[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <ad743621-8e2d-23f9-8c44-53f6681aa134@linaro.org>
Date: Sat, 1 Oct 2022 11:14:15 +0200
From: Krzysztof Kozlowski <krzysztof.kozlowski@...aro.org>
To: Melody Olvera <quic_molvera@...cinc.com>,
Andy Gross <agross@...nel.org>,
Bjorn Andersson <bjorn.andersson@...aro.org>,
Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>
Cc: linux-arm-msm@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org
Subject: Re: [PATCH 03/19] arm64: dts: qcom: qdru1000: Add tlmm nodes
On 01/10/2022 05:06, Melody Olvera wrote:
> Add tlmm node for the QDU1000 and QRU1000 SoCs and the uart pin
> configuration.
The patchset should be squashed with previous. There is no point in
bringing support piece by piece. You can bring support in steps if you
submissions are separate in time. But if you have everything ready -
your patch must be complete and bisectable.
>
> Signed-off-by: Melody Olvera <quic_molvera@...cinc.com>
> ---
> arch/arm64/boot/dts/qcom/qdru1000.dtsi | 30 ++++++++++++++++++++++++++
> 1 file changed, 30 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/qdru1000.dtsi b/arch/arm64/boot/dts/qcom/qdru1000.dtsi
> index 3610f94bef35..39b9a00d3ad8 100644
> --- a/arch/arm64/boot/dts/qcom/qdru1000.dtsi
> +++ b/arch/arm64/boot/dts/qcom/qdru1000.dtsi
> @@ -235,6 +235,8 @@ uart7: serial@...000 {
> reg = <0x0 0x99c000 0x0 0x4000>;
> clock-names = "se";
> clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_uart7_default>;
> interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
> #address-cells = <1>;
> #size-cells = <0>;
> @@ -248,6 +250,34 @@ tcsr_mutex: hwlock@...0000 {
> #hwlock-cells = <1>;
> };
>
> + tlmm: pinctrl@...0000 {
> + compatible = "qcom,qdu1000-tlmm", "qcom,qru1000-tlmm";
> + reg = <0x0 0xf000000 0x0 0x1000000>;
> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + gpio-ranges = <&tlmm 0 0 151>;
> + wakeup-parent = <&pdc>;
> +
> + qup_uart7_default: qup-uart7-default {
Suffix "-state"
> + tx {
Suffix "-pins"
> + pins = "gpio134";
> + function = "qup0_se7_l2";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + rx {
Suffix "-pins"
> + pins = "gpio135";
> + function = "qup0_se7_l3";
> + drive-strength = <2>;
> + bias-disable;
> + };
> + };
> + };
> +
> pdc: interrupt-controller@...0000 {
> compatible = "qcom,pdc";
> reg = <0x0 0xb220000 0x0 0x30000>, <0x0 0x174000f0 0x0 0x64>;
Best regards,
Krzysztof
Powered by blists - more mailing lists