Message-ID: <773f5323-43af-6764-ea74-2a3bac2022e8@opensource.wdc.com>
Date:   Wed, 4 May 2022 05:29:23 +0900
From:   Damien Le Moal <damien.lemoal@...nsource.wdc.com>
To:     Serge Semin <Sergey.Semin@...kalelectronics.ru>,
        Hans de Goede <hdegoede@...hat.com>,
        Jens Axboe <axboe@...nel.dk>, Rob Herring <robh+dt@...nel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>
Cc:     Serge Semin <fancer.lancer@...il.com>,
        Alexey Malahov <Alexey.Malahov@...kalelectronics.ru>,
        Pavel Parkhomenko <Pavel.Parkhomenko@...kalelectronics.ru>,
        linux-ide@...r.kernel.org, linux-kernel@...r.kernel.org,
        devicetree@...r.kernel.org
Subject: Re: [PATCH v2 02/23] dt-bindings: ata: ahci-platform: Detach common
 AHCI bindings

On 2022/05/04 5:09, Serge Semin wrote:
> In order to create a more sophisticated AHCI controller DT bindings let's
> divide the already available generic AHCI platform YAML schema into the
> platform part and a set of the common AHCI properties. The former part
> will be used to evaluate the AHCI DT nodes mainly compatible with the
> generic AHCI controller while the later schema will be used for more
> thorough AHCI DT nodes description. For instance such YAML schemas design
> will be useful for our DW AHCI SATA controller derivative with four clock
> sources, two reset lines, one system controller reference and specific
> max Rx/Tx DMA xfers size constraints.
> 
> Note the phys and target-supply property requirement is preserved in the
> generic AHCI platform bindings because some platforms can lack of the
> explicitly specified PHYs or target device power regulators.
> 
> Signed-off-by: Serge Semin <Sergey.Semin@...kalelectronics.ru>
> 
> ---
> 
> Folks, I don't really see why the phys/target-supply requirement has been
> added to the generic AHCI DT schema in the first place. Probably just to
> imply some meaning for the sub-nodes definition. Anyway in one of the
> further patches I am adding the DW AHCI SATA controller DT bindings which
> won't require having these properties specified in the sub-nodes, but will
> describe additional port-specific properties. That's why I get to keep the
> constraints in the ahci-platform.yaml schema instead of moving them to the
> common schema.
> 
> Changelog v2:
> - This is a new patch created after rebasing v1 onto the 5.18-rc3 kernel.
> ---
>  .../devicetree/bindings/ata/ahci-common.yaml  | 117 ++++++++++++++++++
>  .../bindings/ata/ahci-platform.yaml           |  68 +---------
>  2 files changed, 123 insertions(+), 62 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/ata/ahci-common.yaml
> 
> diff --git a/Documentation/devicetree/bindings/ata/ahci-common.yaml b/Documentation/devicetree/bindings/ata/ahci-common.yaml
> new file mode 100644
> index 000000000000..72e24b246040
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/ata/ahci-common.yaml
> @@ -0,0 +1,117 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/ata/ahci-common.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Common Properties for Serial ATA AHCI controllers
> +
> +maintainers:
> +  - Hans de Goede <hdegoede@...hat.com>
> +  - Jens Axboe <axboe@...nel.dk>

This should probably be me rather than Jens since Jens is no longer maintaining
libata/ahci.

> +
> +description:
> +  This document defines device tree properties for a common AHCI SATA
> +  controller implementation. It's hardware interface is supposed to
> +  conform to the technical standard defined by Intel (see Serial ATA
> +  Advanced Host Controller Interface specification for details). The
> +  document doesn't constitute a DT-node binding by itself but merely
> +  defines a set of common properties for the AHCI-compatible devices.
> +
> +select: false
> +
> +allOf:
> +  - $ref: sata-common.yaml#
> +
> +properties:
> +  reg:
> +    description:
> +      Generic AHCI registers space conforming to the Serial ATA AHCI
> +      specification.
> +
> +  reg-names:
> +    description: CSR space IDs
> +
> +  interrupts:
> +    description:
> +      Generic AHCI state change interrupt. Can be implemented either as a
> +      single line attached to the controller as a set of the dedicated signals
> +      for the global and particular port events.
> +
> +  clocks:
> +    description:
> +      List of all the reference clocks connected to the controller.
> +
> +  clock-names:
> +    description: Reference clocks IDs
> +
> +  resets:
> +    description:
> +      List of the reset control lines to reset the controller clock
> +      domains.
> +
> +  reset-names:
> +    description: Reset line IDs
> +
> +  power-domains:
> +    description:
> +      List of the power domain the AHCI controller being a part of.
> +
> +  ahci-supply:
> +    description: Power regulator for AHCI controller
> +
> +  target-supply:
> +    description: Power regulator for SATA target device
> +
> +  phy-supply:
> +    description: Power regulator for SATA PHY
> +
> +  phys:
> +    description: Reference to the SATA PHY node
> +    maxItems: 1
> +
> +  phy-names:
> +    maxItems: 1
> +
> +  ports-implemented:
> +    $ref: '/schemas/types.yaml#/definitions/uint32'
> +    description:
> +      Mask that indicates which ports the HBA supports. Useful if PI is not
> +      programmed by the BIOS, which is true for some embedded SoC's.
> +    maximum: 0x1f
> +
> +patternProperties:
> +  "^sata-port@[0-9a-f]+$":
> +    type: object
> +    description:
> +      It is optionally possible to describe the ports as sub-nodes so
> +      to enable each port independently when dealing with multiple PHYs.
> +
> +    properties:
> +      reg:
> +        description: AHCI SATA port identifier
> +        maxItems: 1
> +
> +      phys:
> +        description: Individual AHCI SATA port PHY
> +        maxItems: 1
> +
> +      phy-names:
> +        description: AHCI SATA port PHY ID
> +        maxItems: 1
> +
> +      target-supply:
> +        description: Power regulator for SATA port target device
> +
> +    required:
> +      - reg
> +
> +    additionalProperties: true
> +
> +required:
> +  - reg
> +  - interrupts
> +
> +additionalProperties: true
> +
> +...
> diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.yaml b/Documentation/devicetree/bindings/ata/ahci-platform.yaml
> index 9304e4731965..76075d3c8987 100644
> --- a/Documentation/devicetree/bindings/ata/ahci-platform.yaml
> +++ b/Documentation/devicetree/bindings/ata/ahci-platform.yaml
> @@ -36,8 +36,7 @@ select:
>      - compatible
>  
>  allOf:
> -  - $ref: "sata-common.yaml#"
> -
> +  - $ref: "ahci-common.yaml#"
>  
>  properties:
>    compatible:
> @@ -69,90 +68,35 @@ properties:
>      maxItems: 1
>  
>    clocks:
> -    description:
> -      Clock IDs array as required by the controller.
>      minItems: 1
>      maxItems: 3
>  
>    clock-names:
> -    description:
> -      Names of clocks corresponding to IDs in the clock property.
>      minItems: 1
>      maxItems: 3
>  
>    interrupts:
>      maxItems: 1
>  
> -  ahci-supply:
> -    description:
> -      regulator for AHCI controller
> -
> -  phy-supply:
> -    description:
> -      regulator for PHY power
> -
> -  phys:
> -    description:
> -      List of all PHYs on this controller
> -    maxItems: 1
> -
> -  phy-names:
> -    description:
> -      Name specifier for the PHYs
> -    maxItems: 1
> -
> -  ports-implemented:
> -    $ref: '/schemas/types.yaml#/definitions/uint32'
> -    description: |
> -      Mask that indicates which ports that the HBA supports
> -      are available for software to use. Useful if PORTS_IMPL
> -      is not programmed by the BIOS, which is true with
> -      some embedded SoCs.
> -    maximum: 0x1f
> -
>    power-domains:
>      maxItems: 1
>  
>    resets:
>      maxItems: 1
>  
> -  target-supply:
> -    description:
> -      regulator for SATA target power
> -
> -required:
> -  - compatible
> -  - reg
> -  - interrupts
> -
>  patternProperties:
>    "^sata-port@[0-9a-f]+$":
>      type: object
> -    additionalProperties: false
> -    description:
> -      Subnode with configuration of the Ports.
> -
> -    properties:
> -      reg:
> -        maxItems: 1
> -
> -      phys:
> -        maxItems: 1
> -
> -      phy-names:
> -        maxItems: 1
> -
> -      target-supply:
> -        description:
> -          regulator for SATA target power
> -
> -    required:
> -      - reg
>  
>      anyOf:
>        - required: [ phys ]
>        - required: [ target-supply ]
>  
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +
>  unevaluatedProperties: false
>  
>  examples:


-- 
Damien Le Moal
Western Digital Research

Powered by blists - more mailing lists