lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
Open Source and information security mailing list archives
| ||
|
Message-ID: <20220222103848.8530-2-antoniu.miclaus@analog.com> Date: Tue, 22 Feb 2022 12:38:47 +0200 From: Antoniu Miclaus <antoniu.miclaus@...log.com> To: <jic23@...nel.org>, <robh+dt@...nel.org>, <linux-iio@...r.kernel.org>, <devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org> CC: Antoniu Miclaus <antoniu.miclaus@...log.com> Subject: [PATCH v5 2/3] iio: amplifiers: ada4250: add support for ADA4250 The ADA4250 is an instrumentation amplifier with SPI/pin-strap progammable gains that is optimized for ultra-low power systems. With a minimum supply voltage of 1.7V, 26uA of quiescent current, a shutdown mode, a sleep mode, and a fast wake up settling time, ADA4250 can be power cycled on a battery powered system for even futher savings. Signed-off-by: Antoniu Miclaus <antoniu.miclaus@...log.com> --- changes in v5: - add spaces after `:` in commit subject drivers/iio/amplifiers/Kconfig | 11 + drivers/iio/amplifiers/Makefile | 1 + drivers/iio/amplifiers/ada4250.c | 403 +++++++++++++++++++++++++++++++ 3 files changed, 415 insertions(+) create mode 100644 drivers/iio/amplifiers/ada4250.c diff --git a/drivers/iio/amplifiers/Kconfig b/drivers/iio/amplifiers/Kconfig index 5eb1357a9c78..f217a2a1e958 100644 --- a/drivers/iio/amplifiers/Kconfig +++ b/drivers/iio/amplifiers/Kconfig @@ -23,6 +23,17 @@ config AD8366 To compile this driver as a module, choose M here: the module will be called ad8366. +config ADA4250 + tristate "Analog Devices ADA4250 Instrumentation Amplifier" + depends on SPI + help + Say yes here to build support for Analog Devices ADA4250 + SPI Amplifier's support. The driver provides direct access via + sysfs. + + To compile this driver as a module, choose M here: the + module will be called ada4250. + config HMC425 tristate "Analog Devices HMC425A and similar GPIO Gain Amplifiers" depends on GPIOLIB diff --git a/drivers/iio/amplifiers/Makefile b/drivers/iio/amplifiers/Makefile index cb551d82f56b..2126331129cf 100644 --- a/drivers/iio/amplifiers/Makefile +++ b/drivers/iio/amplifiers/Makefile @@ -5,4 +5,5 @@ # When adding new entries keep the list in alphabetical order obj-$(CONFIG_AD8366) += ad8366.o +obj-$(CONFIG_ADA4250) += ada4250.o obj-$(CONFIG_HMC425) += hmc425a.o diff --git a/drivers/iio/amplifiers/ada4250.c b/drivers/iio/amplifiers/ada4250.c new file mode 100644 index 000000000000..4b32d350dc5d --- /dev/null +++ b/drivers/iio/amplifiers/ada4250.c @@ -0,0 +1,403 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * ADA4250 driver + * + * Copyright 2022 Analog Devices Inc. + */ + +#include <linux/bitfield.h> +#include <linux/bits.h> +#include <linux/device.h> +#include <linux/iio/iio.h> +#include <linux/module.h> +#include <linux/regmap.h> +#include <linux/regulator/consumer.h> +#include <linux/spi/spi.h> + +#include <asm/unaligned.h> + +/* ADA4250 Register Map */ +#define ADA4250_REG_GAIN_MUX 0x00 +#define ADA4250_REG_REFBUF_EN 0x01 +#define ADA4250_REG_RESET 0x02 +#define ADA4250_REG_SNSR_CAL_VAL 0x04 +#define ADA4250_REG_SNSR_CAL_CNFG 0x05 +#define ADA4250_REG_DIE_REV 0x18 +#define ADA4250_REG_CHIP_ID 0x19 + +/* ADA4250_REG_GAIN_MUX Map */ +#define ADA4250_GAIN_MUX_MSK GENMASK(2, 0) + +/* ADA4250_REG_REFBUF Map */ +#define ADA4250_REFBUF_MSK BIT(0) + +/* ADA4250_REG_RESET Map */ +#define ADA4250_RESET_MSK BIT(0) + +/* ADA4250_REG_SNSR_CAL_VAL Map */ +#define ADA4250_CAL_CFG_BIAS_MSK GENMASK(7, 0) + +/* ADA4250_REG_SNSR_CAL_CNFG Bit Definition */ +#define ADA4250_BIAS_SET_MSK GENMASK(3, 2) +#define ADA4250_RANGE_SET_MSK GENMASK(1, 0) + +/* Miscellaneous definitions */ +#define ADA4250_CHIP_ID 0x4250 +#define ADA4250_RANGE1 0 +#define ADA4250_RANGE4 3 + +/* ADA4250 current bias set */ +enum ada4250_current_bias { + ADA4250_BIAS_DISABLED, + ADA4250_BIAS_BANDGAP, + ADA4250_BIAS_AVDD, +}; + +struct ada4250_state { + struct spi_device *spi; + struct regmap *regmap; + struct regulator *reg; + /* Protect against concurrent accesses to the device and data content */ + struct mutex lock; + u8 bias; + u8 gain; + int offset_uv; + bool refbuf_en; +}; + +/* ADA4250 Current Bias Source Settings: Disabled, Bandgap Reference, AVDD */ +static const int calibbias_table[] = {0, 1, 2}; + +/* ADA4250 Gain (V/V) values: 1, 2, 4, 8, 16, 32, 64, 128 */ +static const int hwgain_table[] = {1, 2, 4, 8, 16, 32, 64, 128}; + +static const struct regmap_config ada4250_regmap_config = { + .reg_bits = 8, + .val_bits = 8, + .read_flag_mask = BIT(7), + .max_register = 0x1A, +}; + +static int ada4250_set_offset_uv(struct iio_dev *indio_dev, + const struct iio_chan_spec *chan, + int offset_uv) +{ + struct ada4250_state *st = iio_priv(indio_dev); + + int i, ret, x[8], max_vos, min_vos, voltage_v, vlsb = 0; + u8 offset_raw, range = ADA4250_RANGE1; + u32 lsb_coeff[6] = {1333, 2301, 4283, 8289, 16311, 31599}; + + if (st->bias == 0 || st->bias == 3) + return -EINVAL; + + voltage_v = regulator_get_voltage(st->reg); + voltage_v = DIV_ROUND_CLOSEST(voltage_v, 1000000); + + if (st->bias == ADA4250_BIAS_AVDD) + x[0] = voltage_v; + else + x[0] = 5; + + x[1] = 126 * (x[0] - 1); + + for (i = 0; i < 6; i++) + x[i + 2] = DIV_ROUND_CLOSEST(x[1] * 1000, lsb_coeff[i]); + + if (st->gain == 0) + return -EINVAL; + + /* + * Compute Range and Voltage per LSB for the Sensor Offset Calibration + * Example of computation for Range 1 and Range 2 (Curren Bias Set = AVDD): + * Range 1 Range 2 + * Gain | Max Vos(mV) | LSB(mV) | Max Vos(mV) | LSB(mV) | + * 2 | X1*127 | X1=0.126(AVDD-1) | X1*3*127 | X1*3 | + * 4 | X2*127 | X2=X1/1.3333 | X2*3*127 | X2*3 | + * 8 | X3*127 | X3=X1/2.301 | X3*3*127 | X3*3 | + * 16 | X4*127 | X4=X1/4.283 | X4*3*127 | X4*3 | + * 32 | X5*127 | X5=X1/8.289 | X5*3*127 | X5*3 | + * 64 | X6*127 | X6=X1/16.311 | X6*3*127 | X6*3 | + * 128 | X7*127 | X7=X1/31.599 | X7*3*127 | X7*3 | + */ + for (i = ADA4250_RANGE1; i <= ADA4250_RANGE4; i++) { + max_vos = x[st->gain] * 127 * ((1 << (i + 1)) - 1); + min_vos = -1 * max_vos; + if (offset_uv > min_vos && offset_uv < max_vos) { + range = i; + vlsb = x[st->gain] * ((1 << (i + 1)) - 1); + break; + } + } + + if (vlsb <= 0) + return -EINVAL; + + offset_raw = DIV_ROUND_CLOSEST(abs(offset_uv), vlsb); + + mutex_lock(&st->lock); + ret = regmap_update_bits(st->regmap, ADA4250_REG_SNSR_CAL_CNFG, + ADA4250_RANGE_SET_MSK, + FIELD_PREP(ADA4250_RANGE_SET_MSK, range)); + if (ret) + goto exit; + + st->offset_uv = offset_raw * vlsb; + + /* + * To set the offset calibration value, use bits [6:0] and bit 7 as the + * polarity bit (set to "0" for a negative offset and "1" for a positive + * offset). + */ + if (offset_uv < 0) { + offset_raw |= BIT(7); + st->offset_uv *= (-1); + } + + ret = regmap_write(st->regmap, ADA4250_REG_SNSR_CAL_VAL, offset_raw); + +exit: + mutex_unlock(&st->lock); + + return ret; +} + +static int ada4250_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int *val, int *val2, long info) +{ + struct ada4250_state *st = iio_priv(indio_dev); + int ret; + + switch (info) { + case IIO_CHAN_INFO_HARDWAREGAIN: + ret = regmap_read(st->regmap, ADA4250_REG_GAIN_MUX, val); + if (ret) + return ret; + + *val = BIT(*val); + + return IIO_VAL_INT; + case IIO_CHAN_INFO_OFFSET: + *val = st->offset_uv; + + return IIO_VAL_INT; + case IIO_CHAN_INFO_CALIBBIAS: + ret = regmap_read(st->regmap, ADA4250_REG_SNSR_CAL_CNFG, val); + if (ret) + return ret; + + *val = FIELD_GET(ADA4250_BIAS_SET_MSK, *val); + + return IIO_VAL_INT; + case IIO_CHAN_INFO_SCALE: + *val = 1; + *val2 = 1000000; + + return IIO_VAL_FRACTIONAL; + default: + return -EINVAL; + } +} + +static int ada4250_write_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int val, int val2, long info) +{ + struct ada4250_state *st = iio_priv(indio_dev); + int ret; + + switch (info) { + case IIO_CHAN_INFO_HARDWAREGAIN: + ret = regmap_write(st->regmap, ADA4250_REG_GAIN_MUX, + FIELD_PREP(ADA4250_GAIN_MUX_MSK, ilog2(val))); + if (ret) + return ret; + + st->gain = ilog2(val); + + return ret; + case IIO_CHAN_INFO_OFFSET: + return ada4250_set_offset_uv(indio_dev, chan, val); + case IIO_CHAN_INFO_CALIBBIAS: + ret = regmap_update_bits(st->regmap, ADA4250_REG_SNSR_CAL_CNFG, + ADA4250_BIAS_SET_MSK, + FIELD_PREP(ADA4250_BIAS_SET_MSK, val)); + if (ret) + return ret; + + st->bias = val; + + return ret; + default: + return -EINVAL; + } +} + +static int ada4250_read_avail(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + const int **vals, int *type, int *length, + long mask) +{ + switch (mask) { + case IIO_CHAN_INFO_CALIBBIAS: + *vals = calibbias_table; + *type = IIO_VAL_INT; + *length = ARRAY_SIZE(calibbias_table); + + return IIO_AVAIL_LIST; + case IIO_CHAN_INFO_HARDWAREGAIN: + *vals = hwgain_table; + *type = IIO_VAL_INT; + *length = ARRAY_SIZE(hwgain_table); + + return IIO_AVAIL_LIST; + default: + return -EINVAL; + } +} + +static int ada4250_reg_access(struct iio_dev *indio_dev, + unsigned int reg, + unsigned int write_val, + unsigned int *read_val) +{ + struct ada4250_state *st = iio_priv(indio_dev); + + if (read_val) + return regmap_read(st->regmap, reg, read_val); + else + return regmap_write(st->regmap, reg, write_val); +} + +static const struct iio_info ada4250_info = { + .read_raw = ada4250_read_raw, + .write_raw = ada4250_write_raw, + .read_avail = &ada4250_read_avail, + .debugfs_reg_access = &ada4250_reg_access, +}; + +static const struct iio_chan_spec ada4250_channels[] = { + { + .type = IIO_VOLTAGE, + .output = 1, + .indexed = 1, + .channel = 0, + .info_mask_separate = BIT(IIO_CHAN_INFO_HARDWAREGAIN) | + BIT(IIO_CHAN_INFO_OFFSET) | + BIT(IIO_CHAN_INFO_CALIBBIAS) | + BIT(IIO_CHAN_INFO_SCALE), + .info_mask_separate_available = BIT(IIO_CHAN_INFO_CALIBBIAS) | + BIT(IIO_CHAN_INFO_HARDWAREGAIN), + } +}; + +static void ada4250_reg_disable(void *data) +{ + regulator_disable(data); +} + +static int ada4250_init(struct ada4250_state *st) +{ + int ret; + u16 chip_id; + u8 data[2] __aligned(8) = {}; + struct spi_device *spi = st->spi; + + st->refbuf_en = device_property_read_bool(&spi->dev, "adi,refbuf-enable"); + + st->reg = devm_regulator_get(&spi->dev, "avdd"); + if (IS_ERR(st->reg)) + return dev_err_probe(&spi->dev, PTR_ERR(st->reg), + "failed to get the AVDD voltage\n"); + + ret = regulator_enable(st->reg); + if (ret) { + dev_err(&spi->dev, "Failed to enable specified AVDD supply\n"); + return ret; + } + + ret = devm_add_action_or_reset(&spi->dev, ada4250_reg_disable, st->reg); + if (ret) + return ret; + + ret = regmap_write(st->regmap, ADA4250_REG_RESET, + FIELD_PREP(ADA4250_RESET_MSK, 1)); + if (ret) + return ret; + + ret = regmap_bulk_read(st->regmap, ADA4250_REG_CHIP_ID, data, 2); + if (ret) + return ret; + + chip_id = get_unaligned_le16(data); + + if (chip_id != ADA4250_CHIP_ID) { + dev_err(&spi->dev, "Invalid chip ID.\n"); + return -EINVAL; + } + + return regmap_write(st->regmap, ADA4250_REG_REFBUF_EN, + FIELD_PREP(ADA4250_REFBUF_MSK, st->refbuf_en)); +} + +static int ada4250_probe(struct spi_device *spi) +{ + struct iio_dev *indio_dev; + struct regmap *regmap; + struct ada4250_state *st; + int ret; + + indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st)); + if (!indio_dev) + return -ENOMEM; + + regmap = devm_regmap_init_spi(spi, &ada4250_regmap_config); + if (IS_ERR(regmap)) + return PTR_ERR(regmap); + + st = iio_priv(indio_dev); + st->regmap = regmap; + st->spi = spi; + + indio_dev->info = &ada4250_info; + indio_dev->name = "ada4250"; + indio_dev->channels = ada4250_channels; + indio_dev->num_channels = ARRAY_SIZE(ada4250_channels); + + mutex_init(&st->lock); + + ret = ada4250_init(st); + if (ret) { + dev_err(&spi->dev, "ADA4250 init failed\n"); + return ret; + } + + return devm_iio_device_register(&spi->dev, indio_dev); +} + +static const struct spi_device_id ada4250_id[] = { + { "ada4250", 0 }, + {} +}; +MODULE_DEVICE_TABLE(spi, ada4250_id); + +static const struct of_device_id ada4250_of_match[] = { + { .compatible = "adi,ada4250" }, + {}, +}; +MODULE_DEVICE_TABLE(of, ada4250_of_match); + +static struct spi_driver ada4250_driver = { + .driver = { + .name = "ada4250", + .of_match_table = ada4250_of_match, + }, + .probe = ada4250_probe, + .id_table = ada4250_id, +}; +module_spi_driver(ada4250_driver); + +MODULE_AUTHOR("Antoniu Miclaus <antoniu.miclaus@...log.com"); +MODULE_DESCRIPTION("Analog Devices ADA4250"); +MODULE_LICENSE("GPL v2"); -- 2.35.1
Powered by blists - more mailing lists