| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20220629041438.1352536-6-bjorn.andersson@linaro.org>
Date: Tue, 28 Jun 2022 21:14:38 -0700
From: Bjorn Andersson <bjorn.andersson@...aro.org>
To: Bjorn Andersson <bjorn.andersson@...aro.org>
Cc: Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Manivannan Sadhasivam <mani@...nel.org>,
Jassi Brar <jassisinghbrar@...il.com>,
Johan Hovold <johan@...nel.org>,
Konrad Dybcio <konrad.dybcio@...ainline.org>,
linux-arm-msm@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org,
Johan Hovold <johan+linaro@...nel.org>
Subject: [PATCH v3 5/5] arm64: dts: qcom: add SA8540P and ADP
Introduce the Qualcomm SA8540P automotive platform and the SA8295P ADP
development board.
The SA8540P and SC8280XP are fairly similar, so the SA8540P is built
ontop of the SC8280XP dtsi to reduce duplication. As more advanced
features are integrated this might be re-evaluated.
This initial contribution supports SMP, CPUFreq, cluster idle, UFS, RPMh
regulators, debug UART, PMICs, remoteprocs (NSPs crashes shortly after
booting) and USB.
The SA8295P ADP contains four PM8450 PMICs, which according to their
revid are compatible with PM8150. They are defined within the ADP for
now, to avoid creating additional .dtsi files for PM8150 with just
addresses changed - and to allow using the labels from the schematics.
Signed-off-by: Bjorn Andersson <bjorn.andersson@...aro.org>
Reviewed-by: Johan Hovold <johan+linaro@...nel.org>
---
Changes since v2:
- Sorted "status" property last throughout the patch
- Dropped empty reserved-memory node
- Dropped multiport vbus-enable pinctrl states for now
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sa8295p-adp.dts | 406 +++++++++++++++++++++++
arch/arm64/boot/dts/qcom/sa8540p.dtsi | 133 ++++++++
3 files changed, 540 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sa8295p-adp.dts
create mode 100644 arch/arm64/boot/dts/qcom/sa8540p.dtsi
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index ceeae094a59f..2f416b84b71c 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -52,6 +52,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb
dtb-$(CONFIG_ARCH_QCOM) += sa8155p-adp.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sa8295p-adp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7180-idp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r1.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r1-lte.dtb
diff --git a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
new file mode 100644
index 000000000000..d4baa2460e4a
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
@@ -0,0 +1,406 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/spmi/spmi.h>
+
+#include "sa8540p.dtsi"
+
+/ {
+ model = "Qualcomm SA8295P ADP";
+ compatible = "qcom,sa8295p-adp", "qcom,sa8540p";
+
+ aliases {
+ serial0 = &qup2_uart17;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&apps_rsc {
+ pmm8540-a-regulators {
+ compatible = "qcom,pm8150-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vreg_l3a: ldo3 {
+ regulator-name = "vreg_l3a";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1208000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l5a: ldo5 {
+ regulator-name = "vreg_l5a";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l7a: ldo7 {
+ regulator-name = "vreg_l7a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l13a: ldo13 {
+ regulator-name = "vreg_l13a";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+ };
+
+ pmm8540-c-regulators {
+ compatible = "qcom,pm8150-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vreg_l1c: ldo1 {
+ regulator-name = "vreg_l1c";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l2c: ldo2 {
+ regulator-name = "vreg_l2c";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l3c: ldo3 {
+ regulator-name = "vreg_l3c";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l4c: ldo4 {
+ regulator-name = "vreg_l4c";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1208000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l6c: ldo6 {
+ regulator-name = "vreg_l6c";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l7c: ldo7 {
+ regulator-name = "vreg_l7c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l10c: ldo10 {
+ regulator-name = "vreg_l10c";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l17c: ldo17 {
+ regulator-name = "vreg_l17c";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+ };
+
+ pmm8540-g-regulators {
+ compatible = "qcom,pm8150-rpmh-regulators";
+ qcom,pmic-id = "g";
+
+ vreg_l3g: ldo3 {
+ regulator-name = "vreg_l3g";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l7g: ldo7 {
+ regulator-name = "vreg_l7g";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l8g: ldo8 {
+ regulator-name = "vreg_l8g";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+ };
+};
+
+&qup2 {
+ status = "okay";
+};
+
+&qup2_uart17 {
+ compatible = "qcom,geni-debug-uart";
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/sa8540p/adsp.mbn";
+ status = "okay";
+};
+
+&remoteproc_nsp0 {
+ firmware-name = "qcom/sa8540p/cdsp.mbn";
+ status = "okay";
+};
+
+&remoteproc_nsp1 {
+ firmware-name = "qcom/sa8540p/cdsp1.mbn";
+ status = "okay";
+};
+
+&spmi_bus {
+ pm8450a: pmic@0 {
+ compatible = "qcom,pm8150", "qcom,spmi-pmic";
+ reg = <0x0 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8450a_gpios: gpio@...0 {
+ compatible = "qcom,pm8150-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pm8450c: pmic@4 {
+ compatible = "qcom,pm8150", "qcom,spmi-pmic";
+ reg = <0x4 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8450c_gpios: gpio@...0 {
+ compatible = "qcom,pm8150-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pm8450e: pmic@8 {
+ compatible = "qcom,pm8150", "qcom,spmi-pmic";
+ reg = <0x8 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8450e_gpios: gpio@...0 {
+ compatible = "qcom,pm8150-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pm8450g: pmic@c {
+ compatible = "qcom,pm8150", "qcom,spmi-pmic";
+ reg = <0xc SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8450g_gpios: gpio@...0 {
+ compatible = "qcom,pm8150-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l17c>;
+ vcc-max-microamp = <800000>;
+ vccq-supply = <&vreg_l6c>;
+ vccq-max-microamp = <900000>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l8g>;
+ vdda-pll-supply = <&vreg_l3g>;
+
+ status = "okay";
+};
+
+&ufs_card_hc {
+ reset-gpios = <&tlmm 229 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l10c>;
+ vcc-max-microamp = <800000>;
+ vccq-supply = <&vreg_l3c>;
+ vccq-max-microamp = <900000>;
+
+ status = "okay";
+};
+
+&ufs_card_phy {
+ vdda-phy-supply = <&vreg_l8g>;
+ vdda-pll-supply = <&vreg_l3g>;
+
+ status = "okay";
+};
+
+&usb_0 {
+ status = "okay";
+};
+
+&usb_0_dwc3 {
+ /* TODO: Define USB-C connector properly */
+ dr_mode = "peripheral";
+};
+
+&usb_0_hsphy {
+ vdda-pll-supply = <&vreg_l5a>;
+ vdda18-supply = <&vreg_l7a>;
+ vdda33-supply = <&vreg_l13a>;
+
+ status = "okay";
+};
+
+&usb_0_qmpphy {
+ vdda-phy-supply = <&vreg_l3a>;
+ vdda-pll-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ /* TODO: Define USB-C connector properly */
+ dr_mode = "host";
+};
+
+&usb_1_hsphy {
+ vdda-pll-supply = <&vreg_l1c>;
+ vdda18-supply = <&vreg_l7c>;
+ vdda33-supply = <&vreg_l2c>;
+
+ status = "okay";
+};
+
+&usb_1_qmpphy {
+ vdda-phy-supply = <&vreg_l4c>;
+ vdda-pll-supply = <&vreg_l1c>;
+
+ status = "okay";
+};
+
+&usb_2_hsphy0 {
+ vdda-pll-supply = <&vreg_l5a>;
+ vdda18-supply = <&vreg_l7g>;
+ vdda33-supply = <&vreg_l13a>;
+
+ status = "okay";
+};
+
+&usb_2_hsphy1 {
+ vdda-pll-supply = <&vreg_l5a>;
+ vdda18-supply = <&vreg_l7g>;
+ vdda33-supply = <&vreg_l13a>;
+
+ status = "okay";
+};
+
+&usb_2_hsphy2 {
+ vdda-pll-supply = <&vreg_l5a>;
+ vdda18-supply = <&vreg_l7g>;
+ vdda33-supply = <&vreg_l13a>;
+
+ status = "okay";
+};
+
+&usb_2_hsphy3 {
+ vdda-pll-supply = <&vreg_l5a>;
+ vdda18-supply = <&vreg_l7g>;
+ vdda33-supply = <&vreg_l13a>;
+
+ status = "okay";
+};
+
+&usb_2_qmpphy0 {
+ vdda-phy-supply = <&vreg_l3a>;
+ vdda-pll-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
+
+&usb_2_qmpphy1 {
+ vdda-phy-supply = <&vreg_l3a>;
+ vdda-pll-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
+
+&xo_board_clk {
+ clock-frequency = <38400000>;
+};
+
+/* PINCTRL */
+&pm8450c_gpios {
+ usb2_en_state: usb2-en-state {
+ pins = "gpio9";
+ function = "normal";
+ output-high;
+ power-source = <0>;
+ };
+};
+
+&pm8450e_gpios {
+ usb3_en_state: usb3-en-state {
+ pins = "gpio5";
+ function = "normal";
+ output-high;
+ power-source = <0>;
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/sa8540p.dtsi b/arch/arm64/boot/dts/qcom/sa8540p.dtsi
new file mode 100644
index 000000000000..8ea2886fbab2
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sa8540p.dtsi
@@ -0,0 +1,133 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+#include "sc8280xp.dtsi"
+
+/delete-node/ &cpu0_opp_table;
+/delete-node/ &cpu4_opp_table;
+
+/ {
+ cpu0_opp_table: cpu0-opp-table {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-403200000 {
+ opp-hz = /bits/ 64 <403200000>;
+ };
+ opp-499200000 {
+ opp-hz = /bits/ 64 <499200000>;
+ };
+ opp-595200000 {
+ opp-hz = /bits/ 64 <595200000>;
+ };
+ opp-710400000 {
+ opp-hz = /bits/ 64 <710400000>;
+ };
+ opp-806400000 {
+ opp-hz = /bits/ 64 <806400000>;
+ };
+ opp-902400000 {
+ opp-hz = /bits/ 64 <902400000>;
+ };
+ opp-1017600000 {
+ opp-hz = /bits/ 64 <1017600000>;
+ };
+ opp-1113600000 {
+ opp-hz = /bits/ 64 <1113600000>;
+ };
+ opp-1209600000 {
+ opp-hz = /bits/ 64 <1209600000>;
+ };
+ opp-1324800000 {
+ opp-hz = /bits/ 64 <1324800000>;
+ };
+ opp-1440000000 {
+ opp-hz = /bits/ 64 <1440000000>;
+ };
+ opp-1555200000 {
+ opp-hz = /bits/ 64 <1555200000>;
+ };
+ opp-1670400000 {
+ opp-hz = /bits/ 64 <1670400000>;
+ };
+ opp-1785600000 {
+ opp-hz = /bits/ 64 <1785600000>;
+ };
+ opp-1881600000 {
+ opp-hz = /bits/ 64 <1881600000>;
+ };
+ opp-2016000000 {
+ opp-hz = /bits/ 64 <2016000000>;
+ };
+ opp-2131200000 {
+ opp-hz = /bits/ 64 <2131200000>;
+ };
+ opp-2246400000 {
+ opp-hz = /bits/ 64 <2246400000>;
+ };
+ };
+
+ cpu4_opp_table: cpu4-opp-table {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-825600000 {
+ opp-hz = /bits/ 64 <825600000>;
+ };
+ opp-940800000 {
+ opp-hz = /bits/ 64 <940800000>;
+ };
+ opp-1056000000 {
+ opp-hz = /bits/ 64 <1056000000>;
+ };
+ opp-1171200000 {
+ opp-hz = /bits/ 64 <1171200000>;
+ };
+ opp-1286400000 {
+ opp-hz = /bits/ 64 <1286400000>;
+ };
+ opp-1401600000 {
+ opp-hz = /bits/ 64 <1401600000>;
+ };
+ opp-1516800000 {
+ opp-hz = /bits/ 64 <1516800000>;
+ };
+ opp-1632000000 {
+ opp-hz = /bits/ 64 <1632000000>;
+ };
+ opp-1747200000 {
+ opp-hz = /bits/ 64 <1747200000>;
+ };
+ opp-1862400000 {
+ opp-hz = /bits/ 64 <1862400000>;
+ };
+ opp-1977600000 {
+ opp-hz = /bits/ 64 <1977600000>;
+ };
+ opp-2073600000 {
+ opp-hz = /bits/ 64 <2073600000>;
+ };
+ opp-2169600000 {
+ opp-hz = /bits/ 64 <2169600000>;
+ };
+ opp-2284800000 {
+ opp-hz = /bits/ 64 <2284800000>;
+ };
+ opp-2380800000 {
+ opp-hz = /bits/ 64 <2380800000>;
+ };
+ opp-2496000000 {
+ opp-hz = /bits/ 64 <2496000000>;
+ };
+ opp-2592000000 {
+ opp-hz = /bits/ 64 <2592000000>;
+ };
+ };
+};
+
+&rpmhpd {
+ compatible = "qcom,sa8540p-rpmhpd";
+};
--
2.35.1
Powered by blists - more mailing lists