linux-kernel - [PATCH v3 5/9] serial: omap: remove redundant code in rs485

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Date:   Tue, 22 Feb 2022 02:14:29 +0100
From:   Lino Sanfilippo <LinoSanfilippo@....de>
To:     gregkh@...uxfoundation.org, jirislaby@...nel.org,
        u.kleine-koenig@...gutronix.de
Cc:     linux@...linux.org.uk, richard.genoud@...il.com,
        nicolas.ferre@...rochip.com, alexandre.belloni@...tlin.com,
        ludovic.desroches@...rochip.com, shawnguo@...nel.org,
        s.hauer@...gutronix.de, kernel@...gutronix.de, festevam@...il.com,
        linux-imx@....com, mcoquelin.stm32@...il.com,
        alexandre.torgue@...s.st.com, linux-serial@...r.kernel.org,
        linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
        linux-stm32@...md-mailman.stormreply.com, lukas@...ner.de,
        p.rosenberger@...bus.com, Lino Sanfilippo <LinoSanfilippo@....de>
Subject: [PATCH v3 5/9] serial: omap: remove redundant code in rs485_config

In uart_set_rs485_config() the serial core already clamps the RTS delays.
It also assigns the passed serial_rs485 struct to the uart port.

So remove these tasks from the drivers rs485_config() function to avoid
redundancy.

Signed-off-by: Lino Sanfilippo <LinoSanfilippo@....de>
---
 drivers/tty/serial/omap-serial.c | 13 +++----------
 1 file changed, 3 insertions(+), 10 deletions(-)

diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
index 0862941862c8..a3afcccfbd96 100644
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -1350,18 +1350,11 @@ serial_omap_config_rs485(struct uart_port *port, struct serial_rs485 *rs485)
 	up->ier = 0;
 	serial_out(up, UART_IER, 0);
 
-	/* Clamp the delays to [0, 100ms] */
-	rs485->delay_rts_before_send = min(rs485->delay_rts_before_send, 100U);
-	rs485->delay_rts_after_send  = min(rs485->delay_rts_after_send, 100U);
-
-	/* store new config */
-	port->rs485 = *rs485;
-
 	if (up->rts_gpiod) {
 		/* enable / disable rts */
-		val = (port->rs485.flags & SER_RS485_ENABLED) ?
+		val = (rs485->flags & SER_RS485_ENABLED) ?
 			SER_RS485_RTS_AFTER_SEND : SER_RS485_RTS_ON_SEND;
-		val = (port->rs485.flags & val) ? 1 : 0;
+		val = (rs485->flags & val) ? 1 : 0;
 		gpiod_set_value(up->rts_gpiod, val);
 	}
 
@@ -1372,7 +1365,7 @@ serial_omap_config_rs485(struct uart_port *port, struct serial_rs485 *rs485)
 	/* If RS-485 is disabled, make sure the THR interrupt is fired when
 	 * TX FIFO is below the trigger level.
 	 */
-	if (!(port->rs485.flags & SER_RS485_ENABLED) &&
+	if (!(rs485->flags & SER_RS485_ENABLED) &&
 	    (up->scr & OMAP_UART_SCR_TX_EMPTY)) {
 		up->scr &= ~OMAP_UART_SCR_TX_EMPTY;
 		serial_out(up, UART_OMAP_SCR, up->scr);
-- 
2.35.1