

Patchwork link for the same: 
https://patchwork.kernel.org/project/linux-remoteproc/patch/1587749770-15082-5-git-send-email-ben.levinsky@xilinx.com/#23414963

Also, I will sync with system-dt team about its current status and keep 
updating about system-dt specs.

Please let me know your opinion / suggestion for any alternative approach.


I agree with rest of the comments in this thread, and I will address 
them all in next revision.

>> +	tcm_bank_count = ARRAY_SIZE(zynqmp_tcm_banks);
>> +
>> +	/* count per core tcm banks */
>> +	tcm_bank_count = tcm_bank_count / cluster->core_count;
>> +
>> +	/* r5 core 0 will use all of TCM banks in lockstep mode.
>> +	 * In split mode, r5 core0 will use 128k and r5 core1 will use another
>> +	 * 128k. Assign TCM banks to each core accordingly
>> +	 */
>> +	tcm_node = 0;
>> +	for (j = 0; j < cluster->core_count; j++) {
>> +		r5_core = &cluster->r5_cores[j];
>> +		r5_core->tcm_banks = devm_kzalloc(dev, sizeof(struct mem_bank_data) *
>> +						  tcm_bank_count, GFP_KERNEL);
>> +		if (IS_ERR_OR_NULL(r5_core->tcm_banks))
>> +			return -ENOMEM;
>> +
>> +		for (i = 0; i < tcm_bank_count; i++) {
>> +			/* Use pre-defined TCM reg values.
>> +			 * Eventually this should be replaced by values
>> +			 * parsed from dts.
>> +			 */
>> +			r5_core->tcm_banks[i].addr = tcm[tcm_node].addr;
>> +			r5_core->tcm_banks[i].size = tcm[tcm_node].size;
>> +			r5_core->tcm_banks[i].pm_domain_id = tcm[tcm_node].pm_domain_id;
>> +			r5_core->tcm_banks[i].bank_name = tcm[tcm_node].bank_name;
>> +			tcm_node++;
>> +		}
>> +
>> +		r5_core->tcm_bank_count = tcm_bank_count;
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +static int zynqmp_r5_get_mem_region_node(struct zynqmp_r5_core *r5_core)
>> +{
>> +	int res_mem_count, i;
>> +	struct device *dev;
>> +	struct device_node *np, *rmem_np;
>> +	struct reserved_mem *rmem;
>> +
>> +	dev = r5_core->dev;
>> +
>> +	np = r5_core->np;
>> +	if (IS_ERR_OR_NULL(np)) {
>> +		pr_err("invalid device node of r5 core\n");
>> +		return -EINVAL;
>> +	}
>> +
>> +	res_mem_count = of_property_count_elems_of_size(np, "memory-region",
>> +							sizeof(phandle));
>> +	if (res_mem_count <= 0) {
>> +		dev_warn(dev, "failed to get memory-region property %d\n",
>> +			 res_mem_count);
>> +		return -EINVAL;
>> +	}
>> +
>> +	r5_core->res_mem = devm_kzalloc(dev,
>> +					res_mem_count * sizeof(struct reserved_mem),
>> +					GFP_KERNEL);
>> +	if (!r5_core->res_mem) {
>> +		dev_err(dev, "failed to allocate mem region memory\n");
>> +		return -ENOMEM;
>> +	}
>> +
>> +	for (i = 0; i < res_mem_count; i++) {
>> +		rmem_np = of_parse_phandle(np, "memory-region", i);
>> +		if (!rmem_np)
>> +			return -EINVAL;
>> +
>> +		rmem = of_reserved_mem_lookup(rmem_np);
>> +		if (!rmem) {
>> +			of_node_put(rmem_np);
>> +			return -EINVAL;
>> +		}
>> +
>> +		memcpy(&r5_core->res_mem[i], rmem,
>> +		       sizeof(struct reserved_mem));
>> +		of_node_put(rmem_np);
>> +	}
>> +
>> +	r5_core->res_mem_count = res_mem_count;
>> +
>> +	return 0;
>> +}
>> +
>> +static int zynqmp_r5_core_init(struct zynqmp_r5_cluster *cluster)
>> +{
>> +	int ret, i;
>> +	struct zynqmp_r5_core *r5_core;
>> +	struct device *dev = cluster->dev;
>> +
>> +	ret = zynqmp_r5_get_tcm_node(cluster);
>> +	if (ret < 0) {
>> +		dev_err(dev, "can't get tcm node, err %d\n", ret);
>> +		return ret;
>> +	}
>> +
>> +	for (i = 0; i < cluster->core_count; i++) {
>> +		r5_core = &cluster->r5_cores[i];
>> +		if (!r5_core) {
>> +			pr_err("invalid r5 core\n");
>> +			return -EINVAL;
>> +		}
>> +
>> +		ret = zynqmp_r5_get_mem_region_node(r5_core);
>> +		if (ret)
>> +			dev_warn(dev, "memory-region prop failed %d\n", ret);
>> +
>> +		ret = of_property_read_u32_index(r5_core->np, "power-domains",
>> +						 1, &r5_core->pm_domain_id);
>> +		if (ret) {
>> +			dev_err(dev, "failed to get power-domains property\n");
>> +			return ret;
>> +		}
>> +
>> +		ret = zynqmp_r5_set_mode(r5_core, cluster->mode);
>> +		if (ret)
>> +			return ret;
>> +
>> +		ret = zynqmp_r5_add_rproc_core(r5_core);
>> +		if (ret) {
>> +			dev_err(dev, "failed to init r5 core %d\n", i);
>> +			return ret;
>> +		}
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +static int zynqmp_r5_cluster_init(struct zynqmp_r5_cluster *cluster)
>> +{
>> +	struct device *dev = cluster->dev;
>> +	struct device_node *dev_node = dev_of_node(dev);
>> +	struct device_node *child;
>> +	struct platform_device *child_pdev;
>> +	int core_count = 0, ret, i;
>> +	enum zynqmp_r5_cluster_mode cluster_mode = LOCKSTEP_MODE;
>> +	struct zynqmp_r5_core *r5_cores;
>> +
>> +	ret = of_property_read_u32(dev_node, "xlnx,cluster-mode", &cluster_mode);
>> +
>> +	/* on success returns 0, if not defined then returns -EINVAL,
>> +	 * In that case, default is LOCKSTEP mode
>> +	 */
>> +	if (ret != -EINVAL && ret != 0) {
>> +		dev_err(dev, "Invalid xlnx,cluster-mode property\n");
>> +		return -EINVAL;
>> +	}
>> +
>> +	if (cluster_mode == SINGLE_CPU_MODE) {
>> +		dev_err(dev, "driver does not support single cpu mode\n");
>> +		return -EINVAL;
>> +	} else if ((cluster_mode != SPLIT_MODE &&
>> +		   cluster_mode != LOCKSTEP_MODE)) {
>> +		dev_err(dev, "Invalid cluster mode\n");
>> +		return -EINVAL;
>> +	}
>> +
>> +	core_count = of_get_available_child_count(dev_node);
>> +	if (core_count <= 0) {
>> +		dev_err(dev, "Invalid number of r5 cores %d", core_count);
>> +		return -EINVAL;
>> +	} else if (cluster_mode == SPLIT_MODE && core_count != 2) {
>> +		dev_err(dev, "Invalid number of r5 cores for split mode\n");
>> +		return -EINVAL;
>> +	} else if (cluster_mode == LOCKSTEP_MODE && core_count == 2) {
>> +		dev_warn(dev, "Only r5 core0 will be used\n");
>> +		core_count = 1;
>> +	}
>> +
>> +	r5_cores = devm_kzalloc(dev, sizeof(struct zynqmp_r5_core) *
>> +						 core_count, GFP_KERNEL);
>> +	if (IS_ERR_OR_NULL(r5_cores)) {
>> +		dev_err(dev, "can't allocate memory for cores\n");
>> +		return -ENOMEM;
>> +	}
>> +
>> +	i = 0;
>> +	for_each_available_child_of_node(dev_node, child) {
>> +		child_pdev = of_find_device_by_node(child);
>> +		if (!child_pdev)
>> +			return -ENODEV;
>> +
>> +		r5_cores[i].dev = &child_pdev->dev;
>> +		if (!r5_cores[i].dev) {
>> +			pr_err("can't get device for r5 core %d\n", i);
>> +			return -ENODEV;
>> +		}
>> +
>> +		r5_cores[i].np = dev_of_node(r5_cores[i].dev);
>> +		if (!r5_cores[i].np) {
>> +			pr_err("can't get device node for r5 core %d\n", i);
>> +			return -ENODEV;
>> +		}
>> +
>> +		i++;
>> +		if (i == core_count)
>> +			break;
>> +	}
>> +
>> +	cluster->mode = cluster_mode;
>> +	cluster->core_count = core_count;
>> +	cluster->r5_cores = r5_cores;
>> +
>> +	ret = zynqmp_r5_core_init(cluster);
>> +	if (ret < 0) {
>> +		dev_err(dev, "failed to init r5 core err %d\n", ret);
>> +		return ret;
>> +	}
>> +
>> +	zynqmp_r5_print_dt_node_info(cluster);
>> +
>> +	return 0;
>> +}
>> +
>> +static void zynqmp_r5_cluster_exit(void *data)
>> +{
>> +	struct platform_device *pdev = (struct platform_device *)data;
>> +
>> +	platform_set_drvdata(pdev, NULL);
>> +
>> +	pr_info("Exit r5f subsystem driver\n");
>> +}
>> +
>> +/*
>> + * zynqmp_r5_remoteproc_probe()
>> + *
>> + * @pdev: domain platform device for R5 cluster
>> + *
>> + * called when driver is probed, for each R5 core specified in DT,
>> + * setup as needed to do remoteproc-related operations
>> + *
>> + * Return: 0 for success, negative value for failure.
>> + */
>> +static int zynqmp_r5_remoteproc_probe(struct platform_device *pdev)
>> +{
>> +	int ret;
>> +	struct zynqmp_r5_cluster *cluster;
>> +	struct device *dev = &pdev->dev;
>> +
>> +	cluster = devm_kzalloc(dev, sizeof(*cluster), GFP_KERNEL);
>> +	if (IS_ERR_OR_NULL(cluster))
>> +		return -ENOMEM;
> Function devm_kzalloc() does not return an code on error, just NULL.  Please fix
> throughout the driver.
>
>> +
>> +	cluster->dev = dev;
>> +
>> +	ret = devm_of_platform_populate(dev);
>> +	if (ret) {
>> +		dev_err(dev, "failed to populate platform dev %d\n", ret);
>> +		return ret;
>> +	}
>> +
>> +	/* wire in so each core can be cleaned up at driver remove */
>> +	platform_set_drvdata(pdev, cluster);
>> +
>> +	ret = devm_add_action_or_reset(dev, zynqmp_r5_cluster_exit, pdev);
>> +	if (ret)
>> +		return ret;
>> +
>> +	ret = zynqmp_r5_cluster_init(cluster);
>> +	if (ret) {
>> +		dev_err(dev, "Invalid r5f subsystem device tree\n");
>> +		return ret;
>> +	}
>> +
>> +	dev_info(dev, "Xilinx r5f remoteproc driver probe success\n");
> Please remove this.
>
> I am out of time for today and will continue on Monday.
>
> Thanks,
> Mathieu
>
>> +	return 0;
>> +}
>> +
>> +/* Match table for OF platform binding */
>> +static const struct of_device_id zynqmp_r5_remoteproc_match[] = {
>> +	{ .compatible = "xlnx,zynqmp-r5fss", },
>> +	{ /* end of list */ },
>> +};
>> +MODULE_DEVICE_TABLE(of, zynqmp_r5_remoteproc_match);
>> +
>> +static struct platform_driver zynqmp_r5_remoteproc_driver = {
>> +	.probe = zynqmp_r5_remoteproc_probe,
>> +	.driver = {
>> +		.name = "zynqmp_r5_remoteproc",
>> +		.of_match_table = zynqmp_r5_remoteproc_match,
>> +	},
>> +};
>> +module_platform_driver(zynqmp_r5_remoteproc_driver);
>> +
>> +MODULE_DESCRIPTION("Xilinx R5F remote processor driver");
>> +MODULE_AUTHOR("Xilinx Inc.");
>> +MODULE_LICENSE("GPL v2");
>> -- 
>> 2.25.1
>>

Powered by blists - more mailing lists