| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20221017225429.mvbi4ktm6v45cex7@builder.lan>
Date: Mon, 17 Oct 2022 17:54:29 -0500
From: Bjorn Andersson <andersson@...nel.org>
To: Krzysztof Kozlowski <krzysztof.kozlowski@...aro.org>
Cc: Andy Gross <agross@...nel.org>,
Konrad Dybcio <konrad.dybcio@...ainline.org>,
Linus Walleij <linus.walleij@...aro.org>,
Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
linux-arm-msm@...r.kernel.org, linux-gpio@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
Rob Herring <robh@...nel.org>
Subject: Re: [PATCH v3 4/4] dt-bindings: pinctrl: qcom,msm8998: convert to
dtschema
On Thu, Oct 13, 2022 at 05:06:12PM -0400, Krzysztof Kozlowski wrote:
> Convert Qualcomm MSM8998 pin controller bindings to DT schema. Keep the
> parsing of pin configuration subnodes consistent with other Qualcomm
> schemas (children named with '-state' suffix, their children with
> '-pins').
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@...aro.org>
> Reviewed-by: Rob Herring <robh@...nel.org>
Reviewed-by: Bjorn Andersson <andersson@...nel.org>
Regards,
Bjorn
>
> ---
>
> Changes since v2:
> 1. Drop default:2 for drive strength.
> 2. Add Rb tag.
>
> Changes since v1:
> 1. Correct bindings description.
> ---
> .../bindings/pinctrl/qcom,msm8998-pinctrl.txt | 202 ------------------
> .../pinctrl/qcom,msm8998-pinctrl.yaml | 175 +++++++++++++++
> 2 files changed, 175 insertions(+), 202 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt
> create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.yaml
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt
> deleted file mode 100644
> index c4de930f2406..000000000000
> --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt
> +++ /dev/null
> @@ -1,202 +0,0 @@
> -Qualcomm MSM8998 TLMM block
> -
> -This binding describes the Top Level Mode Multiplexer block found in the
> -MSM8998 platform.
> -
> -- compatible:
> - Usage: required
> - Value type: <string>
> - Definition: must be "qcom,msm8998-pinctrl"
> -
> -- reg:
> - Usage: required
> - Value type: <prop-encoded-array>
> - Definition: the base address and size of the TLMM register space.
> -
> -- interrupts:
> - Usage: required
> - Value type: <prop-encoded-array>
> - Definition: should specify the TLMM summary IRQ.
> -
> -- interrupt-controller:
> - Usage: required
> - Value type: <none>
> - Definition: identifies this node as an interrupt controller
> -
> -- #interrupt-cells:
> - Usage: required
> - Value type: <u32>
> - Definition: must be 2. Specifying the pin number and flags, as defined
> - in <dt-bindings/interrupt-controller/irq.h>
> -
> -- gpio-controller:
> - Usage: required
> - Value type: <none>
> - Definition: identifies this node as a gpio controller
> -
> -- #gpio-cells:
> - Usage: required
> - Value type: <u32>
> - Definition: must be 2. Specifying the pin number and flags, as defined
> - in <dt-bindings/gpio/gpio.h>
> -
> -- gpio-ranges:
> - Usage: required
> - Definition: see ../gpio/gpio.txt
> -
> -- gpio-reserved-ranges:
> - Usage: optional
> - Definition: see ../gpio/gpio.txt
> -
> -Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
> -a general description of GPIO and interrupt bindings.
> -
> -Please refer to pinctrl-bindings.txt in this directory for details of the
> -common pinctrl bindings used by client devices, including the meaning of the
> -phrase "pin configuration node".
> -
> -The pin configuration nodes act as a container for an arbitrary number of
> -subnodes. Each of these subnodes represents some desired configuration for a
> -pin, a group, or a list of pins or groups. This configuration can include the
> -mux function to select on those pin(s)/group(s), and various pin configuration
> -parameters, such as pull-up, drive strength, etc.
> -
> -
> -PIN CONFIGURATION NODES:
> -
> -The name of each subnode is not important; all subnodes should be enumerated
> -and processed purely based on their content.
> -
> -Each subnode only affects those parameters that are explicitly listed. In
> -other words, a subnode that lists a mux function but no pin configuration
> -parameters implies no information about any pin configuration parameters.
> -Similarly, a pin subnode that describes a pullup parameter implies no
> -information about e.g. the mux function.
> -
> -
> -The following generic properties as defined in pinctrl-bindings.txt are valid
> -to specify in a pin configuration subnode:
> -
> -- pins:
> - Usage: required
> - Value type: <string-array>
> - Definition: List of gpio pins affected by the properties specified in
> - this subnode.
> -
> - Valid pins are:
> - gpio0-gpio149
> - Supports mux, bias and drive-strength
> -
> - sdc2_clk, sdc2_cmd, sdc2_data
> - Supports bias and drive-strength
> -
> - ufs_reset
> - Supports bias and drive-strength
> -
> -- function:
> - Usage: required
> - Value type: <string>
> - Definition: Specify the alternative function to be configured for the
> - specified pins. Functions are only valid for gpio pins.
> - Valid values are:
> -
> - gpio, adsp_ext, agera_pll, atest_char, atest_gpsadc0,
> - atest_gpsadc1, atest_tsens, atest_tsens2, atest_usb1,
> - atest_usb10, atest_usb11, atest_usb12, atest_usb13,
> - audio_ref, bimc_dte0, bimc_dte1, blsp10_spi, blsp10_spi_a,
> - blsp10_spi_b, blsp11_i2c, blsp1_spi, blsp1_spi_a,
> - blsp1_spi_b, blsp2_spi, blsp9_spi, blsp_i2c1, blsp_i2c2,
> - blsp_i2c3, blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7,
> - blsp_i2c8, blsp_i2c9, blsp_i2c10, blsp_i2c11, blsp_i2c12,
> - blsp_spi1, blsp_spi2, blsp_spi3, blsp_spi4, blsp_spi5,
> - blsp_spi6, blsp_spi7, blsp_spi8, blsp_spi9, blsp_spi10,
> - blsp_spi11, blsp_spi12, blsp_uart1_a, blsp_uart1_b,
> - blsp_uart2_a, blsp_uart2_b, blsp_uart3_a, blsp_uart3_b,
> - blsp_uart7_a, blsp_uart7_b, blsp_uart8, blsp_uart8_a,
> - blsp_uart8_b, blsp_uart9_a, blsp_uart9_b, blsp_uim1_a,
> - blsp_uim1_b, blsp_uim2_a, blsp_uim2_b, blsp_uim3_a,
> - blsp_uim3_b, blsp_uim7_a, blsp_uim7_b, blsp_uim8_a,
> - blsp_uim8_b, blsp_uim9_a, blsp_uim9_b, bt_reset,
> - btfm_slimbus, cam_mclk, cci_async, cci_i2c, cci_timer0,
> - cci_timer1, cci_timer2, cci_timer3, cci_timer4, cri_trng,
> - cri_trng0, cri_trng1, dbg_out, ddr_bist, edp_hot, edp_lcd,
> - gcc_gp1_a, gcc_gp1_b, gcc_gp2_a, gcc_gp2_b, gcc_gp3_a,
> - gcc_gp3_b, hdmi_cec, hdmi_ddc, hdmi_hot, hdmi_rcv,
> - isense_dbg, jitter_bist, ldo_en, ldo_update, lpass_slimbus,
> - m_voc, mdp_vsync, mdp_vsync0, mdp_vsync1, mdp_vsync2,
> - mdp_vsync3, mdp_vsync_a, mdp_vsync_b, modem_tsync, mss_lte,
> - nav_dr, nav_pps, pa_indicator, pci_e0, phase_flag,
> - pll_bypassnl, pll_reset, pri_mi2s, pri_mi2s_ws, prng_rosc,
> - pwr_crypto, pwr_modem, pwr_nav, qdss_cti0_a, qdss_cti0_b,
> - qdss_cti1_a, qdss_cti1_b, qdss, qlink_enable,
> - qlink_request, qua_mi2s, sd_card, sd_write, sdc40, sdc41,
> - sdc42, sdc43, sdc4_clk, sdc4_cmd, sec_mi2s, sp_cmu,
> - spkr_i2s, ssbi1, ssc_irq, ter_mi2s, tgu_ch0, tgu_ch1,
> - tsense_pwm1, tsense_pwm2, tsif0, tsif1,
> - uim1_clk, uim1_data, uim1_present,
> - uim1_reset, uim2_clk, uim2_data, uim2_present, uim2_reset,
> - uim_batt, usb_phy, vfr_1, vsense_clkout, vsense_data0,
> - vsense_data1, vsense_mode, wlan1_adc0, wlan1_adc1,
> - wlan2_adc0, wlan2_adc1,
> -
> -- bias-disable:
> - Usage: optional
> - Value type: <none>
> - Definition: The specified pins should be configured as no pull.
> -
> -- bias-pull-down:
> - Usage: optional
> - Value type: <none>
> - Definition: The specified pins should be configured as pull down.
> -
> -- bias-pull-up:
> - Usage: optional
> - Value type: <none>
> - Definition: The specified pins should be configured as pull up.
> -
> -- output-high:
> - Usage: optional
> - Value type: <none>
> - Definition: The specified pins are configured in output mode, driven
> - high.
> - Not valid for sdc pins.
> -
> -- output-low:
> - Usage: optional
> - Value type: <none>
> - Definition: The specified pins are configured in output mode, driven
> - low.
> - Not valid for sdc pins.
> -
> -- drive-strength:
> - Usage: optional
> - Value type: <u32>
> - Definition: Selects the drive strength for the specified pins, in mA.
> - Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
> -
> -Example:
> -
> - tlmm: pinctrl@...00000 {
> - compatible = "qcom,msm8998-pinctrl";
> - reg = <0x03400000 0xc00000>;
> - interrupts = <0 208 0>;
> - gpio-controller;
> - #gpio-cells = <2>;
> - gpio-ranges = <&tlmm 0 0 175>;
> - gpio-reserved-ranges = <0 4>, <81 4>;
> - interrupt-controller;
> - #interrupt-cells = <2>;
> -
> - uart_console_active: uart_console_active {
> - mux {
> - pins = "gpio4", "gpio5";
> - function = "blsp_uart8_a";
> - };
> -
> - config {
> - pins = "gpio4", "gpio5";
> - drive-strength = <2>;
> - bias-disable;
> - };
> - };
> - };
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.yaml
> new file mode 100644
> index 000000000000..180c13c4ea69
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.yaml
> @@ -0,0 +1,175 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/qcom,msm8998-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm MSM8998 TLMM pin controller
> +
> +maintainers:
> + - Bjorn Andersson <andersson@...nel.org>
> + - Krzysztof Kozlowski <krzysztof.kozlowski@...aro.org>
> +
> +description:
> + Top Level Mode Multiplexer pin controller in Qualcomm MSM8998 SoC.
> +
> +properties:
> + compatible:
> + const: qcom,msm8998-pinctrl
> +
> + reg:
> + maxItems: 1
> +
> + interrupts: true
> + interrupt-controller: true
> + "#interrupt-cells": true
> + gpio-controller: true
> + "#gpio-cells": true
> + gpio-ranges: true
> + wakeup-parent: true
> +
> + gpio-reserved-ranges:
> + minItems: 1
> + maxItems: 75
> +
> + gpio-line-names:
> + maxItems: 150
> +
> +patternProperties:
> + "-state$":
> + oneOf:
> + - $ref: "#/$defs/qcom-msm8998-tlmm-state"
> + - patternProperties:
> + "-pins$":
> + $ref: "#/$defs/qcom-msm8998-tlmm-state"
> + additionalProperties: false
> +
> +$defs:
> + qcom-msm8998-tlmm-state:
> + type: object
> + description:
> + Pinctrl node's client devices use subnodes for desired pin configuration.
> + Client device subnodes use below standard properties.
> + $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
> +
> + properties:
> + pins:
> + description:
> + List of gpio pins affected by the properties specified in this
> + subnode.
> + items:
> + oneOf:
> + - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-4][0-9])$"
> + - enum: [ sdc2_clk, sdc2_cmd, sdc2_data, ufs_reset ]
> + minItems: 1
> + maxItems: 36
> +
> + function:
> + description:
> + Specify the alternative function to be configured for the specified
> + pins.
> +
> + enum: [ gpio, adsp_ext, agera_pll, atest_char, atest_gpsadc0,
> + atest_gpsadc1, atest_tsens, atest_tsens2, atest_usb1,
> + atest_usb10, atest_usb11, atest_usb12, atest_usb13, audio_ref,
> + bimc_dte0, bimc_dte1, blsp10_spi, blsp10_spi_a, blsp10_spi_b,
> + blsp11_i2c, blsp1_spi, blsp1_spi_a, blsp1_spi_b, blsp2_spi,
> + blsp9_spi, blsp_i2c1, blsp_i2c2, blsp_i2c3, blsp_i2c4,
> + blsp_i2c5, blsp_i2c6, blsp_i2c7, blsp_i2c8, blsp_i2c9,
> + blsp_i2c10, blsp_i2c11, blsp_i2c12, blsp_spi1, blsp_spi2,
> + blsp_spi3, blsp_spi4, blsp_spi5, blsp_spi6, blsp_spi7,
> + blsp_spi8, blsp_spi9, blsp_spi10, blsp_spi11, blsp_spi12,
> + blsp_uart1_a, blsp_uart1_b, blsp_uart2_a, blsp_uart2_b,
> + blsp_uart3_a, blsp_uart3_b, blsp_uart7_a, blsp_uart7_b,
> + blsp_uart8, blsp_uart8_a, blsp_uart8_b, blsp_uart9_a,
> + blsp_uart9_b, blsp_uim1_a, blsp_uim1_b, blsp_uim2_a,
> + blsp_uim2_b, blsp_uim3_a, blsp_uim3_b, blsp_uim7_a,
> + blsp_uim7_b, blsp_uim8_a, blsp_uim8_b, blsp_uim9_a,
> + blsp_uim9_b, bt_reset, btfm_slimbus, cam_mclk, cci_async,
> + cci_i2c, cci_timer0, cci_timer1, cci_timer2, cci_timer3,
> + cci_timer4, cri_trng, cri_trng0, cri_trng1, dbg_out, ddr_bist,
> + edp_hot, edp_lcd, gcc_gp1_a, gcc_gp1_b, gcc_gp2_a, gcc_gp2_b,
> + gcc_gp3_a, gcc_gp3_b, hdmi_cec, hdmi_ddc, hdmi_hot, hdmi_rcv,
> + isense_dbg, jitter_bist, ldo_en, ldo_update, lpass_slimbus,
> + m_voc, mdp_vsync, mdp_vsync0, mdp_vsync1, mdp_vsync2,
> + mdp_vsync3, mdp_vsync_a, mdp_vsync_b, modem_tsync, mss_lte,
> + nav_dr, nav_pps, pa_indicator, pci_e0, phase_flag,
> + pll_bypassnl, pll_reset, pri_mi2s, pri_mi2s_ws, prng_rosc,
> + pwr_crypto, pwr_modem, pwr_nav, qdss_cti0_a, qdss_cti0_b,
> + qdss_cti1_a, qdss_cti1_b, qdss, qlink_enable, qlink_request,
> + qua_mi2s, sd_card, sd_write, sdc40, sdc41, sdc42, sdc43,
> + sdc4_clk, sdc4_cmd, sec_mi2s, sp_cmu, spkr_i2s, ssbi1, ssc_irq,
> + ter_mi2s, tgu_ch0, tgu_ch1, tsense_pwm1, tsense_pwm2, tsif0,
> + tsif1, uim1_clk, uim1_data, uim1_present, uim1_reset, uim2_clk,
> + uim2_data, uim2_present, uim2_reset, uim_batt, usb_phy, vfr_1,
> + vsense_clkout, vsense_data0, vsense_data1, vsense_mode,
> + wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1 ]
> +
> + drive-strength:
> + enum: [2, 4, 6, 8, 10, 12, 14, 16]
> + description:
> + Selects the drive strength for the specified pins, in mA.
> +
> + bias-pull-down: true
> + bias-pull-up: true
> + bias-disable: true
> + input-enable: true
> + output-high: true
> + output-low: true
> +
> + required:
> + - pins
> +
> + additionalProperties: false
> +
> +allOf:
> + - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
> +
> +required:
> + - compatible
> + - reg
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> + tlmm: pinctrl@...0000 {
> + compatible = "qcom,msm8998-pinctrl";
> + reg = <0x03400000 0xc00000>;
> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> + gpio-ranges = <&tlmm 0 0 150>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + gpio-reserved-ranges = <0 4>, <81 4>;
> +
> + sdc2-off-state {
> + clk-pins {
> + pins = "sdc2_clk";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + cmd-pins {
> + pins = "sdc2_cmd";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + data-pins {
> + pins = "sdc2_data";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> + };
> +
> + sdc2-cd-state {
> + pins = "gpio95";
> + function = "gpio";
> + bias-pull-up;
> + drive-strength = <2>;
> + };
> + };
> --
> 2.34.1
>
Powered by blists - more mailing lists