| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAA8EJpqVAB31uzav-qMsBEBk0j2dk-qy1cRRRccCRLgJRqCS2g@mail.gmail.com>
Date: Sat, 29 Jan 2022 07:59:30 +0300
From: Dmitry Baryshkov <dmitry.baryshkov@...aro.org>
To: Kuogee Hsieh <quic_khsieh@...cinc.com>
Cc: robdclark@...il.com, sean@...rly.run, swboyd@...omium.org,
vkoul@...nel.org, daniel@...ll.ch, airlied@...ux.ie,
agross@...nel.org, bjorn.andersson@...aro.org,
quic_abhinavk@...cinc.com, aravindh@...eaurora.org,
freedreno@...ts.freedesktop.org, dri-devel@...ts.freedesktop.org,
linux-arm-msm@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH] drm/msm/dp: add wide bus support
Hi,
Thank you for your patch.
On Fri, 28 Jan 2022 at 20:29, Kuogee Hsieh <quic_khsieh@...cinc.com> wrote:
>
> Normally, mdp will push one pixel of data per pixel clock to
> interface to display. Wide bus feature will increase bus
> width from 32 bits to 64 bits so that it can push two
> pixel of data per pixel clock to interface to display.
> This feature is pre requirement to support 4k resolution.
>
> Signed-off-by: Kuogee Hsieh <quic_khsieh@...cinc.com>
> ---
> drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c | 16 ++-
> drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.h | 2 +
> .../gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 14 +++
> drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c | 108 +++++++++++++++------
> drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h | 5 +
> drivers/gpu/drm/msm/dp/dp_catalog.c | 11 ++-
> drivers/gpu/drm/msm/dp/dp_catalog.h | 1 +
> drivers/gpu/drm/msm/dp/dp_ctrl.c | 9 +-
> drivers/gpu/drm/msm/dp/dp_ctrl.h | 1 +
> drivers/gpu/drm/msm/dp/dp_display.c | 17 ++++
> drivers/gpu/drm/msm/dp/dp_display.h | 3 +
> drivers/gpu/drm/msm/dp/dp_parser.c | 26 +++++
> drivers/gpu/drm/msm/dp/dp_parser.h | 2 +
> drivers/gpu/drm/msm/msm_drv.h | 9 ++
Can we get this split into logical chunks please?
> 14 files changed, 190 insertions(+), 34 deletions(-)
>
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
> index 1e648db..e2fb5bc 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
> @@ -199,6 +199,8 @@ struct dpu_encoder_virt {
>
> struct msm_display_info disp_info;
>
> + struct msm_op_info op_info;
> +
> bool idle_pc_supported;
> struct mutex rc_lock;
> enum dpu_enc_rc_states rc_state;
> @@ -217,6 +219,13 @@ static u32 dither_matrix[DITHER_MATRIX_SZ] = {
> 15, 7, 13, 5, 3, 11, 1, 9, 12, 4, 14, 6, 0, 8, 2, 10
> };
>
> +bool dpu_encoder_is_widebus_enabled(struct drm_encoder *drm_enc)
> +{
> + struct dpu_encoder_virt *dpu_enc = to_dpu_encoder_virt(drm_enc);
> +
> + return dpu_enc->op_info.wide_bus_en;
> +}
> +
> static void _dpu_encoder_setup_dither(struct dpu_hw_pingpong *hw_pp, unsigned bpc)
> {
> struct dpu_hw_dither_cfg dither_cfg = { 0 };
> @@ -2112,6 +2121,7 @@ int dpu_encoder_setup(struct drm_device *dev, struct drm_encoder *enc,
> struct dpu_kms *dpu_kms = to_dpu_kms(priv->kms);
> struct drm_encoder *drm_enc = NULL;
> struct dpu_encoder_virt *dpu_enc = NULL;
> + struct msm_op_info *op_info;
> int ret = 0;
>
> dpu_enc = to_dpu_encoder_virt(enc);
> @@ -2128,8 +2138,12 @@ int dpu_encoder_setup(struct drm_device *dev, struct drm_encoder *enc,
> timer_setup(&dpu_enc->vsync_event_timer,
> dpu_encoder_vsync_event_handler,
> 0);
> - else if (disp_info->intf_type == DRM_MODE_ENCODER_TMDS)
> + else if (disp_info->intf_type == DRM_MODE_ENCODER_TMDS) {
> dpu_enc->dp = priv->dp[disp_info->h_tile_instance[0]];
> + op_info = &priv->op_info[disp_info->h_tile_instance[0]];
op_info should be defined per INTF rather than per h_tile. This way
you won't have to check for intf_type here.
> + dpu_enc->op_info = *op_info;
So... we set this data in msm_drm_private only to copy it to
dpu_encoder_virt? Please don't do this.
Allow one to query the data from the DP rather than blindly copying it
over and over again.
> +
> + }
>
> INIT_DELAYED_WORK(&dpu_enc->delayed_off_work,
> dpu_encoder_off_work);
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.h
> index e241914..0d73550 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.h
> @@ -168,4 +168,6 @@ int dpu_encoder_get_linecount(struct drm_encoder *drm_enc);
> */
> int dpu_encoder_get_vsync_count(struct drm_encoder *drm_enc);
>
> +bool dpu_encoder_is_widebus_enabled(struct drm_encoder *drm_enc);
> +
> #endif /* __DPU_ENCODER_H__ */
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> index ddd9d89..04ac2dc 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> @@ -110,6 +110,20 @@ static void drm_mode_to_intf_timing_params(
> timing->v_back_porch += timing->v_front_porch;
> timing->v_front_porch = 0;
> }
> +
> + timing->wide_bus_en = dpu_encoder_is_widebus_enabled(phys_enc->parent);
> +
> + /*
> + * for DP, divide the horizonal parameters by 2 when
> + * widebus is enabled
> + */
> + if (phys_enc->hw_intf->cap->type == INTF_DP && timing->wide_bus_en) {
What about INTF_eDP?
I suspect that intf type check is unnecessary here.
> + timing->width = timing->width >> 1;
> + timing->xres = timing->xres >> 1;
> + timing->h_back_porch = timing->h_back_porch >> 1;
> + timing->h_front_porch = timing->h_front_porch >> 1;
> + timing->hsync_pulse_width = timing->hsync_pulse_width >> 1;
> + }
> }
>
> static u32 get_horizontal_total(const struct intf_timing_params *timing)
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> index 116e2b5..f072bd5 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> @@ -33,6 +33,7 @@
> #define INTF_TP_COLOR1 0x05C
> #define INTF_CONFIG2 0x060
> #define INTF_DISPLAY_DATA_HCTL 0x064
> +#define INTF_ACTIVE_DATA_HCTL 0x068
> #define INTF_FRAME_LINE_COUNT_EN 0x0A8
> #define INTF_FRAME_COUNT 0x0AC
> #define INTF_LINE_COUNT 0x0B0
> @@ -90,67 +91,109 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *ctx,
> u32 hsync_period, vsync_period;
> u32 display_v_start, display_v_end;
> u32 hsync_start_x, hsync_end_x;
> + u32 hsync_data_start_x, hsync_data_end_x;
> u32 active_h_start, active_h_end;
> u32 active_v_start, active_v_end;
> u32 active_hctl, display_hctl, hsync_ctl;
> u32 polarity_ctl, den_polarity, hsync_polarity, vsync_polarity;
> u32 panel_format;
> - u32 intf_cfg, intf_cfg2 = 0, display_data_hctl = 0;
> + u32 intf_cfg, intf_cfg2 = 0;
> + u32 display_data_hctl = 0, active_data_hctl = 0;
> + u32 data_width;
> + bool dp_intf = false;
>
> /* read interface_cfg */
> intf_cfg = DPU_REG_READ(c, INTF_CONFIG);
> +
> + if (ctx->cap->type == INTF_EDP || ctx->cap->type == INTF_DP)
> + dp_intf = true;
> +
> hsync_period = p->hsync_pulse_width + p->h_back_porch + p->width +
> p->h_front_porch;
> vsync_period = p->vsync_pulse_width + p->v_back_porch + p->height +
> p->v_front_porch;
>
> display_v_start = ((p->vsync_pulse_width + p->v_back_porch) *
> - hsync_period) + p->hsync_skew;
> + hsync_period) + p->hsync_skew;
Unnecessary whitespace changes complicate reviewing. I'll try groking
this piece of code later.
> display_v_end = ((vsync_period - p->v_front_porch) * hsync_period) +
> - p->hsync_skew - 1;
> + p->hsync_skew - 1;
> +
> + hsync_ctl = (hsync_period << 16) | p->hsync_pulse_width;
>
> hsync_start_x = p->h_back_porch + p->hsync_pulse_width;
> hsync_end_x = hsync_period - p->h_front_porch - 1;
>
> - if (p->width != p->xres) {
> - active_h_start = hsync_start_x;
> - active_h_end = active_h_start + p->xres - 1;
> - } else {
> - active_h_start = 0;
> - active_h_end = 0;
> - }
> + /*
> + * DATA_HCTL_EN controls data timing which can be different from
> + * video timing. It is recommended to enable it for all cases, except
> + * if compression is enabled in 1 pixel per clock mode
> + */
> + if (!p->compression_en || p->wide_bus_en)
> + intf_cfg2 |= BIT(4);
>
> - if (p->height != p->yres) {
> - active_v_start = display_v_start;
> - active_v_end = active_v_start + (p->yres * hsync_period) - 1;
> - } else {
> - active_v_start = 0;
> - active_v_end = 0;
> - }
> + if (p->wide_bus_en)
> + intf_cfg2 |= BIT(0);
> +
> + /*
> + * If widebus is disabled:
> + * For uncompressed stream, the data is valid for the entire active
> + * window period.
> + * For compressed stream, data is valid for a shorter time period
> + * inside the active window depending on the compression ratio.
> + *
> + * If widebus is enabled:
> + * For uncompressed stream, data is valid for only half the active
> + * window, since the data rate is doubled in this mode.
> + * p->width holds the adjusted width for DP but unadjusted width for DSI
> + * For compressed stream, data validity window needs to be adjusted for
> + * compression ratio and then further halved.
> + */
> + data_width = p->width;
> +
> + if (p->compression_en) {
> + data_width = DIV_ROUND_UP(p->dce_bytes_per_line, 3);
>
> - if (active_h_end) {
> - active_hctl = (active_h_end << 16) | active_h_start;
> - intf_cfg |= BIT(29); /* ACTIVE_H_ENABLE */
> + if (p->wide_bus_en)
> + data_width >>= 1;
> + } else if (!dp_intf && p->wide_bus_en) {
> + data_width = p->width >> 1;
> } else {
> - active_hctl = 0;
> + data_width = p->width;
> }
>
> - if (active_v_end)
> - intf_cfg |= BIT(30); /* ACTIVE_V_ENABLE */
> + hsync_data_start_x = hsync_start_x;
> + hsync_data_end_x = hsync_start_x + data_width - 1;
>
> - hsync_ctl = (hsync_period << 16) | p->hsync_pulse_width;
> display_hctl = (hsync_end_x << 16) | hsync_start_x;
> + display_data_hctl = (hsync_data_end_x << 16) | hsync_data_start_x;
>
> - if (ctx->cap->type == INTF_EDP || ctx->cap->type == INTF_DP) {
> - active_h_start = hsync_start_x;
> - active_h_end = active_h_start + p->xres - 1;
> - active_v_start = display_v_start;
> - active_v_end = active_v_start + (p->yres * hsync_period) - 1;
> -
> + if (dp_intf) {
> + // DP timing adjustment
> display_v_start += p->hsync_pulse_width + p->h_back_porch;
> + display_v_end -= p->h_front_porch;
> + }
>
> - active_hctl = (active_h_end << 16) | active_h_start;
> +
> + active_h_start = hsync_start_x;
> + active_h_end = active_h_start + p->xres - 1;
> +
> + active_v_start = display_v_start;
> + active_v_end = active_v_start + (p->yres * hsync_period) - 1;
> +
> + intf_cfg |= BIT(29); /* ACTIVE_H_ENABLE */
> + intf_cfg |= BIT(30); /* ACTIVE_V_ENABLE */
> +
> + active_hctl = (active_h_end << 16) | active_h_start;
> +
> + if (dp_intf) {
> display_hctl = active_hctl;
> + if (p->compression_en) {
I assume that compression_en is a part of DSC support for the DP, isn't it?
If so, it should definitely come as a separate patch.
> + active_data_hctl = (hsync_start_x +
> + p->extra_dto_cycles) << 16;
> + active_data_hctl += hsync_start_x;
> +
> + display_data_hctl = active_data_hctl;
> + }
> }
>
> den_polarity = 0;
> @@ -204,6 +247,9 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *ctx,
> DPU_REG_WRITE(c, INTF_FRAME_LINE_COUNT_EN, 0x3);
> DPU_REG_WRITE(c, INTF_CONFIG, intf_cfg);
> DPU_REG_WRITE(c, INTF_PANEL_FORMAT, panel_format);
> + DPU_REG_WRITE(c, INTF_CONFIG2, intf_cfg2);
> + DPU_REG_WRITE(c, INTF_DISPLAY_DATA_HCTL, display_data_hctl);
> + DPU_REG_WRITE(c, INTF_ACTIVE_DATA_HCTL, active_data_hctl);
Are these registers present on all supported hardware (like sdm845)?
Does msm8998 support them? msm8996?
> }
>
> static void dpu_hw_intf_enable_timing_engine(
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
> index 3568be8..8fc71ce 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
> @@ -30,6 +30,11 @@ struct intf_timing_params {
> u32 border_clr;
> u32 underflow_clr;
> u32 hsync_skew;
> +
> + bool wide_bus_en;
> + bool compression_en;
> + u32 extra_dto_cycles; /* for DP only */
> + u32 dce_bytes_per_line;
All compression-related items should come in a separate patch.
> };
>
> struct intf_prog_fetch {
> diff --git a/drivers/gpu/drm/msm/dp/dp_catalog.c b/drivers/gpu/drm/msm/dp/dp_catalog.c
> index 6d6850e..d738e2e 100644
> --- a/drivers/gpu/drm/msm/dp/dp_catalog.c
> +++ b/drivers/gpu/drm/msm/dp/dp_catalog.c
> @@ -745,6 +745,7 @@ int dp_catalog_panel_timing_cfg(struct dp_catalog *dp_catalog)
> {
> struct dp_catalog_private *catalog = container_of(dp_catalog,
> struct dp_catalog_private, dp_catalog);
> + u32 reg;
>
> dp_write_link(catalog, REG_DP_TOTAL_HOR_VER,
> dp_catalog->total);
> @@ -753,7 +754,15 @@ int dp_catalog_panel_timing_cfg(struct dp_catalog *dp_catalog)
> dp_write_link(catalog, REG_DP_HSYNC_VSYNC_WIDTH_POLARITY,
> dp_catalog->width_blanking);
> dp_write_link(catalog, REG_DP_ACTIVE_HOR_VER, dp_catalog->dp_active);
> - dp_write_p0(catalog, MMSS_DP_INTF_CONFIG, 0);
> +
> + reg = dp_read_p0(catalog, MMSS_DP_INTF_CONFIG);
> +
> + if (dp_catalog->wide_bus_en)
> + reg |= BIT(4);
> + else
> + reg &= ~BIT(4);
> +
> + dp_write_p0(catalog, MMSS_DP_INTF_CONFIG, reg);
> return 0;
> }
>
> diff --git a/drivers/gpu/drm/msm/dp/dp_catalog.h b/drivers/gpu/drm/msm/dp/dp_catalog.h
> index 7dea101..6ca563f 100644
> --- a/drivers/gpu/drm/msm/dp/dp_catalog.h
> +++ b/drivers/gpu/drm/msm/dp/dp_catalog.h
> @@ -70,6 +70,7 @@ struct dp_catalog {
> enum dp_catalog_audio_sdp_type sdp_type;
> enum dp_catalog_audio_header_type sdp_header;
> u32 audio_data;
> + bool wide_bus_en;
> };
>
> /* Debug module */
> diff --git a/drivers/gpu/drm/msm/dp/dp_ctrl.c b/drivers/gpu/drm/msm/dp/dp_ctrl.c
> index 53ad3af..401ae57 100644
> --- a/drivers/gpu/drm/msm/dp/dp_ctrl.c
> +++ b/drivers/gpu/drm/msm/dp/dp_ctrl.c
> @@ -1812,6 +1812,7 @@ int dp_ctrl_on_stream(struct dp_ctrl *dp_ctrl)
> int ret = 0;
> bool mainlink_ready = false;
> struct dp_ctrl_private *ctrl;
> + u32 pixel_rate_orig;
>
> if (!dp_ctrl)
> return -EINVAL;
> @@ -1820,6 +1821,10 @@ int dp_ctrl_on_stream(struct dp_ctrl *dp_ctrl)
>
> ctrl->dp_ctrl.pixel_rate = ctrl->panel->dp_mode.drm_mode.clock;
>
> + pixel_rate_orig = ctrl->dp_ctrl.pixel_rate;
> + if (dp_ctrl->wide_bus_en)
> + ctrl->dp_ctrl.pixel_rate >>= 1;
> +
> drm_dbg_dp((struct drm_device *)NULL, "rate=%d, num_lanes=%d, pixel_rate=%d\n",
> ctrl->link->link_params.rate,
> ctrl->link->link_params.num_lanes, ctrl->dp_ctrl.pixel_rate);
> @@ -1855,11 +1860,13 @@ int dp_ctrl_on_stream(struct dp_ctrl *dp_ctrl)
> */
> reinit_completion(&ctrl->video_comp);
>
> + ctrl->catalog->wide_bus_en = dp_ctrl->wide_bus_en;
Can you limit the DP's knowledge of wide_bus_en to a single place
(e.g. only in dp_catalog or in dp_ctrl)? Just copying the data bit
means that we have two places which must be kept in sync.
> +
> dp_ctrl_configure_source_params(ctrl);
>
> dp_catalog_ctrl_config_msa(ctrl->catalog,
> ctrl->link->link_params.rate,
> - ctrl->dp_ctrl.pixel_rate, dp_ctrl_use_fixed_nvid(ctrl));
> + pixel_rate_orig, dp_ctrl_use_fixed_nvid(ctrl));
>
> dp_ctrl_setup_tr_unit(ctrl);
>
> diff --git a/drivers/gpu/drm/msm/dp/dp_ctrl.h b/drivers/gpu/drm/msm/dp/dp_ctrl.h
> index 2433edb..4dff44d 100644
> --- a/drivers/gpu/drm/msm/dp/dp_ctrl.h
> +++ b/drivers/gpu/drm/msm/dp/dp_ctrl.h
> @@ -17,6 +17,7 @@ struct dp_ctrl {
> bool orientation;
> atomic_t aborted;
> u32 pixel_rate;
> + bool wide_bus_en;
> };
>
> int dp_ctrl_on_link(struct dp_ctrl *dp_ctrl);
> diff --git a/drivers/gpu/drm/msm/dp/dp_display.c b/drivers/gpu/drm/msm/dp/dp_display.c
> index f89f3ed..924c9e2 100644
> --- a/drivers/gpu/drm/msm/dp/dp_display.c
> +++ b/drivers/gpu/drm/msm/dp/dp_display.c
> @@ -873,6 +873,8 @@ static int dp_display_enable(struct dp_display_private *dp, u32 data)
> return 0;
> }
>
> + dp->ctrl->wide_bus_en = dp_display->wide_bus_en;
Ugh. This adds a third place. dp_display, dp_ctrl and dp_catalog. Too
much for a single bit.
> +
> rc = dp_ctrl_on_stream(dp->ctrl);
> if (!rc)
> dp_display->power_on = true;
> @@ -1004,6 +1006,8 @@ int dp_display_get_modes(struct msm_dp *dp,
> dp->connector, dp_mode);
> if (dp_mode->drm_mode.clock)
> dp->max_pclk_khz = dp_mode->drm_mode.clock;
> +
> + DRM_DEBUG_DP("wide_bus_en=%d\n", dp->wide_bus_en);
> return ret;
> }
>
> @@ -1503,6 +1507,8 @@ int msm_dp_modeset_init(struct msm_dp *dp_display, struct drm_device *dev,
> {
> struct msm_drm_private *priv;
> struct dp_display_private *dp_priv;
> + struct msm_op_info *op;
> + struct dp_display_private *dp;
> int ret;
>
> if (WARN_ON(!encoder) || WARN_ON(!dp_display) || WARN_ON(!dev))
> @@ -1545,6 +1551,17 @@ int msm_dp_modeset_init(struct msm_dp *dp_display, struct drm_device *dev,
>
> priv->bridges[priv->num_bridges++] = dp_display->bridge;
>
> + dp = container_of(dp_display, struct dp_display_private, dp_display);
> +
> + dp_display->wide_bus_en = dp->parser->has_widebus;
> + dp_display->compression_en = dp->parser->has_compression;
> +
> + op = &priv->op_info[dp->id];
> + op->wide_bus_en = dp_display->wide_bus_en;
> + op->compression_en = dp_display->compression_en;
> +
> + drm_dbg_dp(dp->drm_dev, "id=%d widebus=%d compression=%d\n",
> + dp->id, op->wide_bus_en, op->compression_en);
> return 0;
> }
>
> diff --git a/drivers/gpu/drm/msm/dp/dp_display.h b/drivers/gpu/drm/msm/dp/dp_display.h
> index e3adcd5..b1057cb 100644
> --- a/drivers/gpu/drm/msm/dp/dp_display.h
> +++ b/drivers/gpu/drm/msm/dp/dp_display.h
> @@ -24,6 +24,9 @@ struct msm_dp {
>
> hdmi_codec_plugged_cb plugged_cb;
>
> + bool wide_bus_en;
> + bool compression_en;
> +
> u32 max_pclk_khz;
>
> u32 max_dp_lanes;
> diff --git a/drivers/gpu/drm/msm/dp/dp_parser.c b/drivers/gpu/drm/msm/dp/dp_parser.c
> index e74012d..fd48eb8 100644
> --- a/drivers/gpu/drm/msm/dp/dp_parser.c
> +++ b/drivers/gpu/drm/msm/dp/dp_parser.c
> @@ -286,6 +286,28 @@ static int dp_parser_find_panel(struct dp_parser *parser)
> return 0;
> }
>
> +static void dp_parser_compression(struct dp_parser *parser)
> +{
> + struct device *dev = &parser->pdev->dev;
> +
> + parser->has_compression = of_property_read_bool(dev->of_node,
> + "qcom,compression-enable");
> +
> + DRM_DEBUG_DP("compression parsing successful. compression:%d\n",
> + parser->has_compression);
> +}
> +
> +static void dp_parser_widebus(struct dp_parser *parser)
> +{
> + struct device *dev = &parser->pdev->dev;
> +
> + parser->has_widebus = of_property_read_bool(dev->of_node,
> + "qcom,widebus-enable");
> +
> + DRM_DEBUG_DP("widebus parsing successful. widebus:%d\n",
> + parser->has_widebus);
> +}
All new properties should be described in the dt-bindings document.
However I have a bigger question here. Who and how decides whether
compression or widebus should be enabled?
Should we enable widebus for all generations that support it? If so,
this should be a part of msm_dp_config rather than the DTS property.
And I'm completely puzzled about the compression-enable here.
> +
> static int dp_parser_parse(struct dp_parser *parser, int connector_type)
> {
> int rc = 0;
> @@ -319,6 +341,10 @@ static int dp_parser_parse(struct dp_parser *parser, int connector_type)
> */
> parser->regulator_cfg = &sdm845_dp_reg_cfg;
>
> + dp_parser_widebus(parser);
> +
> + dp_parser_compression(parser);
> +
> return 0;
> }
>
> diff --git a/drivers/gpu/drm/msm/dp/dp_parser.h b/drivers/gpu/drm/msm/dp/dp_parser.h
> index 3172da0..7531fe2 100644
> --- a/drivers/gpu/drm/msm/dp/dp_parser.h
> +++ b/drivers/gpu/drm/msm/dp/dp_parser.h
> @@ -123,6 +123,8 @@ struct dp_parser {
> struct dp_display_data disp_data;
> const struct dp_regulator_cfg *regulator_cfg;
> u32 max_dp_lanes;
> + bool has_widebus;
> + bool has_compression;
> struct drm_bridge *panel_bridge;
>
> int (*parse)(struct dp_parser *parser, int connector_type);
> diff --git a/drivers/gpu/drm/msm/msm_drv.h b/drivers/gpu/drm/msm/msm_drv.h
> index d7574e6..1a5f3e9 100644
> --- a/drivers/gpu/drm/msm/msm_drv.h
> +++ b/drivers/gpu/drm/msm/msm_drv.h
> @@ -127,6 +127,11 @@ struct msm_display_info {
> bool is_te_using_watchdog_timer;
> };
>
> +struct msm_op_info {
> + bool wide_bus_en;
> + bool compression_en;
> +};
> +
> /* Commit/Event thread specific structure */
> struct msm_drm_thread {
> struct drm_device *dev;
> @@ -156,6 +161,8 @@ struct msm_drm_private {
>
> struct msm_dp *dp[MSM_DP_CONTROLLER_COUNT];
>
> + struct msm_op_info op_info[MSM_DP_CONTROLLER_COUNT];
> +
As I said before, it should be INTF_MAX. Or you can retrieve it from
priv->dp as needed instead.
> /* when we have more than one 'msm_gpu' these need to be an array: */
> struct msm_gpu *gpu;
>
> @@ -338,6 +345,8 @@ int msm_hdmi_modeset_init(struct hdmi *hdmi, struct drm_device *dev,
> void __init msm_hdmi_register(void);
> void __exit msm_hdmi_unregister(void);
>
> +struct msm_dp;
> +
> struct msm_dsi;
> #ifdef CONFIG_DRM_MSM_DSI
> int dsi_dev_attach(struct platform_device *pdev);
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
>
--
With best wishes
Dmitry
Powered by blists - more mailing lists