linux-kernel - [PATCH 5.15 098/177] ixgbe: set X550 MDIO speed before talking to PHY

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <20211220143043.391512800@linuxfoundation.org>
Date:   Mon, 20 Dec 2021 15:34:08 +0100
From:   Greg Kroah-Hartman <gregkh@...uxfoundation.org>
To:     linux-kernel@...r.kernel.org
Cc:     Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
        stable@...r.kernel.org, Cyril Novikov <cnovikov@...x.com>,
        Andrew Lunn <andrew@...n.ch>,
        Tony Nguyen <anthony.l.nguyen@...el.com>,
        Sasha Levin <sashal@...nel.org>
Subject: [PATCH 5.15 098/177] ixgbe: set X550 MDIO speed before talking to PHY

From: Cyril Novikov <cnovikov@...x.com>

[ Upstream commit bf0a375055bd1afbbf02a0ef45f7655da7b71317 ]

The MDIO bus speed must be initialized before talking to the PHY the first
time in order to avoid talking to it using a speed that the PHY doesn't
support.

This fixes HW initialization error -17 (IXGBE_ERR_PHY_ADDR_INVALID) on
Denverton CPUs (a.k.a. the Atom C3000 family) on ports with a 10Gb network
plugged in. On those devices, HLREG0[MDCSPD] resets to 1, which combined
with the 10Gb network results in a 24MHz MDIO speed, which is apparently
too fast for the connected PHY. PHY register reads over MDIO bus return
garbage, leading to initialization failure.

Reproduced with Linux kernel 4.19 and 5.15-rc7. Can be reproduced using
the following setup:

* Use an Atom C3000 family system with at least one X552 LAN on the SoC
* Disable PXE or other BIOS network initialization if possible
  (the interface must not be initialized before Linux boots)
* Connect a live 10Gb Ethernet cable to an X550 port
* Power cycle (not reset, doesn't always work) the system and boot Linux
* Observe: ixgbe interfaces w/ 10GbE cables plugged in fail with error -17

Fixes: e84db7272798 ("ixgbe: Introduce function to control MDIO speed")
Signed-off-by: Cyril Novikov <cnovikov@...x.com>
Reviewed-by: Andrew Lunn <andrew@...n.ch>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@...el.com>
Signed-off-by: Sasha Levin <sashal@...nel.org>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
index 9724ffb165189..e4b50c7781ffa 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
@@ -3405,6 +3405,9 @@ static s32 ixgbe_reset_hw_X550em(struct ixgbe_hw *hw)
 	/* flush pending Tx transactions */
 	ixgbe_clear_tx_pending(hw);
 
+	/* set MDIO speed before talking to the PHY in case it's the 1st time */
+	ixgbe_set_mdio_speed(hw);
+
 	/* PHY ops must be identified and initialized prior to reset */
 	status = hw->phy.ops.init(hw);
 	if (status == IXGBE_ERR_SFP_NOT_SUPPORTED ||
-- 
2.33.0