| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20220322195455.703921-6-prasanna.vengateshan@microchip.com>
Date: Wed, 23 Mar 2022 01:24:50 +0530
From: Prasanna Vengateshan <prasanna.vengateshan@...rochip.com>
To: <andrew@...n.ch>, <netdev@...r.kernel.org>, <olteanv@...il.com>,
<robh+dt@...nel.org>
CC: <UNGLinuxDriver@...rochip.com>, <woojung.huh@...rochip.com>,
<hkallweit1@...il.com>, <linux@...linux.org.uk>,
<davem@...emloft.net>, <kuba@...nel.org>,
<linux-kernel@...r.kernel.org>, <vivien.didelot@...il.com>,
<f.fainelli@...il.com>, <devicetree@...r.kernel.org>,
<pabeni@...hat.com>
Subject: [PATCH v10 net-next 05/10] net: dsa: microchip: add DSA support for microchip lan937x
Basic DSA driver support for lan937x and the device will be
configured through SPI interface.
drivers/net/dsa/microchip/ path is already part of MAINTAINERS &
the new files come under this path. Hence no update needed to the
MAINTAINERS
Reused KSZ APIs for port_bridge_join() & port_bridge_leave() and
added support for port_stp_state_set() & port_fast_age().
lan937x_flush_dyn_mac_table() which gets called from
port_fast_age() of KSZ common layer, hence added support for it.
RGMII internal delay values for the mac is retrieved from
rx-internal-delay-ps & tx-internal-delay-ps as per the feedback from
v3 patch series.
https://lore.kernel.org/netdev/20210802121550.gqgbipqdvp5x76ii@skbuf/
It supports standard delay 2ns only. If the property is not found, the value
will be forced to 0.
Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@...rochip.com>
---
drivers/net/dsa/microchip/Kconfig | 12 +
drivers/net/dsa/microchip/Makefile | 5 +
drivers/net/dsa/microchip/ksz_common.h | 5 +
drivers/net/dsa/microchip/lan937x_dev.c | 631 +++++++++++++++++++++
drivers/net/dsa/microchip/lan937x_dev.h | 117 ++++
drivers/net/dsa/microchip/lan937x_main.c | 320 +++++++++++
drivers/net/dsa/microchip/lan937x_reg.h | 688 +++++++++++++++++++++++
drivers/net/dsa/microchip/lan937x_spi.c | 236 ++++++++
8 files changed, 2014 insertions(+)
create mode 100644 drivers/net/dsa/microchip/lan937x_dev.c
create mode 100644 drivers/net/dsa/microchip/lan937x_dev.h
create mode 100644 drivers/net/dsa/microchip/lan937x_main.c
create mode 100644 drivers/net/dsa/microchip/lan937x_reg.h
create mode 100644 drivers/net/dsa/microchip/lan937x_spi.c
diff --git a/drivers/net/dsa/microchip/Kconfig b/drivers/net/dsa/microchip/Kconfig
index c9e2a8989556..f329cca934ee 100644
--- a/drivers/net/dsa/microchip/Kconfig
+++ b/drivers/net/dsa/microchip/Kconfig
@@ -3,6 +3,18 @@ config NET_DSA_MICROCHIP_KSZ_COMMON
select NET_DSA_TAG_KSZ
tristate
+config NET_DSA_MICROCHIP_LAN937X
+ tristate "Microchip LAN937X series SPI connected switch support"
+ depends on NET_DSA && SPI
+ select NET_DSA_MICROCHIP_KSZ_COMMON
+ select REGMAP_SPI
+ help
+ This driver adds support for Microchip LAN937X series
+ switch chips.
+
+ Select to enable support for registering switches configured
+ through SPI.
+
menuconfig NET_DSA_MICROCHIP_KSZ9477
tristate "Microchip KSZ9477 series switch support"
depends on NET_DSA
diff --git a/drivers/net/dsa/microchip/Makefile b/drivers/net/dsa/microchip/Makefile
index 2a03b21a3386..28d8eb62a795 100644
--- a/drivers/net/dsa/microchip/Makefile
+++ b/drivers/net/dsa/microchip/Makefile
@@ -6,3 +6,8 @@ obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ9477_SPI) += ksz9477_spi.o
obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ8795) += ksz8795.o
obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ8795_SPI) += ksz8795_spi.o
obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ8863_SMI) += ksz8863_smi.o
+
+obj-$(CONFIG_NET_DSA_MICROCHIP_LAN937X) += lan937x.o
+lan937x-objs := lan937x_dev.o
+lan937x-objs += lan937x_main.o
+lan937x-objs += lan937x_spi.o
diff --git a/drivers/net/dsa/microchip/ksz_common.h b/drivers/net/dsa/microchip/ksz_common.h
index 485d4a948c38..372170571088 100644
--- a/drivers/net/dsa/microchip/ksz_common.h
+++ b/drivers/net/dsa/microchip/ksz_common.h
@@ -42,6 +42,8 @@ struct ksz_port {
struct ksz_port_mib mib;
phy_interface_t interface;
u16 max_frame;
+ u32 rgmii_tx_val;
+ u32 rgmii_rx_val;
};
struct ksz_device {
@@ -148,6 +150,9 @@ void ksz_switch_remove(struct ksz_device *dev);
int ksz8_switch_register(struct ksz_device *dev);
int ksz9477_switch_register(struct ksz_device *dev);
+int lan937x_switch_register(struct ksz_device *dev);
+
+int lan937x_check_device_id(struct ksz_device *dev);
void ksz_update_port_member(struct ksz_device *dev, int port);
void ksz_init_mib_timer(struct ksz_device *dev);
diff --git a/drivers/net/dsa/microchip/lan937x_dev.c b/drivers/net/dsa/microchip/lan937x_dev.c
new file mode 100644
index 000000000000..784a24d0aa08
--- /dev/null
+++ b/drivers/net/dsa/microchip/lan937x_dev.c
@@ -0,0 +1,631 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Microchip lan937x dev ops functions
+ * Copyright (C) 2019-2021 Microchip Technology Inc.
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/iopoll.h>
+#include <linux/of_mdio.h>
+#include <linux/platform_data/microchip-ksz.h>
+#include <linux/phy.h>
+#include <linux/if_bridge.h>
+#include <net/dsa.h>
+#include <net/switchdev.h>
+
+#include "lan937x_reg.h"
+#include "ksz_common.h"
+#include "lan937x_dev.h"
+
+const struct mib_names lan937x_mib_names[] = {
+ { 0x00, "rx_hi" },
+ { 0x01, "rx_undersize" },
+ { 0x02, "rx_fragments" },
+ { 0x03, "rx_oversize" },
+ { 0x04, "rx_jabbers" },
+ { 0x05, "rx_symbol_err" },
+ { 0x06, "rx_crc_err" },
+ { 0x07, "rx_align_err" },
+ { 0x08, "rx_mac_ctrl" },
+ { 0x09, "rx_pause" },
+ { 0x0A, "rx_bcast" },
+ { 0x0B, "rx_mcast" },
+ { 0x0C, "rx_ucast" },
+ { 0x0D, "rx_64_or_less" },
+ { 0x0E, "rx_65_127" },
+ { 0x0F, "rx_128_255" },
+ { 0x10, "rx_256_511" },
+ { 0x11, "rx_512_1023" },
+ { 0x12, "rx_1024_1522" },
+ { 0x13, "rx_1523_2000" },
+ { 0x14, "rx_2001" },
+ { 0x15, "tx_hi" },
+ { 0x16, "tx_late_col" },
+ { 0x17, "tx_pause" },
+ { 0x18, "tx_bcast" },
+ { 0x19, "tx_mcast" },
+ { 0x1A, "tx_ucast" },
+ { 0x1B, "tx_deferred" },
+ { 0x1C, "tx_total_col" },
+ { 0x1D, "tx_exc_col" },
+ { 0x1E, "tx_single_col" },
+ { 0x1F, "tx_mult_col" },
+ { 0x80, "rx_total" },
+ { 0x81, "tx_total" },
+ { 0x82, "rx_discards" },
+ { 0x83, "tx_discards" },
+};
+
+int lan937x_cfg(struct ksz_device *dev, u32 addr, u8 bits, bool set)
+{
+ return regmap_update_bits(dev->regmap[0], addr, bits, set ? bits : 0);
+}
+
+int lan937x_port_cfg(struct ksz_device *dev, int port, int offset, u8 bits,
+ bool set)
+{
+ return regmap_update_bits(dev->regmap[0], PORT_CTRL_ADDR(port, offset),
+ bits, set ? bits : 0);
+}
+
+int lan937x_pread8(struct ksz_device *dev, int port, int offset, u8 *data)
+{
+ return ksz_read8(dev, PORT_CTRL_ADDR(port, offset), data);
+}
+
+int lan937x_pread16(struct ksz_device *dev, int port, int offset, u16 *data)
+{
+ return ksz_read16(dev, PORT_CTRL_ADDR(port, offset), data);
+}
+
+int lan937x_pread32(struct ksz_device *dev, int port, int offset, u32 *data)
+{
+ return ksz_read32(dev, PORT_CTRL_ADDR(port, offset), data);
+}
+
+int lan937x_pwrite8(struct ksz_device *dev, int port, int offset, u8 data)
+{
+ return ksz_write8(dev, PORT_CTRL_ADDR(port, offset), data);
+}
+
+int lan937x_pwrite16(struct ksz_device *dev, int port, int offset, u16 data)
+{
+ return ksz_write16(dev, PORT_CTRL_ADDR(port, offset), data);
+}
+
+int lan937x_pwrite32(struct ksz_device *dev, int port, int offset, u32 data)
+{
+ return ksz_write32(dev, PORT_CTRL_ADDR(port, offset), data);
+}
+
+void lan937x_cfg_port_member(struct ksz_device *dev, int port, u8 member)
+{
+ lan937x_pwrite32(dev, port, REG_PORT_VLAN_MEMBERSHIP__4, member);
+}
+
+static void lan937x_flush_dyn_mac_table(struct ksz_device *dev, int port)
+{
+ unsigned int value;
+ u8 data;
+
+ regmap_update_bits(dev->regmap[0], REG_SW_LUE_CTRL_2,
+ SW_FLUSH_OPTION_M << SW_FLUSH_OPTION_S,
+ SW_FLUSH_OPTION_DYN_MAC << SW_FLUSH_OPTION_S);
+
+ if (port < dev->port_cnt) {
+ /* flush individual port */
+ lan937x_pread8(dev, port, P_STP_CTRL, &data);
+ if (!(data & PORT_LEARN_DISABLE))
+ lan937x_pwrite8(dev, port, P_STP_CTRL,
+ (data | PORT_LEARN_DISABLE));
+ lan937x_cfg(dev, S_FLUSH_TABLE_CTRL, SW_FLUSH_DYN_MAC_TABLE,
+ true);
+
+ regmap_read_poll_timeout(dev->regmap[0], S_FLUSH_TABLE_CTRL,
+ value,
+ !(value & SW_FLUSH_DYN_MAC_TABLE), 10,
+ 1000);
+
+ lan937x_pwrite8(dev, port, P_STP_CTRL, data);
+ } else {
+ /* flush all */
+ lan937x_cfg(dev, S_FLUSH_TABLE_CTRL, SW_FLUSH_STP_TABLE, true);
+ }
+}
+
+static void lan937x_r_mib_cnt(struct ksz_device *dev, int port, u16 addr,
+ u64 *cnt)
+{
+ unsigned int val;
+ u32 data;
+ int ret;
+
+ /* Enable MIB Counter read */
+ data = MIB_COUNTER_READ;
+ data |= (addr << MIB_COUNTER_INDEX_S);
+ lan937x_pwrite32(dev, port, REG_PORT_MIB_CTRL_STAT, data);
+
+ ret = regmap_read_poll_timeout(dev->regmap[2],
+ PORT_CTRL_ADDR(port,
+ REG_PORT_MIB_CTRL_STAT),
+ val, !(val & MIB_COUNTER_READ),
+ 10, 1000);
+ if (ret) {
+ dev_err(dev->dev, "Failed to get MIB\n");
+ return;
+ }
+
+ /* count resets upon read */
+ lan937x_pread32(dev, port, REG_PORT_MIB_DATA, &data);
+ *cnt += data;
+}
+
+void lan937x_r_mib_pkt(struct ksz_device *dev, int port, u16 addr,
+ u64 *dropped, u64 *cnt)
+{
+ addr = lan937x_mib_names[addr].index;
+ lan937x_r_mib_cnt(dev, port, addr, cnt);
+}
+
+static void lan937x_r_mib_stats64(struct ksz_device *dev, int port)
+{
+ struct ksz_port_mib *mib = &dev->ports[port].mib;
+ struct rtnl_link_stats64 *s;
+ u64 *ctr = mib->counters;
+
+ s = &mib->stats64;
+ spin_lock(&mib->stats64_lock);
+
+ s->rx_packets = ctr[lan937x_mib_rx_mcast] +
+ ctr[lan937x_mib_rx_bcast] +
+ ctr[lan937x_mib_rx_ucast] +
+ ctr[lan937x_mib_rx_pause];
+
+ s->tx_packets = ctr[lan937x_mib_tx_mcast] +
+ ctr[lan937x_mib_tx_bcast] +
+ ctr[lan937x_mib_tx_ucast] +
+ ctr[lan937x_mib_tx_pause];
+
+ s->rx_bytes = ctr[lan937x_mib_rx_total];
+ s->tx_bytes = ctr[lan937x_mib_tx_total];
+
+ s->rx_errors = ctr[lan937x_mib_rx_fragments] +
+ ctr[lan937x_mib_rx_jabbers] +
+ ctr[lan937x_mib_rx_sym_err] +
+ ctr[lan937x_mib_rx_align_err] +
+ ctr[lan937x_mib_rx_crc_err];
+
+ s->tx_errors = ctr[lan937x_mib_tx_exc_col] +
+ ctr[lan937x_mib_tx_late_col];
+
+ s->rx_dropped = ctr[lan937x_mib_rx_discard];
+ s->tx_dropped = ctr[lan937x_mib_tx_discard];
+ s->multicast = ctr[lan937x_mib_rx_mcast];
+
+ s->collisions = ctr[lan937x_mib_tx_late_col] +
+ ctr[lan937x_mib_tx_single_col] +
+ ctr[lan937x_mib_tx_mult_col];
+
+ s->rx_length_errors = ctr[lan937x_mib_rx_fragments] +
+ ctr[lan937x_mib_rx_jabbers];
+
+ s->rx_crc_errors = ctr[lan937x_mib_rx_crc_err];
+ s->rx_frame_errors = ctr[lan937x_mib_rx_align_err];
+ s->tx_aborted_errors = ctr[lan937x_mib_tx_exc_col];
+ s->tx_window_errors = ctr[lan937x_mib_tx_late_col];
+
+ spin_unlock(&mib->stats64_lock);
+}
+
+static void lan937x_port_init_cnt(struct ksz_device *dev, int port)
+{
+ struct ksz_port_mib *mib = &dev->ports[port].mib;
+
+ /* flush all enabled port MIB counters */
+ mutex_lock(&mib->cnt_mutex);
+ lan937x_pwrite32(dev, port, REG_PORT_MIB_CTRL_STAT,
+ MIB_COUNTER_FLUSH_FREEZE);
+ ksz_write8(dev, REG_SW_MAC_CTRL_6, SW_MIB_COUNTER_FLUSH);
+ lan937x_pwrite32(dev, port, REG_PORT_MIB_CTRL_STAT, 0);
+ mutex_unlock(&mib->cnt_mutex);
+}
+
+int lan937x_reset_switch(struct ksz_device *dev)
+{
+ u32 data32;
+ u8 data8;
+ int ret;
+
+ /* reset switch */
+ ret = lan937x_cfg(dev, REG_SW_OPERATION, SW_RESET, true);
+ if (ret < 0)
+ return ret;
+
+ ret = ksz_read8(dev, REG_SW_LUE_CTRL_1, &data8);
+ if (ret < 0)
+ return ret;
+
+ /* Enable Auto Aging */
+ ret = ksz_write8(dev, REG_SW_LUE_CTRL_1, data8 | SW_LINK_AUTO_AGING);
+ if (ret < 0)
+ return ret;
+
+ /* disable interrupts */
+ ret = ksz_write32(dev, REG_SW_INT_MASK__4, SWITCH_INT_MASK);
+ if (ret < 0)
+ return ret;
+
+ ret = ksz_write32(dev, REG_SW_PORT_INT_MASK__4, 0xFF);
+ if (ret < 0)
+ return ret;
+
+ return ksz_read32(dev, REG_SW_PORT_INT_STATUS__4, &data32);
+}
+
+static int lan937x_switch_detect(struct ksz_device *dev)
+{
+ u32 id32;
+ int ret;
+
+ /* Read Chip ID */
+ ret = ksz_read32(dev, REG_CHIP_ID0__1, &id32);
+ if (ret < 0)
+ return ret;
+
+ if (id32 != 0 && id32 != 0xffffffff) {
+ dev->chip_id = id32;
+ dev_info(dev->dev, "Chip ID: 0x%x", id32);
+ ret = 0;
+ } else {
+ ret = -EINVAL;
+ }
+
+ return ret;
+}
+
+static void lan937x_switch_exit(struct ksz_device *dev)
+{
+ lan937x_reset_switch(dev);
+}
+
+int lan937x_enable_spi_indirect_access(struct ksz_device *dev)
+{
+ u16 data16;
+ u8 data8;
+ int ret;
+
+ ret = ksz_read8(dev, REG_GLOBAL_CTRL_0, &data8);
+ if (ret < 0)
+ return ret;
+
+ /* Check if PHY register is blocked */
+ if (data8 & SW_PHY_REG_BLOCK) {
+ /* Enable Phy access through SPI */
+ data8 &= ~SW_PHY_REG_BLOCK;
+
+ ret = ksz_write8(dev, REG_GLOBAL_CTRL_0, data8);
+ if (ret < 0)
+ return ret;
+ }
+
+ ret = ksz_read16(dev, REG_VPHY_SPECIAL_CTRL__2, &data16);
+ if (ret < 0)
+ return ret;
+
+ /* Allow SPI access */
+ data16 |= VPHY_SPI_INDIRECT_ENABLE;
+
+ return ksz_write16(dev, REG_VPHY_SPECIAL_CTRL__2, data16);
+}
+
+static u32 lan937x_get_port_addr(int port, int offset)
+{
+ return PORT_CTRL_ADDR(port, offset);
+}
+
+bool lan937x_is_internal_phy_port(struct ksz_device *dev, int port)
+{
+ /* Check if the port is RGMII */
+ if (port == LAN937X_RGMII_1_PORT || port == LAN937X_RGMII_2_PORT)
+ return false;
+
+ /* Check if the port is SGMII */
+ if (port == LAN937X_SGMII_PORT &&
+ GET_CHIP_ID_LSB(dev->chip_id) == CHIP_ID_73)
+ return false;
+
+ return true;
+}
+
+bool lan937x_is_rgmii_port(struct ksz_device *dev, int port)
+{
+ /* Check if the port is RGMII */
+ if (port == LAN937X_RGMII_1_PORT || port == LAN937X_RGMII_2_PORT)
+ return true;
+
+ return false;
+}
+
+bool lan937x_is_internal_base_tx_phy_port(struct ksz_device *dev, int port)
+{
+ /* Check if the port is internal tx phy port */
+ if (lan937x_is_internal_phy_port(dev, port) &&
+ port == LAN937X_TXPHY_PORT)
+ if ((GET_CHIP_ID_LSB(dev->chip_id) == CHIP_ID_71) ||
+ (GET_CHIP_ID_LSB(dev->chip_id) == CHIP_ID_72))
+ return true;
+
+ return false;
+}
+
+bool lan937x_is_internal_base_t1_phy_port(struct ksz_device *dev, int port)
+{
+ /* Check if the port is internal t1 phy port */
+ if (lan937x_is_internal_phy_port(dev, port) &&
+ !lan937x_is_internal_base_tx_phy_port(dev, port))
+ return true;
+
+ return false;
+}
+
+static int lan937x_vphy_ind_addr_wr(struct ksz_device *dev, int addr, int reg)
+{
+ u16 temp, addr_base;
+
+ if (lan937x_is_internal_base_tx_phy_port(dev, addr))
+ addr_base = REG_PORT_TX_PHY_CTRL_BASE;
+ else
+ addr_base = REG_PORT_T1_PHY_CTRL_BASE;
+
+ /* get register address based on the logical port */
+ temp = PORT_CTRL_ADDR(addr, (addr_base + (reg << 2)));
+
+ return ksz_write16(dev, REG_VPHY_IND_ADDR__2, temp);
+}
+
+int lan937x_internal_phy_write(struct ksz_device *dev, int addr, int reg,
+ u16 val)
+{
+ unsigned int value;
+ int ret;
+
+ /* Check for internal phy port */
+ if (!lan937x_is_internal_phy_port(dev, addr))
+ return -EOPNOTSUPP;
+
+ ret = lan937x_vphy_ind_addr_wr(dev, addr, reg);
+ if (ret < 0)
+ return ret;
+
+ /* Write the data to be written to the VPHY reg */
+ ret = ksz_write16(dev, REG_VPHY_IND_DATA__2, val);
+ if (ret < 0)
+ return ret;
+
+ /* Write the Write En and Busy bit */
+ ret = ksz_write16(dev, REG_VPHY_IND_CTRL__2,
+ (VPHY_IND_WRITE | VPHY_IND_BUSY));
+ if (ret < 0)
+ return ret;
+
+ ret = regmap_read_poll_timeout(dev->regmap[1], REG_VPHY_IND_CTRL__2,
+ value, !(value & VPHY_IND_BUSY), 10,
+ 1000);
+ if (ret < 0) {
+ dev_err(dev->dev, "Failed to write phy register\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+int lan937x_internal_phy_read(struct ksz_device *dev, int addr, int reg,
+ u16 *val)
+{
+ unsigned int value;
+ int ret;
+
+ /* Check for internal phy port, return 0xffff for non-existent phy */
+ if (!lan937x_is_internal_phy_port(dev, addr))
+ return 0xffff;
+
+ ret = lan937x_vphy_ind_addr_wr(dev, addr, reg);
+ if (ret < 0)
+ return ret;
+
+ /* Write Read and Busy bit to start the transaction */
+ ret = ksz_write16(dev, REG_VPHY_IND_CTRL__2, VPHY_IND_BUSY);
+ if (ret < 0)
+ return ret;
+
+ ret = regmap_read_poll_timeout(dev->regmap[1], REG_VPHY_IND_CTRL__2,
+ value, !(value & VPHY_IND_BUSY), 10,
+ 1000);
+ if (ret < 0) {
+ dev_err(dev->dev, "Failed to read phy register\n");
+ return ret;
+ }
+
+ /* Read the VPHY register which has the PHY data */
+ return ksz_read16(dev, REG_VPHY_IND_DATA__2, val);
+}
+
+void lan937x_port_setup(struct ksz_device *dev, int port, bool cpu_port)
+{
+ struct dsa_switch *ds = dev->ds;
+ u8 member;
+
+ /* enable tag tail for host port */
+ if (cpu_port)
+ lan937x_port_cfg(dev, port, REG_PORT_CTRL_0,
+ PORT_TAIL_TAG_ENABLE, true);
+
+ /* disable frame check length field */
+ lan937x_port_cfg(dev, port, REG_PORT_MAC_CTRL_0, PORT_FR_CHK_LENGTH,
+ false);
+
+ /* set back pressure for half duplex */
+ lan937x_port_cfg(dev, port, REG_PORT_MAC_CTRL_1, PORT_BACK_PRESSURE,
+ true);
+
+ /* enable 802.1p priority */
+ lan937x_port_cfg(dev, port, P_PRIO_CTRL, PORT_802_1P_PRIO_ENABLE, true);
+
+ if (!lan937x_is_internal_phy_port(dev, port))
+ lan937x_port_cfg(dev, port, REG_PORT_XMII_CTRL_0,
+ PORT_TX_FLOW_CTRL | PORT_RX_FLOW_CTRL,
+ true);
+
+ if (cpu_port)
+ member = dsa_user_ports(ds);
+ else
+ member = BIT(dsa_upstream_port(ds, port));
+
+ lan937x_cfg_port_member(dev, port, member);
+}
+
+static int lan937x_sw_mdio_read(struct mii_bus *bus, int addr, int regnum)
+{
+ struct ksz_device *dev = bus->priv;
+ u16 val;
+ int ret;
+
+ if (regnum & MII_ADDR_C45)
+ return -EOPNOTSUPP;
+
+ ret = lan937x_internal_phy_read(dev, addr, regnum, &val);
+ if (ret < 0)
+ return ret;
+
+ return val;
+}
+
+static int lan937x_sw_mdio_write(struct mii_bus *bus, int addr, int regnum,
+ u16 val)
+{
+ struct ksz_device *dev = bus->priv;
+
+ if (regnum & MII_ADDR_C45)
+ return -EOPNOTSUPP;
+
+ return lan937x_internal_phy_write(dev, addr, regnum, val);
+}
+
+static int lan937x_mdio_register(struct ksz_device *dev)
+{
+ struct dsa_switch *ds = dev->ds;
+ struct device_node *mdio_np;
+ struct mii_bus *bus;
+ int ret;
+
+ mdio_np = of_get_child_by_name(dev->dev->of_node, "mdio");
+ if (!mdio_np) {
+ dev_err(ds->dev, "no MDIO bus node\n");
+ return -ENODEV;
+ }
+
+ bus = devm_mdiobus_alloc(ds->dev);
+ if (!bus) {
+ of_node_put(mdio_np);
+ return -ENOMEM;
+ }
+
+ bus->priv = dev;
+ bus->read = lan937x_sw_mdio_read;
+ bus->write = lan937x_sw_mdio_write;
+ bus->name = "lan937x slave smi";
+ snprintf(bus->id, MII_BUS_ID_SIZE, "SMI-%d", ds->index);
+ bus->parent = ds->dev;
+ bus->phy_mask = ~ds->phys_mii_mask;
+
+ ds->slave_mii_bus = bus;
+
+ ret = devm_of_mdiobus_register(ds->dev, bus, mdio_np);
+ if (ret) {
+ dev_err(ds->dev, "unable to register MDIO bus %s\n",
+ bus->id);
+ }
+
+ of_node_put(mdio_np);
+
+ return ret;
+}
+
+static int lan937x_switch_init(struct ksz_device *dev)
+{
+ int i, ret;
+
+ dev->ds->ops = &lan937x_switch_ops;
+
+ /* Check device tree */
+ ret = lan937x_check_device_id(dev);
+ if (ret < 0)
+ return ret;
+
+ dev->port_mask = (1 << dev->port_cnt) - 1;
+
+ dev->reg_mib_cnt = SWITCH_COUNTER_NUM;
+ dev->mib_cnt = ARRAY_SIZE(lan937x_mib_names);
+
+ dev->ports = devm_kzalloc(dev->dev,
+ dev->port_cnt * sizeof(struct ksz_port),
+ GFP_KERNEL);
+ if (!dev->ports)
+ return -ENOMEM;
+
+ for (i = 0; i < dev->port_cnt; i++) {
+ spin_lock_init(&dev->ports[i].mib.stats64_lock);
+ mutex_init(&dev->ports[i].mib.cnt_mutex);
+ dev->ports[i].mib.counters =
+ devm_kzalloc(dev->dev,
+ sizeof(u64) * (dev->mib_cnt + 1),
+ GFP_KERNEL);
+
+ if (!dev->ports[i].mib.counters)
+ return -ENOMEM;
+ }
+
+ /* set the real number of ports */
+ dev->ds->num_ports = dev->port_cnt;
+ return 0;
+}
+
+static int lan937x_init(struct ksz_device *dev)
+{
+ int ret;
+
+ ret = lan937x_switch_init(dev);
+ if (ret < 0) {
+ dev_err(dev->dev, "failed to initialize the switch");
+ return ret;
+ }
+
+ /* enable Indirect Access from SPI to the VPHY registers */
+ ret = lan937x_enable_spi_indirect_access(dev);
+ if (ret < 0) {
+ dev_err(dev->dev, "failed to enable spi indirect access");
+ return ret;
+ }
+
+ ret = lan937x_mdio_register(dev);
+ if (ret < 0) {
+ dev_err(dev->dev, "failed to register the mdio");
+ return ret;
+ }
+
+ return 0;
+}
+
+const struct ksz_dev_ops lan937x_dev_ops = {
+ .get_port_addr = lan937x_get_port_addr,
+ .cfg_port_member = lan937x_cfg_port_member,
+ .flush_dyn_mac_table = lan937x_flush_dyn_mac_table,
+ .port_setup = lan937x_port_setup,
+ .r_mib_cnt = lan937x_r_mib_cnt,
+ .r_mib_pkt = lan937x_r_mib_pkt,
+ .port_init_cnt = lan937x_port_init_cnt,
+ .r_mib_stat64 = lan937x_r_mib_stats64,
+ .shutdown = lan937x_reset_switch,
+ .detect = lan937x_switch_detect,
+ .init = lan937x_init,
+ .exit = lan937x_switch_exit,
+};
diff --git a/drivers/net/dsa/microchip/lan937x_dev.h b/drivers/net/dsa/microchip/lan937x_dev.h
new file mode 100644
index 000000000000..eba36912969a
--- /dev/null
+++ b/drivers/net/dsa/microchip/lan937x_dev.h
@@ -0,0 +1,117 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Microchip lan937x dev ops headers
+ * Copyright (C) 2019-2021 Microchip Technology Inc.
+ */
+
+#ifndef __LAN937X_CFG_H
+#define __LAN937X_CFG_H
+
+int lan937x_cfg(struct ksz_device *dev, u32 addr, u8 bits, bool set);
+int lan937x_port_cfg(struct ksz_device *dev, int port, int offset,
+ u8 bits, bool set);
+int lan937x_pread8(struct ksz_device *dev, int port, int offset,
+ u8 *data);
+int lan937x_pread16(struct ksz_device *dev, int port, int offset,
+ u16 *data);
+int lan937x_pread32(struct ksz_device *dev, int port, int offset,
+ u32 *data);
+int lan937x_pwrite8(struct ksz_device *dev, int port,
+ int offset, u8 data);
+int lan937x_pwrite16(struct ksz_device *dev, int port,
+ int offset, u16 data);
+int lan937x_pwrite32(struct ksz_device *dev, int port,
+ int offset, u32 data);
+int lan937x_internal_phy_write(struct ksz_device *dev, int addr,
+ int reg, u16 val);
+int lan937x_internal_phy_read(struct ksz_device *dev, int addr,
+ int reg, u16 *val);
+bool lan937x_is_internal_phy_port(struct ksz_device *dev, int port);
+bool lan937x_is_internal_base_tx_phy_port(struct ksz_device *dev, int port);
+bool lan937x_is_internal_base_t1_phy_port(struct ksz_device *dev, int port);
+bool lan937x_is_rgmii_port(struct ksz_device *dev, int port);
+int lan937x_reset_switch(struct ksz_device *dev);
+void lan937x_cfg_port_member(struct ksz_device *dev, int port,
+ u8 member);
+void lan937x_port_setup(struct ksz_device *dev, int port, bool cpu_port);
+int lan937x_enable_spi_indirect_access(struct ksz_device *dev);
+void lan937x_r_mib_pkt(struct ksz_device *dev, int port, u16 addr,
+ u64 *dropped, u64 *cnt);
+
+struct mib_names {
+ int index;
+ char string[ETH_GSTRING_LEN];
+};
+
+enum lan937x_mib_list {
+ lan937x_mib_rx_hi_pri_byte = 0,
+ lan937x_mib_rx_undersize,
+ lan937x_mib_rx_fragments,
+ lan937x_mib_rx_oversize,
+ lan937x_mib_rx_jabbers,
+ lan937x_mib_rx_sym_err,
+ lan937x_mib_rx_crc_err,
+ lan937x_mib_rx_align_err,
+ lan937x_mib_rx_mac_ctrl,
+ lan937x_mib_rx_pause,
+ lan937x_mib_rx_bcast,
+ lan937x_mib_rx_mcast,
+ lan937x_mib_rx_ucast,
+ lan937x_mib_rx_64_or_less,
+ lan937x_mib_rx_65_127,
+ lan937x_mib_rx_128_255,
+ lan937x_mib_rx_256_511,
+ lan937x_mib_rx_512_1023,
+ lan937x_mib_rx_1024_1522,
+ lan937x_mib_rx_1523_2000,
+ lan937x_mib_rx_2001,
+ lan937x_mib_tx_hi_pri_byte,
+ lan937x_mib_tx_late_col,
+ lan937x_mib_tx_pause,
+ lan937x_mib_tx_bcast,
+ lan937x_mib_tx_mcast,
+ lan937x_mib_tx_ucast,
+ lan937x_mib_tx_deferred,
+ lan937x_mib_tx_total_col,
+ lan937x_mib_tx_exc_col,
+ lan937x_mib_tx_single_col,
+ lan937x_mib_tx_mult_col,
+ lan937x_mib_rx_total,
+ lan937x_mib_tx_total,
+ lan937x_mib_rx_discard,
+ lan937x_mib_tx_discard,
+};
+
+struct lan_alu_struct {
+ /* entry 1 */
+ u32 is_static:1;
+ u32 is_src_filter:1;
+ u32 is_dst_filter:1;
+ u32 prio_age:3;
+ u32 _reserv_0_1:23;
+ u32 mstp:3;
+ /* entry 2 */
+ u32 is_override:1;
+ u32 is_use_fid:1;
+ u32 _reserv_1_1:22;
+ u32 port_forward:8;
+ /* entry 3 & 4*/
+ u32 _reserv_2_1:9;
+ u32 fid:7;
+ u8 mac[ETH_ALEN];
+};
+
+struct lan937x_vlan {
+ /* entry 1 */
+ bool valid;
+ u8 fid;
+ /* entry 2 */
+ u32 untag_prtmap;
+ /* entry 3 */
+ u32 fwd_map;
+};
+
+extern const struct dsa_switch_ops lan937x_switch_ops;
+extern const struct ksz_dev_ops lan937x_dev_ops;
+extern const struct mib_names lan937x_mib_names[];
+
+#endif
diff --git a/drivers/net/dsa/microchip/lan937x_main.c b/drivers/net/dsa/microchip/lan937x_main.c
new file mode 100644
index 000000000000..b5164be297c8
--- /dev/null
+++ b/drivers/net/dsa/microchip/lan937x_main.c
@@ -0,0 +1,320 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Microchip LAN937X switch driver main logic
+ * Copyright (C) 2019-2021 Microchip Technology Inc.
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/iopoll.h>
+#include <linux/phy.h>
+#include <linux/of_net.h>
+#include <linux/if_bridge.h>
+#include <linux/if_vlan.h>
+#include <linux/math.h>
+#include <net/dsa.h>
+#include <net/switchdev.h>
+
+#include "lan937x_reg.h"
+#include "ksz_common.h"
+#include "lan937x_dev.h"
+
+static enum dsa_tag_protocol lan937x_get_tag_protocol(struct dsa_switch *ds,
+ int port,
+ enum dsa_tag_protocol mp)
+{
+ return DSA_TAG_PROTO_LAN937X_VALUE;
+}
+
+static int lan937x_phy_read16(struct dsa_switch *ds, int addr, int reg)
+{
+ struct ksz_device *dev = ds->priv;
+ u16 val;
+ int ret;
+
+ ret = lan937x_internal_phy_read(dev, addr, reg, &val);
+ if (ret < 0)
+ return ret;
+
+ return val;
+}
+
+static int lan937x_phy_write16(struct dsa_switch *ds, int addr, int reg,
+ u16 val)
+{
+ struct ksz_device *dev = ds->priv;
+
+ return lan937x_internal_phy_write(dev, addr, reg, val);
+}
+
+static void lan937x_port_stp_state_set(struct dsa_switch *ds, int port,
+ u8 state)
+{
+ struct ksz_device *dev = ds->priv;
+ struct ksz_port *p;
+ u8 data;
+
+ lan937x_pread8(dev, port, P_STP_CTRL, &data);
+ data &= ~(PORT_TX_ENABLE | PORT_RX_ENABLE | PORT_LEARN_DISABLE);
+
+ switch (state) {
+ case BR_STATE_DISABLED:
+ data |= PORT_LEARN_DISABLE;
+ break;
+ case BR_STATE_LISTENING:
+ data |= (PORT_RX_ENABLE | PORT_LEARN_DISABLE);
+ break;
+ case BR_STATE_LEARNING:
+ data |= PORT_RX_ENABLE;
+ break;
+ case BR_STATE_FORWARDING:
+ data |= (PORT_TX_ENABLE | PORT_RX_ENABLE);
+ break;
+ case BR_STATE_BLOCKING:
+ data |= PORT_LEARN_DISABLE;
+ break;
+ default:
+ dev_err(ds->dev, "invalid STP state: %d\n", state);
+ return;
+ }
+
+ lan937x_pwrite8(dev, port, P_STP_CTRL, data);
+
+ p = &dev->ports[port];
+ p->stp_state = state;
+
+ ksz_update_port_member(dev, port);
+}
+
+static void lan937x_config_cpu_port(struct dsa_switch *ds)
+{
+ struct ksz_device *dev = ds->priv;
+ int i;
+
+ ds->num_ports = dev->port_cnt;
+
+ for (i = 0; i < dev->port_cnt; i++) {
+ if (dsa_is_cpu_port(ds, i) && (dev->cpu_ports & (1 << i))) {
+ dev->cpu_port = i;
+
+ /* enable cpu port */
+ lan937x_port_setup(dev, i, true);
+ }
+ }
+
+ for (i = 0; i < dev->port_cnt; i++) {
+ if (i == dev->cpu_port)
+ continue;
+
+ lan937x_port_stp_state_set(ds, i, BR_STATE_DISABLED);
+ }
+}
+
+static int lan937x_set_rgmii_delay(struct ksz_device *dev, int port,
+ u32 val, bool is_tx)
+{
+ struct ksz_port *p = &dev->ports[port];
+ const char *name[2] = { "rx", "tx" };
+
+ /* alert if delay is out of range */
+ if (val != 0 && val != 2000) {
+ dev_err(dev->dev,
+ "rgmii %s delay %d is out of range for the port %d\n",
+ name[is_tx], val, port);
+ return -EOPNOTSUPP;
+ }
+
+ /* get the valid value & store it for delay calculation */
+ if (is_tx)
+ p->rgmii_tx_val = val;
+ else
+ p->rgmii_rx_val = val;
+
+ return 0;
+}
+
+static int lan937x_parse_dt_rgmii_delay(struct ksz_device *dev)
+{
+ struct device_node *ports, *port;
+ int err, p;
+ u32 val;
+
+ ports = of_get_child_by_name(dev->dev->of_node, "ports");
+ if (!ports)
+ ports = of_get_child_by_name(dev->dev->of_node,
+ "ethernet-ports");
+ if (!ports) {
+ dev_err(dev->dev, "no ports child node found\n");
+ return -EINVAL;
+ }
+
+ for_each_available_child_of_node(ports, port) {
+ err = of_property_read_u32(port, "reg", &p);
+ if (err) {
+ dev_err(dev->dev, "Port num not defined in the DT, \"reg\" property\n");
+ of_node_put(ports);
+ of_node_put(port);
+ return err;
+ }
+
+ /* skip for internal ports */
+ if (lan937x_is_internal_phy_port(dev, p))
+ continue;
+
+ if (of_property_read_u32(port, "rx-internal-delay-ps", &val))
+ val = 0;
+
+ err = lan937x_set_rgmii_delay(dev, p, val, false);
+ if (err)
+ break;
+
+ if (of_property_read_u32(port, "tx-internal-delay-ps", &val))
+ val = 0;
+
+ err = lan937x_set_rgmii_delay(dev, p, val, true);
+ if (err)
+ break;
+ }
+
+ of_node_put(ports);
+ return err;
+}
+
+static int lan937x_setup(struct dsa_switch *ds)
+{
+ struct ksz_device *dev = ds->priv;
+ u32 data32;
+ u8 data8;
+ int ret;
+
+ ret = lan937x_reset_switch(dev);
+ if (ret < 0)
+ return ret;
+
+ ret = ksz_read8(dev, REG_SW_LUE_CTRL_1, &data8);
+ if (ret < 0)
+ return ret;
+
+ /* Enable Auto Aging */
+ ret = ksz_write8(dev, REG_SW_LUE_CTRL_1, data8 | SW_LINK_AUTO_AGING);
+ if (ret < 0)
+ return ret;
+
+ /* disable interrupts */
+ ret = ksz_write32(dev, REG_SW_INT_MASK__4, SWITCH_INT_MASK);
+ if (ret < 0)
+ return ret;
+
+ ret = ksz_write32(dev, REG_SW_PORT_INT_MASK__4, 0xFF);
+ if (ret < 0)
+ return ret;
+
+ /* Read interrupt status register */
+ ret = ksz_read32(dev, REG_SW_PORT_INT_STATUS__4, &data32);
+ if (ret < 0)
+ return ret;
+
+ /* Apply rgmii internal delay for the mac based on device tree */
+ ret = lan937x_parse_dt_rgmii_delay(dev);
+ if (ret < 0)
+ return ret;
+
+ /* The VLAN aware is a global setting. Mixed vlan
+ * filterings are not supported.
+ */
+ ds->vlan_filtering_is_global = true;
+
+ /* Configure cpu port */
+ lan937x_config_cpu_port(ds);
+
+ /* Enable aggressive back off for half duplex & UNH mode */
+ lan937x_cfg(dev, REG_SW_MAC_CTRL_0,
+ (SW_PAUSE_UNH_MODE | SW_NEW_BACKOFF | SW_AGGR_BACKOFF),
+ true);
+
+ /* If NO_EXC_COLLISION_DROP bit is set, the switch will not drop
+ * packets when 16 or more collisions occur
+ */
+ lan937x_cfg(dev, REG_SW_MAC_CTRL_1, NO_EXC_COLLISION_DROP, true);
+
+ /* Enable reserved multicast table */
+ lan937x_cfg(dev, REG_SW_LUE_CTRL_0, SW_RESV_MCAST_ENABLE, true);
+
+ /* enable global MIB counter freeze function */
+ lan937x_cfg(dev, REG_SW_MAC_CTRL_6, SW_MIB_COUNTER_FREEZE, true);
+
+ /* disable CLK125 & CLK25, 1: disable, 0: enable */
+ lan937x_cfg(dev, REG_SW_GLOBAL_OUTPUT_CTRL__1,
+ (SW_CLK125_ENB | SW_CLK25_ENB), true);
+
+ lan937x_enable_spi_indirect_access(dev);
+
+ /* start switch */
+ lan937x_cfg(dev, REG_SW_OPERATION, SW_START, true);
+
+ ksz_init_mib_timer(dev);
+
+ return 0;
+}
+
+static int lan937x_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
+{
+ struct ksz_device *dev = ds->priv;
+ int ret;
+
+ new_mtu += VLAN_ETH_HLEN + ETH_FCS_LEN;
+
+ if (dsa_is_cpu_port(ds, port))
+ new_mtu += LAN937X_TAG_LEN;
+
+ if (new_mtu >= FR_MIN_SIZE)
+ ret = lan937x_port_cfg(dev, port, REG_PORT_MAC_CTRL_0,
+ PORT_JUMBO_EN, true);
+ else
+ ret = lan937x_port_cfg(dev, port, REG_PORT_MAC_CTRL_0,
+ PORT_JUMBO_EN, false);
+ if (ret < 0) {
+ dev_err(ds->dev, "failed to enable jumbo\n");
+ return ret;
+ }
+
+ /* Write the frame size in PORT_MAX_FR_SIZE register */
+ ret = lan937x_pwrite16(dev, port, PORT_MAX_FR_SIZE, new_mtu);
+ if (ret < 0) {
+ dev_err(ds->dev, "failed to change the mtu\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int lan937x_get_max_mtu(struct dsa_switch *ds, int port)
+{
+ /* Frame max size is 9000 (= 0x2328) if
+ * jumbo frame support is enabled, PORT_JUMBO_EN bit will be enabled
+ * based on mtu in lan937x_change_mtu() API
+ */
+ return (FR_MAX_SIZE - VLAN_ETH_HLEN - ETH_FCS_LEN);
+}
+
+const struct dsa_switch_ops lan937x_switch_ops = {
+ .get_tag_protocol = lan937x_get_tag_protocol,
+ .setup = lan937x_setup,
+ .phy_read = lan937x_phy_read16,
+ .phy_write = lan937x_phy_write16,
+ .port_enable = ksz_enable_port,
+ .port_bridge_join = ksz_port_bridge_join,
+ .port_bridge_leave = ksz_port_bridge_leave,
+ .port_stp_state_set = lan937x_port_stp_state_set,
+ .port_fast_age = ksz_port_fast_age,
+ .port_max_mtu = lan937x_get_max_mtu,
+ .port_change_mtu = lan937x_change_mtu,
+};
+
+int lan937x_switch_register(struct ksz_device *dev)
+{
+ return ksz_switch_register(dev, &lan937x_dev_ops);
+}
+EXPORT_SYMBOL(lan937x_switch_register);
+
+MODULE_AUTHOR("Prasanna Vengateshan Varadharajan <Prasanna.Vengateshan@...rochip.com>");
+MODULE_DESCRIPTION("Microchip LAN937x Series Switch DSA Driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/dsa/microchip/lan937x_reg.h b/drivers/net/dsa/microchip/lan937x_reg.h
new file mode 100644
index 000000000000..d0de595f6c4e
--- /dev/null
+++ b/drivers/net/dsa/microchip/lan937x_reg.h
@@ -0,0 +1,688 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Microchip LAN937X switch register definitions
+ * Copyright (C) 2019-2021 Microchip Technology Inc.
+ */
+#ifndef __LAN937X_REG_H
+#define __LAN937X_REG_H
+
+/* 0 - Operation */
+#define REG_CHIP_ID0__1 0x0000
+#define REG_CHIP_ID1__1 0x0001
+#define REG_CHIP_ID2__1 0x0002
+
+#define CHIP_ID_74 0x74
+#define CHIP_ID_73 0x73
+#define CHIP_ID_72 0x72
+#define CHIP_ID_71 0x71
+#define CHIP_ID_70 0x70
+
+#define REG_CHIP_ID3__1 0x0003
+
+#define REG_GLOBAL_CTRL_0 0x0007
+
+#define SW_PHY_REG_BLOCK BIT(7)
+#define SW_FAST_MODE BIT(3)
+#define SW_FAST_MODE_OVERRIDE BIT(2)
+
+#define REG_GLOBAL_OPTIONS 0x000F
+
+#define REG_SW_INT_STATUS__4 0x0010
+#define REG_SW_INT_MASK__4 0x0014
+
+#define LUE_INT BIT(31)
+#define TRIG_TS_INT BIT(30)
+#define APB_TIMEOUT_INT BIT(29)
+#define OVER_TEMP_INT BIT(28)
+#define HSR_INT BIT(27)
+#define PIO_INT BIT(26)
+#define POR_READY_INT BIT(25)
+
+#define SWITCH_INT_MASK \
+ (LUE_INT | TRIG_TS_INT | APB_TIMEOUT_INT | OVER_TEMP_INT | HSR_INT | \
+ PIO_INT | POR_READY_INT)
+
+#define REG_SW_PORT_INT_STATUS__4 0x0018
+#define REG_SW_PORT_INT_MASK__4 0x001C
+
+/* 1 - Global */
+#define REG_SW_GLOBAL_SERIAL_CTRL_0 0x0100
+
+#define SW_LITTLE_ENDIAN BIT(4)
+#define SPI_AUTO_EDGE_DETECTION BIT(1)
+#define SPI_CLOCK_OUT_RISING_EDGE BIT(0)
+
+#define REG_SW_GLOBAL_OUTPUT_CTRL__1 0x0103
+#define SW_CLK125_ENB BIT(1)
+#define SW_CLK25_ENB BIT(0)
+
+/* 2 - PHY */
+#define REG_SW_POWER_MANAGEMENT_CTRL 0x0201
+
+/* 3 - Operation Control */
+#define REG_SW_OPERATION 0x0300
+
+#define SW_DOUBLE_TAG BIT(7)
+#define SW_OVER_TEMP_ENABLE BIT(2)
+#define SW_RESET BIT(1)
+#define SW_START BIT(0)
+
+#define REG_SW_LUE_CTRL_0 0x0310
+#define SW_VLAN_ENABLE BIT(7)
+#define SW_DROP_INVALID_VID BIT(6)
+#define SW_AGE_CNT_M 0x7
+#define SW_AGE_CNT_S 3
+#define SW_RESV_MCAST_ENABLE BIT(2)
+
+#define REG_SW_LUE_CTRL_1 0x0311
+
+#define UNICAST_LEARN_DISABLE BIT(7)
+#define SW_FLUSH_STP_TABLE BIT(5)
+#define SW_FLUSH_MSTP_TABLE BIT(4)
+#define SW_SRC_ADDR_FILTER BIT(3)
+#define SW_AGING_ENABLE BIT(2)
+#define SW_FAST_AGING BIT(1)
+#define SW_LINK_AUTO_AGING BIT(0)
+
+#define REG_SW_LUE_CTRL_2 0x0312
+
+#define SW_MID_RANGE_AGE BIT(7)
+#define SW_LINK_DOWN_FLUSH BIT(6)
+#define SW_EGRESS_VLAN_FILTER_DYN BIT(5)
+#define SW_EGRESS_VLAN_FILTER_STA BIT(4)
+#define SW_FLUSH_OPTION_M 0x3
+#define SW_FLUSH_OPTION_S 2
+#define SW_FLUSH_OPTION_DYN_MAC 1
+#define SW_FLUSH_OPTION_STA_MAC 2
+#define SW_FLUSH_OPTION_BOTH 3
+
+#define REG_SW_LUE_CTRL_3 0x0313
+#define REG_SW_AGE_PERIOD__1 0x0313
+
+#define REG_SW_LUE_INT_STATUS__1 0x0314
+#define REG_SW_LUE_INT_MASK__1 0x0315
+
+#define LEARN_FAIL_INT BIT(2)
+#define WRITE_FAIL_INT BIT(0)
+
+#define LUE_INT_MASK (LEARN_FAIL_INT | WRITE_FAIL_INT)
+
+#define REG_SW_LUE_INDEX_0__2 0x0316
+
+#define ENTRY_INDEX_M 0x0FFF
+
+#define REG_SW_LUE_INDEX_1__2 0x0318
+
+#define FAIL_INDEX_M 0x03FF
+
+#define REG_SW_LUE_INDEX_2__2 0x031A
+
+#define REG_SW_STATIC_AVAIL_ENTRY__4 0x031C
+
+#define SW_INGRESS_FILTERING_NO_LEARN BIT(15)
+#define SW_STATIC_AVAIL_CNT 0x1FF
+
+#define REG_SW_AGE_PERIOD__2 0x0320
+#define SW_AGE_PERIOD_M 0xFFF
+
+#define REG_SW_LUE_UNK_UCAST_CTRL__2 0x0322
+#define REG_SW_LUE_UNK_CTRL_0__4 0x0322
+
+#define SW_UNK_UCAST_ENABLE BIT(15)
+#define SW_UNK_PORTS_M 0xFF
+
+#define REG_SW_LUE_UNK_MCAST_CTRL__2 0x0324
+#define SW_UNK_MCAST_ENABLE BIT(15)
+
+#define REG_SW_LUE_UNK_VID_CTRL__2 0x0326
+#define SW_UNK_VID_ENABLE BIT(15)
+
+#define SW_VLAN_FLUSH_PORTS_M 0xFF
+
+#define REG_SW_STATIC_ENTRY_LIMIT__4 0x032C
+
+#define REG_SW_MAC_CTRL_0 0x0330
+#define SW_NEW_BACKOFF BIT(7)
+#define SW_PAUSE_UNH_MODE BIT(1)
+#define SW_AGGR_BACKOFF BIT(0)
+
+#define REG_SW_MAC_CTRL_1 0x0331
+#define SW_SHORT_IFG BIT(7)
+#define MULTICAST_STORM_DISABLE BIT(6)
+#define SW_BACK_PRESSURE BIT(5)
+#define FAIR_FLOW_CTRL BIT(4)
+#define NO_EXC_COLLISION_DROP BIT(3)
+#define SW_LEGAL_PACKET_DISABLE BIT(1)
+#define SW_PASS_SHORT_FRAME BIT(0)
+
+#define REG_SW_MAC_CTRL_2 0x0332
+#define SW_REPLACE_VID BIT(3)
+#define BROADCAST_STORM_RATE_HI 0x07
+
+#define REG_SW_MAC_CTRL_3 0x0333
+#define BROADCAST_STORM_RATE_LO 0xFF
+#define BR_STORM_RATE 0x07FF
+
+#define REG_SW_MAC_CTRL_4 0x0334
+#define SW_PASS_PAUSE BIT(3)
+
+#define REG_SW_MAC_CTRL_5 0x0335
+#define SW_OUT_RATE_LIMIT_QUEUE_BASED BIT(3)
+
+#define REG_SW_MAC_CTRL_6 0x0336
+#define SW_MIB_COUNTER_FLUSH BIT(7)
+#define SW_MIB_COUNTER_FREEZE BIT(6)
+
+#define REG_SW_MRI_CTRL_0 0x0370
+#define SW_IGMP_SNOOP BIT(6)
+#define SW_IPV6_MLD_OPTION BIT(3)
+#define SW_IPV6_MLD_SNOOP BIT(2)
+#define SW_MIRROR_RX_TX BIT(0)
+
+#define REG_SW_MRI_CTRL_1__4 0x0374
+#define REG_SW_MRI_CTRL_2__4 0x0378
+#define REG_SW_CLASS_D_IP_CTRL__4 0x0374
+
+#define SW_CLASS_D_IP_ENABLE BIT(31)
+
+#define REG_SW_MRI_CTRL_8 0x0378
+#define SW_RED_COLOR_S 4
+#define SW_YELLOW_COLOR_S 2
+#define SW_GREEN_COLOR_S 0
+#define SW_COLOR_M 0x3
+
+#define REG_PTP_EVENT_PRIO_CTRL 0x037C
+#define REG_PTP_GENERAL_PRIO_CTRL 0x037D
+#define PTP_PRIO_ENABLE BIT(7)
+
+#define REG_SW_QM_CTRL__4 0x0390
+#define PRIO_SCHEME_SELECT_M KS_PRIO_M
+#define PRIO_SCHEME_SELECT_S 6
+#define PRIO_MAP_3_HI 0
+#define PRIO_MAP_2_HI 2
+#define PRIO_MAP_0_LO 3
+#define UNICAST_VLAN_BOUNDARY BIT(1)
+
+#define REG_SW_EEE_QM_CTRL__2 0x03C0
+#define REG_SW_EEE_TXQ_WAIT_TIME__2 0x03C2
+
+/* 4 - */
+#define REG_SW_VLAN_ENTRY__4 0x0400
+#define VLAN_VALID BIT(31)
+#define VLAN_FORWARD_OPTION BIT(27)
+#define VLAN_PRIO_M KS_PRIO_M
+#define VLAN_PRIO_S 24
+#define VLAN_MSTP_M 0x7
+#define VLAN_MSTP_S 12
+#define VLAN_FID_M 0x7F
+
+#define REG_SW_VLAN_ENTRY_UNTAG__4 0x0404
+#define REG_SW_VLAN_ENTRY_PORTS__4 0x0408
+#define REG_SW_VLAN_ENTRY_INDEX__2 0x040C
+
+#define VLAN_INDEX_M 0x0FFF
+
+#define REG_SW_VLAN_CTRL 0x040E
+#define VLAN_START BIT(7)
+#define VLAN_ACTION 0x3
+#define VLAN_WRITE 1
+#define VLAN_READ 2
+#define VLAN_CLEAR 3
+
+#define REG_SW_ALU_INDEX_0 0x0410
+#define ALU_FID_INDEX_S 16
+#define ALU_FID_SIZE 127
+#define ALU_MAC_ADDR_HI 0xFFFF
+
+#define REG_SW_ALU_INDEX_1 0x0414
+#define ALU_DIRECT_INDEX_M (BIT(12) - 1)
+
+#define REG_SW_ALU_CTRL__4 0x0418
+#define REG_SW_ALU_CTRL(num) (REG_SW_ALU_CTRL__4 + ((num) * 4))
+
+#define ALU_STA_DYN_CNT 2
+#define ALU_VALID_CNT_M (BIT(14) - 1)
+#define ALU_VALID_CNT_S 16
+#define ALU_START BIT(7)
+#define ALU_VALID BIT(6)
+#define ALU_VALID_OR_STOP BIT(5)
+#define ALU_DIRECT BIT(2)
+#define ALU_ACTION 0x3
+#define ALU_WRITE 1
+#define ALU_READ 2
+#define ALU_SEARCH 3
+
+#define REG_SW_ALU_STAT_CTRL__4 0x041C
+#define ALU_STAT_VALID_CNT_M (BIT(9) - 1)
+#define ALU_STAT_VALID_CNT_S 20
+#define ALU_STAT_INDEX_M (BIT(8) - 1)
+#define ALU_STAT_INDEX_S 8
+#define ALU_RESV_MCAST_INDEX_M (BIT(6) - 1)
+#define ALU_STAT_START BIT(7)
+#define ALU_STAT_VALID BIT(6)
+#define ALU_STAT_VALID_OR_STOP BIT(5)
+#define ALU_STAT_USE_FID BIT(4)
+#define ALU_STAT_DIRECT BIT(3)
+#define ALU_RESV_MCAST_ADDR BIT(2)
+#define ALU_STAT_ACTION 0x3
+#define ALU_STAT_WRITE 1
+#define ALU_STAT_READ 2
+#define ALU_STAT_SEARCH 3
+
+#define REG_SW_ALU_VAL_A 0x0420
+#define ALU_V_STATIC_VALID BIT(31)
+#define ALU_V_SRC_FILTER BIT(30)
+#define ALU_V_DST_FILTER BIT(29)
+#define ALU_V_PRIO_AGE_CNT_M (BIT(3) - 1)
+#define ALU_V_PRIO_AGE_CNT_S 26
+#define ALU_V_MSTP_M 0x7
+
+#define REG_SW_ALU_VAL_B 0x0424
+#define ALU_V_OVERRIDE BIT(31)
+#define ALU_V_USE_FID BIT(30)
+#define ALU_V_PORT_MAP 0xFF
+
+#define REG_SW_ALU_VAL_C 0x0428
+#define ALU_V_FID_M (BIT(16) - 1)
+#define ALU_V_FID_S 16
+#define ALU_V_MAC_ADDR_HI 0xFFFF
+
+#define REG_SW_ALU_VAL_D 0x042C
+
+#define PORT_CTRL_ADDR(port, addr) ((addr) | (((port) + 1) << 12))
+
+#define REG_GLOBAL_RR_INDEX__1 0x0600
+
+/* VPHY */
+#define REG_VPHY_CTRL__2 0x0700
+#define REG_VPHY_STAT__2 0x0704
+#define REG_VPHY_ID_HI__2 0x0708
+#define REG_VPHY_ID_LO__2 0x070C
+#define REG_VPHY_AUTO_NEG__2 0x0710
+#define REG_VPHY_REMOTE_CAP__2 0x0714
+
+#define REG_VPHY_EXPANSION__2 0x0718
+
+#define REG_VPHY_M_CTRL__2 0x0724
+#define REG_VPHY_M_STAT__2 0x0728
+
+#define REG_VPHY_EXT_STAT__2 0x073C
+#define VPHY_EXT_1000_X_FULL BIT(15)
+#define VPHY_EXT_1000_X_HALF BIT(14)
+#define VPHY_EXT_1000_T_FULL BIT(13)
+#define VPHY_EXT_1000_T_HALF BIT(12)
+
+#define REG_VPHY_DEVAD_0__2 0x0740
+#define REG_VPHY_DEVAD_1__2 0x0744
+#define REG_VPHY_DEVAD_2__2 0x0748
+#define REG_VPHY_DEVAD_3__2 0x074C
+
+#define VPHY_DEVAD_UPDATE BIT(7)
+#define VPHY_DEVAD_M 0x1F
+#define VPHY_DEVAD_S 8
+
+#define REG_VPHY_SMI_ADDR__2 0x0750
+#define REG_VPHY_SMI_DATA_LO__2 0x0754
+#define REG_VPHY_SMI_DATA_HI__2 0x0758
+
+#define REG_VPHY_IND_ADDR__2 0x075C
+#define REG_VPHY_IND_DATA__2 0x0760
+#define REG_VPHY_IND_CTRL__2 0x0768
+
+#define VPHY_IND_WRITE BIT(1)
+#define VPHY_IND_BUSY BIT(0)
+
+#define REG_VPHY_SPECIAL_CTRL__2 0x077C
+#define VPHY_SMI_INDIRECT_ENABLE BIT(15)
+#define VPHY_SW_LOOPBACK BIT(14)
+#define VPHY_MDIO_INTERNAL_ENABLE BIT(13)
+#define VPHY_SPI_INDIRECT_ENABLE BIT(12)
+#define VPHY_PORT_MODE_M 0x3
+#define VPHY_PORT_MODE_S 8
+#define VPHY_MODE_RGMII 0
+#define VPHY_MODE_MII_PHY 1
+#define VPHY_MODE_SGMII 2
+#define VPHY_MODE_RMII_PHY 3
+#define VPHY_SW_COLLISION_TEST BIT(7)
+#define VPHY_SPEED_DUPLEX_STAT_M 0x7
+#define VPHY_SPEED_DUPLEX_STAT_S 2
+#define VPHY_SPEED_1000 BIT(4)
+#define VPHY_SPEED_100 BIT(3)
+#define VPHY_FULL_DUPLEX BIT(2)
+
+/* 0 - Operation */
+#define REG_PORT_DEFAULT_VID 0x0000
+
+#define REG_PORT_CUSTOM_VID 0x0002
+#define REG_PORT_PME_STATUS 0x0013
+
+#define REG_PORT_PME_CTRL 0x0017
+#define PME_WOL_MAGICPKT BIT(2)
+#define PME_WOL_LINKUP BIT(1)
+#define PME_WOL_ENERGY BIT(0)
+
+#define REG_PORT_INT_STATUS 0x001B
+#define REG_PORT_INT_MASK 0x001F
+
+#define PORT_TAS_INT BIT(5)
+#define PORT_SGMII_INT BIT(3)
+#define PORT_PTP_INT BIT(2)
+#define PORT_PHY_INT BIT(1)
+#define PORT_ACL_INT BIT(0)
+
+#define PORT_INT_MASK \
+ ( \
+ PORT_TAS_INT | \
+ PORT_SGMII_INT | PORT_PTP_INT | PORT_PHY_INT | PORT_ACL_INT)
+
+#define REG_PORT_CTRL_0 0x0020
+
+#define PORT_MAC_LOOPBACK BIT(7)
+#define PORT_MAC_REMOTE_LOOPBACK BIT(6)
+#define PORT_K2L_INSERT_ENABLE BIT(5)
+#define PORT_K2L_DEBUG_ENABLE BIT(4)
+#define PORT_TAIL_TAG_ENABLE BIT(2)
+#define PORT_QUEUE_SPLIT_ENABLE 0x3
+
+#define REG_PORT_CTRL_1 0x0021
+#define PORT_SRP_ENABLE 0x3
+
+#define REG_PORT_STATUS_0 0x0030
+#define PORT_INTF_SPEED_M 0x3
+#define PORT_INTF_SPEED_S 3
+#define PORT_INTF_FULL_DUPLEX BIT(2)
+
+#define REG_PORT_STATUS_1 0x0034
+
+/* 1 - PHY */
+#define REG_VPHY_SMI_ADDR 0x14
+#define REG_VPHY_SMI_DATA_LO 0x15
+#define REG_VPHY_SMI_DATA_HI 0x16
+
+#define REG_VPHY_SPECIAL_CTRL_STAT 0x1F
+
+#define REG_PORT_T1_PHY_CTRL_BASE 0x0100
+#define REG_PORT_TX_PHY_CTRL_BASE 0x0280
+#define REG_TX_PHY_CTRL_BASE 0x0980
+
+#define REG_PORT_PHY_1000_CTRL 0x0112
+#define PORT_AUTO_NEG_MANUAL BIT(12)
+#define PORT_AUTO_NEG_M BIT(11)
+#define PORT_AUTO_NEG_M_PREFERRED BIT(10)
+#define PORT_AUTO_NEG_1000BT_FD BIT(9)
+#define PORT_AUTO_NEG_1000BT BIT(8)
+
+#define REG_PORT_PHY_1000_STATUS 0x0114
+
+#define REG_PORT_PHY_RXER_COUNTER 0x012A
+#define REG_PORT_PHY_INT_ENABLE 0x0136
+#define REG_PORT_PHY_INT_STATUS 0x0137
+
+/* Same as PORT_PHY_LOOPBACK */
+#define PORT_PHY_PCS_LOOPBACK BIT(0)
+
+#define REG_PORT_PHY_DIGITAL_DEBUG_2 0x013A
+
+#define REG_PORT_PHY_DIGITAL_DEBUG_3 0x013C
+#define PORT_100BT_FIXED_LATENCY BIT(15)
+
+#define REG_PORT_PHY_PHY_CTRL 0x013E
+#define PORT_INT_PIN_HIGH BIT(14)
+#define PORT_ENABLE_JABBER BIT(9)
+#define PORT_STAT_SPEED_1000MBIT BIT(6)
+#define PORT_STAT_SPEED_100MBIT BIT(5)
+#define PORT_STAT_SPEED_10MBIT BIT(4)
+#define PORT_STAT_FULL_DUPLEX BIT(3)
+
+/* Same as PORT_PHY_STAT_M */
+#define PORT_STAT_M BIT(2)
+#define PORT_RESET BIT(1)
+#define PORT_LINK_STATUS_FAIL BIT(0)
+
+/* 3 - xMII */
+#define REG_PORT_XMII_CTRL_0 0x0300
+#define PORT_SGMII_SEL BIT(7)
+#define PORT_MII_FULL_DUPLEX BIT(6)
+#define PORT_MII_TX_FLOW_CTRL BIT(5)
+#define PORT_MII_100MBIT BIT(4)
+#define PORT_MII_RX_FLOW_CTRL BIT(3)
+#define PORT_GRXC_ENABLE BIT(0)
+
+#define REG_PORT_XMII_CTRL_1 0x0301
+#define PORT_MII_NOT_1GBIT BIT(6)
+#define PORT_MII_SEL_EDGE BIT(5)
+#define PORT_RGMII_ID_IG_ENABLE BIT(4)
+#define PORT_RGMII_ID_EG_ENABLE BIT(3)
+#define PORT_MII_MAC_MODE BIT(2)
+#define PORT_MII_SEL_M 0x3
+#define PORT_RGMII_SEL 0x0
+#define PORT_RMII_SEL 0x1
+#define PORT_MII_SEL 0x2
+
+#define REG_PORT_XMII_CTRL_2 0x0302
+#define PORT_RGMII_RX_STS_ENABLE BIT(0)
+
+#define REG_PORT_XMII_CTRL_3 0x0303
+#define PORT_DUPLEX_STATUS_FULL BIT(3)
+
+#define REG_PORT_XMII_CTRL_4 0x0304
+#define PORT_TX_TUNE_ADJ 0x3F80
+
+#define REG_PORT_XMII_CTRL_5 0x0306
+#define PORT_DLL_RESET BIT(15)
+#define PORT_RX_TUNE_ADJ 0x3F80
+
+#define PORT_TUNE_ADJ 0x3F80
+
+/* 4 - MAC */
+#define REG_PORT_MAC_CTRL_0 0x0400
+#define PORT_CHECK_LENGTH BIT(2)
+#define PORT_BROADCAST_STORM BIT(1)
+#define PORT_JUMBO_PACKET BIT(0)
+
+#define REG_PORT_MAC_CTRL_1 0x0401
+#define PORT_BACK_PRESSURE BIT(3)
+#define PORT_PASS_ALL BIT(0)
+
+#define REG_PORT_MAC_CTRL_2 0x0402
+#define PORT_100BT_EEE_DISABLE BIT(7)
+#define PORT_1000BT_EEE_DISABLE BIT(6)
+
+#define REG_PORT_MAC_IN_RATE_LIMIT 0x0403
+
+#define REG_PORT_MTU__2 0x0404
+#define PORT_RATE_LIMIT_M (BIT(7) - 1)
+
+/* 5 - MIB Counters */
+#define REG_PORT_MIB_CTRL_STAT 0x0500
+#define MIB_COUNTER_OVERFLOW BIT(31)
+#define MIB_COUNTER_VALID BIT(30)
+#define MIB_COUNTER_READ BIT(25)
+#define MIB_COUNTER_FLUSH_FREEZE BIT(24)
+#define MIB_COUNTER_INDEX_M (BIT(8) - 1)
+#define MIB_COUNTER_INDEX_S 16
+#define MIB_COUNTER_DATA_HI_M 0xF
+
+#define REG_PORT_MIB_DATA 0x0504
+
+/* 8 - Classification and Policing */
+#define REG_PORT_MRI_MIRROR_CTRL 0x0800
+#define PORT_MIRROR_RX BIT(6)
+#define PORT_MIRROR_TX BIT(5)
+#define PORT_MIRROR_SNIFFER BIT(1)
+
+#define REG_PORT_MRI_PRIO_CTRL 0x0801
+#define PORT_HIGHEST_PRIO BIT(7)
+#define PORT_OR_PRIO BIT(6)
+#define PORT_MAC_PRIO_ENABLE BIT(4)
+#define PORT_VLAN_PRIO_ENABLE BIT(3)
+#define PORT_802_1P_PRIO_ENABLE BIT(2)
+#define PORT_DIFFSERV_PRIO_ENABLE BIT(1)
+#define PORT_ACL_PRIO_ENABLE BIT(0)
+
+#define REG_PORT_MRI_MAC_CTRL 0x0802
+#define PORT_USER_PRIO_CEILING BIT(7)
+#define PORT_DROP_NON_VLAN BIT(4)
+#define PORT_DROP_TAG BIT(3)
+#define PORT_BASED_PRIO_M KS_PRIO_M
+#define PORT_BASED_PRIO_S 0
+
+#define REG_PORT_MRI_TC_MAP__4 0x0808
+
+/* 9 - Shaping */
+#define REG_PORT_MTI_QUEUE_INDEX__4 0x0900
+
+#define REG_PORT_MTI_QUEUE_CTRL_0__4 0x0904
+#define MTI_PVID_REPLACE BIT(0)
+
+#define REG_PORT_MTI_QUEUE_CTRL_0 0x0914
+
+/* A - QM */
+#define REG_PORT_QM_CTRL__4 0x0A00
+#define PORT_QM_DROP_PRIO_M 0x3
+
+#define REG_PORT_VLAN_MEMBERSHIP__4 0x0A04
+
+#define REG_PORT_QM_QUEUE_INDEX__4 0x0A08
+#define PORT_QM_QUEUE_INDEX_S 24
+#define PORT_QM_BURST_SIZE_S 16
+#define PORT_QM_MIN_RESV_SPACE_M (BIT(11) - 1)
+
+#define REG_PORT_QM_WATER_MARK__4 0x0A0C
+#define PORT_QM_HI_WATER_MARK_S 16
+#define PORT_QM_LO_WATER_MARK_S 0
+#define PORT_QM_WATER_MARK_M (BIT(11) - 1)
+
+#define REG_PORT_QM_TX_CNT_0__4 0x0A10
+#define PORT_QM_TX_CNT_USED_S 0
+#define PORT_QM_TX_CNT_M (BIT(11) - 1)
+
+#define REG_PORT_QM_TX_CNT_1__4 0x0A14
+#define PORT_QM_TX_CNT_CALCULATED_S 16
+#define PORT_QM_TX_CNT_AVAIL_S 0
+
+/* B - LUE */
+#define REG_PORT_LUE_CTRL 0x0B00
+
+#define PORT_VLAN_LOOKUP_VID_0 BIT(7)
+#define PORT_INGRESS_FILTER BIT(6)
+#define PORT_DISCARD_NON_VID BIT(5)
+#define PORT_MAC_BASED_802_1X BIT(4)
+#define PORT_SRC_ADDR_FILTER BIT(3)
+
+#define REG_PORT_LUE_MSTP_INDEX 0x0B01
+
+#define REG_PORT_LUE_MSTP_STATE 0x0B04
+
+#define PORT_TX_ENABLE BIT(2)
+#define PORT_RX_ENABLE BIT(1)
+#define PORT_LEARN_DISABLE BIT(0)
+
+#define REG_PORT_LUE_LEARN_CNT__2 0x0B08
+
+#define REG_PORT_LUE_UNK_CTL0 0x0B0E
+#define REG_PORT_LUE_UNK_CTL1 0x0B10
+#define REG_PORT_LUE_UNK_VID_CTRL__2 0x0B12
+
+#define PORT_UNK_UCAST_MCAST_ENABLE BIT(15)
+#define PORT_UCAST_MCAST_MASK 0xFF
+#define PORT_UNK_VID_ENABLE BIT(15)
+
+#define PRIO_QUEUES 8
+#define RX_PRIO_QUEUES 8
+#define KS_PRIO_IN_REG 2
+#define TOTAL_PORT_NUM 8
+
+#define LAN937X_COUNTER_NUM 0x20
+#define TOTAL_LAN937X_COUNTER_NUM (LAN937X_COUNTER_NUM + 2 + 2)
+
+#define SWITCH_COUNTER_NUM LAN937X_COUNTER_NUM
+
+#define P_BCAST_STORM_CTRL REG_PORT_MAC_CTRL_0
+#define P_PRIO_CTRL REG_PORT_MRI_PRIO_CTRL
+#define P_MIRROR_CTRL REG_PORT_MRI_MIRROR_CTRL
+#define P_STP_CTRL REG_PORT_LUE_MSTP_STATE
+#define P_PHY_CTRL REG_PORT_PHY_CTRL
+#define P_NEG_RESTART_CTRL REG_PORT_PHY_CTRL
+#define P_LINK_STATUS REG_PORT_PHY_STATUS
+#define P_SPEED_STATUS REG_PORT_PHY_PHY_CTRL
+#define P_RATE_LIMIT_CTRL REG_PORT_MAC_IN_RATE_LIMIT
+
+#define S_LINK_AGING_CTRL REG_SW_LUE_CTRL_1
+#define S_MIRROR_CTRL REG_SW_MRI_CTRL_0
+#define S_REPLACE_VID_CTRL REG_SW_MAC_CTRL_2
+#define S_802_1P_PRIO_CTRL REG_SW_MAC_802_1P_MAP_0
+#define S_TOS_PRIO_CTRL REG_SW_MAC_TOS_PRIO_0
+#define S_FLUSH_TABLE_CTRL REG_SW_LUE_CTRL_1
+
+#define REG_SWITCH_RESET REG_RESET_CTRL
+
+#define SW_FLUSH_DYN_MAC_TABLE SW_FLUSH_MSTP_TABLE
+
+#define MAX_TIMESTAMP_UNIT 2
+#define MAX_TRIG_UNIT 3
+#define MAX_TIMESTAMP_EVENT_UNIT 8
+#define MAX_GPIO 2
+#define MAX_CLOCK 2
+
+#define PTP_TRIG_UNIT_M (BIT(MAX_TRIG_UNIT) - 1)
+#define PTP_TS_UNIT_M (BIT(MAX_TIMESTAMP_UNIT) - 1)
+
+#define TAIL_TAG_PTP BIT(7)
+#define TAIL_TAG_NEXT_CHIP BIT(6)
+#define TAIL_TAG_K2L BIT(5)
+#define TAIL_TAG_PTP_1_STEP BIT(4)
+#define TAIL_TAG_PTP_P2P BIT(3)
+#define TAIL_TAG_RX_PORTS_M 0x7
+
+/* 148,800 frames * 67 ms / 100 */
+#define BR_STORM_VALUE 9969
+
+#define SW_CHECK_LENGTH BIT(3)
+
+#define FR_MIN_SIZE 1522
+#define FR_MAX_SIZE 9000
+
+#define PORT_JUMBO_EN BIT(0)
+#define PORT_FR_CHK_LENGTH BIT(2)
+#define PORT_MAX_FR_SIZE 0x404
+
+#define FR_SIZE_CPU_PORT 1540
+
+#define REG_PORT_CTRL_0 0x0020
+#define PORT_FULL_DUPLEX BIT(6)
+#define PORT_TX_FLOW_CTRL BIT(5)
+#define PORT_RX_FLOW_CTRL BIT(3)
+#define PORT_MAC_SPEED_100 BIT(4)
+
+#define PORT_QUEUE_SPLIT_ENABLE 0x3
+
+/* Get fid from vid, fid 0 is not used if vid is greater than 127 */
+#define LAN937X_GET_FID(vid) (((vid) % ALU_FID_SIZE) + 1)
+
+/* Driver set switch broadcast storm protection at 10% rate */
+#define BR_STORM_PROT_RATE 10
+
+#define MII_BMSR_100BASE_TX_FD BIT(14)
+
+#define PHY_LINK_UP 1
+#define PHY_LINK_DOWN 0
+
+/* The port number as per the datasheet */
+#define RGMII_2_PORT_NUM 5
+#define RGMII_1_PORT_NUM 6
+#define SGMII_PORT_NUM 4
+#define TXPHY_PORT_NUM 4
+
+#define GET_CHIP_ID_LSB(chip_id) (((chip_id) >> 8) & 0xff)
+#define LAN937X_RGMII_2_PORT (RGMII_2_PORT_NUM - 1)
+#define LAN937X_RGMII_1_PORT (RGMII_1_PORT_NUM - 1)
+#define LAN937X_SGMII_PORT (SGMII_PORT_NUM - 1)
+#define LAN937X_TXPHY_PORT (TXPHY_PORT_NUM - 1)
+#define LAN937X_TAG_LEN 2
+
+#define RGMII_1_TX_DELAY_2NS 2
+#define RGMII_2_TX_DELAY_2NS 0
+#define RGMII_1_RX_DELAY_2NS 0x1B
+#define RGMII_2_RX_DELAY_2NS 0x14
+
+#endif
diff --git a/drivers/net/dsa/microchip/lan937x_spi.c b/drivers/net/dsa/microchip/lan937x_spi.c
new file mode 100644
index 000000000000..a50dfcf27aff
--- /dev/null
+++ b/drivers/net/dsa/microchip/lan937x_spi.c
@@ -0,0 +1,236 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Microchip LAN937X switch driver register access through SPI
+ * Copyright (C) 2019-2021 Microchip Technology Inc.
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/spi/spi.h>
+#include <linux/of_device.h>
+
+#include "ksz_common.h"
+
+#define SPI_ADDR_SHIFT 24
+#define SPI_ADDR_ALIGN 3
+#define SPI_TURNAROUND_SHIFT 5
+
+KSZ_REGMAP_TABLE(lan937x, 32, SPI_ADDR_SHIFT, SPI_TURNAROUND_SHIFT,
+ SPI_ADDR_ALIGN);
+
+struct lan937x_chip_data {
+ u32 chip_id;
+ const char *dev_name;
+ int num_vlans;
+ int num_alus;
+ int num_statics;
+ int cpu_ports;
+ int port_cnt;
+};
+
+static const struct of_device_id lan937x_dt_ids[];
+
+static const struct lan937x_chip_data lan937x_switch_chips[] = {
+ {
+ .chip_id = 0x00937010,
+ .dev_name = "LAN9370",
+ .num_vlans = 4096,
+ .num_alus = 1024,
+ .num_statics = 256,
+ /* can be configured as cpu port */
+ .cpu_ports = 0x10,
+ /* total port count */
+ .port_cnt = 5,
+ },
+ {
+ .chip_id = 0x00937110,
+ .dev_name = "LAN9371",
+ .num_vlans = 4096,
+ .num_alus = 1024,
+ .num_statics = 256,
+ /* can be configured as cpu port */
+ .cpu_ports = 0x30,
+ /* total port count */
+ .port_cnt = 6,
+ },
+ {
+ .chip_id = 0x00937210,
+ .dev_name = "LAN9372",
+ .num_vlans = 4096,
+ .num_alus = 1024,
+ .num_statics = 256,
+ /* can be configured as cpu port */
+ .cpu_ports = 0x30,
+ /* total port count */
+ .port_cnt = 8,
+ },
+ {
+ .chip_id = 0x00937310,
+ .dev_name = "LAN9373",
+ .num_vlans = 4096,
+ .num_alus = 1024,
+ .num_statics = 256,
+ /* can be configured as cpu port */
+ .cpu_ports = 0x38,
+ /* total port count */
+ .port_cnt = 5,
+ },
+ {
+ .chip_id = 0x00937410,
+ .dev_name = "LAN9374",
+ .num_vlans = 4096,
+ .num_alus = 1024,
+ .num_statics = 256,
+ /* can be configured as cpu port */
+ .cpu_ports = 0x30,
+ /* total port count */
+ .port_cnt = 8,
+ },
+};
+
+static int lan937x_spi_probe(struct spi_device *spi)
+{
+ struct regmap_config rc;
+ struct ksz_device *dev;
+ int i, ret;
+
+ dev = ksz_switch_alloc(&spi->dev, spi);
+ if (!dev)
+ return -ENOMEM;
+
+ for (i = 0; i < ARRAY_SIZE(lan937x_regmap_config); i++) {
+ rc = lan937x_regmap_config[i];
+ rc.lock_arg = &dev->regmap_mutex;
+ dev->regmap[i] = devm_regmap_init_spi(spi, &rc);
+
+ if (IS_ERR(dev->regmap[i])) {
+ ret = PTR_ERR(dev->regmap[i]);
+ dev_err(&spi->dev,
+ "Failed to initialize regmap%i: %d\n",
+ lan937x_regmap_config[i].val_bits, ret);
+ return ret;
+ }
+ }
+
+ if (spi->dev.platform_data)
+ dev->pdata = spi->dev.platform_data;
+
+ ret = lan937x_switch_register(dev);
+ /* Main DSA driver may not be started yet. */
+ if (ret)
+ return ret;
+
+ spi_set_drvdata(spi, dev);
+
+ return 0;
+}
+
+int lan937x_check_device_id(struct ksz_device *dev)
+{
+ const struct lan937x_chip_data *dt_chip_data;
+ const struct of_device_id *match;
+ int i;
+
+ dt_chip_data = of_device_get_match_data(dev->dev);
+
+ if (!dt_chip_data)
+ return -EINVAL;
+
+ for (match = lan937x_dt_ids; match->compatible[0]; match++) {
+ const struct lan937x_chip_data *chip_data = match->data;
+
+ /* Check for chip id */
+ if (chip_data->chip_id != dev->chip_id)
+ continue;
+
+ /* Check for Device Tree and Chip ID */
+ if (dt_chip_data->chip_id != dev->chip_id) {
+ dev_err(dev->dev,
+ "Device tree specifies chip %s but found %s, please fix it!\n",
+ dt_chip_data->dev_name, chip_data->dev_name);
+ return -ENODEV;
+ }
+
+ break;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(lan937x_switch_chips); i++) {
+ const struct lan937x_chip_data *chip = &lan937x_switch_chips[i];
+
+ if (dev->chip_id == chip->chip_id) {
+ dev->name = chip->dev_name;
+ dev->num_vlans = chip->num_vlans;
+ dev->num_alus = chip->num_alus;
+ dev->num_statics = chip->num_statics;
+ dev->port_cnt = chip->port_cnt;
+ dev->cpu_ports = chip->cpu_ports;
+ break;
+ }
+ }
+
+ /* no switch found */
+ if (!dev->port_cnt)
+ return -ENODEV;
+
+ return 0;
+}
+EXPORT_SYMBOL(lan937x_check_device_id);
+
+static void lan937x_spi_remove(struct spi_device *spi)
+{
+ struct ksz_device *dev = spi_get_drvdata(spi);
+
+ if (dev)
+ ksz_switch_remove(dev);
+
+ spi_set_drvdata(spi, NULL);
+}
+
+static void lan937x_spi_shutdown(struct spi_device *spi)
+{
+ struct ksz_device *dev = spi_get_drvdata(spi);
+
+ if (dev)
+ dsa_switch_shutdown(dev->ds);
+
+ spi_set_drvdata(spi, NULL);
+}
+
+static const struct of_device_id lan937x_dt_ids[] = {
+ { .compatible = "microchip,lan9370", .data = &lan937x_switch_chips[0] },
+ { .compatible = "microchip,lan9371", .data = &lan937x_switch_chips[1] },
+ { .compatible = "microchip,lan9372", .data = &lan937x_switch_chips[2] },
+ { .compatible = "microchip,lan9373", .data = &lan937x_switch_chips[3] },
+ { .compatible = "microchip,lan9374", .data = &lan937x_switch_chips[4] },
+ {},
+};
+MODULE_DEVICE_TABLE(of, lan937x_dt_ids);
+
+static const struct spi_device_id lan937x_spi_ids[] = {
+ { .name = "lan9370" },
+ { .name = "lan9371" },
+ { .name = "lan9372" },
+ { .name = "lan9373" },
+ { .name = "lan9374" },
+ {},
+};
+MODULE_DEVICE_TABLE(spi, lan937x_spi_ids);
+
+static struct spi_driver lan937x_spi_driver = {
+ .driver = {
+ .name = "lan937x-switch",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(lan937x_dt_ids),
+ },
+ .probe = lan937x_spi_probe,
+ .remove = lan937x_spi_remove,
+ .shutdown = lan937x_spi_shutdown,
+ .id_table = lan937x_spi_ids,
+};
+
+module_spi_driver(lan937x_spi_driver);
+
+MODULE_ALIAS("spi:lan937x");
+
+MODULE_AUTHOR("Prasanna Vengateshan Varadharajan <Prasanna.Vengateshan@...rochip.com>");
+MODULE_DESCRIPTION("Microchip LAN937x Series Switch SPI access Driver");
+MODULE_LICENSE("GPL");
--
2.30.2
Powered by blists - more mailing lists