U-Boot SPL 2022.01-rc1-00054-g52207514ba-dirty (Nov 21 2021 - 03:20:03 +0000) Trying to boot from MMC1 U-Boot 2022.01-rc1-00054-g52207514ba-dirty (Nov 21 2021 - 03:20:03 +0000) CPU: rv64imafdc Model: SiFive HiFive Unmatched A00 DRAM: 16 GiB MMC: spi@10050000:mmc@0: 0 Loading Environment from nowhere... OK EEPROM: SiFive PCB EEPROM format v1 Product ID: 0002 (HiFive Unmatched) PCB revision: 3 BOM revision: B BOM variant: 0 Serial number: SF105SZ212200277 Ethernet MAC address: 70:b3:d5:92:f7:c0 CRC: 0bf17da5 In: serial@10010000 Out: serial@10010000 Err: serial@10010000 Model: SiFive HiFive Unmatched A00 Net: eth0: ethernet@10090000 Hit any key to stop autoboot: 2  0 => pci write.w 02.03.0 0xb0 0x0063 PCIE-0: Link up (Gen1-x8, Bus0) PCI Autoconfig: 02.03.00: Downstream link non-functional PCI Autoconfig: 02.03.00: Retrying with speed restricted to 2.5GT/s... PCI Autoconfig: 02.03.00: Succeeded! => pci display.w 02.03.0 0xb0 1 000000b0: 0063 => boot Device 0: Vendor: 0x144d Rev: 4L2QEXA7 Prod: S3TPNX0K723663 Type: Hard Disk Capacity: 976762.3 MB = 953.8 GB (2000409264 x 512) ... is now current device Scanning nvme 0:1... libfdt fdt_check_header(): FDT_ERR_BADMAGIC 78Scanning disk mmc@0.blk... Scanning disk nvme#0.blk#1... Found 13 disks No EFI system partition BootOrder not defined EFI boot manager: Cannot load any image starting USB... Bus xhci_pci: Register 4000840 NbrPorts 4 Starting the controller USB XHCI 1.00 scanning bus xhci_pci for devices... 4 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Device 0: unknown device switch to partitions #0, OK mmc0 is current device Scanning mmc 0:3... Found /extlinux/extlinux.conf Retrieving file: /extlinux/extlinux.conf 797 bytes read in 12 ms (64.5 KiB/s) OpenEmbedded SiFive HiFive Unmatched 1: linux 2: old 3: 5.11.10 4: test Enter choice: 4 4: test Retrieving file: /Image-test.gz 7527234 bytes read in 6439 ms (1.1 MiB/s) append: root=/dev/mmcblk0p4 rootfstype=ext4 rootwait console=ttySIF0,115200 earlycon pci=hpbussize=16 debug Retrieving file: /hifive-unmatched-a00-test.dtb 9858 bytes read in 16 ms (601.6 KiB/s) Uncompressing Kernel Image Moving Image from 0x84000000 to 0x80200000, end=8116b000 ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 00000000ff732000, end 00000000ff737681 ... OK Starting kernel ... Linux version 5.17.0-rc2-dirty (macro@angie) (riscv64-linux-gnu-gcc (GCC) 12.0.1 20220129 (experimental), GNU ld (GNU Binutils) 2.37.50.20211101) #24 SMP Wed Mar 2 21:24:42 GMT 2022 OF: fdt: Ignoring memory range 0x80000000 - 0x80200000 Machine model: SiFive HiFive Unmatched A00 earlycon: sifive0 at MMIO 0x0000000010010000 (options '') printk: bootconsole [sifive0] enabled efi: UEFI not found. Zone ranges: DMA32 [mem 0x0000000080200000-0x00000000ffffffff] Normal [mem 0x0000000100000000-0x000000047fffffff] Movable zone start for each node Early memory node ranges node 0: [mem 0x0000000080200000-0x000000047fffffff] Initmem setup node 0 [mem 0x0000000080200000-0x000000047fffffff] On node 0, zone DMA32: 512 pages in unavailable ranges SBI specification v0.3 detected SBI implementation ID=0x1 Version=0x9 SBI TIME extension detected SBI IPI extension detected SBI RFENCE extension detected SBI SRST extension detected SBI HSM extension detected CPU with hartid=0 is not available CPU with hartid=0 is not available riscv: ISA extensions acdfim riscv: ELF capabilities acdfim percpu: Embedded 24 pages/cpu s61400 r8192 d28712 u98304 pcpu-alloc: s61400 r8192 d28712 u98304 alloc=24*4096 pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 Built 1 zonelists, mobility grouping on. Total pages: 4136455 Kernel command line: root=/dev/mmcblk0p4 rootfstype=ext4 rootwait console=ttySIF0,115200 earlycon pci=hpbussize=16 debug Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) mem auto-init: stack:off, heap alloc:off, heap free:off software IO TLB: mapped [mem 0x00000000fb732000-0x00000000ff732000] (64MB) Memory: 16421752K/16775168K available (8894K kernel code, 1943K rwdata, 4162K rodata, 409K init, 365K bss, 353416K reserved, 0K cma-reserved) SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 trace event string verifier disabled rcu: Hierarchical RCU implementation. rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. Tracing variant of Tasks RCU enabled. rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 CPU with hartid=0 is not available riscv-intc: unable to find hart id for /cpus/cpu@0/interrupt-controller riscv-intc: 64 local interrupts mapped plic: interrupt-controller@c000000: mapped 69 interrupts with 4 handlers for 9 contexts. random: get_random_bytes called from start_kernel+0x458/0x5e8 with crng_init=0 riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [3] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns sched_clock: 64 bits at 1000kHz, resolution 1000ns, wraps every 2199023255500ns Console: colour dummy device 80x25 Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=4000) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) cblist_init_generic: Setting adjustable number of callback queues. cblist_init_generic: Setting shift to 2 and lim to 1. ASID allocator disabled (0 bits) rcu: Hierarchical SRCU implementation. EFI services will not be available. smp: Bringing up secondary CPUs ... smp: Brought up 1 node, 4 CPUs devtmpfs: initialized clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns futex hash table entries: 1024 (order: 4, 65536 bytes, linear) NET: Registered PF_NETLINK/PF_ROUTE protocol family thermal_sys: Registered thermal governor 'step_wise' iommu: Default domain type: Translated iommu: DMA domain TLB invalidation policy: strict mode vgaarb: loaded SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb EDAC MC: Ver: 3.0.0 Advanced Linux Sound Architecture Driver Initialized. NET: Registered PF_ATMPVC protocol family NET: Registered PF_ATMSVC protocol family clocksource: Switched to clocksource riscv_clocksource VFS: Disk quotas dquot_6.6.0 VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) NET: Registered PF_INET protocol family IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear) tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear) TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear) TCP: Hash tables configured (established 131072 bind 65536) UDP hash table entries: 8192 (order: 6, 262144 bytes, linear) UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes, linear) NET: Registered PF_UNIX/PF_LOCAL protocol family RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. PCI: CLS 0 bytes, default 64 Initialise system trusted keyrings workingset: timestamp_bits=62 max_order=22 bucket_order=0 NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered nfs4filelayout_init: NFSv4 File Layout Driver Registering... nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... Installing knfsd (copyright (C) 1996 okir@monad.swb.de). 9p: Installing v9fs 9p2000 file system support NET: Registered PF_ALG protocol family Key type asymmetric registered Asymmetric key parser 'x509' registered Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) io scheduler mq-deadline registered io scheduler kyber registered shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 fu740-pcie e00000000.pcie: host bridge /soc/pcie@e00000000 ranges: fu740-pcie e00000000.pcie: IO 0x0060080000..0x006008ffff -> 0x0060080000 fu740-pcie e00000000.pcie: MEM 0x0060090000..0x0070ffffff -> 0x0060090000 fu740-pcie e00000000.pcie: MEM 0x2000000000..0x3fffffffff -> 0x2000000000 fu740-pcie e00000000.pcie: iATU unroll: enabled fu740-pcie e00000000.pcie: Detected iATU regions: 8 outbound, 8 inbound fu740-pcie e00000000.pcie: Link up fu740-pcie e00000000.pcie: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] (bus address [0x60080000-0x6008ffff]) pci_bus 0000:00: root bus resource [mem 0x60090000-0x70ffffff] pci_bus 0000:00: root bus resource [mem 0x2000000000-0x3fffffffff pref] pci 0000:00:00.0: [f15e:0000] type 01 class 0x060400 pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x000fffff] pci 0000:00:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref] pci 0000:00:00.0: supports D1 pci 0000:00:00.0: PME# supported from D0 D1 D3hot pci 0000:01:00.0: [1b21:2824] type 01 class 0x060400 pci 0000:01:00.0: enabling Extended Tags pci 0000:01:00.0: PME# supported from D0 D3hot D3cold pci 0000:01:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:02:00.0: [1b21:2824] type 01 class 0x060400 pci 0000:02:00.0: enabling Extended Tags pci 0000:02:00.0: PME# supported from D0 D3hot D3cold pci 0000:02:02.0: [1b21:2824] type 01 class 0x060400 pci 0000:02:02.0: enabling Extended Tags pci 0000:02:02.0: PME# supported from D0 D3hot D3cold pci 0000:02:03.0: [1b21:2824] type 01 class 0x060400 pci 0000:02:03.0: enabling Extended Tags pci 0000:02:03.0: broken device, retraining non-functional downstream link at 2.5GT/s... pci 0000:02:03.0: retraining succeeded! pci 0000:02:03.0: removing 2.5GT/s downstream link speed restriction pci 0000:02:03.0: pcie_downstream_link_retrain+0x0/0x1e4 took 74937 usecs pci 0000:02:03.0: PME# supported from D0 D3hot D3cold pci 0000:02:04.0: [1b21:2824] type 01 class 0x060400 pci 0000:02:04.0: enabling Extended Tags pci 0000:02:04.0: PME# supported from D0 D3hot D3cold pci 0000:02:08.0: [1b21:2824] type 01 class 0x060400 pci 0000:02:08.0: enabling Extended Tags pci 0000:02:08.0: PME# supported from D0 D3hot D3cold pci 0000:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:02:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:02:03.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:02:04.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:02:08.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci_bus 0000:03: busn_res: [bus 03-ff] end is updated to 03 pci 0000:04:00.0: [1b21:1142] type 00 class 0x0c0330 pci 0000:04:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit] pci 0000:04:00.0: PME# supported from D3cold pci_bus 0000:04: busn_res: [bus 04-ff] end is updated to 04 pci 0000:05:00.0: [12d8:2304] type 01 class 0x060400 pci 0000:05:00.0: supports D1 D2 pci 0000:05:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:05:00.0: 4.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x1 link at 0000:02:03.0 (capable of 8.000 Gb/s with 5.0 GT/s PCIe x2 link) pci 0000:05:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:06:01.0: [12d8:2304] type 01 class 0x060400 pci 0000:06:01.0: supports D1 D2 pci 0000:06:01.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:06:02.0: [12d8:2304] type 01 class 0x060400 pci 0000:06:02.0: supports D1 D2 pci 0000:06:02.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:07:00.0: [1415:c144] type 00 class 0x070002 pci 0000:07:00.0: reg 0x10: initial BAR value 0x00000000 invalid pci 0000:07:00.0: reg 0x10: [io size 0x0008] pci 0000:07:00.0: supports D1 D2 pci 0000:07:00.0: PME# supported from D1 D2 D3hot D3cold pci 0000:07:00.1: [1415:c145] type 00 class 0x070002 pci 0000:07:00.1: reg 0x10: initial BAR value 0x00000000 invalid pci 0000:07:00.1: reg 0x10: [io size 0x0008] pci 0000:07:00.1: supports D1 D2 pci 0000:07:00.1: PME# supported from D1 D2 D3hot D3cold pci 0000:07:00.2: [1415:c146] type 00 class 0x088000 pci 0000:07:00.2: reg 0x10: [mem 0x00000000-0x000003ff] pci 0000:07:00.2: reg 0x14: [mem 0x00000000-0x001fffff] pci 0000:07:00.2: supports D1 D2 pci 0000:07:00.2: PME# supported from D1 D2 D3hot D3cold pci_bus 0000:07: busn_res: [bus 07-ff] end is updated to 07 pci 0000:08:00.0: [1b21:1080] type 01 class 0x060400 pci 0000:08:00.0: supports D1 D2 pci 0000:08:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:08:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci_bus 0000:09: extended config space not accessible pci 0000:09:01.0: [1011:000f] type 00 class 0x020200 pci 0000:09:01.0: reg 0x10: [mem 0x70600000-0x7060007f] pci 0000:09:01.0: reg 0x14: [io 0x1000-0x107f] pci 0000:09:01.0: reg 0x18: [mem 0x70610000-0x7061ffff] pci 0000:09:02.0: [111d:0001] type 00 class 0x020300 pci 0000:09:02.0: reg 0x10: [io 0x1100-0x11ff] pci 0000:09:02.0: reg 0x14: [mem 0x70620000-0x70620fff] pci 0000:09:02.0: reg 0x30: [mem 0x70640000-0x7065ffff pref] pci_bus 0000:09: busn_res: [bus 09-ff] end is updated to 09 pci_bus 0000:08: busn_res: [bus 08-ff] end is updated to 09 pci_bus 0000:06: busn_res: [bus 06-ff] end is updated to 09 pci_bus 0000:05: busn_res: [bus 05-ff] end is updated to 09 pci 0000:0a:00.0: [144d:a808] type 00 class 0x010802 pci 0000:0a:00.0: reg 0x10: [mem 0x70700000-0x70703fff 64bit] pci_bus 0000:0a: busn_res: [bus 0a-ff] end is updated to 0a pci_bus 0000:0b: busn_res: [bus 0b-ff] end is updated to 0b pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 0b pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 0b pci 0000:00:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff] pci 0000:00:00.0: BAR 14: assigned [mem 0x60200000-0x607fffff] pci 0000:00:00.0: BAR 6: assigned [mem 0x60090000-0x6009ffff pref] pci 0000:00:00.0: BAR 13: assigned [io 0x0000-0x1fff] pci 0000:01:00.0: BAR 14: assigned [mem 0x60200000-0x607fffff] pci 0000:01:00.0: BAR 13: assigned [io 0x0000-0x1fff] pci 0000:02:02.0: BAR 14: assigned [mem 0x60200000-0x602fffff] pci 0000:02:03.0: BAR 14: assigned [mem 0x60300000-0x606fffff] pci 0000:02:04.0: BAR 14: assigned [mem 0x60700000-0x607fffff] pci 0000:02:03.0: BAR 13: assigned [io 0x0000-0x1fff] pci 0000:02:00.0: PCI bridge to [bus 03] pci 0000:04:00.0: BAR 0: assigned [mem 0x60200000-0x60207fff 64bit] pci 0000:02:02.0: PCI bridge to [bus 04] pci 0000:02:02.0: bridge window [mem 0x60200000-0x602fffff] pci 0000:05:00.0: BAR 14: assigned [mem 0x60300000-0x606fffff] pci 0000:05:00.0: BAR 13: assigned [io 0x0000-0x1fff] pci 0000:06:01.0: BAR 14: assigned [mem 0x60300000-0x605fffff] pci 0000:06:02.0: BAR 14: assigned [mem 0x60600000-0x606fffff] pci 0000:06:01.0: BAR 13: assigned [io 0x0000-0x0fff] pci 0000:06:02.0: BAR 13: assigned [io 0x1000-0x1fff] pci 0000:07:00.2: BAR 1: assigned [mem 0x60400000-0x605fffff] pci 0000:07:00.2: BAR 0: assigned [mem 0x60300000-0x603003ff] pci 0000:07:00.0: BAR 0: assigned [io 0x0008-0x000f] pci 0000:07:00.1: BAR 0: assigned [io 0x0010-0x0017] pci 0000:06:01.0: PCI bridge to [bus 07] pci 0000:06:01.0: bridge window [io 0x0000-0x0fff] pci 0000:06:01.0: bridge window [mem 0x60300000-0x605fffff] pci 0000:08:00.0: BAR 14: assigned [mem 0x60600000-0x606fffff] pci 0000:08:00.0: BAR 13: assigned [io 0x1000-0x1fff] pci 0000:09:02.0: BAR 6: assigned [mem 0x60600000-0x6061ffff pref] pci 0000:09:01.0: BAR 2: assigned [mem 0x60620000-0x6062ffff] pci 0000:09:02.0: BAR 1: assigned [mem 0x60630000-0x60630fff] pci 0000:09:02.0: BAR 0: assigned [io 0x1000-0x10ff] pci 0000:09:01.0: BAR 0: assigned [mem 0x60631000-0x6063107f] pci 0000:09:01.0: BAR 1: assigned [io 0x1100-0x117f] pci 0000:08:00.0: PCI bridge to [bus 09] pci 0000:08:00.0: bridge window [io 0x1000-0x1fff] pci 0000:08:00.0: bridge window [mem 0x60600000-0x606fffff] pci 0000:06:02.0: PCI bridge to [bus 08-09] pci 0000:06:02.0: bridge window [io 0x1000-0x1fff] pci 0000:06:02.0: bridge window [mem 0x60600000-0x606fffff] pci 0000:05:00.0: PCI bridge to [bus 06-09] pci 0000:05:00.0: bridge window [io 0x0000-0x1fff] pci 0000:05:00.0: bridge window [mem 0x60300000-0x606fffff] pci 0000:02:03.0: PCI bridge to [bus 05-09] pci 0000:02:03.0: bridge window [io 0x0000-0x1fff] pci 0000:02:03.0: bridge window [mem 0x60300000-0x606fffff] pci 0000:0a:00.0: BAR 0: assigned [mem 0x60700000-0x60703fff 64bit] pci 0000:02:04.0: PCI bridge to [bus 0a] pci 0000:02:04.0: bridge window [mem 0x60700000-0x607fffff] pci 0000:02:08.0: PCI bridge to [bus 0b] pci 0000:01:00.0: PCI bridge to [bus 02-0b] pci 0000:01:00.0: bridge window [io 0x0000-0x1fff] pci 0000:01:00.0: bridge window [mem 0x60200000-0x607fffff] pci 0000:00:00.0: PCI bridge to [bus 01-0b] pci 0000:00:00.0: bridge window [io 0x0000-0x1fff] pci 0000:00:00.0: bridge window [mem 0x60200000-0x607fffff] pcieport 0000:00:00.0: AER: enabled with IRQ 46 pcieport 0000:01:00.0: enabling device (0000 -> 0003) pcieport 0000:02:02.0: enabling device (0000 -> 0002) pcieport 0000:02:03.0: enabling device (0000 -> 0003) pcieport 0000:02:04.0: enabling device (0000 -> 0002) pci 0000:04:00.0: enabling device (0000 -> 0002) pcieport 0000:05:00.0: enabling device (0000 -> 0003) pci 0000:08:00.0: Disabling ASPM L0s/L1 switchtec: loaded. L2CACHE: DataError @ 0x00000002.82000030 L2CACHE: No. of Banks in the cache: 4 L2CACHE: No. of ways per bank: 16 L2CACHE: Sets per bank: 512 L2CACHE: Bytes per cache block: 64 L2CACHE: Index of the largest way enabled: 15 Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled serial 0000:07:00.0: enabling device (0000 -> 0001) serial 0000:07:00.0: detected caps 00000700 should be 00000500 0000:07:00.0: ttyS0 at I/O 0x8 (irq = 38, base_baud = 15625000) is a 16C950/954 serial 0000:07:00.1: enabling device (0000 -> 0001) serial 0000:07:00.1: detected caps 00000700 should be 00000500 0000:07:00.1: ttyS1 at I/O 0x10 (irq = 39, base_baud = 15625000) is a 16C950/954 10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 115200) is a SiFive UART v0 printk: console [ttySIF0] enabled printk: console [ttySIF0] enabled printk: bootconsole [sifive0] disabled printk: bootconsole [sifive0] disabled 10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 2, base_baud = 115200) is a SiFive UART v0 lp: driver loaded but no devices found ppdev: user-space parallel port driver loop: module loaded nvme nvme0: pci function 0000:0a:00.0 nvme 0000:0a:00.0: enabling device (0000 -> 0002) Rounding down aligned max_sectors from 4294967295 to 4294967288 db_root: cannot open: /etc/target nvme nvme0: Shutdown timeout set to 8 seconds sifive_spi 10040000.spi: mapped; irq=4, cs=1 spi-nor spi0.0: is25wp256 (32768 Kbytes) sifive_spi 10050000.spi: mapped; irq=6, cs=1 macb 10090000.ethernet: Registered clk switch 'sifive-gemgxl-mgmt' nvme nvme0: 4/0/0 default/read/poll queues macb 10090000.ethernet eth0: Cadence GEM rev 0x10070109 at 0x10090000 irq 7 (70:b3:d5:92:f7:c0) e1000e: Intel(R) PRO/1000 Network Driver e1000e: Copyright(c) 1999 - 2015 Intel Corporation. defxx: v1.12 2021/03/10 Lawrence V. Stefani and others pci 0000:08:00.0: enabling device (0000 -> 0003) nvme0n1: p1 p2 p3 < p5 p6 p7 p8 > 0000:09:01.0: DEFPA at MMIO addr = 0x60631000, IRQ = 40, Hardware addr = 00-60-6d-93-99-95 0000:09:01.0: registered as fddi0 nicstar0: PHY seems to be 155 Mbps. nicstar0: MAC address 00:e0:cf:00:00:b5 nicstar(itf 0): no signal nicstar(itf 0): signal lost ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-pci: OHCI PCI platform driver uhci_hcd: USB Universal Host Controller Interface driver xhci_hcd 0000:04:00.0: xHCI Host Controller xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 1 xhci_hcd 0000:04:00.0: hcc params 0x0200e080 hci version 0x100 quirks 0x0000000010800410 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.17 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: xHCI Host Controller usb usb1: Manufacturer: Linux 5.17.0-rc2-dirty xhci-hcd usb usb1: SerialNumber: 0000:04:00.0 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected xhci_hcd 0000:04:00.0: xHCI Host Controller xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 2 xhci_hcd 0000:04:00.0: Host supports USB 3.0 SuperSpeed usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.17 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: xHCI Host Controller usb usb2: Manufacturer: Linux 5.17.0-rc2-dirty xhci-hcd usb usb2: SerialNumber: 0000:04:00.0 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new interface driver usb-storage usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic mousedev: PS/2 mouse device common for all mice usbcore: registered new interface driver usbtouchscreen i2c_dev: i2c /dev entries driver da9063 0-0058: Device detected (chip-ID: 0x61, var-ID: 0x73) random: fast init done da9063-rtc da9063-rtc: DMA mask not set da9063-rtc da9063-rtc: registered as rtc0 da9063-rtc da9063-rtc: setting system clock to 2022-03-02T21:31:37 UTC (1646256697) poweroff-gpio gpio-poweroff: gpio_poweroff_probe: pm_power_off function already registered poweroff-gpio: probe of gpio-poweroff failed with error -16 EDAC DEVICE0: Giving out device to module Sifive ECC Manager controller sifive_edac.0: DEV sifive_edac.0 (INTERRUPT) mmc_spi spi1.0: SD/MMC host mmc0, no DMA, no WP, no poweroff ledtrig-cpu: registered to indicate activity on CPUs usbcore: registered new interface driver usbhid usbhid: USB HID core driver usbcore: registered new interface driver snd-usb-audio NET: Registered PF_INET6 protocol family Segment Routing with IPv6 In-situ OAM (IOAM) with IPv6 sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver NET: Registered PF_PACKET protocol family lec:lane_module_init: lec.c: initialized mpoa:atm_mpoa_init: mpc.c: initialized 9pnet: Installing 9P2000 support Key type dns_resolver registered Loading compiled-in X.509 certificates ALSA device list: No soundcards found. Waiting for root device /dev/mmcblk0p4... usb 1-2: new high-speed USB device number 2 using xhci_hcd mmc0: host does not support reading read-only switch, assuming write-enable mmc0: new SDHC card on SPI mmcblk0: mmc0:0000 SD32G 29.7 GiB mmcblk0: p1 p2 p3 p4 EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Quota mode: none. VFS: Mounted root (ext4 filesystem) readonly on device 179:4. devtmpfs: mounted Freeing unused kernel image (initmem) memory: 408K Kernel memory protection not selected by kernel config. Run /sbin/init as init process with arguments: /sbin/init with environment: HOME=/ TERM=linux usb 1-2: New USB device found, idVendor=174c, idProduct=2074, bcdDevice= 0.01 usb 1-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1 usb 1-2: Product: AS2107 usb 1-2: Manufacturer: ASMedia usb 1-2: SerialNumber: USB2.0 Hub hub 1-2:1.0: USB hub found hub 1-2:1.0: 4 ports detected usb 2-2: new SuperSpeed USB device number 2 using xhci_hcd usb 2-2: New USB device found, idVendor=174c, idProduct=3074, bcdDevice= 0.01 usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1 usb 2-2: Product: AS2107 usb 2-2: Manufacturer: ASMedia usb 2-2: SerialNumber: USB2.0 Hub hub 2-2:1.0: USB hub found hub 2-2:1.0: 4 ports detected usb 1-2.4: new high-speed USB device number 3 using xhci_hcd usb 1-2.4: New USB device found, idVendor=2109, idProduct=2817, bcdDevice=90.24 usb 1-2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-2.4: Product: USB2.0 Hub usb 1-2.4: Manufacturer: VIA Labs, Inc. hub 1-2.4:1.0: USB hub found hub 1-2.4:1.0: 4 ports detected