linux-kernel - Re: [PATCH 1/8] serial: core: only get RS485 termination gpio if supported

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <fbce8d7e-86e-d47e-bcd8-5b99754d1d2e@linux.intel.com>
Date:   Mon, 27 Jun 2022 12:05:50 +0300 (EEST)
From:   Ilpo Järvinen <ilpo.jarvinen@...ux.intel.com>
To:     Lukas Wunner <lukas@...ner.de>
cc:     Lino Sanfilippo <LinoSanfilippo@....de>,
        Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
        Jiri Slaby <jirislaby@...nel.org>, robh+dt@...nel.org,
        krzysztof.kozlowski+dt@...aro.org,
        Andy Shevchenko <andriy.shevchenko@...ux.intel.com>,
        vz@...ia.com, linux-arm-kernel@...ts.infradead.org,
        devicetree@...r.kernel.org,
        linux-serial <linux-serial@...r.kernel.org>,
        LKML <linux-kernel@...r.kernel.org>, p.rosenberger@...bus.com,
        Lino Sanfilippo <l.sanfilippo@...bus.com>
Subject: Re: [PATCH 1/8] serial: core: only get RS485 termination gpio if
 supported

On Sat, 25 Jun 2022, Lukas Wunner wrote:

> On Wed, Jun 22, 2022 at 05:46:52PM +0200, Lino Sanfilippo wrote:
> > In uart_get_rs485_mode() only try to get a termination GPIO if RS485 bus
> > termination is supported by the driver.
> [...]
> > --- a/drivers/tty/serial/serial_core.c
> > +++ b/drivers/tty/serial/serial_core.c
> > @@ -3384,17 +3384,20 @@ int uart_get_rs485_mode(struct uart_port *port)
> >  		rs485conf->flags |= SER_RS485_RTS_AFTER_SEND;
> >  	}
> >  
> > -	/*
> > -	 * Disabling termination by default is the safe choice:  Else if many
> > -	 * bus participants enable it, no communication is possible at all.
> > -	 * Works fine for short cables and users may enable for longer cables.
> > -	 */
> > -	port->rs485_term_gpio = devm_gpiod_get_optional(dev, "rs485-term",
> > -							GPIOD_OUT_LOW);
> > -	if (IS_ERR(port->rs485_term_gpio)) {
> > -		ret = PTR_ERR(port->rs485_term_gpio);
> > -		port->rs485_term_gpio = NULL;
> > -		return dev_err_probe(dev, ret, "Cannot get rs485-term-gpios\n");
> > +	if (port->rs485_supported->flags & SER_RS485_TERMINATE_BUS) {
> 
> So I think linux-next commit be2e2cb1d281 ("serial: Sanitize rs485_struct")
> contains a mistake in that it forces drivers to set SER_RS485_TERMINATE_BUS
> in their rs485_supported->flags to allow enabling bus termination.
> 
> That's wrong because *every* rs485-capable driver can enable bus
> termination if a GPIO has been defined for that in the DT.

Do you mean every em485 using driver? Otherwise I don't see this "forces 
drivers to set" happening anywhere in the code?

You're partially right because there are other bugs in this area such 
as the one you propose a fix below. While I was making the sanitization 
series, I entirely missed some parts related to termination because 
SER_RS485_TERMINATE_BUS is seemingly not set/handled correctly by the 
core.

Another thing that looks a bug is that on subsequent call to TIOCSRS485, 
w/o SER_RS485_TERMINATE_BUS nothing happens (for non-em485 driver, that 
is)? It seems to be taken care by 2/8 of this series though, I think. But 
it should be properly marked as Fixes: ... in that case although nobody 
has complained about it so likely not a huge issue to anyone.

> In fact, another commit which was applied as part of the same series,
> ebe2cf736a04 ("serial: pl011: Fill in rs485_supported") does not set
> SER_RS485_TERMINATE_BUS in amba-pl011.c's flags and thus forbids the
> driver from enabling bus termination, even though we know there are
> products out there which support bus termination on the pl011 through
> a GPIO (Revolution Pi RevPi Compact, Revpi Flat).
>
> I think what you want to do is amend uart_get_rs485_mode() to set
> SER_RS485_TERMINATE_BUS in port->rs485_supported_flags if a GPIO
> was found in the DT.  Instead of the change proposed above.

That seems appropriate (and is a fix).

What makes it a bit complicated though is that it's a pointer currently
and what it points to is shared per driver (besides being const):
	const struct serial_rs485       *rs485_supported;
While it could be embedded into uart_port, there's the .padding which we 
might not want to bloat uart_port with. Perhaps create non-uapi struct 
kserial_rs485 w/o .padding and add static_assert()s to ensure the 
layout is identical to serial_rs485?


-- 
 i.