Message-ID: <20220317204126.GA723808@bhelgaas>
Date:   Thu, 17 Mar 2022 15:41:26 -0500
From:   Bjorn Helgaas <helgaas@...nel.org>
To:     Andy Shevchenko <andriy.shevchenko@...ux.intel.com>
Cc:     Bjorn Helgaas <bhelgaas@...gle.com>, linux-pci@...r.kernel.org,
        linux-kernel@...r.kernel.org, micklorain@...tonmail.com,
        Alex Williamson <alex.williamson@...hat.com>
Subject: Re: [PATCH v1 1/1] PCI: Enable INTx quirk for ATI PCIe-USB adapter

On Thu, Mar 17, 2022 at 10:59:28AM +0200, Andy Shevchenko wrote:
> On Wed, Mar 16, 2022 at 04:15:48PM -0500, Bjorn Helgaas wrote:
> > On Wed, Mar 16, 2022 at 06:12:19PM +0200, Andy Shevchenko wrote:
> > > On Wed, Mar 16, 2022 at 06:52:09AM -0500, Bjorn Helgaas wrote:
> > > > On Wed, Mar 16, 2022 at 12:27:57PM +0200, Andy Shevchenko wrote:
> > > > > On Tue, Mar 15, 2022 at 03:22:31PM -0500, Bjorn Helgaas wrote:
> > > > > > On Tue, Mar 15, 2022 at 12:09:08PM +0200, Andy Shevchenko wrote:
> > > > > > > On Mon, Mar 14, 2022 at 02:42:53PM -0500, Bjorn Helgaas wrote:
> > > > > > > > On Mon, Mar 14, 2022 at 12:14:48PM +0200, Andy Shevchenko wrote:
> > > > > > > > > ATI PCIe-USB adapter advertises MSI, but it doesn't work
> > > > > > > > > if INTx is disabled.  Enable the respective quirk as
> > > > > > > > > it's done for other ATI devices on this chipset,
> > > > > > > > > 
> > > > > > > > > Fixes: 306c54d0edb6 ("usb: hcd: Try MSI interrupts on
> > > > > > > > > PCI devices")
> > 
> > > > > > Anyway, I applied this to pci/msi for v5.18 with the following
> > > > > > commit log:
> > > > > > 
> > > > > >     PCI: Disable broken MSI on ATI SB600 USB adapters
> > > > > > 
> > > > > >     Some ATI SB600 USB adapters advertise MSI, but MSI doesn't
> > > > > >     work if INTx is disabled.  Disable MSI on these adapters.
> > > > > 
> > > > > But IIUC MSI is _not_ disabled. That's why I have issued this
> > > > > version of the patch with different commit message. Did I
> > > > > misunderstand something?
> > > > 
> > > > Oh, right, of course.  Sorry, I was asleep at the wheel.
> > > 
> > > Are you going to fix that?
> > 
> > Yes, of course, I'll do something with the commit message after we
> > figure out how to handle PCI_COMMAND_INTX_DISABLE.
> > 
> > > > I guess it's just that for these devices, we don't disable INTx
> > > > when enabling MSI.  I can't remember why we disable INTx when
> > > > enabling MSI, but it raises the question of whether it's better to
> > > > leave INTx enabled or to just disable use of MSI completely.
> > > 
> > > It's required by specification to disable INTx if I read 6.1.4.3
> > > Enabling Operation correctly.
> > 
> > Thanks for the reference; I was looking for something like that.  But
> > I don't think this section requires us to set
> > PCI_COMMAND_INTX_DISABLE.  For the benefit of folks without the spec,
> > PCIe r6.0, sec 6.1.4.3 says:
> > 
> >   To maintain backward compatibility, the MSI Enable bit in the
> >   Message Control Register for MSI and the MSI-X Enable bit in the
> >   Message Control Register for MSI-X are each Clear by default (MSI
> >   and MSI-X are both disabled). System configuration software Sets one
> >   of these bits to enable either MSI or MSI-X, but never both
> >   simultaneously. Behavior is undefined if both MSI and MSI-X are
> >   enabled simultaneously. Software disabling either mechanism during
> >   active operation may result in the Function dropping pending
> >   interrupt conditions or failing to recognize new interrupt
> >   conditions. While enabled for MSI or MSI-X operation, a Function is
> >   prohibited from using INTx interrupts (if implemented) to request
> >   service (MSI, MSI-X, and INTx are mutually exclusive).
> > 
> > The only *software* constraints I see are (1) software must never
> > enable both MSI and MSI-X simultaneously, and (2) if software disables
> > MSI or MSI-X during active operation, the Function may fail to
> > generate an interrupt when it should.
> > 
> > I read the last sentence as a constraint on the *hardware*: if either
> > MSI or MSI-X is enabled, the Function is not allowed to use INTx,
> > regardless of the state of PCI_COMMAND_INTX_DISABLE.
> > 
> > I searched the spec for "Interrupt Disable", looking for situations
> > where software might be *required* to set it, but I didn't see
> > anything.
> > 
> > I suspect "Interrupt Disable" was intended to help the OS stop all
> > activity from a device during hot-plug or reconfiguration, as hinted
> > at in sec 6.4, "Device Synchronization":
> > 
> >   The ability of the driver and/or system software to block new
> >   Requests from the device is supported by the Bus Master Enable,
> >   SERR# Enable, and Interrupt Disable bits in the Command register
> >   (Section 7.5.1.1.3) of each device Function, and other such control
> >   bits.
> > 
> > So I'm trying to figure out why when enabling MSI we need to set
> > PCI_COMMAND_INTX_DISABLE for most devices, but it's safe to skip that
> > for these quirked devices.
> 
> I guess it's wrong wording in the last paragraph. It's not safe, but it's
> _required_ since HW doesn't follow PCI specification that clearly says:
> "MSI, MSI-X, and INTx are mutually exclusive".

I agree there's a defect in these SB600 devices.  My guess is that
PCI_COMMAND_INTX_DISABLE actually disables both INTx and MSI, when
it's only supposed to disable INTx.

I'm pretty sure the spec doesn't actually require software to set
Interrupt Disable when enabling MSI, since MSI was added in PCI r2.2,
which included this text in sec 6.8.2:

  System configuration software sets [the MSI Enable] bit to enable
  MSI. ...  Once enabled, a function is prohibited from using its
  INTx# pin (if implemented) to request service (MSI and INTx# are
  mutually exclusive).

and Interrupt Disable was added later, in PCI r2.3, with no mention of
a connection with MSI.  All the specs from PCI r2.2 to PCIe r6.0
include the text above about not using INTx# if MSI or MSI-X is
enabled, but that's not the same as requiring software to set
Interrupt Disable.  Linux has set Interrupt Disable when enabling MSI
ever since MSI support was added [1], so I would hesitate to change
that even though I don't think it's required.

What I don't like about PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG is that it
changes the generic code path in a sort of random way, i.e., this
device becomes yet another special case in how we handle Interrupt
Disable.

What would you think about just setting pdev->no_msi instead, so we
don't try to use MSI at all on these devices?  I think that's what we
did before 306c54d0edb6.

[1] https://lore.kernel.org/all/200310032215.h93MFnjT005788@snoqualmie.dp.intel.com/ (search for PCI_COMMAND_INTX_DISABLE)

Powered by blists - more mailing lists