[<prev] [next>] [thread-next>] [day] [month] [year] [list]
Message-Id: <20220703170039.2058202-1-LinoSanfilippo@gmx.de>
Date: Sun, 3 Jul 2022 19:00:30 +0200
From: Lino Sanfilippo <LinoSanfilippo@....de>
To: gregkh@...uxfoundation.org, jirislaby@...nel.org
Cc: ilpo.jarvinen@...ux.intel.com, robh+dt@...nel.org,
krzysztof.kozlowski+dt@...aro.org,
andriy.shevchenko@...ux.intel.com, vz@...ia.com,
linux-arm-kernel@...ts.infradead.org, devicetree@...r.kernel.org,
linux-serial@...r.kernel.org, linux-kernel@...r.kernel.org,
lukas@...ner.de, p.rosenberger@...bus.com,
Lino Sanfilippo <l.sanfilippo@...bus.com>
Subject: [PATCH v2 0/9] Fixes and cleanup for RS485
From: Lino Sanfilippo <l.sanfilippo@...bus.com>
The following series includes cleanup and fixes around RS485 in the serial
core and uart drivers:
Patch 1: Only request the rs485 termination gpio if it is supported.
NOTE:
This patch follows the design decision that "rs485_supported" is
set by the driver at initialization and cannot be modified
afterwards. However the better approach would be to let the serial
core modify the termination GPIO support setting based on the
existence of a termination GPIO. If "rs485_supported" is not a
read-only value any more in future the logic implemented in this
patch should be adjusted accordingly.
Patch 2: Set the rs485 termination GPIO in the serial core. This is needed
since if the gpio is only accessible in sleepable context. It also
is a further step to make the RS485 handling more generic.
Patch 3: Move sanitizing of RS485 delays into an own function. This is in
preparation of patch 4.
Patch 4: Sanitize RS485 delays read from device tree.
Patch 5: Correct RS485 delays in binding documentation.
Patch 6: Remove redundant code in 8250_dwlib.
Patch 7: Fix check for RS485 support.
Patch 8: Remove redundant code in ar933x.
Patch 9: Remove redundant code in 8250-lpc18xx.
Changes in v2:
- print a warning if termination GPIO is specified in DT/ACPI but is not
supported by driver
- fixed commit message for devtree documentation (as suggested by Andy)
- fixed code comment
- added patch 7
Lino Sanfilippo (9):
serial: core: only get RS485 termination GPIO if supported
serial: core, 8250: set RS485 termination gpio in serial core
serial: core: move sanitizing of RS485 delays into own function
serial: core: sanitize RS485 delays read from device tree
dt_bindings: rs485: Correct delay values
serial: 8250_dwlib: remove redundant sanity check for RS485 flags
serial: ar933x: Fix check for RS485 support
serial: ar933x: Remove redundant assignment in rs485_config
serial: 8250: lpc18xx: Remove redundant sanity check for RS485 flags
.../devicetree/bindings/serial/rs485.yaml | 4 +-
drivers/tty/serial/8250/8250_dwlib.c | 10 +--
drivers/tty/serial/8250/8250_lpc18xx.c | 6 +-
drivers/tty/serial/8250/8250_port.c | 3 -
drivers/tty/serial/ar933x_uart.c | 18 ++---
drivers/tty/serial/serial_core.c | 70 +++++++++++++------
6 files changed, 60 insertions(+), 51 deletions(-)
base-commit: 7349660438603ed19282e75949561406531785a5
--
2.25.1
Powered by blists - more mailing lists