| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20220430162353.607709-2-konrad.dybcio@somainline.org>
Date: Sat, 30 Apr 2022 18:23:40 +0200
From: Konrad Dybcio <konrad.dybcio@...ainline.org>
To: ~postmarketos/upstreaming@...ts.sr.ht
Cc: martin.botka@...ainline.org,
angelogioacchino.delregno@...ainline.org,
marijn.suijten@...ainline.org, jamipkettunen@...ainline.org,
Konrad Dybcio <konrad.dybcio@...ainline.org>,
Andy Gross <agross@...nel.org>,
Bjorn Andersson <bjorn.andersson@...aro.org>,
Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
linux-arm-msm@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org
Subject: [PATCH 02/14] arm64: dts: qcom: msm8998-clamshell: Clean up the DT
Keep the nodes and includes in order, clean up unnecessary properties & nodes.
Signed-off-by: Konrad Dybcio <konrad.dybcio@...ainline.org>
---
.../boot/dts/qcom/msm8998-clamshell.dtsi | 118 ++++++++++--------
arch/arm64/boot/dts/qcom/pm8005.dtsi | 4 +
2 files changed, 73 insertions(+), 49 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi
index 6e70c1ead5e1..a8756bcdad3b 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi
@@ -8,13 +8,10 @@
*/
#include "msm8998.dtsi"
-#include "pm8998.dtsi"
#include "pm8005.dtsi"
+#include "pm8998.dtsi"
/ {
- chosen {
- };
-
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
regulator-name = "vph_pwr";
@@ -37,6 +34,28 @@ bluetooth {
};
};
+&blsp1_uart3_on {
+ rx {
+ /delete-property/ bias-disable;
+ /*
+ * Configure a pull-up on 45 (RX). This is needed to
+ * avoid garbage data when the TX pin of the Bluetooth
+ * module is in tri-state (module powered off or not
+ * driving the signal yet).
+ */
+ bias-pull-up;
+ };
+
+ cts {
+ /delete-property/ bias-disable;
+ /*
+ * Configure a pull-down on 47 (CTS) to match the pull
+ * of the Bluetooth module.
+ */
+ bias-pull-down;
+ };
+};
+
/*
* The laptop FW does not appear to support the retention state as it is
* not advertised as enabled in ACPI, and enabling it in DT can cause boot
@@ -82,20 +101,16 @@ &pcie_phy {
status = "okay";
};
-&pm8005_lsid1 {
- pm8005-regulators {
- compatible = "qcom,pm8005-regulators";
-
- vdd_s1-supply = <&vph_pwr>;
+&pm8005_regulators {
+ vdd_s1-supply = <&vph_pwr>;
- pm8005_s1: s1 { /* VDD_GFX supply */
- regulator-min-microvolt = <524000>;
- regulator-max-microvolt = <1100000>;
- regulator-enable-ramp-delay = <500>;
+ pm8005_s1: s1 { /* VDD_GFX supply */
+ regulator-min-microvolt = <524000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-enable-ramp-delay = <500>;
- /* hack until we rig up the gpu consumer */
- regulator-always-on;
- };
+ /* hack until we rig up the gpu consumer */
+ regulator-always-on;
};
};
@@ -143,127 +158,156 @@ vreg_s3a_1p35: s3 {
regulator-min-microvolt = <1352000>;
regulator-max-microvolt = <1352000>;
};
+
vreg_s4a_1p8: s4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-allow-set-load;
};
+
vreg_s5a_2p04: s5 {
regulator-min-microvolt = <1904000>;
regulator-max-microvolt = <2040000>;
};
+
vreg_s7a_1p025: s7 {
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1028000>;
};
+
vreg_l1a_0p875: l1 {
regulator-min-microvolt = <880000>;
regulator-max-microvolt = <880000>;
regulator-allow-set-load;
};
+
vreg_l2a_1p2: l2 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-allow-set-load;
};
+
vreg_l3a_1p0: l3 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
};
+
vreg_l5a_0p8: l5 {
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <800000>;
};
+
vreg_l6a_1p8: l6 {
regulator-min-microvolt = <1808000>;
regulator-max-microvolt = <1808000>;
};
+
vreg_l7a_1p8: l7 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-allow-set-load;
};
+
vreg_l8a_1p2: l8 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
+
vreg_l9a_1p8: l9 {
regulator-min-microvolt = <1808000>;
regulator-max-microvolt = <2960000>;
};
+
vreg_l10a_1p8: l10 {
regulator-min-microvolt = <1808000>;
regulator-max-microvolt = <2960000>;
};
+
vreg_l11a_1p0: l11 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
};
+
vreg_l12a_1p8: l12 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
+
vreg_l13a_2p95: l13 {
regulator-min-microvolt = <1808000>;
regulator-max-microvolt = <2960000>;
};
+
vreg_l14a_1p88: l14 {
regulator-min-microvolt = <1880000>;
regulator-max-microvolt = <1880000>;
};
+
vreg_l15a_1p8: l15 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
+
vreg_l16a_2p7: l16 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2704000>;
};
+
vreg_l17a_1p3: l17 {
regulator-min-microvolt = <1304000>;
regulator-max-microvolt = <1304000>;
regulator-allow-set-load;
};
+
vreg_l18a_2p7: l18 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2704000>;
};
+
vreg_l19a_3p0: l19 {
regulator-min-microvolt = <3008000>;
regulator-max-microvolt = <3008000>;
};
+
vreg_l20a_2p95: l20 {
regulator-min-microvolt = <2960000>;
regulator-max-microvolt = <2960000>;
regulator-allow-set-load;
};
+
vreg_l21a_2p95: l21 {
regulator-min-microvolt = <2960000>;
regulator-max-microvolt = <2960000>;
regulator-allow-set-load;
regulator-system-load = <800000>;
};
+
vreg_l22a_2p85: l22 {
regulator-min-microvolt = <2864000>;
regulator-max-microvolt = <2864000>;
};
+
vreg_l23a_3p3: l23 {
regulator-min-microvolt = <3312000>;
regulator-max-microvolt = <3312000>;
};
+
vreg_l24a_3p075: l24 {
regulator-min-microvolt = <3088000>;
regulator-max-microvolt = <3088000>;
};
+
vreg_l25a_3p3: l25 {
regulator-min-microvolt = <3104000>;
regulator-max-microvolt = <3312000>;
regulator-allow-set-load;
};
+
vreg_l26a_1p2: l26 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
+
vreg_l28_3p0: l28 {
regulator-min-microvolt = <3008000>;
regulator-max-microvolt = <3008000>;
@@ -278,7 +322,6 @@ vreg_lvs2a_1p8: lvs2 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
-
};
};
@@ -286,15 +329,6 @@ &remoteproc_mss {
status = "okay";
};
-&tlmm {
- gpio-reserved-ranges = <0 4>, <81 4>;
-
- touchpad: touchpad-pin {
- pins = "gpio123";
- bias-pull-up;
- };
-};
-
&sdhc2 {
status = "okay";
@@ -306,6 +340,15 @@ &sdhc2 {
pinctrl-1 = <&sdc2_off &sdc2_cd>;
};
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <81 4>;
+
+ touchpad: touchpad-pin {
+ pins = "gpio123";
+ bias-pull-up;
+ };
+};
+
&ufshc {
status = "okay";
};
@@ -339,26 +382,3 @@ &wifi {
vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
};
-
-/* PINCTRL - board-specific pinctrl */
-&blsp1_uart3_on {
- rx {
- /delete-property/ bias-disable;
- /*
- * Configure a pull-up on 45 (RX). This is needed to
- * avoid garbage data when the TX pin of the Bluetooth
- * module is in tri-state (module powered off or not
- * driving the signal yet).
- */
- bias-pull-up;
- };
-
- cts {
- /delete-property/ bias-disable;
- /*
- * Configure a pull-down on 47 (CTS) to match the pull
- * of the Bluetooth module.
- */
- bias-pull-down;
- };
-};
diff --git a/arch/arm64/boot/dts/qcom/pm8005.dtsi b/arch/arm64/boot/dts/qcom/pm8005.dtsi
index 3f97607d8baa..50fb6c753bf8 100644
--- a/arch/arm64/boot/dts/qcom/pm8005.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8005.dtsi
@@ -28,5 +28,9 @@ pm8005_lsid1: pmic@5 {
reg = <0x5 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
+
+ pm8005_regulators: regulators {
+ compatible = "qcom,pm8005-regulators";
+ };
};
};
--
2.35.2
Powered by blists - more mailing lists