linux-kernel - net: phy: marvell: network working with generic PHY and not with marvell PHY

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [thread-next>] [day] [month] [year] [list]

Date:   Tue, 4 Jan 2022 11:58:01 +0100
From:   Corentin Labbe <clabbe.montjoie@...il.com>
To:     linus.walleij@...aro.org, ulli.kroll@...glemail.com,
        kuba@...nel.org, davem@...emloft.net, andrew@...n.ch,
        hkallweit1@...il.com, linux@...linux.org.uk
Cc:     linux-arm-kernel@...ts.infradead.org, netdev@...r.kernel.org,
        linux-kernel@...r.kernel.org
Subject: net: phy: marvell: network working with generic PHY and not with
 marvell PHY

Hello

I have a gemini SSI 1328 box which has a cortina ethernet MAC with a Marvell 88E1118 as given by:
Marvell 88E1118 gpio-0:01: attached PHY driver (mii_bus:phy_addr=gpio-0:01, irq=POLL)
So booting with CONFIG_MARVELL_PHY=y lead to a non-working network with link set at 1Gbit
Setting 'max-speed = <100>;' (as current state in mainline dtb) lead to a working network.
By not working, I mean kernel started with ip=dhcp cannot get an IP.

Without CONFIG_MARVELL_PHY, the PHY is detected as generic:
Generic PHY gpio-0:01: attached PHY driver (mii_bus:phy_addr=gpio-0:01, irq=POLL)
but with a 1Gbit link, network is now working.
I am able to get an IP via DHCP and iperf give:
Test Complete. Summary Results:
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.04  sec   185 MBytes   154 Mbits/sec    2             sender
[  5]   0.00-10.09  sec   185 MBytes   154 Mbits/sec                  receiver
CPU Utilization: local/sender 77.8% (0.5%u/77.2%s), remote/receiver 13.3% (0.6%u/12.7%s)

ethtool confirms the gigabit link:
Settings for eth0:
	Supported ports: [ TP MII ]
	Supported link modes:   10baseT/Half 10baseT/Full 
	                        100baseT/Half 100baseT/Full 
	                        1000baseT/Half 1000baseT/Full 
	Supported pause frame use: Symmetric Receive-only
	Supports auto-negotiation: Yes
	Supported FEC modes: Not reported
	Advertised link modes:  10baseT/Half 10baseT/Full 
	                        100baseT/Half 100baseT/Full 
	                        1000baseT/Half 1000baseT/Full 
	Advertised pause frame use: Symmetric Receive-only
	Advertised auto-negotiation: Yes
	Advertised FEC modes: Not reported
	Link partner advertised link modes:  10baseT/Half 10baseT/Full 
	                                     100baseT/Half 100baseT/Full 
	                                     1000baseT/Full 
	Link partner advertised pause frame use: No
	Link partner advertised auto-negotiation: Yes
	Link partner advertised FEC modes: Not reported
	Speed: 1000Mb/s
	Duplex: Full
	Port: MII
	PHYAD: 1
	Transceiver: external
	Auto-negotiation: on
	Current message level: 0x00000007 (7)
			       drv probe link
	Link detected: yes

With the marvell PHY, ethtool reports:
Settings for eth0:
	Supported ports: [ TP MII ]
	Supported link modes:   10baseT/Half 10baseT/Full 
	                        100baseT/Half 100baseT/Full 
	                        1000baseT/Half 1000baseT/Full 
	Supported pause frame use: Symmetric Receive-only
	Supports auto-negotiation: Yes
	Supported FEC modes: Not reported
	Advertised link modes:  10baseT/Half 10baseT/Full 
	                        100baseT/Half 100baseT/Full 
	                        1000baseT/Half 1000baseT/Full 
	Advertised pause frame use: Symmetric Receive-only
	Advertised auto-negotiation: Yes
	Advertised FEC modes: Not reported
	Link partner advertised link modes:  10baseT/Half 10baseT/Full 
	                                     100baseT/Half 100baseT/Full 
	                                     1000baseT/Full 
	Link partner advertised pause frame use: No
	Link partner advertised auto-negotiation: Yes
	Link partner advertised FEC modes: Not reported
	Speed: 1000Mb/s
	Duplex: Full
	Port: Twisted Pair
	PHYAD: 1
	Transceiver: external
	Auto-negotiation: on
	MDI-X: Unknown
	Current message level: 0x00000007 (7)
			       drv probe link
	Link detected: yes
Only change vs generic I saw is MDI-X and Port: values

Do you have any idea why the marvell PHY "break" the network ?

Regards