| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <eeca0eef-e73e-847f-de54-1511dddff842@microchip.com>
Date: Tue, 13 Sep 2022 06:37:21 +0000
From: <Claudiu.Beznea@...rochip.com>
To: <Jerry.Ray@...rochip.com>, <krzysztof.kozlowski+dt@...aro.org>,
<robh+dt@...nel.org>, <Nicolas.Ferre@...rochip.com>,
<alexandre.belloni@...tlin.com>, <devicetree@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-kernel@...r.kernel.org>
Subject: Re: [linux][PATCH v9 2/2] dts: arm: at91: Add SAMA5D3-EDS Board
On 09.09.2022 19:30, Jerry Ray wrote:
> The SAMA5D3-EDS board is an Ethernet Development Platform allowing for
> evaluating many Microchip ethernet switch and PHY products. Various
> daughter cards can connect via an RGMII connector or an RMII connector.
>
> The EDS board is not intended for stand-alone use and has no ethernet
> capabilities when no daughter board is connected. As such, this device
> tree is intended to be used with a DT overlay defining the add-on board.
> To better ensure consistency, some items are defined here as a form of
> documentation so that all add-on overlays will use the same terms.
>
> Link: https://www.microchip.com/en-us/development-tool/SAMA5D3-ETHERNET-DEVELOPMENT-SYSTEM
> Signed-off-by: Jerry Ray <jerry.ray@...rochip.com>
> ---
> v8->v9:
> - Changed node name from gpio to gpio-inputs
Why not gpio-keys as all other DTSes are doing? Anyway, I can change it
while applying.
Thank you,
Claudiu Beznea
> v7->v8:
> - correcting patch subject line.
> v6->v7:
> - Renamed regulators, making things more consistent.
> - Made slow_xtal and main_xtal entries direct overrides.
> v5->v6:
> - Replaced underscores in names where I can, improving naming.
> v4->v5:
> - patch now applies to v6.0-rc2
> v3->v4:
> - Fixed regulators as necessary to get the board to boot from SD Card.
> v2->v3:
> - Alphabetized pinctrl entries.
> - cleaned up a warning in the regulators section.
> - License tweaked to 'OR MIT'
> - Included Makefile change
> v1->v2:
> - Modified the compatible field in the device tree to reflect Microchip
> Ethernet Development System Board.
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/at91-sama5d3_eds.dts | 307 +++++++++++++++++++++++++
> 2 files changed, 308 insertions(+)
> create mode 100644 arch/arm/boot/dts/at91-sama5d3_eds.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 05d8aef6e5d2..e92e639a2dc3 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -61,6 +61,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
> at91-sama5d2_icp.dtb \
> at91-sama5d2_ptc_ek.dtb \
> at91-sama5d2_xplained.dtb \
> + at91-sama5d3_eds.dtb \
> at91-sama5d3_ksz9477_evb.dtb \
> at91-sama5d3_xplained.dtb \
> at91-dvk_som60.dtb \
> diff --git a/arch/arm/boot/dts/at91-sama5d3_eds.dts b/arch/arm/boot/dts/at91-sama5d3_eds.dts
> new file mode 100644
> index 000000000000..bae6819217e0
> --- /dev/null
> +++ b/arch/arm/boot/dts/at91-sama5d3_eds.dts
> @@ -0,0 +1,307 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR MIT
> +/*
> + * at91-sama5d3_eds.dts - Device Tree file for the SAMA5D3 Ethernet
> + * Development System board.
> + *
> + * Copyright (C) 2022 Microchip Technology Inc. and its subsidiaries
> + *
> + * Author: Jerry Ray <jerry.ray@...rochip.com>
> + */
> +/dts-v1/;
> +#include "sama5d36.dtsi"
> +
> +/ {
> + model = "SAMA5D3 Ethernet Development System";
> + compatible = "microchip,sama5d3-eds", "atmel,sama5d36",
> + "atmel,sama5d3", "atmel,sama5";
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + gpio-inputs {
> + compatible = "gpio-keys";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_key_gpio>;
> +
> + button-3 {
> + label = "PB_USER";
> + gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
> + linux,code = <0x104>;
> + wakeup-source;
> + };
> + };
> +
> + memory@...00000 {
> + reg = <0x20000000 0x10000000>;
> + };
> +
> + vcc_3v3_reg: regulator-1 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vcc_2v5_reg: regulator-2 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_2V5";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + regulator-always-on;
> + vin-supply = <&vcc_3v3_reg>;
> + };
> +
> + vcc_1v8_reg: regulator-3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + vin-supply = <&vcc_3v3_reg>;
> + };
> +
> + vcc_1v2_reg: regulator-4 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_1V2";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + };
> +
> + vcc_mmc0_reg: regulator-5 {
> + compatible = "regulator-fixed";
> + regulator-name = "mmc0-card-supply";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_vcc_mmc0_reg_gpio>;
> + gpio = <&pioE 2 GPIO_ACTIVE_LOW>;
> + };
> +};
> +
> +&can0 {
> + status = "okay";
> +};
> +
> +&dbgu {
> + status = "okay";
> +};
> +
> +&ebi {
> + pinctrl-0 = <&pinctrl_ebi_nand_addr>;
> + pinctrl-names = "default";
> + status = "okay";
> +
> + nand_controller: nand-controller {
> + status = "okay";
> +
> + nand@3 {
> + reg = <0x3 0x0 0x2>;
> + atmel,rb = <0>;
> + nand-bus-width = <8>;
> + nand-ecc-mode = "hw";
> + nand-ecc-strength = <4>;
> + nand-ecc-step-size = <512>;
> + nand-on-flash-bbt;
> + label = "atmel_nand";
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + at91bootstrap@0 {
> + label = "at91bootstrap";
> + reg = <0x0 0x40000>;
> + };
> +
> + bootloader@...00 {
> + label = "bootloader";
> + reg = <0x40000 0xc0000>;
> + };
> +
> + bootloaderenvred@...000 {
> + label = "bootloader env redundant";
> + reg = <0x100000 0x40000>;
> + };
> +
> + bootloaderenv@...000 {
> + label = "bootloader env";
> + reg = <0x140000 0x40000>;
> + };
> +
> + dtb@...000 {
> + label = "device tree";
> + reg = <0x180000 0x80000>;
> + };
> +
> + kernel@...000 {
> + label = "kernel";
> + reg = <0x200000 0x600000>;
> + };
> +
> + rootfs@...000 {
> + label = "rootfs";
> + reg = <0x800000 0x0f800000>;
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c0 {
> + pinctrl-0 = <&pinctrl_i2c0_pu>;
> + status = "okay";
> +};
> +
> +&i2c1 {
> + status = "okay";
> +};
> +
> +&i2c2 {
> + pinctrl-0 = <&pinctrl_i2c2_pu>;
> + status = "okay";
> +};
> +
> +&main_xtal {
> + clock-frequency = <12000000>;
> +};
> +
> +&mmc0 {
> + pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3
> + &pinctrl_mmc0_dat4_7 &pinctrl_mmc0_cd>;
> + vmmc-supply = <&vcc_mmc0_reg>;
> + vqmmc-supply = <&vcc_3v3_reg>;
> + status = "okay";
> + slot@0 {
> + reg = <0>;
> + bus-width = <8>;
> + cd-gpios = <&pioE 0 GPIO_ACTIVE_LOW>;
> + };
> +};
> +
> +&pinctrl {
> + board {
> + pinctrl_i2c0_pu: i2c0-pu {
> + atmel,pins =
> + <AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
> + <AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
> + };
> +
> + pinctrl_i2c2_pu: i2c2-pu {
> + atmel,pins =
> + <AT91_PIOA 18 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>,
> + <AT91_PIOA 19 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
> + };
> +
> + pinctrl_key_gpio: key-gpio-0 {
> + atmel,pins =
> + <AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
> + };
> +
> + pinctrl_mmc0_cd: mmc0-cd {
> + atmel,pins =
> + <AT91_PIOE 0 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
> + };
> +
> + /* Reserved for reset signal to the RGMII connector. */
> + pinctrl_rgmii_rstn: rgmii-rstn {
> + atmel,pins =
> + <AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
> + };
> +
> + /* Reserved for an interrupt line from the RMII and RGMII connectors. */
> + pinctrl_spi_irqn: spi-irqn {
> + atmel,pins =
> + <AT91_PIOB 28 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
> + };
> +
> + pinctrl_spi0_cs: spi0-cs-default {
> + atmel,pins =
> + <AT91_PIOD 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
> + AT91_PIOD 16 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> +
> + pinctrl_spi1_cs: spi1-cs-default {
> + atmel,pins = <AT91_PIOC 25 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
> + AT91_PIOC 28 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> +
> + pinctrl_usba_vbus: usba-vbus {
> + atmel,pins =
> + <AT91_PIOE 9 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
> + };
> +
> + pinctrl_usb_default: usb-default {
> + atmel,pins =
> + <AT91_PIOE 3 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
> + AT91_PIOE 4 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> +
> + /* Reserved for VBUS fault interrupt. */
> + pinctrl_vbusfault_irqn: vbusfault-irqn {
> + atmel,pins =
> + <AT91_PIOE 5 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
> + };
> +
> + pinctrl_vcc_mmc0_reg_gpio: vcc-mmc0-reg-gpio-default {
> + atmel,pins = <AT91_PIOE 2 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
> + };
> + };
> +};
> +
> +&slow_xtal {
> + clock-frequency = <32768>;
> +};
> +
> +&spi0 {
> + pinctrl-names = "default", "cs";
> + pinctrl-1 = <&pinctrl_spi0_cs>;
> + cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
> + status = "okay";
> +};
> +
> +&spi1 {
> + pinctrl-names = "default", "cs";
> + pinctrl-1 = <&pinctrl_spi1_cs>;
> + cs-gpios = <&pioC 25 0>, <0>, <0>, <&pioC 28 0>;
> + status = "okay";
> +};
> +
> +&tcb0 {
> + timer0: timer@0 {
> + compatible = "atmel,tcb-timer";
> + reg = <0>;
> + };
> +
> + timer1: timer@1 {
> + compatible = "atmel,tcb-timer";
> + reg = <1>;
> + };
> +};
> +
> +&usb0 { /* USB Device port with VBUS detection. */
> + atmel,vbus-gpio = <&pioE 9 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usba_vbus>;
> + status = "okay";
> +};
> +
> +&usb1 { /* 3-port Host. First port is unused. */
> + atmel,vbus-gpio = <0
> + &pioE 3 GPIO_ACTIVE_HIGH
> + &pioE 4 GPIO_ACTIVE_HIGH
> + >;
> + num-ports = <3>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usb_default>;
> + status = "okay";
> +};
> +
> +&usb2 {
> + status = "okay";
> +};
Powered by blists - more mailing lists