| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <85566f97-dcfc-f477-1ebb-5cac955b791a@microchip.com>
Date: Thu, 24 Feb 2022 15:51:27 +0100
From: Nicolas Ferre <nicolas.ferre@...rochip.com>
To: Michael Walle <michael@...le.cc>,
Kavyasree Kotagiri <kavyasree.kotagiri@...rochip.com>
CC: <arnd@...db.de>, <alexandre.belloni@...tlin.com>, <olof@...om.net>,
<soc@...nel.org>, <robh+dt@...nel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
<UNGLinuxDriver@...rochip.com>, <Manohar.Puri@...rochip.com>
Subject: Re: [PATCH v7] ARM: dts: add DT for lan966 SoC and 2-port board
pcb8291
Michael,
On 21/02/2022 at 10:10, Michael Walle wrote:
> Am 2022-02-21 09:08, schrieb Kavyasree Kotagiri:
>> This patch adds basic DT for Microchip lan966x SoC and associated board
>> pcb8291(2-port EVB). Adds peripherals required to allow booting:
>> Interrupt
>> Controller, Clock, Generic ARMv7 Timers, Synopsys Timer, Flexcoms,
>> GPIOs.
>> Also adds other peripherals like crypto(AES/SHA), DMA, Watchdog Timer,
>> TRNG
>> and MCAN0.
>>
>> Signed-off-by: Kavyasree Kotagiri <kavyasree.kotagiri@...rochip.com>
>> ---
>> v6 -> v7:
>> - Removed "arm,cpu-registers-not-fw-configured" property, as not
>> required.
>> - Corrected "PPI interrupt cpu mask" and order of interrupts.
>>
>> v5 -> v6:
>> - Renamed dts file to lan966x-pcb8291.dts file.
>> - Disabled optional watchdog in dtsi file and enabled it in dts file.
>>
>> v4 -> v5:
>> - Modified AES, SHA, TRNG node names as per generic names recommended.
>>
>> v3 -> v4:
>> - Removed character 'x' from compatible string.
>> - Removed memory node as handled by bootloader.
>> - Renamed flexcom3 usart0 to usart3
>> - Added /chosen and /aliases nodes in dts file.
>>
>> v2 -> v3:
>> - Enabling trng in dtsi itself.
>> - Removed "status=okay" dma0.
>> - Add gpio pin settings for can0(missed adding this in previous
>> version)
>>
>> v1 -> v2:
>> - Moved flx3 usart0 node to dtsi file.
>> - Removed status="okay" for dma0 to maintain consistency across nodes
>> (which means enabling dma0 by default)
>>
>> arch/arm/boot/dts/Makefile | 2 +
>> arch/arm/boot/dts/lan966x-pcb8291.dts | 64 +++++++
>> arch/arm/boot/dts/lan966x.dtsi | 237 ++++++++++++++++++++++++++
>> 3 files changed, 303 insertions(+)
>> create mode 100644 arch/arm/boot/dts/lan966x-pcb8291.dts
>> create mode 100644 arch/arm/boot/dts/lan966x.dtsi
>>
>
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/lan966x.dtsi
>> @@ -0,0 +1,237 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +/*
>> + * lan966x.dtsi - Device Tree Include file for Microchip LAN966 family
>> SoC
>> + *
>> + * Copyright (C) 2021 Microchip Technology, Inc. and its subsidiaries
>> + *
>> + * Author: Kavyasree Kotagiri <kavyasree.kotagiri@...rochip.com>
>> + *
>> + */
>> +
>> +#include <dt-bindings/interrupt-controller/irq.h>
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> +#include <dt-bindings/mfd/atmel-flexcom.h>
>> +#include <dt-bindings/dma/at91.h>
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/clock/microchip,lan966x.h>
>> +
>> +/ {
>> + model = "Microchip LAN966 family SoC";
>> + compatible = "microchip,lan966";
>
> As mentioned earlier, this isn't a documented compatible string. So,
> I guess without overwriting this in the board dts it will throw an
> error with the dt schema validator. OTOH, there are many dtsi files
> in arch/arm/boot/dts/ doing this. I don't know what is correct here.
I see it documented here:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/arm/atmel-at91.yaml#n165
Isn't it what is expected?
> Everthing else looks good.
Thanks a lot for your reviews.
> Reviewed-by: Michael Walle <michael@...le.cc>
Acked-by: Nicolas Ferre <nicolas.ferre@...rochip.com>
I'm queuing it to at91-dt branch for reaching arm-soc in 5.18 merge window.
Best regards,
Nicolas
>> + interrupt-parent = <&gic>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> +
>> + cpus {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + cpu@0 {
>> + device_type = "cpu";
>> + compatible = "arm,cortex-a7";
>> + clock-frequency = <600000000>;
>> + reg = <0x0>;
>> + };
>> + };
>> +
>> + clocks {
>> + sys_clk: sys_clk {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <162500000>;
>> + };
>> +
>> + cpu_clk: cpu_clk {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <600000000>;
>> + };
>> +
>> + ddr_clk: ddr_clk {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <300000000>;
>> + };
>> +
>> + nic_clk: nic_clk {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <200000000>;
>> + };
>> + };
>> +
>> + clks: clock-controller@...c00a8 {
>> + compatible = "microchip,lan966x-gck";
>> + #clock-cells = <1>;
>> + clocks = <&cpu_clk>, <&ddr_clk>, <&sys_clk>;
>> + clock-names = "cpu", "ddr", "sys";
>> + reg = <0xe00c00a8 0x38>;
>> + };
>> +
>> + timer {
>> + compatible = "arm,armv7-timer";
>> + interrupt-parent = <&gic>;
>> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) |
>> IRQ_TYPE_LEVEL_LOW)>,
>> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
>> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
>> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
>> + clock-frequency = <37500000>;
>> + };
>> +
>> + soc {
>> + compatible = "simple-bus";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + flx0: flexcom@...40000 {
>> + compatible = "atmel,sama5d2-flexcom";
>> + reg = <0xe0040000 0x100>;
>> + clocks = <&clks GCK_ID_FLEXCOM0>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges = <0x0 0xe0040000 0x800>;
>> + status = "disabled";
>> + };
>> +
>> + flx1: flexcom@...44000 {
>> + compatible = "atmel,sama5d2-flexcom";
>> + reg = <0xe0044000 0x100>;
>> + clocks = <&clks GCK_ID_FLEXCOM1>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges = <0x0 0xe0044000 0x800>;
>> + status = "disabled";
>> + };
>> +
>> + trng: rng@...48000 {
>> + compatible = "atmel,at91sam9g45-trng";
>> + reg = <0xe0048000 0x100>;
>> + clocks = <&nic_clk>;
>> + };
>> +
>> + aes: crypto@...4c000 {
>> + compatible = "atmel,at91sam9g46-aes";
>> + reg = <0xe004c000 0x100>;
>> + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
>> + dmas = <&dma0 AT91_XDMAC_DT_PERID(13)>,
>> + <&dma0 AT91_XDMAC_DT_PERID(12)>;
>> + dma-names = "rx", "tx";
>> + clocks = <&nic_clk>;
>> + clock-names = "aes_clk";
>> + };
>> +
>> + flx2: flexcom@...60000 {
>> + compatible = "atmel,sama5d2-flexcom";
>> + reg = <0xe0060000 0x100>;
>> + clocks = <&clks GCK_ID_FLEXCOM2>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges = <0x0 0xe0060000 0x800>;
>> + status = "disabled";
>> + };
>> +
>> + flx3: flexcom@...64000 {
>> + compatible = "atmel,sama5d2-flexcom";
>> + reg = <0xe0064000 0x100>;
>> + clocks = <&clks GCK_ID_FLEXCOM3>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges = <0x0 0xe0064000 0x800>;
>> + status = "disabled";
>> +
>> + usart3: serial@200 {
>> + compatible = "atmel,at91sam9260-usart";
>> + reg = <0x200 0x200>;
>> + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&nic_clk>;
>> + clock-names = "usart";
>> + atmel,fifo-size = <32>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + dma0: dma-controller@...68000 {
>> + compatible = "microchip,sama7g5-dma";
>> + reg = <0xe0068000 0x1000>;
>> + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
>> + #dma-cells = <1>;
>> + clocks = <&nic_clk>;
>> + clock-names = "dma_clk";
>> + };
>> +
>> + sha: crypto@...6c000 {
>> + compatible = "atmel,at91sam9g46-sha";
>> + reg = <0xe006c000 0xec>;
>> + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
>> + dmas = <&dma0 AT91_XDMAC_DT_PERID(14)>;
>> + dma-names = "tx";
>> + clocks = <&nic_clk>;
>> + clock-names = "sha_clk";
>> + };
>> +
>> + flx4: flexcom@...70000 {
>> + compatible = "atmel,sama5d2-flexcom";
>> + reg = <0xe0070000 0x100>;
>> + clocks = <&clks GCK_ID_FLEXCOM4>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges = <0x0 0xe0070000 0x800>;
>> + status = "disabled";
>> + };
>> +
>> + timer0: timer@...8c000 {
>> + compatible = "snps,dw-apb-timer";
>> + reg = <0xe008c000 0x400>;
>> + clocks = <&nic_clk>;
>> + clock-names = "timer";
>> + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
>> + };
>> +
>> + watchdog: watchdog@...90000 {
>> + compatible = "snps,dw-wdt";
>> + reg = <0xe0090000 0x1000>;
>> + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&nic_clk>;
>> + status = "disabled";
>> + };
>> +
>> + can0: can@...1c000 {
>> + compatible = "bosch,m_can";
>> + reg = <0xe081c000 0xfc>, <0x00100000 0x4000>;
>> + reg-names = "m_can", "message_ram";
>> + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-names = "int0", "int1";
>> + clocks = <&clks GCK_ID_MCAN0>, <&clks GCK_ID_MCAN0>;
>> + clock-names = "hclk", "cclk";
>> + assigned-clocks = <&clks GCK_ID_MCAN0>;
>> + assigned-clock-rates = <40000000>;
>> + bosch,mram-cfg = <0x0 0 0 64 0 0 32 32>;
>> + status = "disabled";
>> + };
>> +
>> + gpio: pinctrl@...04064 {
>> + compatible = "microchip,lan966x-pinctrl";
>> + reg = <0xe2004064 0xb4>,
>> + <0xe2010024 0x138>;
>> + gpio-controller;
>> + #gpio-cells = <2>;
>> + gpio-ranges = <&gpio 0 0 78>;
>> + interrupt-controller;
>> + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
>> + #interrupt-cells = <2>;
>> + };
>> +
>> + gic: interrupt-controller@...11000 {
>> + compatible = "arm,gic-400", "arm,cortex-a7-gic";
>> + #interrupt-cells = <3>;
>> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-controller;
>> + reg = <0xe8c11000 0x1000>,
>> + <0xe8c12000 0x2000>,
>> + <0xe8c14000 0x2000>,
>> + <0xe8c16000 0x2000>;
>> + };
>> + };
>> +};
>
> --
> -michael
--
Nicolas Ferre
Powered by blists - more mailing lists