| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20220512124905.49979-9-robert.marko@sartura.hr>
Date: Thu, 12 May 2022 14:49:03 +0200
From: Robert Marko <robert.marko@...tura.hr>
To: robh+dt@...nel.org, krzysztof.kozlowski+dt@...aro.org,
andrew@...n.ch, gregory.clement@...tlin.com,
sebastian.hesselbarth@...il.com, kostap@...vell.com,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org
Cc: Robert Marko <robert.marko@...tura.hr>
Subject: [PATCH v3 09/11] arm64: dts: marvell: split Methode uDPU DTS
Split the Methode uDPU DTS into a common DTSI as preparation for adding
support for Methode eDPU which is based on the uDPU to avoid duplication.
Signed-off-by: Robert Marko <robert.marko@...tura.hr>
---
.../boot/dts/marvell/armada-3720-uDPU.dts | 150 +---------------
.../boot/dts/marvell/armada-3720-uDPU.dtsi | 160 ++++++++++++++++++
2 files changed, 161 insertions(+), 149 deletions(-)
create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-uDPU.dtsi
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
index f21a855fc608..a75734d88a4f 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
@@ -1,66 +1,13 @@
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Device tree for the uDPU board.
- * Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
- * Copyright (C) 2016 Marvell
- * Copyright (C) 2019 Methode Electronics
- * Copyright (C) 2019 Telus
- *
- * Vladimir Vid <vladimir.vid@...tura.hr>
- */
/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include "armada-372x.dtsi"
+#include "armada-3720-uDPU.dtsi"
/ {
model = "Methode uDPU Board";
compatible = "methode,udpu", "marvell,armada3720", "marvell,armada3710";
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- memory@0 {
- device_type = "memory";
- reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
- };
-
- leds {
- compatible = "gpio-leds";
-
- led-power1 {
- label = "udpu:green:power";
- gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
- };
-
- led-power2 {
- label = "udpu:red:power";
- gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
- };
-
- led-network1 {
- label = "udpu:green:network";
- gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
- };
-
- led-network2 {
- label = "udpu:red:network";
- gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
- };
-
- led-alarm1 {
- label = "udpu:green:alarm";
- gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
- };
-
- led-alarm2 {
- label = "udpu:red:alarm";
- gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
- };
- };
-
sfp_eth0: sfp-eth0 {
compatible = "sff,sfp";
i2c-bus = <&i2c0>;
@@ -70,55 +17,6 @@ sfp_eth0: sfp-eth0 {
tx-fault-gpio = <&gpiosb 5 GPIO_ACTIVE_HIGH>;
maximum-power-milliwatt = <3000>;
};
-
- sfp_eth1: sfp-eth1 {
- compatible = "sff,sfp";
- i2c-bus = <&i2c1>;
- los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
- mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
- tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
- tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
- maximum-power-milliwatt = <3000>;
- };
-};
-
-&sdhci0 {
- status = "okay";
- bus-width = <8>;
- mmc-ddr-1_8v;
- mmc-hs400-1_8v;
- marvell,pad-type = "fixed-1-8v";
- non-removable;
- no-sd;
- no-sdio;
-};
-
-&spi0 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&spi_quad_pins>;
-
- flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <54000000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "firmware";
- reg = <0x0 0x180000>;
- };
-
- partition@...000 {
- label = "u-boot-env";
- reg = <0x180000 0x10000>;
- };
- };
- };
};
&pinctrl_nb {
@@ -126,11 +24,6 @@ i2c1_recovery_pins: i2c1-recovery-pins {
groups = "i2c1";
function = "gpio";
};
-
- i2c2_recovery_pins: i2c2-recovery-pins {
- groups = "i2c2";
- function = "gpio";
- };
};
&i2c0 {
@@ -143,48 +36,7 @@ &i2c0 {
sda-gpios = <&gpionb 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
};
-&i2c1 {
- status = "okay";
- pinctrl-names = "default", "recovery";
- pinctrl-0 = <&i2c2_pins>;
- pinctrl-1 = <&i2c2_recovery_pins>;
- /delete-property/mrvl,i2c-fast-mode;
- scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-
- temp-sensor@48 {
- compatible = "ti,tmp75c";
- reg = <0x48>;
- };
-
- temp-sensor@49 {
- compatible = "ti,tmp75c";
- reg = <0x49>;
- };
-};
-
ð0 {
phy-mode = "sgmii";
- status = "okay";
- managed = "in-band-status";
- phys = <&comphy1 0>;
sfp = <&sfp_eth0>;
};
-
-ð1 {
- phy-mode = "sgmii";
- status = "okay";
- managed = "in-band-status";
- phys = <&comphy0 1>;
- sfp = <&sfp_eth1>;
-};
-
-&usb3 {
- status = "okay";
- phys = <&usb2_utmi_otg_phy>;
- phy-names = "usb2-utmi-otg-phy";
-};
-
-&uart0 {
- status = "okay";
-};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dtsi b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dtsi
new file mode 100644
index 000000000000..3f79923376fb
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dtsi
@@ -0,0 +1,160 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device tree for the uDPU board.
+ * Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
+ * Copyright (C) 2016 Marvell
+ * Copyright (C) 2019 Methode Electronics
+ * Copyright (C) 2019 Telus
+ *
+ * Vladimir Vid <vladimir.vid@...tura.hr>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-372x.dtsi"
+
+/ {
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-power1 {
+ label = "udpu:green:power";
+ gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
+ };
+
+ led-power2 {
+ label = "udpu:red:power";
+ gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
+ };
+
+ led-network1 {
+ label = "udpu:green:network";
+ gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
+ };
+
+ led-network2 {
+ label = "udpu:red:network";
+ gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
+ };
+
+ led-alarm1 {
+ label = "udpu:green:alarm";
+ gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
+ };
+
+ led-alarm2 {
+ label = "udpu:red:alarm";
+ gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ sfp_eth1: sfp-eth1 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c1>;
+ los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
+ tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
+ maximum-power-milliwatt = <3000>;
+ };
+};
+
+&sdhci0 {
+ status = "okay";
+ bus-width = <8>;
+ mmc-ddr-1_8v;
+ mmc-hs400-1_8v;
+ marvell,pad-type = "fixed-1-8v";
+ non-removable;
+ no-sd;
+ no-sdio;
+};
+
+&spi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_quad_pins>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <54000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "firmware";
+ reg = <0x0 0x180000>;
+ };
+
+ partition@...000 {
+ label = "u-boot-env";
+ reg = <0x180000 0x10000>;
+ };
+ };
+ };
+};
+
+&pinctrl_nb {
+ i2c2_recovery_pins: i2c2-recovery-pins {
+ groups = "i2c2";
+ function = "gpio";
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ pinctrl-names = "default", "recovery";
+ pinctrl-0 = <&i2c2_pins>;
+ pinctrl-1 = <&i2c2_recovery_pins>;
+ /delete-property/mrvl,i2c-fast-mode;
+ scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+ temp-sensor@48 {
+ compatible = "ti,tmp75c";
+ reg = <0x48>;
+ };
+
+ temp-sensor@49 {
+ compatible = "ti,tmp75c";
+ reg = <0x49>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ managed = "in-band-status";
+ phys = <&comphy1 0>;
+};
+
+ð1 {
+ phy-mode = "sgmii";
+ status = "okay";
+ managed = "in-band-status";
+ phys = <&comphy0 1>;
+ sfp = <&sfp_eth1>;
+};
+
+&usb3 {
+ status = "okay";
+ phys = <&usb2_utmi_otg_phy>;
+ phy-names = "usb2-utmi-otg-phy";
+};
+
+&uart0 {
+ status = "okay";
+};
--
2.36.1
Powered by blists - more mailing lists