| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <ba055ee6-9d81-3088-f395-8e4e1d9ba136@loongson.cn>
Date: Wed, 5 Jan 2022 11:33:52 +0800
From: zhuyinbo <zhuyinbo@...ngson.cn>
To: "Russell King (Oracle)" <linux@...linux.org.uk>,
Andrew Lunn <andrew@...n.ch>, davem@...emloft.net,
kuba@...nel.org, masahiroy@...nel.org, michal.lkml@...kovi.net,
ndesaulniers@...gle.com
Cc: hkallweit1@...il.com, davem@...emloft.net, kuba@...nel.org,
masahiroy@...nel.org, michal.lkml@...kovi.net,
ndesaulniers@...gle.com, netdev@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-kbuild@...r.kernel.org,
zhuyinbo@...ngson.cn, netdev@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-kbuild@...r.kernel.org
Subject: Re: [PATCH v2 1/2] modpost: file2alias: fixup mdio alias garbled code
in modules.alias
在 2022/1/4 下午9:11, zhuyinbo 写道:
>
>
> 在 2021/12/7 下午5:41, zhuyinbo 写道:
>>
>>
>> 在 2021/12/1 上午8:38, Andrew Lunn 写道:
>>>> However, this won't work for PHY devices created _before_ the kernel
>>>> has mounted the rootfs, whether or not they end up being used. So,
>>>> every PHY mentioned in DT will be created before the rootfs is mounted,
>>>> and none of these PHYs will have their modules loaded.
>>>
>>> Hi Russell
>>>
>>> I think what you are saying here is, if the MAC or MDIO bus driver is
>>> built in, the PHY driver also needs to be built in?
>>>
>>> If the MAC or MDIO bus driver is a module, it means the rootfs has
>>> already been mounted in order to get these modules. And so the PHY
>>> driver as a module will also work.
>>>
>>>> I believe this is the root cause of Yinbo Zhu's issue.
>>
>> I think you should be right and I had did lots of test but use
>> rquest_module it doesn't load marvell module, and dts does't include
>> any phy node. even though I was use "marvell" as input's args of
>> request_module.
>>>
>>> You are speculating that in Yinbo Zhu case, the MAC driver is built
>>> in, the PHY is a module. The initial request for the firmware fails.
>>> Yinbo Zhu would like udev to try again later when the modules are
>>> available.
>>>
>>>> What we _could_ do is review all device trees and PHY drivers to see
>>>> whether DT modaliases are ever used for module loading. If they aren't,
>>>> then we _could_ make the modalias published by the kernel conditional
>>>> on the type of mdio device - continue with the DT approach for non-PHY
>>>> devices, and switch to the mdio: scheme for PHY devices. I repeat, this
>>>> can only happen if no PHY drivers match using the DT scheme, otherwise
>>>> making this change _will_ cause a regression.
>>>
>>
>>> Take a look at
>>> drivers/net/mdio/of_mdio.c:whitelist_phys[] and the comment above it.
>>>
>>> So there are some DT blobs out there with compatible strings for
>>> PHYs. I've no idea if they actually load that way, or the standard PHY
>>> mechanism is used.
>>>
>>> Andrew
>>>
>>
>>
>> > That is not true universally for all MDIO though - as
>> > xilinx_gmii2rgmii.c clearly shows. That is a MDIO driver which uses DT
>> > the compatible string to do the module load. So, we have proof there
>> > that Yinbo Zhu's change will definitely cause a regression which we
>> > can not allow.
>>
>> I don't understand that what you said about regression. My patch
>> doesn't cause xilinx_gmii2rgmii.c driver load fail, in this time that
>> do_of_table and platform_uevent will be responsible "of" type driver
>> auto load and my patch was responsible for "mdio" type driver auto load,
>> In default code. There are request_module to load phy driver, but as
>> Russell King said that request_module doesn't garantee auto load will
>> always work well, but udev mechanism can garantee it. and udev
>> mechaism is more mainstream, otherwise mdio_uevent is useless. if use
>> udev mechanism that my patch was needed. and if apply my patch it
>> doesn't cause request_module mechaism work bad because I will add
>> following change:
>>
>>
>>
>> - ret = request_module(MDIO_MODULE_PREFIX MDIO_ID_FMT,
>> - MDIO_ID_ARGS(phy_id));
>> + ret = request_module(MDIO_MODULE_PREFIX MDIO_ID_FMT, phy_id);
>> /* We only check for failures in executing the usermode binary,
>> * not whether a PHY driver module exists for the PHY ID.
>> * Accept -ENOENT because this may occur in case no initramfs
>> exists,
>> diff --git a/include/linux/mod_devicetable.h
>> b/include/linux/mod_devicetable.h
>> index 7bd23bf..bc6ea0d 100644
>> --- a/include/linux/mod_devicetable.h
>> +++ b/include/linux/mod_devicetable.h
>> @@ -600,16 +600,7 @@ struct platform_device_id {
>> #define MDIO_NAME_SIZE 32
>> #define MDIO_MODULE_PREFIX "mdio:"
>>
>> -#define MDIO_ID_FMT
>> "%u%u%u%u%u%u%u%u%u%u%u%u%u%u%u%u%u%u%u%u%u%u%u%u%u%u%u%u%u%u%u%u"
>> -#define MDIO_ID_ARGS(_id) \
>> - ((_id)>>31) & 1, ((_id)>>30) & 1, ((_id)>>29) & 1, ((_id)>>28)
>> & 1, \
>> - ((_id)>>27) & 1, ((_id)>>26) & 1, ((_id)>>25) & 1, ((_id)>>24)
>> & 1, \
>> - ((_id)>>23) & 1, ((_id)>>22) & 1, ((_id)>>21) & 1, ((_id)>>20)
>> & 1, \
>> - ((_id)>>19) & 1, ((_id)>>18) & 1, ((_id)>>17) & 1, ((_id)>>16)
>> & 1, \
>> - ((_id)>>15) & 1, ((_id)>>14) & 1, ((_id)>>13) & 1, ((_id)>>12)
>> & 1, \
>> - ((_id)>>11) & 1, ((_id)>>10) & 1, ((_id)>>9) & 1, ((_id)>>8) &
>> 1, \
>> - ((_id)>>7) & 1, ((_id)>>6) & 1, ((_id)>>5) & 1, ((_id)>>4) & 1, \
>> - ((_id)>>3) & 1, ((_id)>>2) & 1, ((_id)>>1) & 1, (_id) & 1
>> +#define MDIO_ID_FMT "p%08x"
>>
>>
>>
>
> > > > > However, this won't work for PHY devices created _before_ the
> kernel
> > > > > has mounted the rootfs, whether or not they end up being used. So,
> > > > > every PHY mentioned in DT will be created before the rootfs is
> mounted,
> > > > > and none of these PHYs will have their modules loaded.
> > > >
> > > > Hi Russell
> > > >
> > > > I think what you are saying here is, if the MAC or MDIO bus
> driver is
> > > > built in, the PHY driver also needs to be built in?
> > > >
> > > > If the MAC or MDIO bus driver is a module, it means the rootfs has
> > > > already been mounted in order to get these modules. And so the PHY
> > > > driver as a module will also work.
> > > >
> > > > > I believe this is the root cause of Yinbo Zhu's issue.
> > >
> > > I think you should be right and I had did lots of test but use
> rquest_module
> > > it doesn't load marvell module, and dts does't include any phy
> node. even
> > > though I was use "marvell" as input's args of request_module.
>
> > Please can you report the contents of /proc/sys/kernel/modprobe, and
> > the kernel configuration of CONFIG_MODPROBE_PATH. I wonder if your
> > userspace has that module loading mechanism disabled, or your kernel
> > has CONFIG_MODPROBE_PATH as an empty string.
>
> > If the module is not present by the time this call is made, then
> > even if you load the appropriate driver module later, that module
> > will not be used - the PHY will end up being driven by the generic
> > clause 22 driver.
>
> > > > That is not true universally for all MDIO though - as
> > > > xilinx_gmii2rgmii.c clearly shows. That is a MDIO driver which
> uses DT
> > > > the compatible string to do the module load. So, we have proof there
> > > > that Yinbo Zhu's change will definitely cause a regression which we
> > > > can not allow.
> > >
> > > I don't understand that what you said about regression. My patch
> doesn't
> > > cause xilinx_gmii2rgmii.c driver load fail, in this time that
> do_of_table
> > >and platform_uevent will be responsible "of" type driver auto load
> and my
> > > patch was responsible for "mdio" type driver auto load,
>
> > xilinx_gmii2rgmii is not a platform driver. It is a mdio driver:
>
> > static struct mdio_driver xgmiitorgmii_driver = {
> ^^^^^^^^^^^
>
> > Therefore, platform_uevent() is irrelevant since this will never match
> > a platform device. It will only match mdio devices, and the uevent
> > generation for that is via mdio_uevent() which is the function you
> > are changing.
>
>
> static const struct of_device_id xgmiitorgmii_of_match[] = {
> { .compatible = "xlnx,gmii-to-rgmii-1.0" },
> {},
> };
> MODULE_DEVICE_TABLE(of, xgmiitorgmii_of_match);
>
> static struct mdio_driver xgmiitorgmii_driver = {
> .probe = xgmiitorgmii_probe,
> .mdiodrv.driver = {
> .name = "xgmiitorgmii",
> .of_match_table = xgmiitorgmii_of_match,
> },
> };
> From the present point of view, no matter what the situation, my
> supplement can cover udev or request_module for auto load module.
>
> if that phy driver isn't platform driver my patch cover it I think there
> is no doubt, if phy driver is platform driver and platform driver udev
> will cover it. My only requestion is the request_module not work well.
>
> about xgmiitorgmii_of_match that it belongs to platform driver load,
> please you note. and about your doubt usepace whether disable module
> load that module load function is okay becuase other device driver auto
> load is okay.
>
> > > In default code. There are request_module to load phy driver, but
> as > Russell
> > > King said that request_module doesn't garantee auto load will
> always work
> > > well, but udev mechanism can garantee it. and udev mechaism is more
> > > mainstream, otherwise mdio_uevent is useless. if use udev mechanism
> that my
> > > patch was needed. and if apply my patch it doesn't cause
> request_module
> > > mechaism work bad because I will add following change:
>
> > Please report back what the following command produces on your
> > problem system:
>
> > /sbin/modprobe -vn mdio:00000001010000010000110111010001
>
> > Thanks.
>
> [root@...alhost ~]# lsmod | grep marvell
> [root@...alhost ~]# ls
> /lib/modules/4.19.190+/kernel/drivers/net/phy/marvell.ko
> /lib/modules/4.19.190+/kernel/drivers/net/phy/marvell.ko
> [root@...alhost ~]# /sbin/modprobe -vn
> mdio:00000001010000010000110111010001
> insmod /lib/modules/4.19.190+/kernel/drivers/net/phy/marvell.ko
> insmod /lib/modules/4.19.190+/kernel/drivers/net/phy/marvell.ko
> [root@...alhost ~]#
> [root@...alhost ~]# cat /proc/sys/kernel/modprobe
> /sbin/modprobe
>
> BRs,
> Yinbo
> On Tue, Jan 04, 2022 at 09:11:56PM +0800, zhuyinbo wrote:
> > From the present point of view, no matter what the situation, my
supplement
> > can cover udev or request_module for auto load module.
> >
> > if that phy driver isn't platform driver my patch cover it I think
there is
> > no doubt, if phy driver is platform driver and platform driver udev
will
> > cover it. My only requestion is the request_module not work well.
> >
> > about xgmiitorgmii_of_match that it belongs to platform driver
load, please
> > you note. and about your doubt usepace whether disable module load that
> > module load function is okay becuase other device driver auto load
is okay.
> xgmiitorgmii is *not* a platform driver.
For the module loading function, you need to focus on the first args
"of" in function MODULE_ DEVICE_TABLE, not the definition type of this
driver. for "of" type that must platform covert it !
> > > Please report back what the following command produces on your
> > > problem system:
> > >
> > > /sbin/modprobe -vn mdio:00000001010000010000110111010001
> > >
> > > Thanks.
> >
> > [root@...alhost ~]# lsmod | grep marvell
> > [root@...alhost ~]# ls
> > /lib/modules/4.19.190+/kernel/drivers/net/phy/marvell.ko
> > /lib/modules/4.19.190+/kernel/drivers/net/phy/marvell.ko
> > [root@...alhost ~]# /sbin/modprobe -vn
>mdio:00000001010000010000110111010001
> > insmod /lib/modules/4.19.190+/kernel/drivers/net/phy/marvell.ko
> > insmod /lib/modules/4.19.190+/kernel/drivers/net/phy/marvell.ko
> > [root@...alhost ~]#
> > [root@...alhost ~]# cat /proc/sys/kernel/modprobe
> > /sbin/modprobe
> Great, so the current scheme using "mdio:<binary digits>" works
> perfectly for you. What is missing is having that modalias in the
> uevent file.
No, "lsmod | grep marvel" is NULL, so "mdio:<binary digits>" doesn't
work well. and that lost information is string that match do_mdio_entry
Hexadecimal string or binary digits and I add my patch use hexadecimal
and change do_mdio_entry to fix issue was to consider that different
"Revision Number" represent that phy hardware may be has some
difference, so I think we should not blindly load the corresponding PHY
driver. It is appropriate to match the PHY ID exactly. for
example,following code is marvell phy for 88e1510, which include it's
initial function for phy. and my platform hardware use 88e1512, if
doesn't change do_mdio_entry code, use "?" to match it, which represent
88e1512 hardware to match 881510 driver. of course if 88e1510 driver can
compatible with 88e1512 phy, it is okay, but for all kinds of ethernet
phy hc and hcd you can ensure it always has a good compatible for that?
Like 88e1510 driver, it is compatible with 88e1512 and has no problem.
In fact, I'm not sure if there is a problem with the 88e1512 loaded
88e1510 driver. So I modified do_mdio_entry is used for full matching,
and it can cover above all issue.
.phy_id = MARVELL_PHY_ID_88E1510,
.phy_id_mask = MARVELL_PHY_ID_MASK,
.name = "Marvell 88E1510",
.features = PHY_GBIT_FEATURES | SUPPORTED_FIBRE,
.flags = PHY_HAS_INTERRUPT,
.probe = &m88e1510_probe,
.config_init = &m88e1510_config_init,
.config_aneg = &m88e1510_config_aneg,
.read_status = &marvell_read_status,
> So, my patch on the 4th December should cause the marvell module to
> be loaded at boot time. Please test that patch ASAP, which I have
> already asked you to do. I'll include it again in this email so you
> don't have to hunt for it.
> 8<===
> From: "Russell King (Oracle)" <rmk+kernel@...linux.org.uk>
> Subject: [PATCH] net: phy: generate PHY mdio modalias
> The modalias string provided in the uevent sysfs file does not conform
> to the format used in PHY driver modules. One of the reasons is that
> udev loading of PHY driver modules has not been an expected use case.
> This patch changes the MODALIAS entry for only PHY devices from:
> MODALIAS=of:Nethernet-phyT(null)
> to:
> MODALIAS=mdio:00000000001000100001010100010011
> Other MDIO devices (such as DSA) remain as before.
> However, having udev automatically load the module has the advantage
> of making use of existing functionality to have the module loaded
> before the device is bound to the driver, thus taking advantage of
> multithreaded boot systems, potentially decreasing the boot time.
> However, this patch will not solve any issues with the driver module
> not being loaded prior to the network device needing to use the PHY.
> This is something that is completely out of control of any patch to
> change the uevent mechanism.
> Reported-by: Yinbo Zhu <zhuyinbo@...ngson.cn>
> Signed-off-by: Russell King (Oracle) <rmk+kernel@...linux.org.uk>
> ---
> drivers/net/phy/mdio_bus.c | 8 ++++++++
> drivers/net/phy/phy_device.c | 14 ++++++++++++++
> include/linux/mdio.h | 2 ++
> 3 files changed, 24 insertions(+)
> diff --git a/drivers/net/phy/mdio_bus.c b/drivers/net/phy/mdio_bus.c
> index 4638d7375943..663bd98760fb 100644
> --- a/drivers/net/phy/mdio_bus.c
> +++ b/drivers/net/phy/mdio_bus.c
> @@ -1010,8 +1010,16 @@ static int mdio_bus_match(struct device *dev,
> > struct device_driver *drv)
> static int mdio_uevent(struct device *dev, struct kobj_uevent_env *env)
> {
> + struct mdio_device *mdio = to_mdio_device(dev);
> int rc;
>
> + /* Use the device-specific uevent if specified */
> + if (mdio->bus_uevent) {
> + rc = mdio->bus_uevent(mdio, env);
> + if (rc != -ENODEV)
> + return rc;
> + }
> +
> /* Some devices have extra OF data and an OF-style MODALIAS */
> rc = of_device_uevent_modalias(dev, env);
> if (rc != -ENODEV)
> diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
> index 23667658b9c6..f4c2057f0202 100644
> --- a/drivers/net/phy/phy_device.c
> +++ b/drivers/net/phy/phy_device.c
> @@ -563,6 +563,19 @@ static int phy_request_driver_module(struct
phy_device *dev, u32 phy_id)
> return 0;
> }
> +static int phy_bus_uevent(struct mdio_device *mdiodev,
> + struct kobj_uevent_env *env)
> +{
> + struct phy_device *phydev;
> +
> + phydev = container_of(mdiodev, struct phy_device, mdio);
> +
> + add_uevent_var(env, "MODALIAS=" MDIO_MODULE_PREFIX MDIO_ID_FMT,
> + MDIO_ID_ARGS(phydev->phy_id));
> +
> + return 0;
> +}
> +
> struct phy_device *phy_device_create(struct mii_bus *bus, int addr,
u32 phy_id,
> bool is_c45,
> struct phy_c45_device_ids *c45_ids)
> @@ -582,6 +595,7 @@ struct phy_device *phy_device_create(struct
mii_bus *bus, int addr, u32 phy_id,
> mdiodev->dev.type = &mdio_bus_phy_type;
> mdiodev->bus = bus;
> mdiodev->bus_match = phy_bus_match;
> + mdiodev->bus_uevent = phy_bus_uevent;
> mdiodev->addr = addr;
> mdiodev->flags = MDIO_DEVICE_FLAG_PHY;
> mdiodev->device_free = phy_mdio_device_free;
> diff --git a/include/linux/mdio.h b/include/linux/mdio.h
> index df9c96e56907..5c6676d3de23 100644
> --- a/include/linux/mdio.h
> +++ b/include/linux/mdio.h
> @@ -38,6 +38,8 @@ struct mdio_device {
> char modalias[MDIO_NAME_SIZE];
> int (*bus_match)(struct device *dev, struct device_driver *drv);
> + int (*bus_uevent)(struct mdio_device *mdiodev,
> + struct kobj_uevent_env *env);
> void (*device_free)(struct mdio_device *mdiodev);
> void (*device_remove)(struct mdio_device *mdiodev);
your patch I have a try and it can make marvel driver auto-load.
However, you need to evaluate the above compatibility issues !
in addition, if phy id register work bad or other case, you dont' read
phy id from phy. your patch will not work well. so you shoud definition
a any_phy_id, of course, The most critical issue is the above driver
compatibility, please you note.
in additon, I have never received your email before. I have to check
patchwork every time, so if you have a advice that could you send a mail
to zhuyinbo@...ngson.cn .
Thanks,
BRs,
Yinbo Zhu.
Powered by blists - more mailing lists