| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <24759eaf-ede6-32e4-a673-cba3659d4ad3@canonical.com>
Date: Tue, 11 Jan 2022 17:28:57 +0100
From: Krzysztof Kozlowski <krzysztof.kozlowski@...onical.com>
To: Rob Herring <robh@...nel.org>
Cc: Chanwoo Choi <cw00.choi@...sung.com>,
Bartlomiej Zolnierkiewicz <b.zolnierkie@...sung.com>,
Pavel Machek <pavel@....cz>, Lee Jones <lee.jones@...aro.org>,
Sebastian Reichel <sre@...nel.org>,
Liam Girdwood <lgirdwood@...il.com>,
Mark Brown <broonie@...nel.org>, linux-kernel@...r.kernel.org,
linux-leds@...r.kernel.org, devicetree@...r.kernel.org,
linux-pm@...r.kernel.org
Subject: Re: [PATCH 4/4] dt-bindings: mfd: maxim,max77693: convert to dtschema
On 10/01/2022 20:10, Rob Herring wrote:
> On Tue, Dec 28, 2021 at 05:39:30PM +0100, Krzysztof Kozlowski wrote:
>> Convert the MFD part of Maxim MAX77693 MUIC to DT schema format. The
>> example DTS was copied from existing DTS (exynos4412-midas.dtsi), so
>> keep the license as GPL-2.0-only.
>>
>> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@...onical.com>
>> ---
>> .../devicetree/bindings/mfd/max77693.txt | 194 ------------------
>> .../bindings/mfd/maxim,max77693.yaml | 139 +++++++++++++
>> MAINTAINERS | 2 +-
>> 3 files changed, 140 insertions(+), 195 deletions(-)
>> delete mode 100644 Documentation/devicetree/bindings/mfd/max77693.txt
>> create mode 100644 Documentation/devicetree/bindings/mfd/maxim,max77693.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt
>> deleted file mode 100644
>> index 1032df14498b..000000000000
>> --- a/Documentation/devicetree/bindings/mfd/max77693.txt
>> +++ /dev/null
>> @@ -1,194 +0,0 @@
>> -Maxim MAX77693 multi-function device
>> -
>> -MAX77693 is a Multifunction device with the following submodules:
>> -- PMIC,
>> -- CHARGER,
>> -- LED,
>> -- MUIC,
>> -- HAPTIC
>> -
>> -It is interfaced to host controller using i2c.
>> -This document describes the bindings for the mfd device.
>> -
>> -Required properties:
>> -- compatible : Must be "maxim,max77693".
>> -- reg : Specifies the i2c slave address of PMIC block.
>> -- interrupts : This i2c device has an IRQ line connected to the main SoC.
>> -
>> -Optional properties:
>> -- regulators : The regulators of max77693 have to be instantiated under subnode
>> - named "regulators" using the following format.
>> -
>> - regulators {
>> - regulator-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER
>> - standard regulator constraints[*].
>> - };
>> -
>> - [*] refer Documentation/devicetree/bindings/regulator/regulator.txt
>> -
>> -- haptic : The MAX77693 haptic device utilises a PWM controlled motor to provide
>> - users with tactile feedback. PWM period and duty-cycle are varied in
>> - order to provide the appropriate level of feedback.
>> -
>> - Required properties:
>> - - compatible : Must be "maxim,max77693-haptic"
>> - - haptic-supply : power supply for the haptic motor
>> - [*] refer Documentation/devicetree/bindings/regulator/regulator.txt
>> - - pwms : phandle to the physical PWM(Pulse Width Modulation) device.
>> - PWM properties should be named "pwms". And number of cell is different
>> - for each pwm device.
>> - To get more information, please refer to documentation.
>> - [*] refer Documentation/devicetree/bindings/pwm/pwm.txt
>> -
>> -- charger : Node configuring the charger driver.
>> - If present, required properties:
>> - - compatible : Must be "maxim,max77693-charger".
>> -
>> - Optional properties (if not set, defaults will be used):
>> - - maxim,constant-microvolt : Battery constant voltage in uV. The charger
>> - will operate in fast charge constant current mode till battery voltage
>> - reaches this level. Then the charger will switch to fast charge constant
>> - voltage mode. Also vsys (system voltage) will be set to this value when
>> - DC power is supplied but charger is not enabled.
>> - Valid values: 3650000 - 4400000, step by 25000 (rounded down)
>> - Default: 4200000
>> -
>> - - maxim,min-system-microvolt : Minimal system voltage in uV.
>> - Valid values: 3000000 - 3700000, step by 100000 (rounded down)
>> - Default: 3600000
>> -
>> - - maxim,thermal-regulation-celsius : Temperature in Celsius for entering
>> - high temperature charging mode. If die temperature exceeds this value
>> - the charging current will be reduced by 105 mA/Celsius.
>> - Valid values: 70, 85, 100, 115
>> - Default: 100
>> -
>> - - maxim,battery-overcurrent-microamp : Overcurrent protection threshold
>> - in uA (current from battery to system).
>> - Valid values: 2000000 - 3500000, step by 250000 (rounded down)
>> - Default: 3500000
>> -
>> - - maxim,charge-input-threshold-microvolt : Threshold voltage in uV for
>> - triggering input voltage regulation loop. If input voltage decreases
>> - below this value, the input current will be reduced to reach the
>> - threshold voltage.
>> - Valid values: 4300000, 4700000, 4800000, 4900000
>> - Default: 4300000
>> -
>> -- led : the LED submodule device node
>> -
>> -There are two LED outputs available - FLED1 and FLED2. Each of them can
>> -control a separate LED or they can be connected together to double
>> -the maximum current for a single connected LED. One LED is represented
>> -by one child node.
>> -
>> -Required properties:
>> -- compatible : Must be "maxim,max77693-led".
>> -
>> -Optional properties:
>> -- maxim,boost-mode :
>> - In boost mode the device can produce up to 1.2A of total current
>> - on both outputs. The maximum current on each output is reduced
>> - to 625mA then. If not enabled explicitly, boost setting defaults to
>> - LEDS_BOOST_FIXED in case both current sources are used.
>> - Possible values:
>> - LEDS_BOOST_OFF (0) - no boost,
>> - LEDS_BOOST_ADAPTIVE (1) - adaptive mode,
>> - LEDS_BOOST_FIXED (2) - fixed mode.
>> -- maxim,boost-mvout : Output voltage of the boost module in millivolts.
>> - Valid values: 3300 - 5500, step by 25 (rounded down)
>> - Default: 3300
>> -- maxim,mvsys-min : Low input voltage level in millivolts. Flash is not fired
>> - if chip estimates that system voltage could drop below this level due
>> - to flash power consumption.
>> - Valid values: 2400 - 3400, step by 33 (rounded down)
>> - Default: 2400
>> -
>> -Required properties for the LED child node:
>> -- led-sources : see Documentation/devicetree/bindings/leds/common.txt;
>> - device current output identifiers: 0 - FLED1, 1 - FLED2
>> -- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
>> - Valid values for a LED connected to one FLED output:
>> - 15625 - 250000, step by 15625 (rounded down)
>> - Valid values for a LED connected to both FLED outputs:
>> - 15625 - 500000, step by 15625 (rounded down)
>> -- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
>> - Valid values for a single LED connected to one FLED output
>> - (boost mode must be turned off):
>> - 15625 - 1000000, step by 15625 (rounded down)
>> - Valid values for a single LED connected to both FLED outputs:
>> - 15625 - 1250000, step by 15625 (rounded down)
>> - Valid values for two LEDs case:
>> - 15625 - 625000, step by 15625 (rounded down)
>> -- flash-max-timeout-us : see Documentation/devicetree/bindings/leds/common.txt
>> - Valid values: 62500 - 1000000, step by 62500 (rounded down)
>> -
>> -Optional properties for the LED child node:
>> -- label : see Documentation/devicetree/bindings/leds/common.txt
>> -
>> -Optional nodes:
>> -- max77693-muic :
>> - Node used only by extcon consumers.
>> - Required properties:
>> - - compatible : "maxim,max77693-muic"
>> -
>> -Example:
>> -#include <dt-bindings/leds/common.h>
>> -
>> - max77693@66 {
>> - compatible = "maxim,max77693";
>> - reg = <0x66>;
>> - interrupt-parent = <&gpx1>;
>> - interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
>> -
>> - regulators {
>> - esafeout@1 {
>> - regulator-compatible = "ESAFEOUT1";
>> - regulator-name = "ESAFEOUT1";
>> - regulator-boot-on;
>> - };
>> - esafeout@2 {
>> - regulator-compatible = "ESAFEOUT2";
>> - regulator-name = "ESAFEOUT2";
>> - };
>> - charger@0 {
>> - regulator-compatible = "CHARGER";
>> - regulator-name = "CHARGER";
>> - regulator-min-microamp = <60000>;
>> - regulator-max-microamp = <2580000>;
>> - regulator-boot-on;
>> - };
>> - };
>> -
>> - haptic {
>> - compatible = "maxim,max77693-haptic";
>> - haptic-supply = <&haptic_supply>;
>> - pwms = <&pwm 0 40000 0>;
>> - pwm-names = "haptic";
>> - };
>> -
>> - charger {
>> - compatible = "maxim,max77693-charger";
>> -
>> - maxim,constant-microvolt = <4200000>;
>> - maxim,min-system-microvolt = <3600000>;
>> - maxim,thermal-regulation-celsius = <75>;
>> - maxim,battery-overcurrent-microamp = <3000000>;
>> - maxim,charge-input-threshold-microvolt = <4300000>;
>> - };
>> -
>> - led {
>> - compatible = "maxim,max77693-led";
>> - maxim,boost-mode = <LEDS_BOOST_FIXED>;
>> - maxim,boost-mvout = <5000>;
>> - maxim,mvsys-min = <2400>;
>> -
>> - camera_flash: flash-led {
>> - label = "max77693-flash";
>> - led-sources = <0>, <1>;
>> - led-max-microamp = <500000>;
>> - flash-max-microamp = <1250000>;
>> - flash-max-timeout-us = <1000000>;
>> - };
>> - };
>> - };
>> diff --git a/Documentation/devicetree/bindings/mfd/maxim,max77693.yaml b/Documentation/devicetree/bindings/mfd/maxim,max77693.yaml
>> new file mode 100644
>> index 000000000000..bc9c90bd4ff9
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/mfd/maxim,max77693.yaml
>> @@ -0,0 +1,139 @@
>> +# SPDX-License-Identifier: GPL-2.0-only
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/mfd/maxim,max77693.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Maxim MAX77693 MicroUSB and Companion Power Management IC
>> +
>> +maintainers:
>> + - Chanwoo Choi <cw00.choi@...sung.com>
>> + - Krzysztof Kozlowski <krzysztof.kozlowski@...onical.com>
>> +
>> +description: |
>> + This is a part of device tree bindings for Maxim MAX77693 MicroUSB
>> + Integrated Circuit (MUIC).
>> +
>> + The Maxim MAX77693 is a MicroUSB and Companion Power Management IC which
>> + includes voltage current regulators, charger, LED/flash, haptic motor driver
>> + and MicroUSB management IC.
>> +
>> +properties:
>> + compatible:
>> + const: maxim,max77693
>> +
>> + interrupts:
>> + maxItems: 1
>> +
>> + reg:
>> + maxItems: 1
>> +
>> + charger:
>> + $ref: ../power/supply/maxim,max77693.yaml
>
> /schemas/power/supply/...
>
>> +
>> + led:
>> + $ref: ../leds/maxim,max77693.yaml
>
> ditto
>
>> +
>> + max77693-muic:
>> + type: object
>
> additionalProperties: false
>
>> + properties:
>> + compatible:
>> + const: maxim,max77693-muic
>> +
>> + required:
>> + - compatible
>> +
>> + motor-driver:
>> + type: object
>
> additionalProperties: false
>
Thanks, fixed all issues.
Best regards,
Krzysztof
Powered by blists - more mailing lists