| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20220928110509.13544-2-ilpo.jarvinen@linux.intel.com>
Date: Wed, 28 Sep 2022 14:05:06 +0300
From: Ilpo Järvinen <ilpo.jarvinen@...ux.intel.com>
To: Jiri Slaby <jirislaby@...nel.org>,
Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
linux-serial <linux-serial@...r.kernel.org>,
Jonathan Corbet <corbet@....net>, linux-doc@...r.kernel.org,
linux-kernel@...r.kernel.org
Cc: Andy Shevchenko <andy.shevchenko@...il.com>,
Ilpo Järvinen <ilpo.jarvinen@...ux.intel.com>
Subject: [PATCH v3 1/4] serial: Convert serial_rs485 to kernel doc
Convert struct serial_rs485 comments to kernel doc format and include
it into documentation.
Suggested-by: Andy Shevchenko <andy.shevchenko@...il.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@...ux.intel.com>
---
.../driver-api/serial/serial-rs485.rst | 13 ++--
include/uapi/linux/serial.h | 62 ++++++++++++-------
2 files changed, 48 insertions(+), 27 deletions(-)
diff --git a/Documentation/driver-api/serial/serial-rs485.rst b/Documentation/driver-api/serial/serial-rs485.rst
index 6ebad75c74ed..264e4b753713 100644
--- a/Documentation/driver-api/serial/serial-rs485.rst
+++ b/Documentation/driver-api/serial/serial-rs485.rst
@@ -29,11 +29,11 @@ RS485 Serial Communications
3. Data Structures Already Available in the Kernel
==================================================
- The Linux kernel provides the serial_rs485 structure (see [1]) to handle
- RS485 communications. This data structure is used to set and configure RS485
+ The Linux kernel provides the serial_rs485 structure to handle RS485
+ communications. This data structure is used to set and configure RS485
parameters in the platform data and in ioctls.
- The device tree can also provide RS485 boot time parameters (see [2]
+ The device tree can also provide RS485 boot time parameters (see [1]
for bindings). The driver is in charge of filling this data structure from
the values given by the device tree.
@@ -47,6 +47,9 @@ RS485 Serial Communications
for the uart_port. TIOCGRS485 ioctl can be used to read back the
serial_rs485 structure matching to the current configuration.
+.. kernel-doc:: include/uapi/linux/serial.h
+ :identifiers: serial_rs485
+
4. Usage from user-level
========================
@@ -126,6 +129,4 @@ RS485 Serial Communications
6. References
=============
- [1] include/uapi/linux/serial.h
-
- [2] Documentation/devicetree/bindings/serial/rs485.txt
+ [1] Documentation/devicetree/bindings/serial/rs485.txt
diff --git a/include/uapi/linux/serial.h b/include/uapi/linux/serial.h
index cea06924b295..6e347eb10b1f 100644
--- a/include/uapi/linux/serial.h
+++ b/include/uapi/linux/serial.h
@@ -107,37 +107,57 @@ struct serial_icounter_struct {
int reserved[9];
};
-/*
+/**
+ * struct serial_rs485 - serial interface for controlling RS485 settings.
+ * @flags: RS485 feature flags.
+ * @delay_rts_before_send: Delay before send (milliseconds).
+ * @delay_rts_after_send: Delay after send (milliseconds).
+ * @addr_recv: Receive filter for RS485 addressing mode
+ * (used only when %SER_RS485_ADDR_RECV is set).
+ * @addr_dest: Destination address for RS485 addressing mode
+ * (used only when %SER_RS485_ADDR_DEST is set).
+ * @padding0: Padding (set to zero).
+ * @padding1: Padding (set to zero).
+ * @padding: Deprecated, use @padding0 and @padding1 instead.
+ * Do not use with @addr_recv and @addr_dest (due to
+ * overlap).
+ *
* Serial interface for controlling RS485 settings on chips with suitable
* support. Set with TIOCSRS485 and get with TIOCGRS485 if supported by your
* platform. The set function returns the new state, with any unsupported bits
* reverted appropriately.
+ *
+ * serial_rs485::flags bits are:
+ *
+ * * %SER_RS485_ENABLED - RS485 enabled.
+ * * %SER_RS485_RTS_ON_SEND - Logical level for RTS pin when sending.
+ * * %SER_RS485_RTS_AFTER_SEND - Logical level for RTS pin after sent.
+ * * %SER_RS485_RX_DURING_TX - Full-duplex RS485 line.
+ * * %SER_RS485_TERMINATE_BUS - Enable bus termination (if supported).
+ * * %SER_RS485_ADDRB - Enable RS485 addressing mode.
+ * * %SER_RS485_ADDR_RECV - Receive address filter (enables @addr_recv).
+ * Requires %SER_RS485_ADDRB.
+ * * %SER_RS485_ADDR_DEST - Destination address (enables @addr_dest).
+ * Requires %SER_RS485_ADDRB.
*/
-
struct serial_rs485 {
- __u32 flags; /* RS485 feature flags */
-#define SER_RS485_ENABLED (1 << 0) /* If enabled */
-#define SER_RS485_RTS_ON_SEND (1 << 1) /* Logical level for
- RTS pin when
- sending */
-#define SER_RS485_RTS_AFTER_SEND (1 << 2) /* Logical level for
- RTS pin after sent*/
+ __u32 flags;
+#define SER_RS485_ENABLED (1 << 0)
+#define SER_RS485_RTS_ON_SEND (1 << 1)
+#define SER_RS485_RTS_AFTER_SEND (1 << 2)
#define SER_RS485_RX_DURING_TX (1 << 4)
-#define SER_RS485_TERMINATE_BUS (1 << 5) /* Enable bus
- termination
- (if supported) */
-
-/* RS-485 addressing mode */
-#define SER_RS485_ADDRB (1 << 6) /* Enable addressing mode */
-#define SER_RS485_ADDR_RECV (1 << 7) /* Receive address filter */
-#define SER_RS485_ADDR_DEST (1 << 8) /* Destination address */
+#define SER_RS485_TERMINATE_BUS (1 << 5)
+#define SER_RS485_ADDRB (1 << 6)
+#define SER_RS485_ADDR_RECV (1 << 7)
+#define SER_RS485_ADDR_DEST (1 << 8)
- __u32 delay_rts_before_send; /* Delay before send (milliseconds) */
- __u32 delay_rts_after_send; /* Delay after send (milliseconds) */
+ __u32 delay_rts_before_send;
+ __u32 delay_rts_after_send;
- /* The fields below are defined by flags */
+ /* private: The fields below are defined by flags */
union {
- __u32 padding[5]; /* Memory is cheap, new structs are a pain */
+ /* private: Memory is cheap, new structs are a pain. */
+ __u32 padding[5];
struct {
__u8 addr_recv;
--
2.30.2
Powered by blists - more mailing lists