| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20220629091716.68771-3-srinivas.kandagatla@linaro.org>
Date: Wed, 29 Jun 2022 10:17:16 +0100
From: Srinivas Kandagatla <srinivas.kandagatla@...aro.org>
To: bjorn.andersson@...aro.org, linus.walleij@...aro.org
Cc: robh+dt@...nel.org, krzysztof.kozlowski+dt@...aro.org,
linux-arm-msm@...r.kernel.org, linux-gpio@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
Srinivas Kandagatla <srinivas.kandagatla@...aro.org>
Subject: [PATCH 2/2] pinctrl: qcom: Add sm8450 lpass lpi pinctrl driver
Add pinctrl driver to support pin configuration for LPASS
(Low Power Audio SubSystem) LPI (Low Power Island) pinctrl
on SM8450.
This IP is an additional pin control block for Audio Pins on top the
existing SoC Top level pin-controller.
Hardware setup looks like:
TLMM GPIO[165 - 187] --> LPASS LPI GPIO [0 - 22]
This pin controller has some similarities compared to Top level
msm SoC Pin controller like 'each pin belongs to a single group'
and so on. However this one is intended to control only audio
pins in particular, which can not be configured/touched by the
Top level SoC pin controller except setting them as gpios.
Apart from this, slew rate is also available in this block for
certain pins which are connected to SLIMbus or SoundWire Bus.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@...aro.org>
---
drivers/pinctrl/qcom/Kconfig | 9 +
drivers/pinctrl/qcom/Makefile | 1 +
.../pinctrl/qcom/pinctrl-sm8450-lpass-lpi.c | 240 ++++++++++++++++++
3 files changed, 250 insertions(+)
create mode 100644 drivers/pinctrl/qcom/pinctrl-sm8450-lpass-lpi.c
diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig
index 3daeb9772391..c4d6089bf38c 100644
--- a/drivers/pinctrl/qcom/Kconfig
+++ b/drivers/pinctrl/qcom/Kconfig
@@ -373,6 +373,15 @@ config PINCTRL_SM8450
Qualcomm Technologies Inc TLMM block found on the Qualcomm
Technologies Inc SM8450 platform.
+config PINCTRL_SM8450_LPASS_LPI
+ tristate "Qualcomm Technologies Inc SM8450 LPASS LPI pin controller driver"
+ depends on GPIOLIB
+ depends on PINCTRL_LPASS_LPI
+ help
+ This is the pinctrl, pinmux, pinconf and gpiolib driver for the
+ Qualcomm Technologies Inc LPASS (Low Power Audio SubSystem) LPI
+ (Low Power Island) found on the Qualcomm Technologies Inc SM8450 platform.
+
config PINCTRL_LPASS_LPI
tristate "Qualcomm Technologies Inc LPASS LPI pin controller driver"
select PINMUX
diff --git a/drivers/pinctrl/qcom/Makefile b/drivers/pinctrl/qcom/Makefile
index 4f0ee7597f81..e3de2cd6e1d8 100644
--- a/drivers/pinctrl/qcom/Makefile
+++ b/drivers/pinctrl/qcom/Makefile
@@ -43,4 +43,5 @@ obj-$(CONFIG_PINCTRL_SM8250) += pinctrl-sm8250.o
obj-$(CONFIG_PINCTRL_SM8250_LPASS_LPI) += pinctrl-sm8250-lpass-lpi.o
obj-$(CONFIG_PINCTRL_SM8350) += pinctrl-sm8350.o
obj-$(CONFIG_PINCTRL_SM8450) += pinctrl-sm8450.o
+obj-$(CONFIG_PINCTRL_SM8450_LPASS_LPI) += pinctrl-sm8450-lpass-lpi.o
obj-$(CONFIG_PINCTRL_LPASS_LPI) += pinctrl-lpass-lpi.o
diff --git a/drivers/pinctrl/qcom/pinctrl-sm8450-lpass-lpi.c b/drivers/pinctrl/qcom/pinctrl-sm8450-lpass-lpi.c
new file mode 100644
index 000000000000..c3c8c34148f1
--- /dev/null
+++ b/drivers/pinctrl/qcom/pinctrl-sm8450-lpass-lpi.c
@@ -0,0 +1,240 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2022 Linaro Ltd.
+ */
+
+#include <linux/gpio/driver.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-lpass-lpi.h"
+
+enum lpass_lpi_functions {
+ LPI_MUX_dmic1_clk,
+ LPI_MUX_dmic1_data,
+ LPI_MUX_dmic2_clk,
+ LPI_MUX_dmic2_data,
+ LPI_MUX_dmic3_clk,
+ LPI_MUX_dmic3_data,
+ LPI_MUX_dmic4_clk,
+ LPI_MUX_dmic4_data,
+ LPI_MUX_i2s1_clk,
+ LPI_MUX_i2s1_data,
+ LPI_MUX_i2s1_ws,
+ LPI_MUX_i2s2_clk,
+ LPI_MUX_i2s2_data,
+ LPI_MUX_i2s2_ws,
+ LPI_MUX_i2s3_clk,
+ LPI_MUX_i2s3_data,
+ LPI_MUX_i2s3_ws,
+ LPI_MUX_i2s4_clk,
+ LPI_MUX_i2s4_data,
+ LPI_MUX_i2s4_ws,
+ LPI_MUX_qua_mi2s_data,
+ LPI_MUX_qua_mi2s_sclk,
+ LPI_MUX_qua_mi2s_ws,
+ LPI_MUX_swr_rx_clk,
+ LPI_MUX_swr_rx_data,
+ LPI_MUX_swr_tx_clk,
+ LPI_MUX_swr_tx_data,
+ LPI_MUX_wsa_swr_clk,
+ LPI_MUX_wsa_swr_data,
+ LPI_MUX_wsa2_swr_clk,
+ LPI_MUX_wsa2_swr_data,
+ LPI_MUX_slimbus_clk,
+ LPI_MUX_slimbus_data,
+ LPI_MUX_ext_mclk1_a,
+ LPI_MUX_ext_mclk1_b,
+ LPI_MUX_ext_mclk1_c,
+ LPI_MUX_ext_mclk1_d,
+ LPI_MUX_ext_mclk1_e,
+ LPI_MUX_gpio,
+ LPI_MUX__,
+};
+
+static int gpio0_pins[] = { 0 };
+static int gpio1_pins[] = { 1 };
+static int gpio2_pins[] = { 2 };
+static int gpio3_pins[] = { 3 };
+static int gpio4_pins[] = { 4 };
+static int gpio5_pins[] = { 5 };
+static int gpio6_pins[] = { 6 };
+static int gpio7_pins[] = { 7 };
+static int gpio8_pins[] = { 8 };
+static int gpio9_pins[] = { 9 };
+static int gpio10_pins[] = { 10 };
+static int gpio11_pins[] = { 11 };
+static int gpio12_pins[] = { 12 };
+static int gpio13_pins[] = { 13 };
+static int gpio14_pins[] = { 14 };
+static int gpio15_pins[] = { 15 };
+static int gpio16_pins[] = { 16 };
+static int gpio17_pins[] = { 17 };
+static int gpio18_pins[] = { 18 };
+static int gpio19_pins[] = { 19 };
+static int gpio20_pins[] = { 20 };
+static int gpio21_pins[] = { 21 };
+static int gpio22_pins[] = { 22 };
+
+static const struct pinctrl_pin_desc sm8450_lpi_pins[] = {
+ PINCTRL_PIN(0, "gpio0"),
+ PINCTRL_PIN(1, "gpio1"),
+ PINCTRL_PIN(2, "gpio2"),
+ PINCTRL_PIN(3, "gpio3"),
+ PINCTRL_PIN(4, "gpio4"),
+ PINCTRL_PIN(5, "gpio5"),
+ PINCTRL_PIN(6, "gpio6"),
+ PINCTRL_PIN(7, "gpio7"),
+ PINCTRL_PIN(8, "gpio8"),
+ PINCTRL_PIN(9, "gpio9"),
+ PINCTRL_PIN(10, "gpio10"),
+ PINCTRL_PIN(11, "gpio11"),
+ PINCTRL_PIN(12, "gpio12"),
+ PINCTRL_PIN(13, "gpio13"),
+ PINCTRL_PIN(14, "gpio14"),
+ PINCTRL_PIN(15, "gpio15"),
+ PINCTRL_PIN(16, "gpio16"),
+ PINCTRL_PIN(17, "gpio17"),
+ PINCTRL_PIN(18, "gpio18"),
+ PINCTRL_PIN(19, "gpio19"),
+ PINCTRL_PIN(20, "gpio20"),
+ PINCTRL_PIN(21, "gpio21"),
+ PINCTRL_PIN(22, "gpio22"),
+};
+
+static const char * const swr_tx_clk_groups[] = { "gpio0" };
+static const char * const swr_tx_data_groups[] = { "gpio1", "gpio2", "gpio14" };
+static const char * const swr_rx_clk_groups[] = { "gpio3" };
+static const char * const swr_rx_data_groups[] = { "gpio4", "gpio5", "gpio15" };
+static const char * const dmic1_clk_groups[] = { "gpio6" };
+static const char * const dmic1_data_groups[] = { "gpio7" };
+static const char * const dmic2_clk_groups[] = { "gpio8" };
+static const char * const dmic2_data_groups[] = { "gpio9" };
+static const char * const dmic4_clk_groups[] = { "gpio17" };
+static const char * const dmic4_data_groups[] = { "gpio18" };
+static const char * const i2s2_clk_groups[] = { "gpio10" };
+static const char * const i2s2_ws_groups[] = { "gpio11" };
+static const char * const dmic3_clk_groups[] = { "gpio12" };
+static const char * const dmic3_data_groups[] = { "gpio13" };
+static const char * const qua_mi2s_sclk_groups[] = { "gpio0" };
+static const char * const qua_mi2s_ws_groups[] = { "gpio1" };
+static const char * const qua_mi2s_data_groups[] = { "gpio2", "gpio3", "gpio4", "gpio5" };
+static const char * const i2s1_clk_groups[] = { "gpio6" };
+static const char * const i2s1_ws_groups[] = { "gpio7" };
+static const char * const i2s1_data_groups[] = { "gpio8", "gpio9" };
+static const char * const wsa_swr_clk_groups[] = { "gpio10" };
+static const char * const wsa_swr_data_groups[] = { "gpio11" };
+static const char * const wsa2_swr_clk_groups[] = { "gpio15" };
+static const char * const wsa2_swr_data_groups[] = { "gpio16" };
+static const char * const i2s2_data_groups[] = { "gpio15", "gpio16" };
+static const char * const i2s4_ws_groups[] = { "gpio13" };
+static const char * const i2s4_clk_groups[] = { "gpio12" };
+static const char * const i2s4_data_groups[] = { "gpio17", "gpio18" };
+static const char * const slimbus_clk_groups[] = { "gpio19"};
+static const char * const i2s3_clk_groups[] = { "gpio19"};
+static const char * const i2s3_ws_groups[] = { "gpio20"};
+static const char * const i2s3_data_groups[] = { "gpio21", "gpio22"};
+static const char * const slimbus_data_groups[] = { "gpio20"};
+static const char * const ext_mclk1_c_groups[] = { "gpio5" };
+static const char * const ext_mclk1_b_groups[] = { "gpio9" };
+static const char * const ext_mclk1_a_groups[] = { "gpio13" };
+static const char * const ext_mclk1_d_groups[] = { "gpio14" };
+static const char * const ext_mclk1_e_groups[] = { "gpio22" };
+
+static const struct lpi_pingroup sm8450_groups[] = {
+ LPI_PINGROUP(0, 0, swr_tx_clk, qua_mi2s_sclk, _, _),
+ LPI_PINGROUP(1, 2, swr_tx_data, qua_mi2s_ws, _, _),
+ LPI_PINGROUP(2, 4, swr_tx_data, qua_mi2s_data, _, _),
+ LPI_PINGROUP(3, 8, swr_rx_clk, qua_mi2s_data, _, _),
+ LPI_PINGROUP(4, 10, swr_rx_data, qua_mi2s_data, _, _),
+ LPI_PINGROUP(5, 12, swr_rx_data, ext_mclk1_c, qua_mi2s_data, _),
+ LPI_PINGROUP(6, LPI_NO_SLEW, dmic1_clk, i2s1_clk, _, _),
+ LPI_PINGROUP(7, LPI_NO_SLEW, dmic1_data, i2s1_ws, _, _),
+ LPI_PINGROUP(8, LPI_NO_SLEW, dmic2_clk, i2s1_data, _, _),
+ LPI_PINGROUP(9, LPI_NO_SLEW, dmic2_data, i2s1_data, ext_mclk1_b, _),
+ LPI_PINGROUP(10, 16, i2s2_clk, wsa_swr_clk, _, _),
+ LPI_PINGROUP(11, 18, i2s2_ws, wsa_swr_data, _, _),
+ LPI_PINGROUP(12, LPI_NO_SLEW, dmic3_clk, i2s4_clk, _, _),
+ LPI_PINGROUP(13, LPI_NO_SLEW, dmic3_data, i2s4_ws, ext_mclk1_a, _),
+ LPI_PINGROUP(14, 6, swr_tx_data, ext_mclk1_d, _, _),
+ LPI_PINGROUP(15, 20, i2s2_data, wsa2_swr_clk, _, _),
+ LPI_PINGROUP(16, 22, i2s2_data, wsa2_swr_data, _, _),
+ LPI_PINGROUP(17, LPI_NO_SLEW, dmic4_clk, i2s4_data, _, _),
+ LPI_PINGROUP(18, LPI_NO_SLEW, dmic4_data, i2s4_data, _, _),
+ LPI_PINGROUP(19, LPI_NO_SLEW, i2s3_clk, slimbus_clk, _, _),
+ LPI_PINGROUP(20, LPI_NO_SLEW, i2s3_ws, slimbus_data, _, _),
+ LPI_PINGROUP(21, LPI_NO_SLEW, i2s3_data, _, _, _),
+ LPI_PINGROUP(22, LPI_NO_SLEW, i2s3_data, ext_mclk1_e, _, _),
+};
+
+static const struct lpi_function sm8450_functions[] = {
+ LPI_FUNCTION(dmic1_clk),
+ LPI_FUNCTION(dmic1_data),
+ LPI_FUNCTION(dmic2_clk),
+ LPI_FUNCTION(dmic2_data),
+ LPI_FUNCTION(dmic3_clk),
+ LPI_FUNCTION(dmic3_data),
+ LPI_FUNCTION(dmic4_clk),
+ LPI_FUNCTION(dmic4_data),
+ LPI_FUNCTION(i2s1_clk),
+ LPI_FUNCTION(i2s1_data),
+ LPI_FUNCTION(i2s1_ws),
+ LPI_FUNCTION(i2s2_clk),
+ LPI_FUNCTION(i2s2_data),
+ LPI_FUNCTION(i2s2_ws),
+ LPI_FUNCTION(i2s3_clk),
+ LPI_FUNCTION(i2s3_data),
+ LPI_FUNCTION(i2s3_ws),
+ LPI_FUNCTION(i2s4_clk),
+ LPI_FUNCTION(i2s4_data),
+ LPI_FUNCTION(i2s4_ws),
+ LPI_FUNCTION(qua_mi2s_data),
+ LPI_FUNCTION(qua_mi2s_sclk),
+ LPI_FUNCTION(qua_mi2s_ws),
+ LPI_FUNCTION(swr_rx_clk),
+ LPI_FUNCTION(swr_rx_data),
+ LPI_FUNCTION(swr_tx_clk),
+ LPI_FUNCTION(swr_tx_data),
+ LPI_FUNCTION(slimbus_clk),
+ LPI_FUNCTION(slimbus_data),
+ LPI_FUNCTION(wsa_swr_clk),
+ LPI_FUNCTION(wsa_swr_data),
+ LPI_FUNCTION(wsa2_swr_clk),
+ LPI_FUNCTION(wsa2_swr_data),
+ LPI_FUNCTION(ext_mclk1_a),
+ LPI_FUNCTION(ext_mclk1_b),
+ LPI_FUNCTION(ext_mclk1_c),
+ LPI_FUNCTION(ext_mclk1_d),
+ LPI_FUNCTION(ext_mclk1_e),
+};
+
+static const struct lpi_pinctrl_variant_data sm8450_lpi_data = {
+ .pins = sm8450_lpi_pins,
+ .npins = ARRAY_SIZE(sm8450_lpi_pins),
+ .groups = sm8450_groups,
+ .ngroups = ARRAY_SIZE(sm8450_groups),
+ .functions = sm8450_functions,
+ .nfunctions = ARRAY_SIZE(sm8450_functions),
+};
+
+static const struct of_device_id lpi_pinctrl_of_match[] = {
+ {
+ .compatible = "qcom,sm8450-lpass-lpi-pinctrl",
+ .data = &sm8450_lpi_data,
+ },
+ { }
+};
+MODULE_DEVICE_TABLE(of, lpi_pinctrl_of_match);
+
+static struct platform_driver lpi_pinctrl_driver = {
+ .driver = {
+ .name = "qcom-sm8450-lpass-lpi-pinctrl",
+ .of_match_table = lpi_pinctrl_of_match,
+ },
+ .probe = lpi_pinctrl_probe,
+ .remove = lpi_pinctrl_remove,
+};
+
+module_platform_driver(lpi_pinctrl_driver);
+MODULE_DESCRIPTION("QTI SM8450 LPI GPIO pin control driver");
+MODULE_LICENSE("GPL");
--
2.25.1
Powered by blists - more mailing lists