linux-kernel - Re: [PATCH 1/2] dmaengine: ti: k3-udma: Respond TX done if DMA_PREP

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <a30e917d-e031-3829-36fb-b897e971825f@ti.com>
Date:   Mon, 5 Sep 2022 08:32:45 +0530
From:   Vaishnav Achath <vaishnav.a@...com>
To:     Péter Ujfalusi <peter.ujfalusi@...il.com>,
        <vkoul@...nel.org>, <broonie@...nel.org>,
        <dmaengine@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
        <linux-spi@...r.kernel.org>
CC:     <vigneshr@...com>, <kishon@...com>,
        Vaishnav Achath <vaishnav.a@...com>
Subject: Re: [PATCH 1/2] dmaengine: ti: k3-udma: Respond TX done if
 DMA_PREP_INTERRUPT is not requested

Hi Peter,

On 02/09/22 19:50, Péter Ujfalusi wrote:
> Hi Achath,
> 
> On 23/08/2022 09:57, Vaishnav Achath wrote:
>> Hi Peter,
>>
>> On 22/08/22 18:42, Péter Ujfalusi wrote:
>>>
>>>
>>> On 22/08/2022 12:15, Vaishnav Achath wrote:
>>>> When the DMA consumer driver does not expect the callback for TX done,
>>>> There is no need to perform the channel RT byte counter calculations
>>>> and estimate the completion but return complete on first attempt itself.
>>>> This assumes that the consumer who did not request DMA_PREP_INTERRUPT
>>>> has its own mechanism for understanding TX completion, example: MCSPI
>>>> EOW interrupt can be used as TX completion signal for a SPI transaction.
>>>
>>> The check is in place to make sure that we don't leave stale data in the
>>> DMA fabric.
>>> If you drop the check then it is going to be possible that some TX data
>>> is going to be lost.
>>> Could be one out of 10K transfers or 100K, but if that happens it is not
>>> going to be easy to figure out.
>>> Let's say we go the packet back, but PDMA is still have data to send and
>>> the IP stops transmitting (externally clocked bus, some delay, etc).
>>> Is it going to be OK to disable the channel?
>>>
>> Thanks for the feedback, yes the check is necessary for most of the cases
>> but there needs to be  a way to disable the check for consumers which can
>> identify the end of transaction using some other internal mechanism/interrupt.
>>
>> For example the MCSPI controller has an End of Word(EOW) interrupt when the
>> said number of bytes has been clocked out, in this case the EOW interrupt
>> being raised guarantees that there is no stale data in DMA fabric.Using
>> the EOW interrupt to identify the completion of a transaction significantly
>> improves the transaction speed since we need not now wait for the slower DMA
>> TX completion calculation.
>>
>> This commit tries to bypass the check only if the consumer did not request
>> it by not passing the DMA_PREP_INTERRUPT flag, in other cases the check
>> should not be bypassed.
> 
> Let me think about over the weekend... Do you have performance numbers for this
> change?
> 
Thank you, yes we tested mainly for the SPI cases(Master and Slave mode), there
we saw a peak delay of 400ms for transaction completion and this varied with CPU
load, after adding the patch to not wait for DMA TX completion and use EOW
interrupt the peak latency reduced to 2ms.
> If we make sure that this is only affecting non cyclic transfers with a in code
> comment to explain the expectations from the user I think this can be safe.
> \
Sure I will add this in the next revision.
>>
>>>>
>>>> Signed-off-by: Vaishnav Achath <vaishnav.a@...com>
>>>> ---
>>>>   drivers/dma/ti/k3-udma.c | 5 ++++-
>>>>   1 file changed, 4 insertions(+), 1 deletion(-)
>>>>
>>>> diff --git a/drivers/dma/ti/k3-udma.c b/drivers/dma/ti/k3-udma.c
>>>> index 39b330ada200..03d579068453 100644
>>>> --- a/drivers/dma/ti/k3-udma.c
>>>> +++ b/drivers/dma/ti/k3-udma.c
>>>> @@ -263,6 +263,7 @@ struct udma_chan_config {
>>>>       enum udma_tp_level channel_tpl; /* Channel Throughput Level */
>>>>         u32 tr_trigger_type;
>>>> +    unsigned long tx_flags;
>>>>         /* PKDMA mapped channel */
>>>>       int mapped_channel_id;
>>>> @@ -1057,7 +1058,7 @@ static bool udma_is_desc_really_done(struct udma_chan
>>>> *uc, struct udma_desc *d)
>>>>         /* Only TX towards PDMA is affected */
>>>>       if (uc->config.ep_type == PSIL_EP_NATIVE ||
>>>> -        uc->config.dir != DMA_MEM_TO_DEV)
>>>> +        uc->config.dir != DMA_MEM_TO_DEV || !(uc->config.tx_flags &
>>>> DMA_PREP_INTERRUPT))
>>>>           return true;
>>>>         peer_bcnt = udma_tchanrt_read(uc, UDMA_CHAN_RT_PEER_BCNT_REG);
>>>> @@ -3418,6 +3419,8 @@ udma_prep_slave_sg(struct dma_chan *chan, struct
>>>> scatterlist *sgl,
>>>>       if (!burst)
>>>>           burst = 1;
>>>>   +    uc->config.tx_flags = tx_flags;
>>>> +
>>>>       if (uc->config.pkt_mode)
>>>>           d = udma_prep_slave_sg_pkt(uc, sgl, sglen, dir, tx_flags,
>>>>                          context);
>>>
>>
> 

-- 
Regards,
Vaishnav