linux-kernel - [PATCH v6 5/5] i2c: npcm: Capitalize the one-line comment

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <20220525032341.3182-6-warp5tw@gmail.com>
Date:   Wed, 25 May 2022 11:23:41 +0800
From:   Tyrone Ting <warp5tw@...il.com>
To:     avifishman70@...il.com, tmaimon77@...il.com, tali.perry1@...il.com,
        venture@...gle.com, yuenn@...gle.com, benjaminfair@...gle.com,
        robh+dt@...nel.org, krzysztof.kozlowski+dt@...aro.org,
        wsa@...nel.org, andriy.shevchenko@...ux.intel.com,
        jarkko.nikula@...ux.intel.com, semen.protsenko@...aro.org,
        jie.deng@...el.com, jsd@...ihalf.com, sven@...npeter.dev,
        lukas.bulwahn@...il.com, olof@...om.net, arnd@...db.de,
        warp5tw@...il.com, tali.perry@...oton.com, Avi.Fishman@...oton.com,
        tomer.maimon@...oton.com, KWLIU@...oton.com, JJLIU0@...oton.com,
        kfting@...oton.com
Cc:     openbmc@...ts.ozlabs.org, linux-i2c@...r.kernel.org,
        devicetree@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: [PATCH v6 5/5] i2c: npcm: Capitalize the one-line comment

From: Tyrone Ting <kfting@...oton.com>

Make the one-line comments capital in the driver to get the comment style
consistent.

Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tyrone Ting <kfting@...oton.com>
---
 drivers/i2c/busses/i2c-npcm7xx.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/i2c/busses/i2c-npcm7xx.c b/drivers/i2c/busses/i2c-npcm7xx.c
index 86fd942ea648..7d863edc14e4 100644
--- a/drivers/i2c/busses/i2c-npcm7xx.c
+++ b/drivers/i2c/busses/i2c-npcm7xx.c
@@ -680,7 +680,7 @@ static void npcm_i2c_reset(struct npcm_i2c *bus)
 	}
 #endif
 
-	/* clear status bits for spurious interrupts */
+	/* Clear status bits for spurious interrupts */
 	npcm_i2c_clear_master_status(bus);
 
 	bus->state = I2C_IDLE;
@@ -1252,7 +1252,7 @@ static irqreturn_t npcm_i2c_int_slave_handler(struct npcm_i2c *bus)
 	} /* SDAST */
 
 	/*
-	 * if irq is not one of the above, make sure EOB is disabled and all
+	 * If irq is not one of the above, make sure EOB is disabled and all
 	 * status bits are cleared.
 	 */
 	if (ret == IRQ_NONE) {
@@ -1506,7 +1506,7 @@ static void npcm_i2c_irq_handle_nack(struct npcm_i2c *bus)
 		npcm_i2c_clear_master_status(bus);
 		readx_poll_timeout_atomic(ioread8, bus->reg + NPCM_I2CCST, val,
 					  !(val & NPCM_I2CCST_BUSY), 10, 200);
-		/* verify no status bits are still set after bus is released */
+		/* Verify no status bits are still set after bus is released */
 		npcm_i2c_clear_master_status(bus);
 	}
 	bus->state = I2C_IDLE;
@@ -1974,7 +1974,7 @@ static int npcm_i2c_init_module(struct npcm_i2c *bus, enum i2c_mode mode,
 
 	npcm_i2c_reset(bus);
 
-	/* check HW is OK: SDA and SCL should be high at this point. */
+	/* Check HW is OK: SDA and SCL should be high at this point. */
 	if ((npcm_i2c_get_SDA(&bus->adap) == 0) || (npcm_i2c_get_SCL(&bus->adap) == 0)) {
 		dev_err(bus->dev, "I2C%d init fail: lines are low\n", bus->num);
 		dev_err(bus->dev, "SDA=%d SCL=%d\n", npcm_i2c_get_SDA(&bus->adap),
@@ -2034,7 +2034,7 @@ static irqreturn_t npcm_i2c_bus_irq(int irq, void *dev_id)
 			return IRQ_HANDLED;
 	}
 #endif
-	/* clear status bits for spurious interrupts */
+	/* Clear status bits for spurious interrupts */
 	npcm_i2c_clear_master_status(bus);
 
 	return IRQ_HANDLED;
@@ -2216,7 +2216,7 @@ static int npcm_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
 		 (bus->data->rxf_ctl_last_pec & ioread8(bus->reg + NPCM_I2CRXF_CTL)))
 		npcm_i2c_reset(bus);
 
-	/* after any xfer, successful or not, stall and EOB must be disabled */
+	/* After any xfer, successful or not, stall and EOB must be disabled */
 	npcm_i2c_stall_after_start(bus, false);
 	npcm_i2c_eob_int(bus, false);
 
-- 
2.17.1