| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20220406091722.314590-1-fabio.aiuto@amarulasolutions.com>
Date: Wed, 6 Apr 2022 11:17:22 +0200
From: Fabio Aiuto <fabio.aiuto@...rulasolutions.com>
To: agk@...hat.com, snitzer@...nel.org
Cc: dm-devel@...hat.com, linux-kernel@...r.kernel.org,
Michael Trimarchi <michael@...rulasolutions.com>
Subject: [PATCH v2] md: dm-init: Wait devices if it's not find on first adpet
From: Michael Trimarchi <michael@...rulasolutions.com>
The device driver can be deferrable and can be a race during
the dm-init early. We need to wait all the probe are really finished
in a loop as is done in do_mounts. This is was tested on kernel 5.4
but code seems was not changed since that time
003: imx8mq-usb-phy 381f0040.usb-phy: 381f0040.usb-phy supply vbus not found, using dummy regulator
003: imx8mq-usb-phy 382f0040.usb-phy: 382f0040.usb-phy supply vbus not found, using dummy regulator
003: imx-cpufreq-dt imx-cpufreq-dt: cpu speed grade 5 mkt segment 0 supported-hw 0x20 0x1
003: caam-dma caam-dma: caam dma support with 2 job rings
000: hctosys: unable to open rtc device (rtc0)
000: device-mapper: init: waiting for all devices to be available before creating mapped devices
002: device-mapper: table: 254:0: verity: Data device lookup failed
002: device-mapper: ioctl: error adding target to table
002: crng init done
003: of_cfs_init
003: of_cfs_init: OK
003: Waiting for root device /dev/dm-0...
001: mmc2: new HS400 Enhanced strobe MMC card at address 0001
001: mmcblk2: mmc2:0001 IB2916 14.6 GiB
001: mmcblk2boot0: mmc2:0001 IB2916 partition 1 4.00 MiB
001: mmcblk2boot1: mmc2:0001 IB2916 partition 2 4.00 MiB
001: mmcblk2rpmb: mmc2:0001 IB2916 partition 3 4.00 MiB, chardev (249:0)
001: mmcblk2: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11
001: VSD_3V3: disabling
with the patch
003: device-mapper: init: waiting for all devices to be available before creating mapped devices
000: device-mapper: table: 254:0: verity: Data device lookup failed
000: device-mapper: ioctl: error adding target to table
002: crng init done
003: device-mapper: init: waiting for all devices to be available before creating mapped devices
003: device-mapper: table: 254:0: verity: Data device lookup failed
003: device-mapper: ioctl: error adding target to table
003: device-mapper: init: waiting for all devices to be available before creating mapped devices
000: device-mapper: table: 254:0: verity: Data device lookup failed
000: device-mapper: ioctl: error adding target to table
002: device-mapper: init: waiting for all devices to be available before creating mapped devices
002: device-mapper: table: 254:0: verity: Data device lookup failed
002: device-mapper: ioctl: error adding target to table
000: device-mapper: init: waiting for all devices to be available before creating mapped devices
000: device-mapper: table: 254:0: verity: Data device lookup failed
000: device-mapper: ioctl: error adding target to table
003: mmc2: new HS400 Enhanced strobe MMC card at address 0001
003: mmcblk2: mmc2:0001 DG4016 14.7 GiB
003: mmcblk2boot0: mmc2:0001 DG4016 partition 1 4.00 MiB
003: mmcblk2boot1: mmc2:0001 DG4016 partition 2 4.00 MiB
003: mmcblk2rpmb: mmc2:0001 DG4016 partition 3 4.00 MiB, chardev (249:0)
003: mmcblk2: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11
002: device-mapper: init: waiting for all devices to be available before creating mapped devices
003: device-mapper: verity: sha256 using implementation "sha256-caam"
000: device-mapper: ioctl: dm-0 (rootfs) is ready
Wait loop is limited to 10 at the moment for our use case showed no
more than 4 loops before succesfully find data device.
Signed-off-by: Michael Trimarchi <michael@...rulasolutions.com>
Signed-off-by: Fabio Aiuto <fabio.aiuto@...rulasolutions.com>
---
Changes from v1:
- limit the loop to 10 iterations
- change variable names
- check only for -ENODEV failures
drivers/md/dm-init.c | 20 ++++++++++++++++++--
1 file changed, 18 insertions(+), 2 deletions(-)
diff --git a/drivers/md/dm-init.c b/drivers/md/dm-init.c
index b0c45c6ebe0b..406a9f92723d 100644
--- a/drivers/md/dm-init.c
+++ b/drivers/md/dm-init.c
@@ -7,7 +7,9 @@
* This file is released under the GPLv2.
*/
+#include <linux/async.h>
#include <linux/ctype.h>
+#include <linux/delay.h>
#include <linux/device.h>
#include <linux/device-mapper.h>
#include <linux/init.h>
@@ -18,6 +20,7 @@
#define DM_MAX_DEVICES 256
#define DM_MAX_TARGETS 256
#define DM_MAX_STR_SIZE 4096
+#define DM_MAX_PROBE_WAIT_RETRY 10
static char *create;
@@ -267,6 +270,8 @@ static int __init dm_init_init(void)
LIST_HEAD(devices);
char *str;
int r;
+ int loopcnt = DM_MAX_PROBE_WAIT_RETRY;
+ bool devnotfound = false;
if (!create)
return 0;
@@ -275,6 +280,7 @@ static int __init dm_init_init(void)
DMERR("Argument is too big. Limit is %d", DM_MAX_STR_SIZE);
return -EINVAL;
}
+retry:
str = kstrndup(create, DM_MAX_STR_SIZE, GFP_KERNEL);
if (!str)
return -ENOMEM;
@@ -287,13 +293,23 @@ static int __init dm_init_init(void)
wait_for_device_probe();
list_for_each_entry(dev, &devices, list) {
- if (dm_early_create(&dev->dmi, dev->table,
- dev->target_args_array))
+ r = dm_early_create(&dev->dmi, dev->table, dev->target_args_array);
+ if (r == -ENODEV) {
+ devnotfound = true;
break;
+ }
}
+
out:
kfree(str);
dm_setup_cleanup(&devices);
+ if (devnotfound && loopcnt) {
+ msleep(5);
+ devnotfound = false;
+ loopcnt--;
+ goto retry;
+ }
+
return r;
}
--
2.30.2
Powered by blists - more mailing lists