linux-kernel - [PATCH v15 4/4] arm64: dts: qcom: sc7280-herobrine: Add lpi pinmux properties for CRD 3.0/3.1

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <1655108645-1517-5-git-send-email-quic_srivasam@quicinc.com>
Date:   Mon, 13 Jun 2022 13:54:05 +0530
From:   Srinivasa Rao Mandadapu <quic_srivasam@...cinc.com>
To:     <agross@...nel.org>, <bjorn.andersson@...aro.org>,
        <robh+dt@...nel.org>, <linux-arm-msm@...r.kernel.org>,
        <devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
        <quic_rohkumar@...cinc.com>, <srinivas.kandagatla@...aro.org>,
        <dianders@...omium.org>, <swboyd@...omium.org>,
        <judyhsiao@...omium.org>
CC:     Srinivasa Rao Mandadapu <quic_srivasam@...cinc.com>,
        "Venkata Prasad Potturu" <quic_potturu@...cinc.com>
Subject: [PATCH v15 4/4] arm64: dts: qcom: sc7280-herobrine: Add lpi pinmux properties for CRD 3.0/3.1

Add LPASS LPI pinctrl properties, which are required for Audio
functionality on herobrine based platforms of rev5+
(aka CRD 3.0/3.1) boards.

Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@...cinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@...cinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@...cinc.com>
Reviewed-by: Matthias Kaehlcke <mka@...omium.org>
---
 arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts | 61 +++++++++++++++++++++++
 1 file changed, 61 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
index 53feaed..d92575e 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
@@ -144,6 +144,67 @@ ap_ts_pen_1v8: &i2c13 {
  * - If a pin is totally internal to Qcard then it gets Qcard name.
  * - If a pin is not hooked up on Qcard, it gets no name.
  */
+&lpass_dmic01_clk {
+	drive-strength = <8>;
+	bias-disable;
+};
+
+&lpass_dmic01_clk_sleep {
+	drive-strength = <2>;
+};
+
+&lpass_dmic01_data {
+	bias-pull-down;
+};
+
+&lpass_dmic23_clk {
+	drive-strength = <8>;
+	bias-disable;
+};
+
+&lpass_dmic23_clk_sleep {
+	drive-strength = <2>;
+};
+
+&lpass_dmic23_data {
+	bias-pull-down;
+};
+
+&lpass_rx_swr_clk {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-disable;
+};
+
+&lpass_rx_swr_clk_sleep {
+	bias-pull-down;
+};
+
+&lpass_rx_swr_data {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-bus-hold;
+};
+
+&lpass_rx_swr_data_sleep {
+	bias-pull-down;
+};
+
+&lpass_tx_swr_clk {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-disable;
+};
+
+&lpass_tx_swr_clk_sleep {
+	bias-pull-down;
+};
+
+&lpass_tx_swr_data {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-bus-hold;
+};
 
 &pm8350c_gpios {
 	gpio-line-names = "FLASH_STROBE_1",		/* 1 */
-- 
2.7.4