| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20220414233055.586962-4-chris.packham@alliedtelesis.co.nz>
Date: Fri, 15 Apr 2022 11:30:54 +1200
From: Chris Packham <chris.packham@...iedtelesis.co.nz>
To: linus.walleij@...aro.org, robh+dt@...nel.org,
catalin.marinas@....com, will@...nel.org, andrew@...n.ch,
gregory.clement@...tlin.com, sebastian.hesselbarth@...il.com,
kostap@...vell.com, robert.marko@...tura.hr
Cc: linux-gpio@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
Chris Packham <chris.packham@...iedtelesis.co.nz>
Subject: [PATCH v4 3/4] arm64: dts: marvell: Add Armada 98DX2530 SoC and RD-AC5X board
The 98DX2530 SoC is the Control and Management CPU integrated into
the Marvell 98DX25xx and 98DX35xx series of switch chip (internally
referred to as AlleyCat5 and AlleyCat5X).
These files have been taken from the Marvell SDK and lightly cleaned
up with the License and copyright retained.
Signed-off-by: Chris Packham <chris.packham@...iedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@...n.ch>
---
Notes:
The Marvell SDK has a number of new compatible strings. I've brought
through some of the drivers or where possible used an in-tree
alternative (e.g. there is SDK code for a ac5-gpio but two instances of
the existing marvell,orion-gpio seems to cover what is needed if you use
an appropriate binding). I expect that there will a new series of
patches when I get some different hardware (or additions to this series
depending on if/when it lands).
Changes in v4:
- use 'phy-handle' instead of 'phy'
- move status="okay" on usb nodes to board dts
- Add review from Andrew
Changes in v3:
- Move memory node to board
- Use single digit reg value for phy address
- Remove MMC node (driver needs work)
- Remove syscon & simple-mfd for pinctrl
Changes in v2:
- Make pinctrl a child node of a syscon node
- Use marvell,armada-8k-gpio instead of orion-gpio
- Remove nand peripheral. The Marvell SDK does have some changes for the
ac5-nand-controller but I currently lack hardware with NAND fitted so
I can't test it right now. I've therefore chosen to omit the node and
not attempted to bring in the driver or binding.
- Remove pcie peripheral. Again there are changes in the SDK and I have
no way of testing them.
- Remove prestera node.
- Remove "marvell,ac5-ehci" compatible from USB node as
"marvell,orion-ehci" is sufficient
- Remove watchdog node. There is a buggy driver for the ac5 watchdog in
the SDK but it needs some work so I've dropped the node for now.
arch/arm64/boot/dts/marvell/Makefile | 1 +
.../boot/dts/marvell/armada-98dx2530.dtsi | 302 ++++++++++++++++++
arch/arm64/boot/dts/marvell/rd-ac5x.dts | 82 +++++
3 files changed, 385 insertions(+)
create mode 100644 arch/arm64/boot/dts/marvell/armada-98dx2530.dtsi
create mode 100644 arch/arm64/boot/dts/marvell/rd-ac5x.dts
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 1c794cdcb8e6..3905dee558b4 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -24,3 +24,4 @@ dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-A.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-B.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += rd-ac5x.dtb
diff --git a/arch/arm64/boot/dts/marvell/armada-98dx2530.dtsi b/arch/arm64/boot/dts/marvell/armada-98dx2530.dtsi
new file mode 100644
index 000000000000..3b9ea69f6f8d
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-98dx2530.dtsi
@@ -0,0 +1,302 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree For AC5.
+ *
+ * Copyright (C) 2021 Marvell
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ model = "Marvell AC5 SoC";
+ compatible = "marvell,ac5";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ aliases {
+ serial0 = &uart0;
+ spiflash0 = &spiflash0;
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ ethernet0 = ð0;
+ ethernet1 = ð1;
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_PPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <25000000>;
+ };
+
+ pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <GIC_PPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ dma-ranges;
+
+ internal-regs@...00000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ /* 16M internal register @ 0x7f00_0000 */
+ ranges = <0x0 0x0 0x7f000000 0x1000000>;
+ dma-coherent;
+
+ uart0: serial@...00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x12000 0x100>;
+ reg-shift = <2>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ reg-io-width = <1>;
+ clock-frequency = <328000000>;
+ status = "okay";
+ };
+
+ mdio: mdio@...04 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "marvell,orion-mdio";
+ reg = <0x22004 0x4>;
+ clocks = <&core_clock>;
+ };
+
+ i2c0: i2c@...00{
+ compatible = "marvell,mv78230-i2c";
+ reg = <0x11000 0x20>;
+
+ clocks = <&core_clock>;
+ clock-names = "core";
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency=<100000>;
+ status="okay";
+
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-1 = <&i2c0_gpio>;
+ scl_gpio = <&gpio0 26 GPIO_ACTIVE_HIGH>;
+ sda_gpio = <&gpio0 27 GPIO_ACTIVE_HIGH>;
+ };
+
+ i2c1: i2c@...00{
+ compatible = "marvell,mv78230-i2c";
+ reg = <0x11100 0x20>;
+
+ clocks = <&core_clock>;
+ clock-names = "core";
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency=<100000>;
+ status="okay";
+
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&i2c1_pins>;
+ pinctrl-1 = <&i2c1_gpio>;
+ scl_gpio = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+ sda_gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio0: gpio@...00 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18100 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pinctrl0 0 0 32>;
+ marvell,pwm-offset = <0x1f0>;
+ };
+
+ gpio1: gpio@...40 {
+ reg = <0x18140 0x40>;
+ compatible = "marvell,orion-gpio";
+ ngpios = <14>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pinctrl0 0 32 14>;
+ marvell,pwm-offset = <0x1f0>;
+ };
+ };
+
+ /*
+ * Dedicated section for devices behind 32bit controllers so we
+ * can configure specific DMA mapping for them
+ */
+ behind-32bit-controller@...00000 {
+ compatible = "simple-bus";
+ #address-cells = <0x2>;
+ #size-cells = <0x2>;
+ ranges = <0x0 0x0 0x0 0x7f000000 0x0 0x1000000>;
+ /* Host phy ram starts at 0x200M */
+ dma-ranges = <0x0 0x0 0x2 0x0 0x1 0x0>;
+ dma-coherent;
+
+ eth0: ethernet@...00 {
+ compatible = "marvell,armada-ac5-neta";
+ reg = <0x0 0x20000 0x0 0x4000>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&core_clock>;
+ status = "disabled";
+ phy-mode = "sgmii";
+ };
+
+ eth1: ethernet@...00 {
+ compatible = "marvell,armada-ac5-neta";
+ reg = <0x0 0x24000 0x0 0x4000>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&core_clock>;
+ status = "disabled";
+ phy-mode = "sgmii";
+ };
+
+ /* A dummy entry used for chipidea phy init */
+ usb1phy: usbphy {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+
+ /* USB0 is a host USB */
+ usb0: usb@...00 {
+ compatible = "marvell,orion-ehci";
+ reg = <0x0 0x80000 0x0 0x500>;
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ /* USB1 is a peripheral USB */
+ usb1: usb@...00 {
+ reg = <0x0 0xa0000 0x0 0x500>;
+ interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+ };
+
+ pinctrl0: pinctrl@...20100 {
+ compatible = "marvell,ac5-pinctrl";
+ reg = <0 0x80020100 0 0x20>;
+
+ i2c0_pins: i2c0-pins {
+ marvell,pins = "mpp26", "mpp27";
+ marvell,function = "i2c0";
+ };
+
+ i2c0_gpio: i2c0-gpio-pins {
+ marvell,pins = "mpp26", "mpp27";
+ marvell,function = "gpio";
+ };
+
+ i2c1_pins: i2c1-pins {
+ marvell,pins = "mpp20", "mpp21";
+ marvell,function = "i2c1";
+ };
+
+ i2c1_gpio: i2c1-gpio-pins {
+ marvell,pins = "mpp20", "mpp21";
+ marvell,function = "i2c1";
+ };
+ };
+
+ core_clock: core_clock@0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <400000000>;
+ };
+
+ axi_clock: axi_clock@0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <325000000>;
+ };
+
+ spi_clock: spi_clock@0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <200000000>;
+ };
+
+ spi0: spi@...a0000 {
+ compatible = "marvell,armada-3700-spi";
+ reg = <0x0 0x805a0000 0x0 0x50>;
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ clocks = <&spi_clock>;
+ interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+ num-cs = <1>;
+ status = "disabled";
+ };
+
+ spi1: spi@...a8000 {
+ compatible = "marvell,armada-3700-spi";
+ reg = <0x0 0x805a8000 0x0 0x50>;
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ clocks = <&spi_clock>;
+ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+ num-cs = <1>;
+ status = "disabled";
+ };
+ };
+
+ gic: interrupt-controller@...00000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ /*#redistributor-regions = <1>;*/
+ redistributor-stride = <0x0 0x20000>; // 128kB stride
+ reg = <0x0 0x80600000 0x0 0x10000>, /* GICD */
+ <0x0 0x80660000 0x0 0x40000>; /* GICR */
+ interrupts = <GIC_PPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&CPU0>;
+ };
+ core1 {
+ cpu = <&CPU1>;
+ };
+ };
+ };
+
+ CPU0:cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,armv8";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ next-level-cache = <&L2_0>;
+ };
+
+ CPU1:cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,armv8";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ next-level-cache = <&L2_0>;
+ };
+
+ L2_0: l2-cache0 {
+ compatible = "cache";
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/marvell/rd-ac5x.dts b/arch/arm64/boot/dts/marvell/rd-ac5x.dts
new file mode 100644
index 000000000000..71877bc967e2
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/rd-ac5x.dts
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree For AC5X.
+ *
+ * Copyright (C) 2021 Marvell
+ *
+ */
+/*
+ * Device Tree file for Marvell Alleycat 5X development board
+ * This board file supports the B configuration of the board
+ */
+
+/dts-v1/;
+
+#include "armada-98dx2530.dtsi"
+
+/ {
+ model = "Marvell RD-AC5X Board";
+ compatible = "marvell,ac5x", "marvell,ac5";
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x2 0x00000000 0x0 0x40000000>;
+ };
+};
+
+&mdio {
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ phy-handle = <&phy0>;
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+
+ spiflash0: spi-flash@0 {
+ compatible = "spi-nor";
+ spi-max-frequency = <50000000>;
+ spi-tx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
+ spi-rx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
+ reg = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "spi_flash_part0";
+ reg = <0x0 0x800000>;
+ };
+
+ parition@1 {
+ label = "spi_flash_part1";
+ reg = <0x800000 0x700000>;
+ };
+
+ parition@2 {
+ label = "spi_flash_part2";
+ reg = <0xF00000 0x100000>;
+ };
+ };
+};
+
+&usb1 {
+ compatible = "chipidea,usb2";
+ phys = <&usb1phy>;
+ phy-names = "usb-phy";
+ dr_mode = "peripheral";
+};
+
--
2.35.1
Powered by blists - more mailing lists