linux-kernel - [PATCH 2/2] usb: dwc3: xilinx: fix usb3 non-wakeup source resume failure

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <20220912111017.901321-3-piyush.mehta@amd.com>
Date:   Mon, 12 Sep 2022 16:40:17 +0530
From:   Piyush Mehta <piyush.mehta@....com>
To:     <balbi@...nel.org>, <gregkh@...uxfoundation.org>,
        <michal.simek@...inx.com>, <michal.simek@....com>,
        <linux-usb@...r.kernel.org>,
        <linux-arm-kernel@...ts.infradead.org>,
        <linux-kernel@...r.kernel.org>
CC:     <git@....com>, <siva.durga.prasad.paladugu@....com>,
        Piyush Mehta <piyush.mehta@....com>
Subject: [PATCH 2/2] usb: dwc3: xilinx: fix usb3 non-wakeup source resume failure

When USB is in super-speed mode and disabled as a wakeup source,
observed that on the resume path, lanes have not been configured
properly in the phy-zynqmp driver.
As a result, after the resume, USB device detection failed on host.

To resolved the above issue, added phy_init on resume and phy_exit
on suspend path, to configure the GT lanes correctly.
The re-initialization of phy, reset the device and re-enumerate
the USB subsystem.

This use-case is specific to Xilinx ZynqMP SoC.

Signed-off-by: Piyush Mehta <piyush.mehta@....com>
---
 drivers/usb/dwc3/dwc3-xilinx.c | 30 +++++++++++++++++++++---------
 1 file changed, 21 insertions(+), 9 deletions(-)

diff --git a/drivers/usb/dwc3/dwc3-xilinx.c b/drivers/usb/dwc3/dwc3-xilinx.c
index a0d0280a045e..8607d4c23283 100644
--- a/drivers/usb/dwc3/dwc3-xilinx.c
+++ b/drivers/usb/dwc3/dwc3-xilinx.c
@@ -47,6 +47,7 @@ struct dwc3_xlnx {
 	struct device			*dev;
 	void __iomem			*regs;
 	int				(*pltfm_init)(struct dwc3_xlnx *data);
+	struct phy			*usb3_phy;
 };
 
 static void dwc3_xlnx_mask_phy_rst(struct dwc3_xlnx *priv_data, bool mask)
@@ -100,13 +101,12 @@ static int dwc3_xlnx_init_zynqmp(struct dwc3_xlnx *priv_data)
 	struct device		*dev = priv_data->dev;
 	struct reset_control	*crst, *hibrst, *apbrst;
 	struct gpio_desc	*reset_gpio;
-	struct phy		*usb3_phy;
 	int			ret = 0;
 	u32			reg;
 
-	usb3_phy = devm_phy_optional_get(dev, "usb3-phy");
-	if (IS_ERR(usb3_phy)) {
-		ret = PTR_ERR(usb3_phy);
+	priv_data->usb3_phy = devm_phy_optional_get(dev, "usb3-phy");
+	if (IS_ERR(priv_data->usb3_phy)) {
+		ret = PTR_ERR(priv_data->usb3_phy);
 		dev_err_probe(dev, ret,
 			      "failed to get USB3 PHY\n");
 		goto err;
@@ -121,7 +121,7 @@ static int dwc3_xlnx_init_zynqmp(struct dwc3_xlnx *priv_data)
 	 * in use but the usb3-phy entry is missing from the device tree.
 	 * Therefore, skip these operations in this case.
 	 */
-	if (!usb3_phy)
+	if (!priv_data->usb3_phy)
 		goto skip_usb3_phy;
 
 	crst = devm_reset_control_get_exclusive(dev, "usb_crst");
@@ -166,9 +166,9 @@ static int dwc3_xlnx_init_zynqmp(struct dwc3_xlnx *priv_data)
 		goto err;
 	}
 
-	ret = phy_init(usb3_phy);
+	ret = phy_init(priv_data->usb3_phy);
 	if (ret < 0) {
-		phy_exit(usb3_phy);
+		phy_exit(priv_data->usb3_phy);
 		goto err;
 	}
 
@@ -196,9 +196,9 @@ static int dwc3_xlnx_init_zynqmp(struct dwc3_xlnx *priv_data)
 		goto err;
 	}
 
-	ret = phy_power_on(usb3_phy);
+	ret = phy_power_on(priv_data->usb3_phy);
 	if (ret < 0) {
-		phy_exit(usb3_phy);
+		phy_exit(priv_data->usb3_phy);
 		goto err;
 	}
 
@@ -350,6 +350,8 @@ static int __maybe_unused dwc3_xlnx_suspend(struct device *dev)
 {
 	struct dwc3_xlnx *priv_data = dev_get_drvdata(dev);
 
+	phy_exit(priv_data->usb3_phy);
+
 	/* Disable the clocks */
 	clk_bulk_disable(priv_data->num_clocks, priv_data->clks);
 
@@ -365,6 +367,16 @@ static int __maybe_unused dwc3_xlnx_resume(struct device *dev)
 	if (ret)
 		return ret;
 
+	ret = phy_init(priv_data->usb3_phy);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_power_on(priv_data->usb3_phy);
+	if (ret < 0) {
+		phy_exit(priv_data->usb3_phy);
+		return ret;
+	}
+
 	return 0;
 }
 
-- 
2.25.1