Message-Id: <20220103074731.3651-3-avolmat@me.com>
Date:   Mon,  3 Jan 2022 08:47:28 +0100
From:   Alain Volmat <avolmat@...com>
To:     Rob Herring <robh+dt@...nel.org>, linux-pci@...r.kernel.org
Cc:     Patrice Chotard <patrice.chotard@...s.st.com>,
        linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
        Fabrice Gasnier <fabrice.gasnier@...s.st.com>, avolmat@...com
Subject: [PATCH RESEND v2 2/5] pci: dwc: pcie-st: Add PCIe driver for STi platforms

Addition of the PCIe driver (supporting RC) for controllers
found on some STi platforms such as STiH407, STiH410 or
STiH418.
The controller is based on the designware PCIe controller.

Signed-off-by: Alain Volmat <avolmat@...com>
---
v2: update of the pcie-st driver to add possibility to build as module
    and remove the __init of the probe

 drivers/pci/controller/dwc/Kconfig    |  11 +
 drivers/pci/controller/dwc/Makefile   |   1 +
 drivers/pci/controller/dwc/pcie-sti.c | 386 ++++++++++++++++++++++++++
 3 files changed, 398 insertions(+)
 create mode 100644 drivers/pci/controller/dwc/pcie-sti.c

diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
index 62ce3abf0f19..232b8ffd54af 100644
--- a/drivers/pci/controller/dwc/Kconfig
+++ b/drivers/pci/controller/dwc/Kconfig
@@ -384,4 +384,15 @@ config PCIE_FU740
 	  Say Y here if you want PCIe controller support for the SiFive
 	  FU740.
 
+config PCIE_STI
+	tristate "STMicroelectronics PCIe Controller for STi SoCs"
+	depends on ARCH_STI || COMPILE_TEST
+	depends on OF && PCI_MSI_IRQ_DOMAIN
+	select PCIE_DW_HOST
+	help
+	  Enable PCIe controller support on STMicroelectronics STi SoCs.
+	  This controller is based on Designware hardware and therefore
+	  the driver re-uses the Designware core functions to implement
+	  the driver.
+
 endmenu
diff --git a/drivers/pci/controller/dwc/Makefile b/drivers/pci/controller/dwc/Makefile
index 8ba7b67f5e50..c98fa18714ce 100644
--- a/drivers/pci/controller/dwc/Makefile
+++ b/drivers/pci/controller/dwc/Makefile
@@ -21,6 +21,7 @@ obj-$(CONFIG_PCIE_KEEMBAY) += pcie-keembay.o
 obj-$(CONFIG_PCIE_KIRIN) += pcie-kirin.o
 obj-$(CONFIG_PCIE_HISI_STB) += pcie-histb.o
 obj-$(CONFIG_PCI_MESON) += pci-meson.o
+obj-$(CONFIG_PCIE_STI) += pcie-sti.o
 obj-$(CONFIG_PCIE_TEGRA194) += pcie-tegra194.o
 obj-$(CONFIG_PCIE_UNIPHIER) += pcie-uniphier.o
 obj-$(CONFIG_PCIE_UNIPHIER_EP) += pcie-uniphier-ep.o
diff --git a/drivers/pci/controller/dwc/pcie-sti.c b/drivers/pci/controller/dwc/pcie-sti.c
new file mode 100644
index 000000000000..61da00a079ac
--- /dev/null
+++ b/drivers/pci/controller/dwc/pcie-sti.c
@@ -0,0 +1,386 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2021 STMicroelectronics
+ *
+ * STMicroelectronics PCI express Driver for STi SoCs.
+ * ST PCIe IPs are built around a Synopsys IP Core.
+ *
+ * Authors: Fabrice Gasnier <fabrice.gasnier@...s.st.com>
+ *          Alain Volmat <avolmat@...com>
+ */
+
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_gpio.h>
+#include <linux/of_pci.h>
+#include <linux/of_platform.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#include "pcie-designware.h"
+
+/* RC_ADDRESS_TRANSLATION Registers */
+#define TRANSLATION_CONTROL		0x900
+/* Controls if area is inclusive or exclusive */
+#define RC_PASS_ADDR_RANGE		BIT(1)
+
+/* Base of area reserved for config accesses. Fixed size of 64K. */
+#define CFG_BASE_ADDRESS		0x92c
+#define CFG_REGION_SIZE			65536
+#define CFG_SPACE1_OFFSET		0x1000
+
+/* First 4K of config space has this BDF (bus,device,function) */
+#define FUNC0_BDF_NUM			0x930
+
+/* Mem regions */
+#define IN0_MEM_ADDR_START		0x964
+#define IN0_MEM_ADDR_LIMIT		0x968
+#define IN1_MEM_ADDR_START		0x974
+#define IN1_MEM_ADDR_LIMIT		0x978
+
+/* syscfg1 bits */
+#define PCIE_APP_LTSSM_ENABLE		BIT(2)
+/* syscfg0 bits */
+#define PCIE_TYPE_ROOT_COMPLEX		BIT(0)
+
+/* st,syscfg offsets */
+#define SYSCFG0_REG	1
+#define SYSCFG1_REG	2
+
+#define to_st_pcie(x)	dev_get_drvdata((x)->dev)
+
+/**
+ * struct st_pcie - private data of the controller
+ * @dw: designware pcie
+ * @syscfg0: PCIe conf register setting root complex, regmap offset
+ * @syscfg1: PCIe conf register for PCIE_APP_LTSSM_ENABLE, regmap offset
+ * @phy: associated pcie phy
+ * @lmi: memory made available to the controller
+ * @regmap: Syscfg registers bank in which PCIe port is configured
+ * @pwr: power control
+ * @rst: reset control
+ * @reset_gpio: optional reset gpio
+ * @config_window_start: start address of 64K config space area
+ */
+struct st_pcie {
+	struct dw_pcie *dw;
+	int syscfg0;
+	int syscfg1;
+	struct phy *phy;
+	struct resource	*lmi;
+	struct regmap *regmap;
+	struct reset_control *pwr;
+	struct reset_control *rst;
+	struct gpio_desc *reset_gpio;
+	phys_addr_t config_window_start;
+};
+
+/*
+ * The PCI express core IP expects the following arrangement on it's address
+ * bus (slv_haddr) when driving config cycles.
+ * bus_number		[31:24]
+ * dev_number		[23:19]
+ * func_number		[18:16]
+ * unused		[15:12]
+ * ext_reg_number	[11:8]
+ * reg_number		[7:2]
+ *
+ * Bits [15:12] are unused.
+ *
+ * In the glue logic there is a 64K region of address space that can be
+ * written/read to generate config cycles. The base address of this is
+ * controlled by CFG_BASE_ADDRESS. There are 8 16 bit registers called
+ * FUNC0_BDF_NUM to FUNC8_BDF_NUM. These split the bottom half of the 64K
+ * window into 8 regions at 4K boundaries. These control the bus, device and
+ * function number you are trying to talk to.
+ *
+ * The decision on whether to generate a type 0 or type 1 access is controlled
+ * by bits 15:12 of the address you write to.  If they are zero, then a type 0
+ * is generated, if anything else it will be a type 1. Thus the bottom 4K
+ * region controlled by FUNC0_BDF_NUM can only generate type 0, all the others
+ * can only generate type 1.
+ *
+ * We only use FUNC0_BDF_NUM and FUNC1_BDF_NUM. Which one you use is selected
+ * by bit 12 of the address you write to. The selected register is then used
+ * for the top 16 bits of the slv_haddr to form the bus/dev/func, bit 15:12 are
+ * wired to zero, and bits 11:2 form the address of the register you want to
+ * read in config space.
+ *
+ * We always write FUNC0_BDF_NUM as a 32 bit write. So if we want type 1
+ * accesses we have to shift by 16 so in effect we are writing to FUNC1_BDF_NUM
+ */
+static inline u32 bdf_num(int bus, int devfn, int is_root_bus)
+{
+	return ((bus << 8) | devfn) << (is_root_bus ? 0 : 16);
+}
+
+static void __iomem *st_pcie_other_map_bus(struct pci_bus *bus, unsigned int devfn, int where)
+{
+	struct pcie_port *pp = bus->sysdata;
+	struct dw_pcie *dw = to_dw_pcie_from_pp(pp);
+	u32 bdf;
+
+	bdf = bdf_num(bus->number, devfn, pci_is_root_bus(bus));
+
+	/* Set the config packet devfn */
+	dw_pcie_writel_dbi(dw, FUNC0_BDF_NUM, bdf);
+	dw_pcie_readl_dbi(dw, FUNC0_BDF_NUM);
+
+	return pp->va_cfg0_base + where + (pci_is_root_bus(bus->parent) ? 0 : CFG_SPACE1_OFFSET);
+}
+
+static struct pci_ops st_child_pcie_ops = {
+	.map_bus = st_pcie_other_map_bus,
+	.read = pci_generic_config_read,
+	.write = pci_generic_config_write,
+};
+
+static void st_pcie_hw_setup(struct dw_pcie *dw)
+{
+	struct st_pcie *pcie = to_st_pcie(dw);
+
+	/* Set up the config window to the top of the PCI address space */
+	dw_pcie_writel_dbi(dw, CFG_BASE_ADDRESS, pcie->config_window_start);
+
+	/*
+	 * Open up memory to the PCI controller. We could do slightly
+	 * better than this and exclude the kernel text segment and bss etc.
+	 * They are base/limit registers so can be of arbitrary alignment
+	 * presumably
+	 */
+	dw_pcie_writel_dbi(dw, IN0_MEM_ADDR_START, pcie->lmi->start);
+	dw_pcie_writel_dbi(dw, IN0_MEM_ADDR_LIMIT, pcie->lmi->end);
+
+	/* Disable the 2nd region */
+	dw_pcie_writel_dbi(dw, IN1_MEM_ADDR_START, ~0);
+	dw_pcie_writel_dbi(dw, IN1_MEM_ADDR_LIMIT, 0);
+
+	dw_pcie_writel_dbi(dw, TRANSLATION_CONTROL, RC_PASS_ADDR_RANGE);
+}
+
+static int st_pcie_init(struct pcie_port *pp)
+{
+	struct dw_pcie *dw = to_dw_pcie_from_pp(pp);
+	struct st_pcie *pcie = to_st_pcie(dw);
+	int ret;
+
+	/* Set device type : Root Complex */
+	ret = regmap_write(pcie->regmap, pcie->syscfg0, PCIE_TYPE_ROOT_COMPLEX);
+	if (ret < 0) {
+		dev_err(dw->dev, "unable to set device type\n");
+		return ret;
+	}
+
+	ret = reset_control_deassert(pcie->pwr);
+	if (ret) {
+		dev_err(dw->dev, "unable to bring out of powerdown\n");
+		return ret;
+	}
+
+	ret = reset_control_deassert(pcie->rst);
+	if (ret) {
+		dev_err(dw->dev, "unable to bring out of softreset\n");
+		return ret;
+	}
+
+	/* let the controller initialize in the proper mode (RC) after reset */
+	usleep_range(1000, 2000);
+
+	return ret;
+}
+
+static int st_pcie_control_ltssm(struct dw_pcie *dw, bool enable)
+{
+	struct st_pcie *pcie = to_st_pcie(dw);
+
+	return regmap_update_bits(pcie->regmap, pcie->syscfg1, PCIE_APP_LTSSM_ENABLE,
+				  FIELD_PREP(PCIE_APP_LTSSM_ENABLE, enable));
+}
+
+static int st_pcie_host_init(struct pcie_port *pp)
+{
+	struct dw_pcie *dw = to_dw_pcie_from_pp(pp);
+	struct st_pcie *pcie = to_st_pcie(dw);
+	int err;
+
+	pcie->config_window_start = pp->cfg0_base;
+
+	/*
+	 * "Override" default ops provided by designware driver as STI
+	 * PCIe uses its own translation unit rather than iATU
+	 */
+	pp->bridge->child_ops = &st_child_pcie_ops;
+
+	/*
+	 * We have to initialise the PCIe cell on some hardware before we can
+	 * talk to the phy
+	 */
+	err = st_pcie_init(pp);
+	if (err)
+		return err;
+
+	err = st_pcie_control_ltssm(dw, false);
+	if (err) {
+		dev_err(dw->dev, "disable ltssm failed, %d\n", err);
+		return err;
+	}
+
+	/* Init the associated miphy */
+	err = phy_init(pcie->phy);
+	if (err < 0) {
+		dev_err(dw->dev, "Cannot init PHY: %d\n", err);
+		return err;
+	}
+
+	return 0;
+}
+
+static int st_pcie_start_link(struct dw_pcie *dw)
+{
+	struct st_pcie *pcie = to_st_pcie(dw);
+	int err;
+
+	/* Do all the register poking */
+	st_pcie_hw_setup(dw);
+
+	if (pcie->reset_gpio) {
+		/* Assert the PERST# signal */
+		gpiod_set_value(pcie->reset_gpio, 1);
+
+		/* PERST# signal must stay asserted for at least 100us (Tperst-clk) */
+		usleep_range(100, 200);
+
+		/* Release PERST# signal */
+		gpiod_set_value(pcie->reset_gpio, 0);
+	}
+
+	/* Re-enable the link, link training must begin shortly after reset */
+	err = st_pcie_control_ltssm(dw, true);
+	if (err) {
+		dev_err(dw->dev, "enable ltssm failed, %d\n", err);
+		return err;
+	}
+
+	err = dw_pcie_wait_for_link(dw);
+	if (err) {
+		dev_err(dw->dev, "wait for link failed, %d\n", err);
+		return err;
+	}
+
+	/*
+	 * PCIe specification states that you should not issue any config
+	 * requests until 100ms after asserting reset, so we enforce that here
+	 */
+	if  (pcie->reset_gpio)
+		msleep(100);
+
+	return 0;
+}
+
+static struct dw_pcie_host_ops st_pcie_host_ops = {
+	.host_init = st_pcie_host_init,
+};
+
+static const struct dw_pcie_ops dw_pcie_ops = {
+	.start_link = st_pcie_start_link,
+};
+
+static int st_pcie_probe(struct platform_device *pdev)
+{
+	struct st_pcie *pcie;
+	struct dw_pcie *dw;
+	struct device_node *np = pdev->dev.of_node;
+	struct pcie_port *pp;
+	int ret;
+
+	pcie = devm_kzalloc(&pdev->dev, sizeof(*pcie), GFP_KERNEL);
+	if (!pcie)
+		return -ENOMEM;
+
+	dw = devm_kzalloc(&pdev->dev, sizeof(*dw), GFP_KERNEL);
+	if (!dw)
+		return -ENOMEM;
+	pcie->dw = dw;
+	dw->dev = &pdev->dev;
+	dw->ops = &dw_pcie_ops;
+
+	pp = &dw->pp;
+	pp->ops = &st_pcie_host_ops;
+
+	/* mem regions */
+	pcie->lmi = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mem-window");
+	if (!pcie->lmi)
+		return -ENXIO;
+
+	/* regmap registers for PCIe IP configuration */
+	pcie->regmap = syscon_regmap_lookup_by_phandle(np, "st,syscfg");
+	if (IS_ERR(pcie->regmap))
+		return dev_err_probe(&pdev->dev, PTR_ERR(pcie->regmap),
+				     "No syscfg phandle specified\n");
+
+	ret = of_property_read_u32_index(np, "st,syscfg", SYSCFG0_REG, &pcie->syscfg0);
+	if (ret) {
+		dev_err(&pdev->dev, "can't get syscfg0 offset (%d)\n", ret);
+		return ret;
+	}
+
+	ret = of_property_read_u32_index(np, "st,syscfg", SYSCFG1_REG, &pcie->syscfg1);
+	if (ret) {
+		dev_err(&pdev->dev, "can't get syscfg1 offset (%d)\n", ret);
+		return ret;
+	}
+
+	/* powerdown / resets */
+	pcie->pwr = devm_reset_control_get_optional(&pdev->dev, "powerdown");
+	if (IS_ERR(pcie->pwr))
+		return dev_err_probe(&pdev->dev, PTR_ERR(pcie->pwr),
+				     "Error getting powerdown reset control\n");
+
+	pcie->rst = devm_reset_control_get(&pdev->dev, "softreset");
+	if (IS_ERR(pcie->rst))
+		return dev_err_probe(&pdev->dev, PTR_ERR(pcie->rst),
+				     "Error getting softreset control\n");
+
+	/* phy */
+	pcie->phy = devm_phy_get(&pdev->dev, "pcie");
+	if (IS_ERR(pcie->phy))
+		return dev_err_probe(&pdev->dev, PTR_ERR(pcie->phy), "no PHY configured\n");
+
+	/* Claim the GPIO for PRST# if available, keep it de-asserted */
+	pcie->reset_gpio = devm_gpiod_get_optional(&pdev->dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(pcie->reset_gpio))
+		return dev_err_probe(&pdev->dev, PTR_ERR(pcie->reset_gpio),
+				     "Cannot request reset-gpios\n");
+
+	platform_set_drvdata(pdev, pcie);
+
+	ret = dw_pcie_host_init(pp);
+	if (ret)
+		return dev_err_probe(&pdev->dev, ret, "failed to initialize host\n");
+
+	return 0;
+}
+
+static const struct of_device_id st_pcie_of_match[] = {
+	{ .compatible = "st,stih407-pcie", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, st_pcie_of_match);
+
+static struct platform_driver st_pcie_driver __refdata = {
+	.probe  = st_pcie_probe,
+	.driver = {
+		.name = "st-pcie",
+		.of_match_table = st_pcie_of_match,
+	},
+};
+module_platform_driver(st_pcie_driver);
+
+MODULE_AUTHOR("Fabrice Gasnier <fabrice.gasnier@...s.st.com>");
+MODULE_AUTHOR("Alain Volmat <avolmat@...com>");
+MODULE_DESCRIPTION("STi PCIe Controller driver");
+MODULE_LICENSE("GPL v2");
-- 
2.25.1

Powered by blists - more mailing lists