linux-kernel - [PATCH v7 0/4] ECAP support on TI AM62x SoC

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [thread-next>] [day] [month] [year] [list]

Message-Id: <20220921100627.124085-1-jpanis@baylibre.com>
Date:   Wed, 21 Sep 2022 12:06:23 +0200
From:   Julien Panis <jpanis@...libre.com>
To:     william.gray@...aro.org, robh+dt@...nel.org,
        krzysztof.kozlowski+dt@...aro.org
Cc:     linux-iio@...r.kernel.org, linux-kernel@...r.kernel.org,
        devicetree@...r.kernel.org, mranostay@...com
Subject: [PATCH v7 0/4] ECAP support on TI AM62x SoC

The Enhanced Capture (ECAP) module can be used to timestamp events
detected on signal input pin. It can be used for time measurements
of pulse train signals.

ECAP module includes 4 timestamp capture registers. For all 4 sequenced
timestamp capture events (0->1->2->3->0->...), edge polarity (falling/rising
edge) can be selected.

This driver leverages counter subsystem to :
- select edge polarity for all 4 capture events (event mode)
- log timestamps for each capture event
Event polarity, and CAP0/1/2/3 timestamps give all the information
about the input pulse train. Further information can easily be computed :
period and/or duty cycle if frequency is constant, elapsed time between
pulses, etc...

Modifications since v6:
	- Leverage counter array components (RFC PATCH v5)
	- Remove the redundant doc of 'capture' items in sysfs-bus-counter ABI file
	- Add driver info to MAINTAINERS file

Userspace commands :
	### CLOCK SIGNAL ###
	cd /sys/bus/counter/devices/counter0/signal0

	# Get frequency
	cat frequency

	### INPUT SIGNAL ###
	cd /sys/bus/counter/devices/counter0/signal1

	# Get polarity for each capture event
	cat polarity0
	cat polarity1
	cat polarity2
	cat polarity3

	# Set polarity for each capture event
	echo positive > polarity0
	echo negative > polarity1
	echo positive > polarity2
	echo negative > polarity3

	### COUNT ###
	cd /sys/bus/counter/devices/counter0/count0

	# Get ceiling (counter max value)
	cat ceiling

	# Reset number of overflows & current timebase counter value
	echo 0 > num_overflows
	echo 0 > count

	# Run ECAP
	echo 1 > enable

	# Get number of overflows & current timebase counter value
	cat num_overflows
	cat count

	# Get captured timestamps
	cat capture0
	cat capture1
	cat capture2
	cat capture3

	# Note that counter watches can also be used to get
	# data from userspace application
	# -> see tools/counter/counter_example.c

	# Pause ECAP
	echo 0 > enable

Julien Panis (4):
  dt-bindings: counter: add ti,am62-ecap-capture.yaml
  Documentation: ABI: sysfs-bus-counter: add frequency & num_overflows
    items
  counter: ti-ecap-capture: capture driver support for ECAP
  MAINTAINERS: add TI ECAP driver info

 Documentation/ABI/testing/sysfs-bus-counter   |  14 +
 .../counter/ti,am62-ecap-capture.yaml         |  61 ++
 MAINTAINERS                                   |   6 +
 drivers/counter/Kconfig                       |  15 +
 drivers/counter/Makefile                      |   1 +
 drivers/counter/ti-ecap-capture.c             | 614 ++++++++++++++++++
 6 files changed, 711 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/counter/ti,am62-ecap-capture.yaml
 create mode 100644 drivers/counter/ti-ecap-capture.c

-- 
2.37.3