| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20220801185304.ozoydbmbgqe6fqdy@SoMainline.org>
Date: Mon, 1 Aug 2022 20:53:04 +0200
From: Marijn Suijten <marijn.suijten@...ainline.org>
To: Joel Selvaraj <joel.selvaraj@...look.com>
Cc: Andy Gross <agross@...nel.org>,
Bjorn Andersson <bjorn.andersson@...aro.org>,
Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
linux-arm-msm@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org,
~postmarketos/upstreaming@...ts.sr.ht, phone-devel@...r.kernel.org
Subject: Re: [PATCH v2 2/3] arm64: dts: qcom: sdm845-xiaomi-beryllium-common:
move common nodes to a common dtsi
On 2022-08-01 16:55:11, Joel Selvaraj wrote:
> Since there are two variants of Xiaomi Poco F1, move the common nodes from
> Tianma variant into a new common dtsi. The EBBG variant will also inherit
> the new common dtsi.
>
> Signed-off-by: Joel Selvaraj <joel.selvaraj@...look.com>
> ---
Any summary what changed since v1?
> .../qcom/sdm845-xiaomi-beryllium-common.dtsi | 595 ++++++++++++++++++
> .../qcom/sdm845-xiaomi-beryllium-tianma.dts | 590 +----------------
> 2 files changed, 598 insertions(+), 587 deletions(-)
> create mode 100644 arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
> new file mode 100644
> index 000000000000..83edcb1171f5
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
I haven't re-read what was discussed in v1, but doing it this way causes
git to _not_ record this as a rename but instead state that everything
has been removed from sdm845-xiaomi-beryllium-tianma.dts, and a new file
sdm845-xiaomi-beryllium-common.dtsi was introduced with inconveniently
almost identical contents (see the unnecessary size of the patch that
follows).
Instead, I'd keep the original patch with a rename from
sdm845-xiaomi-beryllium.dts to sdm845-xiaomi-beryllium-common.dtsi, and
_also_ update the existing:
dtb-$(CONFIG_ARCH_QCOM) += sdm845-xiaomi-beryllium.dtb
in Makefile to match this rename so that it keeps compiling, even if
that means we treat a .dtsi as a .dts which may (likely) not be treated
correctly by existing build rules.
If it doesn't - and this approach is probably frowned upon anyway - it
is perhaps easiest to generalize sdm845-xiaomi-beryllium.dtb (as
suggested above) _and_ introduce sdm845-xiaomi-beryllium-tianma.dtb
_and_ update Makefile in a _single_ patch, such that everyting keeps
compiling and stays consistent wrt how git treats renames. Later
patches update the compatible and add the ebbg variant.
- Marijn
> @@ -0,0 +1,595 @@
> +// SPDX-License-Identifier: GPL-2.0
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +#include <dt-bindings/sound/qcom,q6afe.h>
> +#include <dt-bindings/sound/qcom,q6asm.h>
> +#include "sdm845.dtsi"
> +#include "pm8998.dtsi"
> +#include "pmi8998.dtsi"
> +
> +/*
> + * Delete following upstream (sdm845.dtsi) reserved
> + * memory mappings which are different in this device.
> + */
> +/delete-node/ &tz_mem;
> +/delete-node/ &adsp_mem;
> +/delete-node/ &wlan_msa_mem;
> +/delete-node/ &mpss_region;
> +/delete-node/ &venus_mem;
> +/delete-node/ &cdsp_mem;
> +/delete-node/ &mba_region;
> +/delete-node/ &slpi_mem;
> +/delete-node/ &spss_mem;
> +/delete-node/ &rmtfs_mem;
> +
> +/ {
> + model = "Xiaomi Pocophone F1";
> + compatible = "xiaomi,beryllium", "qcom,sdm845";
> + chassis-type = "handset";
> +
> + /* required for bootloader to select correct board */
> + qcom,board-id = <69 0>;
> + qcom,msm-id = <321 0x20001>;
> +
> + aliases {
> + hsuart0 = &uart6;
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + autorepeat;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&vol_up_pin_a>;
> +
> + vol-up {
> + label = "Volume Up";
> + linux,code = <KEY_VOLUMEUP>;
> + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + /* Reserved memory changes from downstream */
> + reserved-memory {
> + tz_mem: memory@...00000 {
> + reg = <0 0x86200000 0 0x4900000>;
> + no-map;
> + };
> +
> + adsp_mem: memory@...00000 {
> + reg = <0 0x8c500000 0 0x1e00000>;
> + no-map;
> + };
> +
> + wlan_msa_mem: memory@...00000 {
> + reg = <0 0x8e300000 0 0x100000>;
> + no-map;
> + };
> +
> + mpss_region: memory@...00000 {
> + reg = <0 0x8e400000 0 0x7800000>;
> + no-map;
> + };
> +
> + venus_mem: memory@...00000 {
> + reg = <0 0x95c00000 0 0x500000>;
> + no-map;
> + };
> +
> + cdsp_mem: memory@...00000 {
> + reg = <0 0x96100000 0 0x800000>;
> + no-map;
> + };
> +
> + mba_region: memory@...00000 {
> + reg = <0 0x96900000 0 0x200000>;
> + no-map;
> + };
> +
> + slpi_mem: memory@...00000 {
> + reg = <0 0x96b00000 0 0x1400000>;
> + no-map;
> + };
> +
> + spss_mem: memory@...00000 {
> + reg = <0 0x97f00000 0 0x100000>;
> + no-map;
> + };
> +
> + rmtfs_mem: memory@...01000 {
> + compatible = "qcom,rmtfs-mem";
> + reg = <0 0xf6301000 0 0x200000>;
> + no-map;
> +
> + qcom,client-id = <1>;
> + qcom,vmid = <15>;
> + };
> + };
> +
> + vreg_s4a_1p8: vreg-s4a-1p8 {
> + compatible = "regulator-fixed";
> + regulator-name = "vreg_s4a_1p8";
> +
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +};
> +
> +&adsp_pas {
> + status = "okay";
> + firmware-name = "qcom/sdm845/beryllium/adsp.mbn";
> +};
> +
> +&apps_rsc {
> + pm8998-rpmh-regulators {
> + compatible = "qcom,pm8998-rpmh-regulators";
> + qcom,pmic-id = "a";
> +
> + vreg_l1a_0p875: ldo1 {
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <880000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l5a_0p8: ldo5 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l7a_1p8: ldo7 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l12a_1p8: ldo12 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l13a_2p95: ldo13 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <2960000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l14a_1p8: ldo14 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vreg_l17a_1p3: ldo17 {
> + regulator-min-microvolt = <1304000>;
> + regulator-max-microvolt = <1304000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l20a_2p95: ldo20 {
> + regulator-min-microvolt = <2960000>;
> + regulator-max-microvolt = <2968000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l21a_2p95: ldo21 {
> + regulator-min-microvolt = <2960000>;
> + regulator-max-microvolt = <2968000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l23a_3p3: ldo23 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3312000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l24a_3p075: ldo24 {
> + regulator-min-microvolt = <3088000>;
> + regulator-max-microvolt = <3088000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l25a_3p3: ldo25 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3312000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l26a_1p2: ldo26 {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-boot-on;
> + };
> + };
> +};
> +
> +&cdsp_pas {
> + status = "okay";
> + firmware-name = "qcom/sdm845/beryllium/cdsp.mbn";
> +};
> +
> +&dsi0 {
> + status = "okay";
> + vdda-supply = <&vreg_l26a_1p2>;
> +
> + display_panel: panel@0 {
> + reg = <0>;
> + vddio-supply = <&vreg_l14a_1p8>;
> + vddpos-supply = <&lab>;
> + vddneg-supply = <&ibb>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + backlight = <&pmi8998_wled>;
> + reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
> +
> + status = "disabled";
> +
> + port {
> + panel_in_0: endpoint {
> + remote-endpoint = <&dsi0_out>;
> + };
> + };
> + };
> +};
> +
> +&dsi0_out {
> + remote-endpoint = <&panel_in_0>;
> + data-lanes = <0 1 2 3>;
> +};
> +
> +&dsi0_phy {
> + status = "okay";
> + vdds-supply = <&vreg_l1a_0p875>;
> +};
> +
> +&gcc {
> + protected-clocks = <GCC_QSPI_CORE_CLK>,
> + <GCC_QSPI_CORE_CLK_SRC>,
> + <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
> + <GCC_LPASS_Q6_AXI_CLK>,
> + <GCC_LPASS_SWAY_CLK>;
> +};
> +
> +&gmu {
> + status = "okay";
> +};
> +
> +&gpu {
> + status = "okay";
> +
> + zap-shader {
> + memory-region = <&gpu_mem>;
> + firmware-name = "qcom/sdm845/beryllium/a630_zap.mbn";
> + };
> +};
> +
> +&ibb {
> + regulator-min-microvolt = <4600000>;
> + regulator-max-microvolt = <6000000>;
> + regulator-over-current-protection;
> + regulator-pull-down;
> + regulator-soft-start;
> + qcom,discharge-resistor-kohms = <300>;
> +};
> +
> +&lab {
> + regulator-min-microvolt = <4600000>;
> + regulator-max-microvolt = <6000000>;
> + regulator-over-current-protection;
> + regulator-pull-down;
> + regulator-soft-start;
> +};
> +
> +&mdss {
> + status = "okay";
> +};
> +
> +&mss_pil {
> + status = "okay";
> + firmware-name = "qcom/sdm845/beryllium/mba.mbn", "qcom/sdm845/beryllium/modem.mbn";
> +};
> +
> +&ipa {
> + status = "okay";
> + memory-region = <&ipa_fw_mem>;
> + firmware-name = "qcom/sdm845/beryllium/ipa_fws.mbn";
> +};
> +
> +&pm8998_gpio {
> + vol_up_pin_a: vol-up-active {
> + pins = "gpio6";
> + function = "normal";
> + input-enable;
> + bias-pull-up;
> + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
> + };
> +};
> +
> +&pmi8998_wled {
> + status = "okay";
> + qcom,current-boost-limit = <970>;
> + qcom,ovp-millivolt = <29600>;
> + qcom,current-limit-microamp = <20000>;
> + qcom,num-strings = <2>;
> + qcom,switching-freq = <600>;
> + qcom,external-pfet;
> + qcom,cabc;
> +};
> +
> +&pm8998_pon {
> + resin {
> + compatible = "qcom,pm8941-resin";
> + interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
> + debounce = <15625>;
> + bias-pull-up;
> + linux,code = <KEY_VOLUMEDOWN>;
> + };
> +};
> +
> +/* QUAT I2S Uses 1 I2S SD Line for audio on TAS2559/60 amplifiers */
> +&q6afedai {
> + qi2s@22 {
> + reg = <22>;
> + qcom,sd-lines = <0>;
> + };
> +};
> +
> +&q6asmdai {
> + dai@0 {
> + reg = <0>;
> + };
> +
> + dai@1 {
> + reg = <1>;
> + };
> +
> + dai@2 {
> + reg = <2>;
> + };
> +};
> +
> +&qupv3_id_0 {
> + status = "okay";
> +};
> +
> +&sdhc_2 {
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
> +
> + vmmc-supply = <&vreg_l21a_2p95>;
> + vqmmc-supply = <&vreg_l13a_2p95>;
> +
> + bus-width = <4>;
> + cd-gpios = <&tlmm 126 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&sound {
> + compatible = "qcom,db845c-sndcard";
> + pinctrl-0 = <&quat_mi2s_active
> + &quat_mi2s_sd0_active>;
> + pinctrl-names = "default";
> + model = "Xiaomi Poco F1";
> + audio-routing =
> + "RX_BIAS", "MCLK",
> + "AMIC1", "MIC BIAS1",
> + "AMIC2", "MIC BIAS2",
> + "AMIC3", "MIC BIAS3";
> +
> + mm1-dai-link {
> + link-name = "MultiMedia1";
> + cpu {
> + sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
> + };
> + };
> +
> + mm2-dai-link {
> + link-name = "MultiMedia2";
> + cpu {
> + sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>;
> + };
> + };
> +
> + mm3-dai-link {
> + link-name = "MultiMedia3";
> + cpu {
> + sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>;
> + };
> + };
> +
> + slim-dai-link {
> + link-name = "SLIM Playback";
> + cpu {
> + sound-dai = <&q6afedai SLIMBUS_0_RX>;
> + };
> +
> + platform {
> + sound-dai = <&q6routing>;
> + };
> +
> + codec {
> + sound-dai = <&wcd9340 0>;
> + };
> + };
> +
> + slimcap-dai-link {
> + link-name = "SLIM Capture";
> + cpu {
> + sound-dai = <&q6afedai SLIMBUS_0_TX>;
> + };
> +
> + platform {
> + sound-dai = <&q6routing>;
> + };
> +
> + codec {
> + sound-dai = <&wcd9340 1>;
> + };
> + };
> +};
> +
> +&tlmm {
> + gpio-reserved-ranges = <0 4>, <81 4>;
> +
> + sdc2_default_state: sdc2-default {
> + clk {
> + pins = "sdc2_clk";
> + bias-disable;
> + drive-strength = <16>;
> + };
> +
> + cmd {
> + pins = "sdc2_cmd";
> + bias-pull-up;
> + drive-strength = <10>;
> + };
> +
> + data {
> + pins = "sdc2_data";
> + bias-pull-up;
> + drive-strength = <10>;
> + };
> + };
> +
> + sdc2_card_det_n: sd-card-det-n {
> + pins = "gpio126";
> + function = "gpio";
> + bias-pull-up;
> + };
> +
> + wcd_intr_default: wcd_intr_default {
> + pins = <54>;
> + function = "gpio";
> +
> + input-enable;
> + bias-pull-down;
> + drive-strength = <2>;
> + };
> +};
> +
> +&uart6 {
> + status = "okay";
> +
> + bluetooth {
> + compatible = "qcom,wcn3990-bt";
> +
> + vddio-supply = <&vreg_s4a_1p8>;
> + vddxo-supply = <&vreg_l7a_1p8>;
> + vddrf-supply = <&vreg_l17a_1p3>;
> + vddch0-supply = <&vreg_l25a_3p3>;
> + max-speed = <3200000>;
> + };
> +};
> +
> +&ufs_mem_hc {
> + status = "okay";
> +
> + reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
> +
> + vcc-supply = <&vreg_l20a_2p95>;
> + vcc-max-microamp = <800000>;
> +};
> +
> +&ufs_mem_phy {
> + status = "okay";
> +
> + vdda-phy-supply = <&vreg_l1a_0p875>;
> + vdda-pll-supply = <&vreg_l26a_1p2>;
> +};
> +
> +&usb_1 {
> + status = "okay";
> +};
> +
> +&usb_1_dwc3 {
> + dr_mode = "peripheral";
> +};
> +
> +&usb_1_hsphy {
> + status = "okay";
> +
> + vdd-supply = <&vreg_l1a_0p875>;
> + vdda-pll-supply = <&vreg_l12a_1p8>;
> + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
> +
> + qcom,imp-res-offset-value = <8>;
> + qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
> + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
> + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
> +};
> +
> +&usb_1_qmpphy {
> + status = "okay";
> +
> + vdda-phy-supply = <&vreg_l26a_1p2>;
> + vdda-pll-supply = <&vreg_l1a_0p875>;
> +};
> +
> +&venus {
> + status = "okay";
> + firmware-name = "qcom/sdm845/beryllium/venus.mbn";
> +};
> +
> +&wcd9340{
> + pinctrl-0 = <&wcd_intr_default>;
> + pinctrl-names = "default";
> + clock-names = "extclk";
> + clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
> + reset-gpios = <&tlmm 64 0>;
> + vdd-buck-supply = <&vreg_s4a_1p8>;
> + vdd-buck-sido-supply = <&vreg_s4a_1p8>;
> + vdd-tx-supply = <&vreg_s4a_1p8>;
> + vdd-rx-supply = <&vreg_s4a_1p8>;
> + vdd-io-supply = <&vreg_s4a_1p8>;
> + qcom,micbias1-microvolt = <2700000>;
> + qcom,micbias2-microvolt = <1800000>;
> + qcom,micbias3-microvolt = <2700000>;
> + qcom,micbias4-microvolt = <2700000>;
> +};
> +
> +&wifi {
> + status = "okay";
> +
> + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
> + vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
> + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
> + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
> + vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
> +};
> +
> +/* PINCTRL - additions to nodes defined in sdm845.dtsi */
> +
> +&qup_uart6_default {
> + pinmux {
> + pins = "gpio45", "gpio46", "gpio47", "gpio48";
> + function = "qup6";
> + };
> +
> + cts {
> + pins = "gpio45";
> + bias-disable;
> + };
> +
> + rts-tx {
> + pins = "gpio46", "gpio47";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + rx {
> + pins = "gpio48";
> + bias-pull-up;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-tianma.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-tianma.dts
> index d88dc07205f7..fcbef5ad2909 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-tianma.dts
> +++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-tianma.dts
> @@ -2,593 +2,9 @@
>
> /dts-v1/;
>
> -#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> -#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> -#include <dt-bindings/sound/qcom,q6afe.h>
> -#include <dt-bindings/sound/qcom,q6asm.h>
> -#include "sdm845.dtsi"
> -#include "pm8998.dtsi"
> -#include "pmi8998.dtsi"
> +#include "sdm845-xiaomi-beryllium-common.dtsi"
>
> -/*
> - * Delete following upstream (sdm845.dtsi) reserved
> - * memory mappings which are different in this device.
> - */
> -/delete-node/ &tz_mem;
> -/delete-node/ &adsp_mem;
> -/delete-node/ &wlan_msa_mem;
> -/delete-node/ &mpss_region;
> -/delete-node/ &venus_mem;
> -/delete-node/ &cdsp_mem;
> -/delete-node/ &mba_region;
> -/delete-node/ &slpi_mem;
> -/delete-node/ &spss_mem;
> -/delete-node/ &rmtfs_mem;
> -
> -/ {
> - model = "Xiaomi Pocophone F1";
> - compatible = "xiaomi,beryllium", "qcom,sdm845";
> - chassis-type = "handset";
> -
> - /* required for bootloader to select correct board */
> - qcom,board-id = <69 0>;
> - qcom,msm-id = <321 0x20001>;
> -
> - aliases {
> - hsuart0 = &uart6;
> - };
> -
> - gpio-keys {
> - compatible = "gpio-keys";
> - autorepeat;
> -
> - pinctrl-names = "default";
> - pinctrl-0 = <&vol_up_pin_a>;
> -
> - vol-up {
> - label = "Volume Up";
> - linux,code = <KEY_VOLUMEUP>;
> - gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
> - };
> - };
> -
> - /* Reserved memory changes from downstream */
> - reserved-memory {
> - tz_mem: memory@...00000 {
> - reg = <0 0x86200000 0 0x4900000>;
> - no-map;
> - };
> -
> - adsp_mem: memory@...00000 {
> - reg = <0 0x8c500000 0 0x1e00000>;
> - no-map;
> - };
> -
> - wlan_msa_mem: memory@...00000 {
> - reg = <0 0x8e300000 0 0x100000>;
> - no-map;
> - };
> -
> - mpss_region: memory@...00000 {
> - reg = <0 0x8e400000 0 0x7800000>;
> - no-map;
> - };
> -
> - venus_mem: memory@...00000 {
> - reg = <0 0x95c00000 0 0x500000>;
> - no-map;
> - };
> -
> - cdsp_mem: memory@...00000 {
> - reg = <0 0x96100000 0 0x800000>;
> - no-map;
> - };
> -
> - mba_region: memory@...00000 {
> - reg = <0 0x96900000 0 0x200000>;
> - no-map;
> - };
> -
> - slpi_mem: memory@...00000 {
> - reg = <0 0x96b00000 0 0x1400000>;
> - no-map;
> - };
> -
> - spss_mem: memory@...00000 {
> - reg = <0 0x97f00000 0 0x100000>;
> - no-map;
> - };
> -
> - rmtfs_mem: memory@...01000 {
> - compatible = "qcom,rmtfs-mem";
> - reg = <0 0xf6301000 0 0x200000>;
> - no-map;
> -
> - qcom,client-id = <1>;
> - qcom,vmid = <15>;
> - };
> - };
> -
> - vreg_s4a_1p8: vreg-s4a-1p8 {
> - compatible = "regulator-fixed";
> - regulator-name = "vreg_s4a_1p8";
> -
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-always-on;
> - };
> -};
> -
> -&adsp_pas {
> - status = "okay";
> - firmware-name = "qcom/sdm845/beryllium/adsp.mbn";
> -};
> -
> -&apps_rsc {
> - pm8998-rpmh-regulators {
> - compatible = "qcom,pm8998-rpmh-regulators";
> - qcom,pmic-id = "a";
> -
> - vreg_l1a_0p875: ldo1 {
> - regulator-min-microvolt = <880000>;
> - regulator-max-microvolt = <880000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> - };
> -
> - vreg_l5a_0p8: ldo5 {
> - regulator-min-microvolt = <800000>;
> - regulator-max-microvolt = <800000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> - };
> -
> - vreg_l7a_1p8: ldo7 {
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> - };
> -
> - vreg_l12a_1p8: ldo12 {
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> - };
> -
> - vreg_l13a_2p95: ldo13 {
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <2960000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> - };
> -
> - vreg_l14a_1p8: ldo14 {
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - vreg_l17a_1p3: ldo17 {
> - regulator-min-microvolt = <1304000>;
> - regulator-max-microvolt = <1304000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> - };
> -
> - vreg_l20a_2p95: ldo20 {
> - regulator-min-microvolt = <2960000>;
> - regulator-max-microvolt = <2968000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> - };
> -
> - vreg_l21a_2p95: ldo21 {
> - regulator-min-microvolt = <2960000>;
> - regulator-max-microvolt = <2968000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> - };
> -
> - vreg_l23a_3p3: ldo23 {
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3312000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> - };
> -
> - vreg_l24a_3p075: ldo24 {
> - regulator-min-microvolt = <3088000>;
> - regulator-max-microvolt = <3088000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> - };
> -
> - vreg_l25a_3p3: ldo25 {
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3312000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> - };
> -
> - vreg_l26a_1p2: ldo26 {
> - regulator-min-microvolt = <1200000>;
> - regulator-max-microvolt = <1200000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> - regulator-boot-on;
> - };
> - };
> -};
> -
> -&cdsp_pas {
> +&display_panel {
> + compatible = "tianma,fhd-video";
> status = "okay";
> - firmware-name = "qcom/sdm845/beryllium/cdsp.mbn";
> -};
> -
> -&dsi0 {
> - status = "okay";
> - vdda-supply = <&vreg_l26a_1p2>;
> -
> - panel@0 {
> - compatible = "tianma,fhd-video";
> - reg = <0>;
> - vddio-supply = <&vreg_l14a_1p8>;
> - vddpos-supply = <&lab>;
> - vddneg-supply = <&ibb>;
> -
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - backlight = <&pmi8998_wled>;
> - reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
> -
> - port {
> - tianma_nt36672a_in_0: endpoint {
> - remote-endpoint = <&dsi0_out>;
> - };
> - };
> - };
> -};
> -
> -&dsi0_out {
> - remote-endpoint = <&tianma_nt36672a_in_0>;
> - data-lanes = <0 1 2 3>;
> -};
> -
> -&dsi0_phy {
> - status = "okay";
> - vdds-supply = <&vreg_l1a_0p875>;
> -};
> -
> -&gcc {
> - protected-clocks = <GCC_QSPI_CORE_CLK>,
> - <GCC_QSPI_CORE_CLK_SRC>,
> - <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
> - <GCC_LPASS_Q6_AXI_CLK>,
> - <GCC_LPASS_SWAY_CLK>;
> -};
> -
> -&gmu {
> - status = "okay";
> -};
> -
> -&gpu {
> - status = "okay";
> -
> - zap-shader {
> - memory-region = <&gpu_mem>;
> - firmware-name = "qcom/sdm845/beryllium/a630_zap.mbn";
> - };
> -};
> -
> -&ibb {
> - regulator-min-microvolt = <4600000>;
> - regulator-max-microvolt = <6000000>;
> - regulator-over-current-protection;
> - regulator-pull-down;
> - regulator-soft-start;
> - qcom,discharge-resistor-kohms = <300>;
> -};
> -
> -&lab {
> - regulator-min-microvolt = <4600000>;
> - regulator-max-microvolt = <6000000>;
> - regulator-over-current-protection;
> - regulator-pull-down;
> - regulator-soft-start;
> -};
> -
> -&mdss {
> - status = "okay";
> -};
> -
> -&mss_pil {
> - status = "okay";
> - firmware-name = "qcom/sdm845/beryllium/mba.mbn", "qcom/sdm845/beryllium/modem.mbn";
> -};
> -
> -&ipa {
> - status = "okay";
> - memory-region = <&ipa_fw_mem>;
> - firmware-name = "qcom/sdm845/beryllium/ipa_fws.mbn";
> -};
> -
> -&pm8998_gpio {
> - vol_up_pin_a: vol-up-active {
> - pins = "gpio6";
> - function = "normal";
> - input-enable;
> - bias-pull-up;
> - qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
> - };
> -};
> -
> -&pmi8998_wled {
> - status = "okay";
> - qcom,current-boost-limit = <970>;
> - qcom,ovp-millivolt = <29600>;
> - qcom,current-limit-microamp = <20000>;
> - qcom,num-strings = <2>;
> - qcom,switching-freq = <600>;
> - qcom,external-pfet;
> - qcom,cabc;
> -};
> -
> -&pm8998_pon {
> - resin {
> - compatible = "qcom,pm8941-resin";
> - interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
> - debounce = <15625>;
> - bias-pull-up;
> - linux,code = <KEY_VOLUMEDOWN>;
> - };
> -};
> -
> -/* QUAT I2S Uses 1 I2S SD Line for audio on TAS2559/60 amplifiers */
> -&q6afedai {
> - qi2s@22 {
> - reg = <22>;
> - qcom,sd-lines = <0>;
> - };
> -};
> -
> -&q6asmdai {
> - dai@0 {
> - reg = <0>;
> - };
> -
> - dai@1 {
> - reg = <1>;
> - };
> -
> - dai@2 {
> - reg = <2>;
> - };
> -};
> -
> -&qupv3_id_0 {
> - status = "okay";
> -};
> -
> -&sdhc_2 {
> - status = "okay";
> -
> - pinctrl-names = "default";
> - pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
> -
> - vmmc-supply = <&vreg_l21a_2p95>;
> - vqmmc-supply = <&vreg_l13a_2p95>;
> -
> - bus-width = <4>;
> - cd-gpios = <&tlmm 126 GPIO_ACTIVE_HIGH>;
> -};
> -
> -&sound {
> - compatible = "qcom,db845c-sndcard";
> - pinctrl-0 = <&quat_mi2s_active
> - &quat_mi2s_sd0_active>;
> - pinctrl-names = "default";
> - model = "Xiaomi Poco F1";
> - audio-routing =
> - "RX_BIAS", "MCLK",
> - "AMIC1", "MIC BIAS1",
> - "AMIC2", "MIC BIAS2",
> - "AMIC3", "MIC BIAS3";
> -
> - mm1-dai-link {
> - link-name = "MultiMedia1";
> - cpu {
> - sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
> - };
> - };
> -
> - mm2-dai-link {
> - link-name = "MultiMedia2";
> - cpu {
> - sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>;
> - };
> - };
> -
> - mm3-dai-link {
> - link-name = "MultiMedia3";
> - cpu {
> - sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>;
> - };
> - };
> -
> - slim-dai-link {
> - link-name = "SLIM Playback";
> - cpu {
> - sound-dai = <&q6afedai SLIMBUS_0_RX>;
> - };
> -
> - platform {
> - sound-dai = <&q6routing>;
> - };
> -
> - codec {
> - sound-dai = <&wcd9340 0>;
> - };
> - };
> -
> - slimcap-dai-link {
> - link-name = "SLIM Capture";
> - cpu {
> - sound-dai = <&q6afedai SLIMBUS_0_TX>;
> - };
> -
> - platform {
> - sound-dai = <&q6routing>;
> - };
> -
> - codec {
> - sound-dai = <&wcd9340 1>;
> - };
> - };
> -};
> -
> -&tlmm {
> - gpio-reserved-ranges = <0 4>, <81 4>;
> -
> - sdc2_default_state: sdc2-default {
> - clk {
> - pins = "sdc2_clk";
> - bias-disable;
> - drive-strength = <16>;
> - };
> -
> - cmd {
> - pins = "sdc2_cmd";
> - bias-pull-up;
> - drive-strength = <10>;
> - };
> -
> - data {
> - pins = "sdc2_data";
> - bias-pull-up;
> - drive-strength = <10>;
> - };
> - };
> -
> - sdc2_card_det_n: sd-card-det-n {
> - pins = "gpio126";
> - function = "gpio";
> - bias-pull-up;
> - };
> -
> - wcd_intr_default: wcd_intr_default {
> - pins = <54>;
> - function = "gpio";
> -
> - input-enable;
> - bias-pull-down;
> - drive-strength = <2>;
> - };
> -};
> -
> -&uart6 {
> - status = "okay";
> -
> - bluetooth {
> - compatible = "qcom,wcn3990-bt";
> -
> - vddio-supply = <&vreg_s4a_1p8>;
> - vddxo-supply = <&vreg_l7a_1p8>;
> - vddrf-supply = <&vreg_l17a_1p3>;
> - vddch0-supply = <&vreg_l25a_3p3>;
> - max-speed = <3200000>;
> - };
> -};
> -
> -&ufs_mem_hc {
> - status = "okay";
> -
> - reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
> -
> - vcc-supply = <&vreg_l20a_2p95>;
> - vcc-max-microamp = <800000>;
> -};
> -
> -&ufs_mem_phy {
> - status = "okay";
> -
> - vdda-phy-supply = <&vreg_l1a_0p875>;
> - vdda-pll-supply = <&vreg_l26a_1p2>;
> -};
> -
> -&usb_1 {
> - status = "okay";
> -};
> -
> -&usb_1_dwc3 {
> - dr_mode = "peripheral";
> -};
> -
> -&usb_1_hsphy {
> - status = "okay";
> -
> - vdd-supply = <&vreg_l1a_0p875>;
> - vdda-pll-supply = <&vreg_l12a_1p8>;
> - vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
> -
> - qcom,imp-res-offset-value = <8>;
> - qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
> - qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
> - qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
> -};
> -
> -&usb_1_qmpphy {
> - status = "okay";
> -
> - vdda-phy-supply = <&vreg_l26a_1p2>;
> - vdda-pll-supply = <&vreg_l1a_0p875>;
> -};
> -
> -&venus {
> - status = "okay";
> - firmware-name = "qcom/sdm845/beryllium/venus.mbn";
> -};
> -
> -&wcd9340{
> - pinctrl-0 = <&wcd_intr_default>;
> - pinctrl-names = "default";
> - clock-names = "extclk";
> - clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
> - reset-gpios = <&tlmm 64 0>;
> - vdd-buck-supply = <&vreg_s4a_1p8>;
> - vdd-buck-sido-supply = <&vreg_s4a_1p8>;
> - vdd-tx-supply = <&vreg_s4a_1p8>;
> - vdd-rx-supply = <&vreg_s4a_1p8>;
> - vdd-io-supply = <&vreg_s4a_1p8>;
> - qcom,micbias1-microvolt = <2700000>;
> - qcom,micbias2-microvolt = <1800000>;
> - qcom,micbias3-microvolt = <2700000>;
> - qcom,micbias4-microvolt = <2700000>;
> -};
> -
> -&wifi {
> - status = "okay";
> -
> - vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
> - vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
> - vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
> - vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
> - vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
> -};
> -
> -/* PINCTRL - additions to nodes defined in sdm845.dtsi */
> -
> -&qup_uart6_default {
> - pinmux {
> - pins = "gpio45", "gpio46", "gpio47", "gpio48";
> - function = "qup6";
> - };
> -
> - cts {
> - pins = "gpio45";
> - bias-disable;
> - };
> -
> - rts-tx {
> - pins = "gpio46", "gpio47";
> - drive-strength = <2>;
> - bias-disable;
> - };
> -
> - rx {
> - pins = "gpio48";
> - bias-pull-up;
> - };
> };
> --
> 2.37.1
>
Powered by blists - more mailing lists