| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20220315032411.2826-5-leilk.liu@mediatek.com>
Date: Tue, 15 Mar 2022 11:24:09 +0800
From: Leilk Liu <leilk.liu@...iatek.com>
To: Mark Brown <broonie@...nel.org>
CC: Rob Herring <robh+dt@...nel.org>,
Matthias Brugger <matthias.bgg@...il.com>,
<devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-spi@...r.kernel.org>, <linux-mediatek@...ts.infradead.org>,
Leilk Liu <leilk.liu@...iatek.com>
Subject: [PATCH V4 4/6] spi: mediatek: add spi memory support for ipm design
this patch add the support of spi-mem for ipm design.
Signed-off-by: Leilk Liu <leilk.liu@...iatek.com>
---
drivers/spi/spi-mt65xx.c | 349 ++++++++++++++++++++++++++++++++++++++-
1 file changed, 348 insertions(+), 1 deletion(-)
diff --git a/drivers/spi/spi-mt65xx.c b/drivers/spi/spi-mt65xx.c
index 1a0b3208dfca..8958c3fa4fea 100644
--- a/drivers/spi/spi-mt65xx.c
+++ b/drivers/spi/spi-mt65xx.c
@@ -17,6 +17,7 @@
#include <linux/platform_data/spi-mt65xx.h>
#include <linux/pm_runtime.h>
#include <linux/spi/spi.h>
+#include <linux/spi/spi-mem.h>
#include <linux/dma-mapping.h>
#define SPI_CFG0_REG 0x0000
@@ -78,8 +79,21 @@
#define SPI_CMD_IPM_GET_TICKDLY_OFFSET 22
#define SPI_CMD_IPM_GET_TICKDLY_MASK GENMASK(24, 22)
+
+#define PIN_MODE_CFG(x) ((x) / 2)
+
+#define SPI_CFG3_IPM_PIN_MODE_OFFSET 0
#define SPI_CFG3_IPM_HALF_DUPLEX_DIR BIT(2)
#define SPI_CFG3_IPM_HALF_DUPLEX_EN BIT(3)
+#define SPI_CFG3_IPM_XMODE_EN BIT(4)
+#define SPI_CFG3_IPM_NODATA_FLAG BIT(5)
+#define SPI_CFG3_IPM_CMD_BYTELEN_OFFSET 8
+#define SPI_CFG3_IPM_ADDR_BYTELEN_OFFSET 12
+
+#define SPI_CFG3_IPM_CMD_PIN_MODE_MASK GENMASK(1, 0)
+#define SPI_CFG3_IPM_CMD_BYTELEN_MASK GENMASK(11, 8)
+#define SPI_CFG3_IPM_ADDR_BYTELEN_MASK GENMASK(15, 12)
+
#define MT8173_SPI_MAX_PAD_SEL 3
#define MTK_SPI_PAUSE_INT_STATUS 0x2
@@ -90,6 +104,8 @@
#define MTK_SPI_MAX_FIFO_SIZE 32U
#define MTK_SPI_PACKET_SIZE 1024
#define MTK_SPI_IPM_PACKET_SIZE SZ_64K
+#define MTK_SPI_IPM_PACKET_LOOP SZ_256
+
#define MTK_SPI_32BITS_MASK (0xffffffff)
#define DMA_ADDR_EXT_BITS (36)
@@ -107,7 +123,6 @@ struct mtk_spi_compatible {
bool no_need_unprepare;
/* IPM design adjust and extend register to support more features */
bool ipm_design;
-
};
struct mtk_spi {
@@ -123,6 +138,11 @@ struct mtk_spi {
u32 tx_sgl_len, rx_sgl_len;
const struct mtk_spi_compatible *dev_comp;
u32 spi_clk_hz;
+ struct completion spimem_done;
+ bool use_spimem;
+ struct device *dev;
+ dma_addr_t tx_dma;
+ dma_addr_t rx_dma;
};
static const struct mtk_spi_compatible mtk_common_compat;
@@ -704,6 +724,12 @@ static irqreturn_t mtk_spi_interrupt(int irq, void *dev_id)
else
mdata->state = MTK_SPI_IDLE;
+ /* SPI-MEM ops */
+ if (mdata->use_spimem) {
+ complete(&mdata->spimem_done);
+ return IRQ_HANDLED;
+ }
+
if (!master->can_dma(master, NULL, trans)) {
if (trans->rx_buf) {
cnt = mdata->xfer_len / 4;
@@ -787,6 +813,320 @@ static irqreturn_t mtk_spi_interrupt(int irq, void *dev_id)
return IRQ_HANDLED;
}
+static int mtk_spi_mem_adjust_op_size(struct spi_mem *mem,
+ struct spi_mem_op *op)
+{
+ int opcode_len;
+
+ if (op->data.dir != SPI_MEM_NO_DATA) {
+ opcode_len = 1 + op->addr.nbytes + op->dummy.nbytes;
+ if (opcode_len + op->data.nbytes > MTK_SPI_IPM_PACKET_SIZE) {
+ op->data.nbytes = MTK_SPI_IPM_PACKET_SIZE - opcode_len;
+ /* force data buffer dma-aligned. */
+ op->data.nbytes -= op->data.nbytes % 4;
+ }
+ }
+
+ return 0;
+}
+
+static bool mtk_spi_mem_supports_op(struct spi_mem *mem,
+ const struct spi_mem_op *op)
+{
+ if (op->data.buswidth > 4 || op->addr.buswidth > 4 ||
+ op->dummy.buswidth > 4 || op->cmd.buswidth > 4)
+ return false;
+
+ if (op->addr.nbytes && op->dummy.nbytes &&
+ op->addr.buswidth != op->dummy.buswidth)
+ return false;
+
+ if (op->addr.nbytes + op->dummy.nbytes > 16)
+ return false;
+
+ if (op->data.nbytes > MTK_SPI_IPM_PACKET_SIZE) {
+ if (op->data.nbytes / MTK_SPI_IPM_PACKET_SIZE >
+ MTK_SPI_IPM_PACKET_LOOP ||
+ op->data.nbytes % MTK_SPI_IPM_PACKET_SIZE != 0)
+ return false;
+ }
+
+ return true;
+}
+
+static void mtk_spi_mem_setup_dma_xfer(struct spi_master *master,
+ const struct spi_mem_op *op)
+{
+ struct mtk_spi *mdata = spi_master_get_devdata(master);
+
+ writel((u32)(mdata->tx_dma & MTK_SPI_32BITS_MASK),
+ mdata->base + SPI_TX_SRC_REG);
+#ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT
+ if (mdata->dev_comp->dma_ext)
+ writel((u32)(mdata->tx_dma >> 32),
+ mdata->base + SPI_TX_SRC_REG_64);
+#endif
+
+ if (op->data.dir == SPI_MEM_DATA_IN) {
+ writel((u32)(mdata->rx_dma & MTK_SPI_32BITS_MASK),
+ mdata->base + SPI_RX_DST_REG);
+#ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT
+ if (mdata->dev_comp->dma_ext)
+ writel((u32)(mdata->rx_dma >> 32),
+ mdata->base + SPI_RX_DST_REG_64);
+#endif
+ }
+}
+
+static int mtk_spi_transfer_wait(struct spi_mem *mem,
+ const struct spi_mem_op *op)
+{
+ struct mtk_spi *mdata = spi_master_get_devdata(mem->spi->master);
+ /*
+ * For each byte we wait for 8 cycles of the SPI clock.
+ * Since speed is defined in Hz and we want milliseconds,
+ * so it should be 8 * 1000.
+ */
+ u64 ms = 8000LL;
+
+ if (op->data.dir == SPI_MEM_NO_DATA)
+ ms *= 32; /* prevent we may get 0 for short transfers. */
+ else
+ ms *= op->data.nbytes;
+ ms = div_u64(ms, mem->spi->max_speed_hz);
+ ms += ms + 1000; /* 1s tolerance */
+
+ if (ms > UINT_MAX)
+ ms = UINT_MAX;
+
+ if (!wait_for_completion_timeout(&mdata->spimem_done,
+ msecs_to_jiffies(ms))) {
+ dev_err(mdata->dev, "spi-mem transfer timeout\n");
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+static int mtk_spi_mem_exec_op(struct spi_mem *mem,
+ const struct spi_mem_op *op)
+{
+ struct mtk_spi *mdata = spi_master_get_devdata(mem->spi->master);
+ u32 reg_val, nio, tx_size;
+ char *tx_tmp_buf, *rx_tmp_buf;
+ int ret = 0;
+
+ mdata->use_spimem = true;
+ reinit_completion(&mdata->spimem_done);
+
+ mtk_spi_reset(mdata);
+ mtk_spi_hw_init(mem->spi->master, mem->spi);
+ mtk_spi_prepare_transfer(mem->spi->master, mem->spi->max_speed_hz);
+
+ reg_val = readl(mdata->base + SPI_CFG3_IPM_REG);
+ /* opcode byte len */
+ reg_val &= ~SPI_CFG3_IPM_CMD_BYTELEN_MASK;
+ reg_val |= 1 << SPI_CFG3_IPM_CMD_BYTELEN_OFFSET;
+
+ /* addr & dummy byte len */
+ reg_val &= ~SPI_CFG3_IPM_ADDR_BYTELEN_MASK;
+ if (op->addr.nbytes || op->dummy.nbytes)
+ reg_val |= (op->addr.nbytes + op->dummy.nbytes) <<
+ SPI_CFG3_IPM_ADDR_BYTELEN_OFFSET;
+
+ /* data byte len */
+ if (op->data.dir == SPI_MEM_NO_DATA) {
+ reg_val |= SPI_CFG3_IPM_NODATA_FLAG;
+ writel(0, mdata->base + SPI_CFG1_REG);
+ } else {
+ reg_val &= ~SPI_CFG3_IPM_NODATA_FLAG;
+ mdata->xfer_len = op->data.nbytes;
+ mtk_spi_setup_packet(mem->spi->master);
+ }
+
+ if (op->addr.nbytes || op->dummy.nbytes) {
+ if (op->addr.buswidth == 1 || op->dummy.buswidth == 1)
+ reg_val |= SPI_CFG3_IPM_XMODE_EN;
+ else
+ reg_val &= ~SPI_CFG3_IPM_XMODE_EN;
+ }
+
+ if (op->addr.buswidth == 2 ||
+ op->dummy.buswidth == 2 ||
+ op->data.buswidth == 2)
+ nio = 2;
+ else if (op->addr.buswidth == 4 ||
+ op->dummy.buswidth == 4 ||
+ op->data.buswidth == 4)
+ nio = 4;
+ else
+ nio = 1;
+
+ reg_val &= ~SPI_CFG3_IPM_CMD_PIN_MODE_MASK;
+ reg_val |= PIN_MODE_CFG(nio) << SPI_CFG3_IPM_PIN_MODE_OFFSET;
+
+ reg_val |= SPI_CFG3_IPM_HALF_DUPLEX_EN;
+ if (op->data.dir == SPI_MEM_DATA_IN)
+ reg_val |= SPI_CFG3_IPM_HALF_DUPLEX_DIR;
+ else
+ reg_val &= ~SPI_CFG3_IPM_HALF_DUPLEX_DIR;
+ writel(reg_val, mdata->base + SPI_CFG3_IPM_REG);
+
+ tx_size = 1 + op->addr.nbytes + op->dummy.nbytes;
+ if (op->data.dir == SPI_MEM_DATA_OUT)
+ tx_size += op->data.nbytes;
+
+ tx_size = max_t(u32, tx_size, 32);
+
+ tx_tmp_buf = kzalloc(tx_size, GFP_KERNEL | GFP_DMA);
+ if (!tx_tmp_buf) {
+ mdata->use_spimem = false;
+ return -ENOMEM;
+ }
+
+ tx_tmp_buf[0] = op->cmd.opcode;
+
+ if (op->addr.nbytes) {
+ int i;
+
+ for (i = 0; i < op->addr.nbytes; i++)
+ tx_tmp_buf[i + 1] = op->addr.val >>
+ (8 * (op->addr.nbytes - i - 1));
+ }
+
+ if (op->dummy.nbytes)
+ memset(tx_tmp_buf + op->addr.nbytes + 1,
+ 0xff,
+ op->dummy.nbytes);
+
+ if (op->data.nbytes && op->data.dir == SPI_MEM_DATA_OUT)
+ memcpy(tx_tmp_buf + op->dummy.nbytes + op->addr.nbytes + 1,
+ op->data.buf.out,
+ op->data.nbytes);
+
+ mdata->tx_dma = dma_map_single(mdata->dev, tx_tmp_buf,
+ tx_size, DMA_TO_DEVICE);
+ if (dma_mapping_error(mdata->dev, mdata->tx_dma)) {
+ ret = -ENOMEM;
+ goto err_exit;
+ }
+
+ if (op->data.dir == SPI_MEM_DATA_IN) {
+ if (!IS_ALIGNED((size_t)op->data.buf.in, 4)) {
+ rx_tmp_buf = kzalloc(op->data.nbytes,
+ GFP_KERNEL | GFP_DMA);
+ if (!rx_tmp_buf) {
+ ret = -ENOMEM;
+ goto unmap_tx_dma;
+ }
+ } else {
+ rx_tmp_buf = op->data.buf.in;
+ }
+
+ mdata->rx_dma = dma_map_single(mdata->dev,
+ rx_tmp_buf,
+ op->data.nbytes,
+ DMA_FROM_DEVICE);
+ if (dma_mapping_error(mdata->dev, mdata->rx_dma)) {
+ ret = -ENOMEM;
+ goto kfree_rx_tmp_buf;
+ }
+ }
+
+ reg_val = readl(mdata->base + SPI_CMD_REG);
+ reg_val |= SPI_CMD_TX_DMA;
+ if (op->data.dir == SPI_MEM_DATA_IN)
+ reg_val |= SPI_CMD_RX_DMA;
+ writel(reg_val, mdata->base + SPI_CMD_REG);
+
+ mtk_spi_mem_setup_dma_xfer(mem->spi->master, op);
+
+ mtk_spi_enable_transfer(mem->spi->master);
+
+ /* Wait for the interrupt. */
+ ret = mtk_spi_transfer_wait(mem, op);
+ if (ret)
+ goto unmap_rx_dma;
+
+ /* spi disable dma */
+ reg_val = readl(mdata->base + SPI_CMD_REG);
+ reg_val &= ~SPI_CMD_TX_DMA;
+ if (op->data.dir == SPI_MEM_DATA_IN)
+ reg_val &= ~SPI_CMD_RX_DMA;
+ writel(reg_val, mdata->base + SPI_CMD_REG);
+
+unmap_rx_dma:
+ if (op->data.dir == SPI_MEM_DATA_IN) {
+ dma_unmap_single(mdata->dev, mdata->rx_dma,
+ op->data.nbytes, DMA_FROM_DEVICE);
+ if (!IS_ALIGNED((size_t)op->data.buf.in, 4))
+ memcpy(op->data.buf.in, rx_tmp_buf, op->data.nbytes);
+ }
+kfree_rx_tmp_buf:
+ if (op->data.dir == SPI_MEM_DATA_IN &&
+ !IS_ALIGNED((size_t)op->data.buf.in, 4))
+ kfree(rx_tmp_buf);
+unmap_tx_dma:
+ dma_unmap_single(mdata->dev, mdata->tx_dma,
+ tx_size, DMA_TO_DEVICE);
+err_exit:
+ kfree(tx_tmp_buf);
+ mdata->use_spimem = false;
+
+ return ret;
+}
+
+static const struct spi_controller_mem_ops mtk_spi_mem_ops = {
+ .adjust_op_size = mtk_spi_mem_adjust_op_size,
+ .supports_op = mtk_spi_mem_supports_op,
+ .exec_op = mtk_spi_mem_exec_op,
+};
+
+static void of_mtk_spi_parse_dt(struct spi_master *master, struct device_node *nc)
+{
+ struct mtk_spi *mdata = spi_master_get_devdata(master);
+ u32 value;
+
+ if (!of_property_read_u32(nc, "spi-tx-bus-width", &value)) {
+ switch (value) {
+ case 1:
+ break;
+ case 2:
+ master->mode_bits |= SPI_TX_DUAL;
+ break;
+ case 4:
+ master->mode_bits |= SPI_TX_QUAD;
+ break;
+ default:
+ dev_warn(mdata->dev,
+ "spi-tx-bus-width %d not supported\n",
+ value);
+ break;
+ }
+ }
+
+ if (!of_property_read_u32(nc, "spi-rx-bus-width", &value)) {
+ switch (value) {
+ case 1:
+ break;
+ case 2:
+ master->mode_bits |= SPI_RX_DUAL;
+ break;
+ case 4:
+ master->mode_bits |= SPI_RX_QUAD;
+ break;
+ case 8:
+ master->mode_bits |= SPI_RX_OCTAL;
+ break;
+ default:
+ dev_warn(mdata->dev,
+ "spi-rx-bus-width %d not supported\n",
+ value);
+ break;
+ }
+ }
+}
+
static int mtk_spi_probe(struct platform_device *pdev)
{
struct spi_master *master;
@@ -830,6 +1170,13 @@ static int mtk_spi_probe(struct platform_device *pdev)
if (mdata->dev_comp->ipm_design)
master->mode_bits |= SPI_LOOP;
+ if (mdata->dev_comp->ipm_design) {
+ mdata->dev = &pdev->dev;
+ master->mem_ops = &mtk_spi_mem_ops;
+ of_mtk_spi_parse_dt(master, pdev->dev.of_node);
+ init_completion(&mdata->spimem_done);
+ }
+
if (mdata->dev_comp->need_pad_sel) {
mdata->pad_num = of_property_count_u32_elems(
pdev->dev.of_node,
--
2.25.1
Powered by blists - more mailing lists