| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <6d58c08e-1537-f1ab-2883-baf869650ef2@linaro.org>
Date: Tue, 4 Oct 2022 09:04:15 +0200
From: Krzysztof Kozlowski <krzysztof.kozlowski@...aro.org>
To: Colin Foster <colin.foster@...advantage.com>,
linux-omap@...r.kernel.org, linux-kernel@...r.kernel.org,
devicetree@...r.kernel.org, linux-arm-kernel@...ts.infradead.org
Cc: Tony Lindgren <tony@...mide.com>,
Benoît Cousson <bcousson@...libre.com>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Rob Herring <robh+dt@...nel.org>, soc@...nel.org,
Olof Johansson <olof@...om.net>, Arnd Bergmann <arnd@...db.de>
Subject: Re: [RFC v1 1/1] arm: dts: omap4: pcm959: add initial support for
phytec pcm959
On 04/10/2022 04:40, Colin Foster wrote:
> The Phytec PCM-959 is a development platform for the Phytec PCM-049 SOM.
> Add initial functionality for the board. The verified interfaces and
> peripherals are listed below for the SOM (PCM-049) and the dev board
> (PCM-959)
>
> The omap2plus_defconfig was used for testing. Only the On-board LEDs
> required CONFIG_LEDS_PCA9532 addition.
>
> PCM-049:
> i2c1
> * EEPROM at 0x50
> * TMP102 (hwmon) at 0x4b
> twl6030
> GPMC
> * Ethernet
> * Flash
> Serial (ttyS2 console)
>
> PCM959:
> MMC1
> On-board LEDs (with CONFIG_LEDS_PCA9532)
>
> Signed-off-by: Colin Foster <colin.foster@...advantage.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/omap4-phytec-pcm-049.dtsi | 352 ++++++++++++++++++++
> arch/arm/boot/dts/omap4-phytec-pcm-959.dts | 130 ++++++++
> 3 files changed, 483 insertions(+)
> create mode 100644 arch/arm/boot/dts/omap4-phytec-pcm-049.dtsi
> create mode 100644 arch/arm/boot/dts/omap4-phytec-pcm-959.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 27eec8e670ec..ef225150c5d7 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -949,6 +949,7 @@ dtb-$(CONFIG_ARCH_OMAP4) += \
> omap4-panda.dtb \
> omap4-panda-a4.dtb \
> omap4-panda-es.dtb \
> + omap4-phytec-pcm-959.dtb \
> omap4-sdp.dtb \
> omap4-sdp-es23plus.dtb \
> omap4-var-dvk-om44.dtb \
> diff --git a/arch/arm/boot/dts/omap4-phytec-pcm-049.dtsi b/arch/arm/boot/dts/omap4-phytec-pcm-049.dtsi
> new file mode 100644
> index 000000000000..05b5cd581f15
> --- /dev/null
> +++ b/arch/arm/boot/dts/omap4-phytec-pcm-049.dtsi
> @@ -0,0 +1,352 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (C) 2022 Innovative Advantage, Inc.
> + */
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> + memory@...00000 {
> + device_type = "memory";
> + reg = <0x80000000 0x40000000>; /* 1 GB */
> + };
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + dsp_memory_region: dsp-memory@...00000 {
> + compatible = "shared-dma-pool";
> + reg = <0x98000000 0x800000>;
> + reusable;
> + status = "okay";
> + };
> +
> + ipu_memory_region: ipu-memory@...00000 {
> + compatible = "shared-dma-pool";
> + reg = <0x98800000 0x7000000>;
> + reusable;
> + status = "okay";
> + };
> + };
> +
> + chosen {
> + stdout-path = &uart3;
> + };
> +
> + leds: leds {
Does not look like you tested the DTS against bindings. Please run `make
dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
for instructions).
> + status = "okay";
By default it is okay. If you override, override by label.
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <
> + &led_gpio_pins
> + >;
> +
> + heartbeat {
led-heartbeat or led-0
> + label = "modul:red:status1";
> + gpios = <&gpio5 0x18 GPIO_ACTIVE_HIGH>; /* GPIO 152 */
> + linux,default-trigger = "heartbeat";
> + };
> +
> + mmc {
ditto
> + label = "modul:green:status2";
> + gpios = <&gpio5 0x19 GPIO_ACTIVE_HIGH>; /* GPIO 153 */
> + linux,default-trigger = "mmc0";
> + };
> + };
> +};
> +
> +&omap4_pmx_core {
> + i2c1_pins: pinmux_i2c1_pins {
No underscores in node names. Use hyphen/dash
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
> + OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
> + >;
> + };
> +
> + i2c3_pins: pinmux_i2c3_pins {
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
> + OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
> + >;
> + };
> +
> + i2c4_pins: pinmux_i2c4_pins {
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */
> + OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */
> + >;
> + };
> +
> + uart1_pins: pinmux_uart1_pins {
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE1) /* uart1_rx */
> + OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE1) /* uart1_tx */
> + >;
> + };
> +
> + led_gpio_pins: pinmux_leds_pins {
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x156, PIN_OUTPUT | MUX_MODE3) /* gpio_152 */
> + OMAP4_IOPAD(0x158, PIN_OUTPUT | MUX_MODE3) /* gpio_153 */
> + >;
> + };
> +
> + pinctrl_tempsense: pinmux_pinctrl_tempsense_pins{
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x154, PIN_INPUT_PULLUP | MUX_MODE3) /* gpio_151 */
> + >;
> + };
> +
> + gpmc_pins: gpmc_pins {
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x40, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad0 */
> + OMAP4_IOPAD(0x42, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad1 */
> + OMAP4_IOPAD(0x44, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad2 */
> + OMAP4_IOPAD(0x46, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad3 */
> + OMAP4_IOPAD(0x48, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad4 */
> + OMAP4_IOPAD(0x4a, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad5 */
> + OMAP4_IOPAD(0x4c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad6 */
> + OMAP4_IOPAD(0x4e, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad7 */
> + OMAP4_IOPAD(0x50, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad8 */
> + OMAP4_IOPAD(0x52, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad9 */
> + OMAP4_IOPAD(0x54, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad10 */
> + OMAP4_IOPAD(0x56, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad11 */
> + OMAP4_IOPAD(0x58, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad12 */
> + OMAP4_IOPAD(0x5a, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad13 */
> + OMAP4_IOPAD(0x5c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad14 */
> + OMAP4_IOPAD(0x5e, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad15 */
> +
> + OMAP4_IOPAD(0x60, PIN_OUTPUT | MUX_MODE0) /* gpmc_a16 */
> + OMAP4_IOPAD(0x62, PIN_OUTPUT | MUX_MODE0) /* gpmc_a17 */
> + OMAP4_IOPAD(0x64, PIN_OUTPUT | MUX_MODE0) /* gpmc_a18 */
> + OMAP4_IOPAD(0x66, PIN_OUTPUT | MUX_MODE0) /* gpmc_a19 */
> + OMAP4_IOPAD(0x68, PIN_OUTPUT | MUX_MODE0) /* gpmc_a20 */
> + OMAP4_IOPAD(0x6a, PIN_OUTPUT | MUX_MODE0) /* gpmc_a21 */
> + OMAP4_IOPAD(0x6c, PIN_OUTPUT | MUX_MODE0) /* gpmc_a22 */
> + OMAP4_IOPAD(0x6e, PIN_OUTPUT | MUX_MODE0) /* gpmc_a23 */
> +
> + OMAP4_IOPAD(0x82, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* gpmc_noe */
> + OMAP4_IOPAD(0x84, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* gpmc_nwe */
> +
> + OMAP4_IOPAD(0x7c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* gpmc_nwp */
> + OMAP4_IOPAD(0x80, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* gpmc_nadv_ale */
> + OMAP4_IOPAD(0x86, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* gpmc_nbe0_cle */
> + OMAP4_IOPAD(0x8a, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0 */
> + OMAP4_IOPAD(0x8c, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait1 */
> +
> + OMAP4_IOPAD(0x74, PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_ncs0 */
> + OMAP4_IOPAD(0x76, PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_ncs1 */
> + OMAP4_IOPAD(0x92, PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_ncs5 */
> + >;
> + };
> +
> + ethernet_pins: ethernet_pins {
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x114, PIN_INPUT | MUX_MODE3) /* gpio_121 */
> + >;
> + };
> +
> + tps62361_pins: pinmux_tps62361_pins {
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x19c, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpio_182 */
> + >;
> + };
> +
> + mmc1_pins: pinmux_mmc1_pins {
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x0e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */
> + OMAP4_IOPAD(0x0e4, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd */
> + OMAP4_IOPAD(0x0e6, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0 */
> + OMAP4_IOPAD(0x0e8, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */
> + OMAP4_IOPAD(0x0ea, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */
> + OMAP4_IOPAD(0x0ec, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */
> + >;
> + };
> +
> +};
> +
> +&omap4_pmx_wkup {
> + ethernet_wkgpio_pins: pinmux_ethernet_wkpins {
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x66, PIN_OUTPUT | MUX_MODE3)
> + >;
> + };
> +};
> +
> +&i2c1 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins>;
> +
> + clock-frequency = <400000>;
> +
> + twl: twl@48 {
Please put compatible first in list of properties (and follow same order
in "required"). It's the most important piece, so we want it to be the
first to see. It also follows the convention of DTS, where compatible is
expected to be first.
> + reg = <0x48>;
> + status = "okay";
No need
> + /* IRQ# = 7 */
> + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */
> + };
> +
> + core_vdd_reg: tps62361@60 {
Node names should be generic.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + compatible = "ti,tps62361";
> + reg = <0x60>;
> + status = "okay";
No need
> +
> + regulator-name = "tps62361-vout";
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-coupled-max-spread = <300000>;
> + regulator-max-step-microvolt = <100000>;
> + regulator-boot-on;
> + regulator-always-on;
> + ti,vsel0-gpio = <&gpio5 22 GPIO_ACTIVE_HIGH>;
> + ti,vsel0-state-high;
> + };
> +
> + temperature-sensor@4b {
> + compatible = "ti,tmp102";
> + reg = <0x4b>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_tempsense>;
> + interrupt-parent = <&gpio5>;
> + interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
> + #thermal-sensor-cells = <1>;
> + };
> +
> + eeprom@50 {
> + compatible = "atmel,24c32";
> + reg = <0x50>;
> + };
> +};
> +
> +#include "twl6030.dtsi"
> +#include "twl6030_omap4.dtsi"
> +
> +&i2c2 {
> + status = "disabled";
> +};
> +
> +&i2c3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c3_pins>;
> + status = "okay";
> +
> + clock-frequency = <100000>;
> +};
> +
> +&i2c4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c4_pins>;
> + status = "disabled";
> +
> + clock-frequency = <400000>;
> +};
> +
> +&vmmc {
> + ti,retain-on-reset;
> +};
> +
> +&mmc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc1_pins>;
> +
> + vmmc-supply = <&vmmc>;
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&mmc2 {
> + status = "disabled";
> +};
> +
> +&mmc3 {
> + status = "disabled";
> +};
> +
> +&mmc4 {
> + status = "disabled";
> +};
> +
> +&mmc5 {
> + status = "disabled";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart3_pins>;
> + status = "okay";
> +};
> +
> +&uart4 {
> + status = "disabled";
> +};
> +
> +&elm {
> + status = "okay";
> +};
> +
> +#include "omap-gpmc-smsc9221.dtsi"
> +
> +&gpmc {
> + ranges = <5 0 0x2c000000 0x01000000>,
> + <0 0 0x08000000 0x01000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <
> + &gpmc_pins
> + >;
> + status = "okay";
> +
> + nandflash: nand@0,0 {
> + compatible = "ti,omap2-nand";
> + reg = <0 0 4>;
> + interrupt-parent = <&gpmc>;
> + rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>;
> + nand-bus-width = <16>;
> + ti,nand-ecc-opt = "bch8";
> + ti,elm-id=<&elm>;
> + linux,mtd-name = "micron,nand";
> + gpmc,device-nand = "true";
> + gpmc,device-width = <1>;
> +
> + gpmc,sync-clk-ps = <0>;
> + gpmc,cs-on-ns = <0>;
> + gpmc,cs-rd-off-ns = <44>;
> + gpmc,cs-wr-off-ns = <44>;
> + gpmc,adv-rd-off-ns = <34>;
> + gpmc,adv-wr-off-ns = <44>;
> + gpmc,we-off-ns = <40>;
> + gpmc,oe-off-ns = <54>;
> + gpmc,access-ns = <64>;
> + gpmc,rd-cycle-ns = <82>;
> + gpmc,wr-cycle-ns = <82>;
> + gpmc,wr-access-ns = <40>;
> + gpmc,wr-data-mux-bus-ns = <0>;
> +
> + #address-cells = <1>;
> + #size-cells = <1>;
> + };
> +
> + ethernet@...c {
> + reg = <5 0 0xff>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <
> + ðernet_pins
> + ðernet_wkgpio_pins
> + >;
> +
> + /* Either GPIO 103 or GPIO 121. Use 121 to match the reference design */
> + interrupt-parent = <&gpio4>;
> + interrupts = <25 IRQ_TYPE_LEVEL_LOW>;
> + status = "okay";
Is it a new node or override?
> + };
> +};
> diff --git a/arch/arm/boot/dts/omap4-phytec-pcm-959.dts b/arch/arm/boot/dts/omap4-phytec-pcm-959.dts
> new file mode 100644
> index 000000000000..dca2b1dd4d51
> --- /dev/null
> +++ b/arch/arm/boot/dts/omap4-phytec-pcm-959.dts
> @@ -0,0 +1,130 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (C) 2022 Innovative Advantage, Inc.
> + */
> +/dts-v1/;
> +
> +#include <dt-bindings/leds/leds-pca9532.h>
> +#include "omap4460.dtsi"
> +#include "omap4-phytec-pcm-049.dtsi"
> +
> +/ {
> + model = "Phytec PCM-959 Eval Board";
> + compatible = "ti,omap4460", "ti,omap4430", "ti,omap4";
RFC or not, you need to:
1. Use dedicated board compatible.
2. Document the compatible in bindings.
> +};
> +
> +&omap4_pmx_core {
> + pinctrl-names = "default";
> + pinctrl-0 = <
> + &sr_wkup_pins
> + &fref_xtal_in_pins
> + &fref_clk3_out_pins
> + &gpio_wk7_pins
> + &fref_clk4_out_pins
> + &sys_pins
> + &tps62361_pins
> + >;
> +
> + status = "okay";
> +
> + uart3_pins: pinmux_uart3_pins {
No underscores in node names.
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x140, PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_cts */
> + OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE0) /* uart3_rts */
> + OMAP4_IOPAD(0x11c, PIN_INPUT | MUX_MODE0) /* uart3_rx */
> + OMAP4_IOPAD(0x11e, PIN_OUTPUT | MUX_MODE0) /* uart3_tx */
> + >;
> + };
> +
> + uart2_pins: pinmux_uart2_pins {
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x118, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts */
> + OMAP4_IOPAD(0x11a, PIN_OUTPUT | MUX_MODE0) /* uart2_rts */
> + OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_rx */
> + OMAP4_IOPAD(0x11e, PIN_OUTPUT | MUX_MODE0) /* uart2_tx */
> + >;
> + };
> +};
> +
> +&gpio1_target {
> + ti,no-reset-on-init;
> +};
> +
> +&omap4_pmx_wkup {
> + sr_wkup_pins: pinmux_sr_wkup_pins {
Eh...
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x4a, PIN_INPUT_PULLUP | MUX_MODE0) /* sr_scl */
> + OMAP4_IOPAD(0x4c, PIN_INPUT_PULLUP | MUX_MODE0) /* sr_sda */
> + >;
> + };
> +
> + fref_xtal_in_pins: pinmux_fref_xtal_in_pins {
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x4e, PIN_OUTPUT | MUX_MODE0) /* fref_xtal_in */
> + >;
> + };
> +
> + fref_clk3_out_pins: pinmux_fref_clk3_out_pins {
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x58, PIN_OUTPUT | MUX_MODE0) /* fref_clk3_out */
> + >;
> + };
> +
> + gpio_wk7_pins: pinmux_gpio_wk7_pins {
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x5a, PIN_INPUT | MUX_MODE3) /* fref_clk4_req */
> + >;
> + };
> +
> + fref_clk4_out_pins: pinmux_fref_clk4_out_pins {
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x5c, PIN_OUTPUT | MUX_MODE0) /* fref_clk4_out */
> + >;
> + };
> +
> + sys_pins: pinmux_sys_pins {
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x5e, PIN_INPUT | MUX_MODE0) /* sys_32k */
> + OMAP4_IOPAD(0x60, PIN_OUTPUT | MUX_MODE0) /* sys_nrespwron */
> + OMAP4_IOPAD(0x62, PIN_OUTPUT | MUX_MODE0) /* sys_nreswarm */
> + OMAP4_IOPAD(0x64, PIN_OUTPUT_PULLUP | MUX_MODE0) /* sys_pwr_req */
> + OMAP4_IOPAD(0x66, PIN_OUTPUT | MUX_MODE0) /* sys_pwron_reset_out */
> + OMAP4_IOPAD(0x68, PIN_OUTPUT | MUX_MODE0) /* sys_boot6 */
> + OMAP4_IOPAD(0x6a, PIN_OUTPUT | MUX_MODE0) /* sys_boot7 */
> + >;
> + };
> +};
> +
> +&i2c4 {
> + status = "okay";
> +
> + leddim: leddimmer@62 {
Just 'led@62'
> + compatible = "nxp,pca9533";
> + reg = <0x62>;
> +
> + led1 {
led-1
> + label = "board:red:free_use1";
> + linux,default-trigger = "none";
> + type = <PCA9532_TYPE_LED>;
> + };
> +
> + led2 {
led-2
> + label = "board:yellow:free_use2";
> + linux,default-trigger = "none";
> + type = <PCA9532_TYPE_LED>;
Best regards,
Krzysztof
Powered by blists - more mailing lists