[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <CAGOxZ51cEZ2SV=GYdjFEFFhKqp0+KxWcmA0VJx7C1z=UdFqW=Q@mail.gmail.com>
Date: Fri, 7 Jan 2022 00:14:42 +0530
From: Alim Akhtar <alim.akhtar@...il.com>
To: Krzysztof Kozlowski <krzysztof.kozlowski@...onical.com>
Cc: Tomasz Figa <tomasz.figa@...il.com>,
Sylwester Nawrocki <s.nawrocki@...sung.com>,
Linus Walleij <linus.walleij@...aro.org>,
Rob Herring <robh+dt@...nel.org>,
linux-arm-kernel@...ts.infradead.org,
linux-samsung-soc@...r.kernel.org, linux-gpio@...r.kernel.org,
devicetree@...r.kernel.org,
open list <linux-kernel@...r.kernel.org>,
Marek Szyprowski <m.szyprowski@...sung.com>,
Sylwester Nawrocki <snawrocki@...nel.org>,
Sam Protsenko <semen.protsenko@...aro.org>,
Chanho Park <chanho61.park@...sung.com>
Subject: Re: [PATCH 07/24] ARM: dts: exynos: override pins by label in Peach Pi
Hi Krzysztof,
On Sat, Jan 1, 2022 at 1:15 PM Krzysztof Kozlowski
<krzysztof.kozlowski@...onical.com> wrote:
>
> Using node paths to extend or override a device tree node is error
> prone. If there was a typo error, a new node will be created instead of
> extending the existing node. This will lead to run-time errors that
> could be hard to detect.
>
> A mistyped label on the other hand, will cause a dtc compile error
> (during build time).
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@...onical.com>
> ---
Reviewed-by: Alim Akhtar <alim.akhtar@...sung.com>
> arch/arm/boot/dts/exynos5800-peach-pi.dts | 33 +++++++++++------------
> 1 file changed, 16 insertions(+), 17 deletions(-)
>
> diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts
> index 77013ee586f8..6bf3fd37fb2b 100644
> --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts
> +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts
> @@ -850,27 +850,26 @@ pmic_dvs_1: pmic-dvs-1 {
> };
> };
>
> -&pinctrl_1 {
> - /* Adjust WiFi drive strengths lower for EMI */
> - sd1_clk: sd1-clk {
> - samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
> - };
> +/* pinctrl_1 */
> +/* Adjust WiFi drive strengths lower for EMI */
> +&sd1_bus1 {
> + samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
> +};
>
> - sd1_cmd: sd1-cmd {
> - samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
> - };
> +&sd1_bus4 {
> + samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
> +};
>
> - sd1_bus1: sd1-bus-width1 {
> - samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
> - };
> +&sd1_bus8 {
> + samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
> +};
>
> - sd1_bus4: sd1-bus-width4 {
> - samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
> - };
> +&sd1_clk {
> + samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
> +};
>
> - sd1_bus8: sd1-bus-width8 {
> - samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
> - };
> +&sd1_cmd {
> + samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
> };
>
> &pinctrl_2 {
> --
> 2.32.0
>
--
Regards,
Alim
Powered by blists - more mailing lists