| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20220520120212.3589911-1-David_Wang6097@jabil.com>
Date: Fri, 20 May 2022 20:02:12 +0800
From: David Wang <David_Wang6097@...il.com>
To: <linux-kernel@...r.kernel.org>, <robh+dt@...nel.org>,
<krzysztof.kozlowski+dt@...aro.org>, <devicetree@...r.kernel.org>
CC: <edward_chen@...il.com>, <David_Wang6097@...il.com>
Subject: [PATCH v2] ARM: dts: aspeed: Adding Jabil Rubypass BMC
The initial introduction of the jabil server with AST2600 BMC SoC.
Signed-off-by: David Wang <David_Wang6097@...il.com>
---
arch/arm/boot/dts/Makefile | 3 +-
.../boot/dts/aspeed-bmc-jabil-rubypass.dts | 479 ++++++++++++++++++
2 files changed, 481 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7c16f8a2b738..9c395178fc89 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1566,4 +1566,5 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-bmc-tyan-s8036.dtb \
aspeed-bmc-vegman-n110.dtb \
aspeed-bmc-vegman-rx20.dtb \
- aspeed-bmc-vegman-sx20.dtb
+ aspeed-bmc-vegman-sx20.dtb \
+ aspeed-bmc-jabil-rubypass.dtb
diff --git a/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
new file mode 100644
index 000000000000..5e46af30c9e9
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
@@ -0,0 +1,479 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+ model = "Jabil rbp";
+ compatible = "jabil,rbp", "aspeed,ast2600";
+
+ chosen {
+ bootargs = "console=ttyS4,115200n8";
+ };
+
+ memory@...00000 {
+ device_type = "memory";
+ reg = <0x80000000 0x80000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ gfx_memory: framebuffer {
+ size = <0x01000000>;
+ alignment = <0x01000000>;
+ compatible = "shared-dma-pool";
+ reusable;
+ };
+ };
+
+ vcc_sdhci0: regulator-vcc-sdhci0 {
+ compatible = "regulator-fixed";
+ regulator-name = "SDHCI0 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&gpio0 ASPEED_GPIO(V, 0) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+
+ vccq_sdhci0: regulator-vccq-sdhci0 {
+ compatible = "regulator-gpio";
+ regulator-name = "SDHCI0 VccQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&gpio0 ASPEED_GPIO(V, 1) GPIO_ACTIVE_HIGH>;
+ gpios-states = <1>;
+ states = <3300000 1>,
+ <1800000 0>;
+ };
+
+ vcc_sdhci1: regulator-vcc-sdhci1 {
+ compatible = "regulator-fixed";
+ regulator-name = "SDHCI1 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&gpio0 ASPEED_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vccq_sdhci1: regulator-vccq-sdhci1 {
+ compatible = "regulator-gpio";
+ regulator-name = "SDHCI1 VccQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&gpio0 ASPEED_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
+ gpios-states = <1>;
+ states = <3300000 1>,
+ <1800000 0>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ identify {
+ default-state = "off";
+ gpios = <&gpio0 ASPEED_GPIO(B, 7) GPIO_ACTIVE_LOW>;
+ };
+
+ status_amber {
+ default-state = "off";
+ gpios = <&gpio0 ASPEED_GPIO(G, 3) GPIO_ACTIVE_LOW>;
+ };
+
+ status_green {
+ default-state = "keep";
+ gpios = <&gpio0 ASPEED_GPIO(G, 2) GPIO_ACTIVE_LOW>;
+ };
+
+ status_susack {
+ default-state = "off";
+ gpios = <&gpio0 ASPEED_GPIO(V, 6) GPIO_ACTIVE_LOW>;
+ };
+
+ fan1_fault{
+ default-state = "off";
+ gpios = <&gpio3_71 0 GPIO_ACTIVE_HIGH>;
+ };
+ fan2_fault{
+ default-state = "off";
+ };
+ fan3_fault{
+ default-state = "off";
+ gpios = <&gpio3_71 2 GPIO_ACTIVE_HIGH>;
+ };
+ fan4_fault{
+ default-state = "off";
+ gpios = <&gpio3_71 3 GPIO_ACTIVE_HIGH>;
+ };
+ fan5_fault{
+ default-state = "off";
+ gpios = <&gpio3_71 4 GPIO_ACTIVE_HIGH>;
+ };
+ fan6_fault{
+ default-state = "off";
+ gpios = <&gpio3_71 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ power_amber {
+ default-state = "off";
+ gpios = <&gpio0 ASPEED_GPIO(Y, 0) GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ ethphy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+};
+
+&mdio1 {
+ status = "okay";
+
+ ethphy1: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+};
+
+&mdio2 {
+ status = "okay";
+
+ ethphy2: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+};
+
+&mdio3 {
+ status = "okay";
+
+ ethphy3: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+};
+
+&mac0 {
+ status = "okay";
+
+ phy-mode = "rgmii-rxid";
+ phy-handle = <ðphy0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rgmii1_default>;
+};
+
+
+&mac1 {
+ status = "okay";
+
+ phy-mode = "rgmii-rxid";
+ phy-handle = <ðphy1>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rgmii2_default>;
+};
+
+&mac2 {
+ status = "okay";
+
+ phy-mode = "rgmii";
+ phy-handle = <ðphy2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rgmii3_default>;
+};
+
+&mac3 {
+ status = "okay";
+
+ phy-mode = "rgmii";
+ phy-handle = <ðphy3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rgmii4_default>;
+};
+
+&emmc_controller {
+ status = "okay";
+};
+
+&emmc {
+ non-removable;
+ bus-width = <4>;
+ max-frequency = <100000000>;
+ clk-phase-mmc-hs200 = <9>, <225>;
+};
+
+&rtc {
+ status = "okay";
+};
+
+&fmc {
+ status = "okay";
+ flash@0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "bmc";
+ spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+ };
+};
+
+&spi1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi1_default>;
+
+ flash@0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "pnor";
+ spi-max-frequency = <100000000>;
+ };
+};
+
+&uart1 {
+ status = "okay";
+ pinctrl-0 = <&pinctrl_txd1_default
+ &pinctrl_rxd1_default
+ &pinctrl_nrts1_default
+ &pinctrl_ndtr1_default
+ &pinctrl_ndsr1_default
+ &pinctrl_ncts1_default
+ &pinctrl_ndcd1_default
+ &pinctrl_nri1_default>;
+};
+
+&uart2 {
+ status = "okay";
+ pinctrl-0 = <&pinctrl_txd2_default
+ &pinctrl_rxd2_default
+ &pinctrl_nrts2_default
+ &pinctrl_ndtr2_default
+ &pinctrl_ndsr2_default
+ &pinctrl_ncts2_default
+ &pinctrl_ndcd2_default
+ &pinctrl_nri2_default>;
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&uart4 {
+ status = "okay";
+};
+
+
+&i2c0 {
+ status = "okay";
+
+ temp@2e {
+ compatible = "adi,adt7490";
+ reg = <0x2e>;
+ };
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c3 {
+ multi-master;
+ status = "okay";
+
+ gpio@70 {
+ compatible = "nxp,pca9538";
+ reg = <0x70>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(O, 7) IRQ_TYPE_EDGE_FALLING>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "presence-fan1-n", "presence-fan2-n", "presence-fan3-n", "presence-fan4-n",
+ "presence-fan5-n", "presence-fan6-n", "", "";
+ };
+
+ gpio3_71:gpio@71 {
+ compatible = "nxp,pca9538";
+ reg = <0x71>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "led-fan1-fault", "led-fan2-fault", "led-fan3-fault", "led-fan4-fault",
+ "led-fan5-fault", "led-fan6-fault", "", "";
+ };
+};
+
+&i2c4 {
+ status = "okay";
+};
+
+&i2c5 {
+ status = "okay";
+};
+
+&i2c6 {
+ status = "okay";
+};
+
+&i2c7 {
+ status = "okay";
+};
+
+&i2c8 {
+ status = "okay";
+};
+
+&i2c9 {
+ status = "okay";
+};
+
+&i2c12 {
+ status = "okay";
+};
+
+&i2c13 {
+ status = "okay";
+};
+
+&i2c14 {
+ status = "okay";
+};
+
+&i2c15 {
+ status = "okay";
+};
+
+&fsim0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&uhci {
+ status = "okay";
+};
+
+&sdc {
+ status = "okay";
+};
+
+/*
+ * The signal voltage of sdhci0 and sdhci1 on AST2600-A2 EVB is able to be
+ * toggled by GPIO pins.
+ * In the reference design, GPIOV0 of AST2600-A2 EVB is connected to the
+ * power load switch that provides 3.3v to sdhci0 vdd, GPIOV1 is connected to
+ * a 1.8v and a 3.3v power load switch that provides signal voltage to
+ * sdhci0 bus.
+ * If GPIOV0 is active high, sdhci0 is enabled, otherwise, sdhci0 is disabled.
+ * If GPIOV1 is active high, 3.3v power load switch is enabled, sdhci0 signal
+ * voltage is 3.3v, otherwise, 1.8v power load switch will be enabled,
+ * sdhci0 signal voltage becomes 1.8v.
+ * AST2600-A2 EVB also supports toggling signal voltage for sdhci1.
+ * The design is the same as sdhci0, it uses GPIOV2 as power-gpio and GPIOV3
+ * as power-switch-gpio.
+ */
+&sdhci0 {
+ status = "okay";
+ bus-width = <4>;
+ max-frequency = <100000000>;
+ sdhci-drive-type = /bits/ 8 <3>;
+ sdhci-caps-mask = <0x7 0x0>;
+ sdhci,wp-inverted;
+ vmmc-supply = <&vcc_sdhci0>;
+ vqmmc-supply = <&vccq_sdhci0>;
+ clk-phase-sd-hs = <7>, <200>;
+};
+
+&sdhci1 {
+ status = "okay";
+ bus-width = <4>;
+ max-frequency = <100000000>;
+ sdhci-drive-type = /bits/ 8 <3>;
+ sdhci-caps-mask = <0x7 0x0>;
+ sdhci,wp-inverted;
+ vmmc-supply = <&vcc_sdhci1>;
+ vqmmc-supply = <&vccq_sdhci1>;
+ clk-phase-sd-hs = <7>, <200>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gfx {
+ status = "okay";
+ memory-region = <&gfx_memory>;
+};
+
+&gpio0 {
+ status = "okay";
+ gpio-line-names =
+ /*A0-A7*/ "","","","","","","","",
+ /*B0-B7*/ "presence-ncsi-i210-n","","","","","","","led-identify-n",
+ /*C0-C7*/ "","","","","","","","",
+ /*D0-D7*/ "","","","","","","","",
+ /*E0-E7*/ "","","","","","","","",
+ /*F0-F7*/ "","","","","","","id-button","",
+ /*G0-G7*/ "","","led-status-green-n","led-status-amber-n","","","","",
+ /*H0-H7*/ "","","","","","cpu-caterr","","cpu1-caterr-n",
+ /*I0-I7*/ "","","","","","","","",
+ /*J0-J7*/ "","","","","","","","",
+ /*K0-K7*/ "","","","","","","","",
+ /*L0-L7*/ "","","","","","","","",
+ /*M0-M7*/ "","","","","","","","",
+ /*N0-N7*/ "","","","","","","","",
+ /*O0-O7*/ "","","","","","","nmi-button","",
+ /*P0-P7*/ "reset-button","reset-out","power-button","power-out","","","","led-hartbeat-n",
+ /*Q0-Q7*/ "","","","","","","","",
+ /*R0-R7*/ "","","","","","","","",
+ /*S0-S7*/ "","","","","","","","",
+ /*T0-T7*/ "","","","","","","","",
+ /*U0-U7*/ "","","","","","","","",
+ /*V0-V7*/ "regulator-vcc-sdhci0","regulator-vccq-sdhci0","regulator-vcc-sdhci1","regulator-vccq-sdhci1","sio-power-good","led-bmc-fw-config-done-n","","",
+ /*W0-W7*/ "","","","","","","","",
+ /*X0-X7*/ "cpu-err2","","","","","","","",
+ /*Y0-Y7*/ "led-power-amber","","","","","","","",
+ /*Z0-Z7*/ "cpu-err0","cpu-err1","","","","","","";
+ };
+
+&gpio1 {
+ status = "okay";
+};
+
+&kcs3 {
+ aspeed,lpc-io-reg = <0xCA2>;
+ status = "okay";
+};
+
+&kcs4 {
+ aspeed,lpc-io-reg = <0xCA4>;
+ status = "okay";
+};
+
+&lpc_snoop {
+ snoop-ports = <0x80>;
+ status = "okay";
+};
+
--
2.30.2
Powered by blists - more mailing lists