| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20220925204416.715687-4-matti.lehtimaki@gmail.com>
Date: Sun, 25 Sep 2022 23:44:15 +0300
From: Matti Lehtimäki <matti.lehtimaki@...il.com>
To: linux-arm-msm@...r.kernel.org
Cc: ~postmarketos/upstreaming@...ts.sr.ht, phone-devel@...r.kernel.org,
Matti Lehtimäki <matti.lehtimaki@...il.com>,
Arnd Bergmann <arnd@...db.de>, Olof Johansson <olof@...om.net>,
soc@...nel.org, Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Andy Gross <agross@...nel.org>,
Bjorn Andersson <bjorn.andersson@...aro.org>,
Konrad Dybcio <konrad.dybcio@...ainline.org>,
linux-arm-kernel@...ts.infradead.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org
Subject: [PATCH v5 3/3] ARM: dts: qcom: Add support for Samsung Galaxy Tab 4 10.1 (SM-T530)
Add a device tree for the Samsung Galaxy Tab 4 10.1 (SM-T530) wifi tablet
based on the apq8026 platform.
Currently supported are accelerometer sensor, hall sensor,
internal storage, physical buttons (power & volume), screen
(based on simple-framebuffer set up by the bootloader), sdcard,
touchscreen and USB.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@...il.com>
---
Changes in v5:
- Rename pm8226-regulators node to fix issue reported by make dtbs_check
Changes in v4:
- Move delete-node to memory-region
- Move usb-switch node to blsp_i2c4
Changes in v3:
- Fix sdhc_2 bus width
- Reorder includes
Changes in v2:
- Change codename to matisse-wifi
- Remove msm-id, not needed when lk2nd is used
- Remove unused labels from reserved memory regions
- Rename muic node
---
arch/arm/boot/dts/Makefile | 1 +
.../dts/qcom-apq8026-samsung-matisse-wifi.dts | 453 ++++++++++++++++++
2 files changed, 454 insertions(+)
create mode 100644 arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 05d8aef6e5d2..69f6bbcf90c6 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1027,6 +1027,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8016-sbc.dtb \
qcom-apq8026-asus-sparrow.dtb \
qcom-apq8026-lg-lenok.dtb \
+ qcom-apq8026-samsung-matisse-wifi.dtb \
qcom-apq8060-dragonboard.dtb \
qcom-apq8064-cm-qs600.dtb \
qcom-apq8064-ifc6410.dtb \
diff --git a/arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts b/arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts
new file mode 100644
index 000000000000..3029bc566832
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts
@@ -0,0 +1,453 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Matti Lehtimäki <matti.lehtimaki@...il.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "qcom-msm8226.dtsi"
+#include "qcom-pm8226.dtsi"
+
+/ {
+ model = "Samsung Galaxy Tab 4 10.1";
+ compatible = "samsung,matisse-wifi", "qcom,apq8026";
+ chassis-type = "tablet";
+
+ aliases {
+ mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+ mmc1 = &sdhc_2; /* SDC2 SD card slot */
+ display0 = &framebuffer0;
+ };
+
+ chosen {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ stdout-path = "display0";
+
+ framebuffer0: framebuffer@...0000 {
+ compatible = "simple-framebuffer";
+ reg = <0x3200000 0x800000>;
+ width = <1280>;
+ height = <800>;
+ stride = <(1280 * 3)>;
+ format = "r8g8b8";
+ };
+ };
+
+ gpio-hall-sensor {
+ compatible = "gpio-keys";
+
+ event-hall-sensor {
+ label = "Hall Effect Sensor";
+ gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+ interrupts = <&tlmm 110 IRQ_TYPE_EDGE_FALLING>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_LID>;
+ debounce-interval = <15>;
+ wakeup-source;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+
+ key-home {
+ label = "Home";
+ gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_HOMEPAGE>;
+ debounce-interval = <15>;
+ };
+
+ key-volume-down {
+ label = "Volume Down";
+ gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ debounce-interval = <15>;
+ };
+
+ key-volume-up {
+ label = "Volume Up";
+ gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ debounce-interval = <15>;
+ };
+ };
+
+ reg_tsp_1p8v: regulator-tsp-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "tsp_1p8v";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ gpio = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tsp_en_default_state>;
+ };
+
+ reg_tsp_3p3v: regulator-tsp-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "tsp_3p3v";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 73 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tsp_en1_default_state>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ framebuffer@...0000 {
+ reg = <0x3200000 0x800000>;
+ no-map;
+ };
+
+ mpss@...0000 {
+ reg = <0x08400000 0x1f00000>;
+ no-map;
+ };
+
+ mba@...0000 {
+ reg = <0x0a300000 0x100000>;
+ no-map;
+ };
+
+ reserved@...0000 {
+ reg = <0x0cb00000 0x700000>;
+ no-map;
+ };
+
+ wcnss@...0000 {
+ reg = <0x0d200000 0x700000>;
+ no-map;
+ };
+
+ adsp@...0000 {
+ reg = <0x0d900000 0x1800000>;
+ no-map;
+ };
+
+ venus@...0000 {
+ reg = <0x0f100000 0x500000>;
+ no-map;
+ };
+
+ /delete-node/ smem@...0000;
+ smem_region: smem@...0000 {
+ reg = <0xfa00000 0x100000>;
+ no-map;
+ };
+
+ reserved@...0000 {
+ reg = <0x0fb00000 0x260000>;
+ no-map;
+ };
+
+ rfsa@...0000 {
+ reg = <0x0fd60000 0x20000>;
+ no-map;
+ };
+
+ rmtfs@...0000 {
+ compatible = "qcom,rmtfs-mem";
+ reg = <0x0fd80000 0x180000>;
+ no-map;
+
+ qcom,client-id = <1>;
+ };
+ };
+};
+
+&blsp1_i2c2 {
+ status = "okay";
+
+ accelerometer@1d {
+ compatible = "st,lis2hh12";
+ reg = <0x1d>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <54 IRQ_TYPE_LEVEL_HIGH>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&accel_int_default_state>;
+
+ st,drdy-int-pin = <1>;
+
+ vdd-supply = <&pm8226_l19>;
+ vddio-supply = <&pm8226_lvs1>;
+ };
+};
+
+&blsp1_i2c4 {
+ status = "okay";
+
+ muic: usb-switch@25 {
+ compatible = "siliconmitus,sm5502-muic";
+ reg = <0x25>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <67 IRQ_TYPE_EDGE_FALLING>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&muic_int_default_state>;
+ };
+};
+
+&blsp1_i2c5 {
+ status = "okay";
+
+ touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ reg = <0x4a>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tsp_int_rst_default_state>;
+
+ reset-gpios = <&pm8226_gpios 6 GPIO_ACTIVE_LOW>;
+
+ vdd-supply = <®_tsp_1p8v>;
+ vdda-supply = <®_tsp_3p3v>;
+ };
+};
+
+&rpm_requests {
+ regulators {
+ compatible = "qcom,rpm-pm8226-regulators";
+
+ pm8226_s3: s3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ pm8226_s4: s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8226_s5: s5 {
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+ };
+
+ pm8226_l1: l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ pm8226_l2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ pm8226_l3: l3 {
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1337500>;
+ regulator-always-on;
+ };
+
+ pm8226_l4: l4 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ pm8226_l5: l5 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ pm8226_l6: l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ pm8226_l7: l7 {
+ regulator-min-microvolt = <1850000>;
+ regulator-max-microvolt = <1850000>;
+ };
+
+ pm8226_l8: l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ pm8226_l9: l9 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ pm8226_l10: l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8226_l12: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8226_l14: l14 {
+ regulator-min-microvolt = <2750000>;
+ regulator-max-microvolt = <2750000>;
+ };
+
+ pm8226_l15: l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8226_l16: l16 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3350000>;
+ };
+
+ pm8226_l17: l17 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-system-load = <200000>;
+ regulator-allow-set-load;
+ regulator-always-on;
+ };
+
+ pm8226_l18: l18 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8226_l19: l19 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ pm8226_l20: l20 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ };
+
+ pm8226_l21: l21 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8226_l22: l22 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ pm8226_l23: l23 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8226_l24: l24 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1350000>;
+ };
+
+ pm8226_l25: l25 {
+ regulator-min-microvolt = <1775000>;
+ regulator-max-microvolt = <2125000>;
+ };
+
+ pm8226_l26: l26 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ pm8226_l27: l27 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8226_l28: l28 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8226_lvs1: lvs1 {};
+ };
+};
+
+&sdhc_1 {
+ status = "okay";
+
+ vmmc-supply = <&pm8226_l17>;
+ vqmmc-supply = <&pm8226_l6>;
+
+ bus-width = <8>;
+ non-removable;
+};
+
+&sdhc_2 {
+ status = "okay";
+
+ vmmc-supply = <&pm8226_l18>;
+ vqmmc-supply = <&pm8226_l21>;
+
+ bus-width = <4>;
+ cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+};
+
+&tlmm {
+ accel_int_default_state: accel-int-default-state {
+ pins = "gpio54";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ muic_int_default_state: muic-int-default-state {
+ pins = "gpio67";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ tsp_en_default_state: tsp-en-default-state {
+ pins = "gpio31";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ tsp_en1_default_state: tsp-en1-default-state {
+ pins = "gpio73";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ tsp_int_rst_default_state: tsp-int-rst-default-state {
+ pins = "gpio17";
+ function = "gpio";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+};
+
+&usb {
+ status = "okay";
+ extcon = <&muic>, <&muic>;
+};
+
+&usb_hs_phy {
+ extcon = <&muic>;
+ v1p8-supply = <&pm8226_l10>;
+ v3p3-supply = <&pm8226_l20>;
+};
--
2.34.1
Powered by blists - more mailing lists