| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20221019022450.16851-6-larry.lai@yunjingtech.com>
Date: Wed, 19 Oct 2022 10:24:50 +0800
From: chengwei <foxfly.lai.tw@...il.com>
To: lee@...nel.org, broonie@...nel.org, rafael@...nel.org,
mika.westerberg@...ux.intel.com, andriy.shevchenko@...ux.intel.com,
linus.walleij@...aro.org, brgl@...ev.pl
Cc: linux-kernel@...r.kernel.org, gregkh@...uxfoundation.org,
lenb@...nel.org, linux-acpi@...r.kernel.org,
linux-gpio@...r.kernel.org, GaryWang@...on.com.tw,
musa.lin@...jingtech.com, jack.chang@...jingtech.com,
chengwei <larry.lai@...jingtech.com>,
Javier Arteaga <javier@...tex.com>,
Nicola Lunghi <nicola.lunghi@...tex.com>
Subject: [PATCH 5/5] pinctrl: Add support pin control for UP board CPLD/FPGA
The UP Squared board <http://www.upboard.com> implements certain
features (pin control) through an on-board FPGA.
Signed-off-by: Javier Arteaga <javier@...tex.com>
[merge various fixes]
Signed-off-by: Nicola Lunghi <nicola.lunghi@...tex.com>
Signed-off-by: chengwei <larry.lai@...jingtech.com>
---
drivers/pinctrl/Kconfig | 15 +
drivers/pinctrl/Makefile | 1 +
drivers/pinctrl/pinctrl-upboard.c | 1003 +++++++++++++++++++++++++++++
3 files changed, 1019 insertions(+)
create mode 100644 drivers/pinctrl/pinctrl-upboard.c
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index 1cf74b0c42e5..5d719eadecdb 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -483,6 +483,21 @@ config PINCTRL_THUNDERBAY
rate control and direction control. This module will be
called as pinctrl-thunderbay.
+config PINCTRL_UPBOARD
+ tristate "UP board FPGA pin controller"
+ depends on ACPI
+ depends on MFD_UPBOARD_FPGA
+ depends on X86
+ select GENERIC_PINCONF
+ select PINMUX
+ select PINCONF
+ help
+ Pin controller for the FPGA GPIO lines on UP boards. Due to the
+ hardware layout, these are meant to be controlled in tandem with their
+ corresponding Intel SoC GPIOs.
+ To compile this driver as a module, choose M here: the module
+ will be called pinctrl-upboard.
+
config PINCTRL_ZYNQ
bool "Pinctrl driver for Xilinx Zynq"
depends on ARCH_ZYNQ
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index e76f5cdc64b0..c366706d36e7 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -48,6 +48,7 @@ obj-$(CONFIG_PINCTRL_STMFX) += pinctrl-stmfx.o
obj-$(CONFIG_PINCTRL_SX150X) += pinctrl-sx150x.o
obj-$(CONFIG_PINCTRL_TB10X) += pinctrl-tb10x.o
obj-$(CONFIG_PINCTRL_THUNDERBAY) += pinctrl-thunderbay.o
+obj-$(CONFIG_PINCTRL_UPBOARD) += pinctrl-upboard.o
obj-$(CONFIG_PINCTRL_ZYNQMP) += pinctrl-zynqmp.o
obj-$(CONFIG_PINCTRL_ZYNQ) += pinctrl-zynq.o
diff --git a/drivers/pinctrl/pinctrl-upboard.c b/drivers/pinctrl/pinctrl-upboard.c
new file mode 100644
index 000000000000..39cd45357f6b
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-upboard.c
@@ -0,0 +1,1003 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * UP Board FPGA-based pin controller driver
+ *
+ * Copyright (c) 2017, Emutex Ltd. All rights reserved.
+ *
+ * Authors: Javier Arteaga <javier@...tex.com>
+ * Dan O'Donovan <dan@...tex.com>
+ * Nicola Lunghi <nicolal@...tex.com>
+ */
+
+#include <linux/acpi.h>
+#include <linux/dmi.h>
+#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
+#include <linux/gpio/driver.h>
+#include <linux/kernel.h>
+#include <linux/mfd/upboard-fpga.h>
+#include <linux/module.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/string.h>
+
+#include "core.h"
+
+struct upboard_pin {
+ struct regmap_field *funcbit;
+ struct regmap_field *enbit;
+ struct regmap_field *dirbit;
+};
+
+struct upboard_bios {
+ const struct reg_sequence *patches;
+ size_t npatches;
+};
+
+struct upboard_pinctrl {
+ struct device *dev;
+ struct pinctrl_dev *pctldev;
+ struct regmap *regmap;
+ struct gpio_chip chip;
+ const unsigned int *rpi_mapping;
+};
+
+enum upboard_func0_fpgabit {
+ UPFPGA_I2C0_EN = 8,
+ UPFPGA_I2C1_EN = 9,
+ UPFPGA_CEC0_EN = 12,
+ UPFPGA_ADC0_EN = 14,
+};
+
+static const struct reg_field upboard_i2c0_reg =
+ REG_FIELD(UPFPGA_REG_FUNC_EN0, UPFPGA_I2C0_EN, UPFPGA_I2C0_EN);
+
+static const struct reg_field upboard_i2c1_reg =
+ REG_FIELD(UPFPGA_REG_FUNC_EN0, UPFPGA_I2C1_EN, UPFPGA_I2C1_EN);
+
+static const struct reg_field upboard_adc0_reg =
+ REG_FIELD(UPFPGA_REG_FUNC_EN0, UPFPGA_ADC0_EN, UPFPGA_ADC0_EN);
+
+#define UPBOARD_BIT_TO_PIN(r, bit) \
+ ((r) * UPFPGA_REGISTER_SIZE + (bit))
+
+/*
+ * UP board data
+ */
+
+#define UPBOARD_UP_BIT_TO_PIN(r, id) (UPBOARD_BIT_TO_PIN(r, UPFPGA_UP_##id))
+
+#define UPBOARD_UP_PIN_ANON(r, bit) \
+ { \
+ .number = UPBOARD_BIT_TO_PIN(r, bit), \
+ }
+
+#define UPBOARD_UP_PIN_NAME(r, id) \
+ { \
+ .number = UPBOARD_UP_BIT_TO_PIN(r, id), \
+ .name = #id, \
+ }
+
+#define UPBOARD_UP_PIN_FUNC(r, id, data) \
+ { \
+ .number = UPBOARD_UP_BIT_TO_PIN(r, id), \
+ .name = #id, \
+ .drv_data = (void *)(data), \
+ }
+
+enum upboard_up_reg1_fpgabit {
+ UPFPGA_UP_I2C1_SDA,
+ UPFPGA_UP_I2C1_SCL,
+ UPFPGA_UP_ADC0,
+ UPFPGA_UP_GPIO17,
+ UPFPGA_UP_GPIO27,
+ UPFPGA_UP_GPIO22,
+ UPFPGA_UP_SPI_MOSI,
+ UPFPGA_UP_SPI_MISO,
+ UPFPGA_UP_SPI_CLK,
+ UPFPGA_UP_I2C0_SDA,
+ UPFPGA_UP_GPIO5,
+ UPFPGA_UP_GPIO6,
+ UPFPGA_UP_PWM1,
+ UPFPGA_UP_I2S_FRM,
+ UPFPGA_UP_GPIO26,
+ UPFPGA_UP_UART1_TX,
+};
+
+enum upboard_up_reg2_fpgabit {
+ UPFPGA_UP_UART1_RX,
+ UPFPGA_UP_I2S_CLK,
+ UPFPGA_UP_GPIO23,
+ UPFPGA_UP_GPIO24,
+ UPFPGA_UP_GPIO25,
+ UPFPGA_UP_SPI_CS0,
+ UPFPGA_UP_SPI_CS1,
+ UPFPGA_UP_I2C0_SCL,
+ UPFPGA_UP_PWM0,
+ UPFPGA_UP_GPIO16,
+ UPFPGA_UP_I2S_DIN,
+ UPFPGA_UP_I2S_DOUT,
+};
+
+static struct pinctrl_pin_desc upboard_up_pins[] = {
+ UPBOARD_UP_PIN_FUNC(0, I2C1_SDA, &upboard_i2c1_reg),
+ UPBOARD_UP_PIN_FUNC(0, I2C1_SCL, &upboard_i2c1_reg),
+ UPBOARD_UP_PIN_FUNC(0, ADC0, &upboard_adc0_reg),
+ UPBOARD_UP_PIN_NAME(0, GPIO17),
+ UPBOARD_UP_PIN_NAME(0, GPIO27),
+ UPBOARD_UP_PIN_NAME(0, GPIO22),
+ UPBOARD_UP_PIN_NAME(0, SPI_MOSI),
+ UPBOARD_UP_PIN_NAME(0, SPI_MISO),
+ UPBOARD_UP_PIN_NAME(0, SPI_CLK),
+ UPBOARD_UP_PIN_FUNC(0, I2C0_SDA, &upboard_i2c0_reg),
+ UPBOARD_UP_PIN_NAME(0, GPIO5),
+ UPBOARD_UP_PIN_NAME(0, GPIO6),
+ UPBOARD_UP_PIN_NAME(0, PWM1),
+ UPBOARD_UP_PIN_NAME(0, I2S_FRM),
+ UPBOARD_UP_PIN_NAME(0, GPIO26),
+ UPBOARD_UP_PIN_NAME(0, UART1_TX),
+ /* register 1 */
+ UPBOARD_UP_PIN_NAME(1, UART1_RX),
+ UPBOARD_UP_PIN_NAME(1, I2S_CLK),
+ UPBOARD_UP_PIN_NAME(1, GPIO23),
+ UPBOARD_UP_PIN_NAME(1, GPIO24),
+ UPBOARD_UP_PIN_NAME(1, GPIO25),
+ UPBOARD_UP_PIN_NAME(1, SPI_CS0),
+ UPBOARD_UP_PIN_NAME(1, SPI_CS1),
+ UPBOARD_UP_PIN_FUNC(1, I2C0_SCL, &upboard_i2c0_reg),
+ UPBOARD_UP_PIN_NAME(1, PWM0),
+ UPBOARD_UP_PIN_NAME(1, GPIO16),
+ UPBOARD_UP_PIN_NAME(1, I2S_DIN),
+ UPBOARD_UP_PIN_NAME(1, I2S_DOUT),
+};
+
+static const unsigned int upboard_up_rpi_mapping[] = {
+ UPBOARD_UP_BIT_TO_PIN(0, I2C0_SDA),
+ UPBOARD_UP_BIT_TO_PIN(1, I2C0_SCL),
+ UPBOARD_UP_BIT_TO_PIN(0, I2C1_SDA),
+ UPBOARD_UP_BIT_TO_PIN(0, I2C1_SCL),
+ UPBOARD_UP_BIT_TO_PIN(0, ADC0),
+ UPBOARD_UP_BIT_TO_PIN(0, GPIO5),
+ UPBOARD_UP_BIT_TO_PIN(0, GPIO6),
+ UPBOARD_UP_BIT_TO_PIN(1, SPI_CS1),
+ UPBOARD_UP_BIT_TO_PIN(1, SPI_CS0),
+ UPBOARD_UP_BIT_TO_PIN(0, SPI_MISO),
+ UPBOARD_UP_BIT_TO_PIN(0, SPI_MOSI),
+ UPBOARD_UP_BIT_TO_PIN(0, SPI_CLK),
+ UPBOARD_UP_BIT_TO_PIN(1, PWM0),
+ UPBOARD_UP_BIT_TO_PIN(0, PWM1),
+ UPBOARD_UP_BIT_TO_PIN(0, UART1_TX),
+ UPBOARD_UP_BIT_TO_PIN(1, UART1_RX),
+ UPBOARD_UP_BIT_TO_PIN(1, GPIO16),
+ UPBOARD_UP_BIT_TO_PIN(0, GPIO17),
+ UPBOARD_UP_BIT_TO_PIN(1, I2S_CLK),
+ UPBOARD_UP_BIT_TO_PIN(0, I2S_FRM),
+ UPBOARD_UP_BIT_TO_PIN(1, I2S_DIN),
+ UPBOARD_UP_BIT_TO_PIN(1, I2S_DOUT),
+ UPBOARD_UP_BIT_TO_PIN(0, GPIO22),
+ UPBOARD_UP_BIT_TO_PIN(1, GPIO23),
+ UPBOARD_UP_BIT_TO_PIN(1, GPIO24),
+ UPBOARD_UP_BIT_TO_PIN(1, GPIO25),
+ UPBOARD_UP_BIT_TO_PIN(0, GPIO26),
+ UPBOARD_UP_BIT_TO_PIN(0, GPIO27),
+};
+
+/*
+ * Init patches applied to the registers until the BIOS sets proper defaults
+ */
+static const struct reg_sequence upboard_up_reg_patches[] __initconst = {
+ { UPFPGA_REG_FUNC_EN0,
+ // enable I2C voltage-level shifters
+ BIT(UPFPGA_I2C0_EN) |
+ BIT(UPFPGA_I2C1_EN) |
+ // enable adc
+ BIT(UPFPGA_ADC0_EN)
+ },
+ /* HAT function pins initially set as inputs */
+ { UPFPGA_REG_GPIO_DIR0,
+ BIT(UPFPGA_UP_I2C1_SDA) |
+ BIT(UPFPGA_UP_I2C1_SCL) |
+ BIT(UPFPGA_UP_ADC0) |
+ BIT(UPFPGA_UP_GPIO27) |
+ BIT(UPFPGA_UP_GPIO22) |
+ BIT(UPFPGA_UP_SPI_MISO) |
+ BIT(UPFPGA_UP_I2C0_SDA) |
+ BIT(UPFPGA_UP_GPIO5) |
+ BIT(UPFPGA_UP_GPIO6) |
+ BIT(UPFPGA_UP_GPIO26)
+ },
+ { UPFPGA_REG_GPIO_DIR1,
+ BIT(UPFPGA_UP_UART1_RX) |
+ BIT(UPFPGA_UP_GPIO23) |
+ BIT(UPFPGA_UP_GPIO24) |
+ BIT(UPFPGA_UP_GPIO25) |
+ BIT(UPFPGA_UP_I2C0_SCL) |
+ BIT(UPFPGA_UP_GPIO16) |
+ BIT(UPFPGA_UP_I2S_DIN)
+ },
+};
+
+static const struct upboard_bios upboard_up_bios_info_dvt __initconst = {
+ .patches = upboard_up_reg_patches,
+ .npatches = ARRAY_SIZE(upboard_up_reg_patches),
+};
+
+/*
+ * UP^2 board data
+ */
+
+#define UPBOARD_UP2_BIT_TO_PIN(r, id) (UPBOARD_BIT_TO_PIN(r, UPFPGA_UP2_##id))
+
+#define UPBOARD_UP2_PIN_ANON(r, bit) \
+ { \
+ .number = UPBOARD_BIT_TO_PIN(r, bit), \
+ }
+
+#define UPBOARD_UP2_PIN_NAME(r, id) \
+ { \
+ .number = UPBOARD_UP2_BIT_TO_PIN(r, id), \
+ .name = #id, \
+ }
+
+#define UPBOARD_UP2_PIN_FUNC(r, id, data) \
+ { \
+ .number = UPBOARD_UP2_BIT_TO_PIN(r, id), \
+ .name = #id, \
+ .drv_data = (void *)(data), \
+ }
+
+enum upboard_up2_reg0_fpgabit {
+ UPFPGA_UP2_UART1_TXD,
+ UPFPGA_UP2_UART1_RXD,
+ UPFPGA_UP2_UART1_RTS,
+ UPFPGA_UP2_UART1_CTS,
+ UPFPGA_UP2_GPIO3,
+ UPFPGA_UP2_GPIO5,
+ UPFPGA_UP2_GPIO6,
+ UPFPGA_UP2_GPIO11,
+ UPFPGA_UP2_EXHAT_LVDS1n,
+ UPFPGA_UP2_EXHAT_LVDS1p,
+ UPFPGA_UP2_SPI2_TXD,
+ UPFPGA_UP2_SPI2_RXD,
+ UPFPGA_UP2_SPI2_FS1,
+ UPFPGA_UP2_SPI2_FS0,
+ UPFPGA_UP2_SPI2_CLK,
+ UPFPGA_UP2_SPI1_TXD,
+};
+
+enum upboard_up2_reg1_fpgabit {
+ UPFPGA_UP2_SPI1_RXD,
+ UPFPGA_UP2_SPI1_FS1,
+ UPFPGA_UP2_SPI1_FS0,
+ UPFPGA_UP2_SPI1_CLK,
+ UPFPGA_UP2_BIT20,
+ UPFPGA_UP2_BIT21,
+ UPFPGA_UP2_BIT22,
+ UPFPGA_UP2_BIT23,
+ UPFPGA_UP2_PWM1,
+ UPFPGA_UP2_PWM0,
+ UPFPGA_UP2_EXHAT_LVDS0n,
+ UPFPGA_UP2_EXHAT_LVDS0p,
+ UPFPGA_UP2_I2C0_SCL,
+ UPFPGA_UP2_I2C0_SDA,
+ UPFPGA_UP2_I2C1_SCL,
+ UPFPGA_UP2_I2C1_SDA,
+};
+
+enum upboard_up2_reg2_fpgabit {
+ UPFPGA_UP2_EXHAT_LVDS3n,
+ UPFPGA_UP2_EXHAT_LVDS3p,
+ UPFPGA_UP2_EXHAT_LVDS4n,
+ UPFPGA_UP2_EXHAT_LVDS4p,
+ UPFPGA_UP2_EXHAT_LVDS5n,
+ UPFPGA_UP2_EXHAT_LVDS5p,
+ UPFPGA_UP2_I2S_SDO,
+ UPFPGA_UP2_I2S_SDI,
+ UPFPGA_UP2_I2S_WS_SYNC,
+ UPFPGA_UP2_I2S_BCLK,
+ UPFPGA_UP2_EXHAT_LVDS6n,
+ UPFPGA_UP2_EXHAT_LVDS6p,
+ UPFPGA_UP2_EXHAT_LVDS7n,
+ UPFPGA_UP2_EXHAT_LVDS7p,
+ UPFPGA_UP2_EXHAT_LVDS2n,
+ UPFPGA_UP2_EXHAT_LVDS2p,
+};
+
+static struct pinctrl_pin_desc upboard_up2_pins[] = {
+ UPBOARD_UP2_PIN_NAME(0, UART1_TXD),
+ UPBOARD_UP2_PIN_NAME(0, UART1_RXD),
+ UPBOARD_UP2_PIN_NAME(0, UART1_RTS),
+ UPBOARD_UP2_PIN_NAME(0, UART1_CTS),
+ UPBOARD_UP2_PIN_NAME(0, GPIO3),
+ UPBOARD_UP2_PIN_NAME(0, GPIO5),
+ UPBOARD_UP2_PIN_NAME(0, GPIO6),
+ UPBOARD_UP2_PIN_NAME(0, GPIO11),
+ UPBOARD_UP2_PIN_NAME(0, EXHAT_LVDS1n),
+ UPBOARD_UP2_PIN_NAME(0, EXHAT_LVDS1p),
+ UPBOARD_UP2_PIN_NAME(0, SPI2_TXD),
+ UPBOARD_UP2_PIN_NAME(0, SPI2_RXD),
+ UPBOARD_UP2_PIN_NAME(0, SPI2_FS1),
+ UPBOARD_UP2_PIN_NAME(0, SPI2_FS0),
+ UPBOARD_UP2_PIN_NAME(0, SPI2_CLK),
+ UPBOARD_UP2_PIN_NAME(0, SPI1_TXD),
+ UPBOARD_UP2_PIN_NAME(1, SPI1_RXD),
+ UPBOARD_UP2_PIN_NAME(1, SPI1_FS1),
+ UPBOARD_UP2_PIN_NAME(1, SPI1_FS0),
+ UPBOARD_UP2_PIN_NAME(1, SPI1_CLK),
+ UPBOARD_UP2_PIN_ANON(1, 4),
+ UPBOARD_UP2_PIN_ANON(1, 5),
+ UPBOARD_UP2_PIN_ANON(1, 6),
+ UPBOARD_UP2_PIN_ANON(1, 7),
+ UPBOARD_UP2_PIN_NAME(1, PWM1),
+ UPBOARD_UP2_PIN_NAME(1, PWM0),
+ UPBOARD_UP2_PIN_NAME(1, EXHAT_LVDS0n),
+ UPBOARD_UP2_PIN_NAME(1, EXHAT_LVDS0p),
+ UPBOARD_UP2_PIN_FUNC(1, I2C0_SCL, &upboard_i2c0_reg),
+ UPBOARD_UP2_PIN_FUNC(1, I2C0_SDA, &upboard_i2c0_reg),
+ UPBOARD_UP2_PIN_FUNC(1, I2C1_SCL, &upboard_i2c1_reg),
+ UPBOARD_UP2_PIN_FUNC(1, I2C1_SDA, &upboard_i2c1_reg),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS3n),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS3p),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS4n),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS4p),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS5n),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS5p),
+ UPBOARD_UP2_PIN_NAME(2, I2S_SDO),
+ UPBOARD_UP2_PIN_NAME(2, I2S_SDI),
+ UPBOARD_UP2_PIN_NAME(2, I2S_WS_SYNC),
+ UPBOARD_UP2_PIN_NAME(2, I2S_BCLK),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS6n),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS6p),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS7n),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS7p),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS2n),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS2p),
+};
+
+static const unsigned int upboard_up2_rpi_mapping[] = {
+ UPBOARD_UP2_BIT_TO_PIN(1, I2C0_SDA),
+ UPBOARD_UP2_BIT_TO_PIN(1, I2C0_SCL),
+ UPBOARD_UP2_BIT_TO_PIN(1, I2C1_SDA),
+ UPBOARD_UP2_BIT_TO_PIN(1, I2C1_SCL),
+ UPBOARD_UP2_BIT_TO_PIN(0, GPIO3),
+ UPBOARD_UP2_BIT_TO_PIN(0, GPIO11),
+ UPBOARD_UP2_BIT_TO_PIN(0, SPI2_CLK),
+ UPBOARD_UP2_BIT_TO_PIN(1, SPI1_FS1),
+ UPBOARD_UP2_BIT_TO_PIN(1, SPI1_FS0),
+ UPBOARD_UP2_BIT_TO_PIN(1, SPI1_RXD),
+ UPBOARD_UP2_BIT_TO_PIN(0, SPI1_TXD),
+ UPBOARD_UP2_BIT_TO_PIN(1, SPI1_CLK),
+ UPBOARD_UP2_BIT_TO_PIN(1, PWM0),
+ UPBOARD_UP2_BIT_TO_PIN(1, PWM1),
+ UPBOARD_UP2_BIT_TO_PIN(0, UART1_TXD),
+ UPBOARD_UP2_BIT_TO_PIN(0, UART1_RXD),
+ UPBOARD_UP2_BIT_TO_PIN(0, UART1_CTS),
+ UPBOARD_UP2_BIT_TO_PIN(0, UART1_RTS),
+ UPBOARD_UP2_BIT_TO_PIN(2, I2S_BCLK),
+ UPBOARD_UP2_BIT_TO_PIN(2, I2S_WS_SYNC),
+ UPBOARD_UP2_BIT_TO_PIN(2, I2S_SDI),
+ UPBOARD_UP2_BIT_TO_PIN(2, I2S_SDO),
+ UPBOARD_UP2_BIT_TO_PIN(0, GPIO6),
+ UPBOARD_UP2_BIT_TO_PIN(0, SPI2_FS1),
+ UPBOARD_UP2_BIT_TO_PIN(0, SPI2_RXD),
+ UPBOARD_UP2_BIT_TO_PIN(0, SPI2_TXD),
+ UPBOARD_UP2_BIT_TO_PIN(0, SPI2_FS0),
+ UPBOARD_UP2_BIT_TO_PIN(0, GPIO5),
+};
+
+/*
+ * Init patches applied to the registers until the BIOS sets proper defaults
+ */
+static const struct reg_sequence upboard_up2_reg_patches[] __initconst = {
+ // enable I2C voltage-level shifters
+ { UPFPGA_REG_FUNC_EN0,
+ BIT(UPFPGA_I2C0_EN) |
+ BIT(UPFPGA_I2C1_EN)
+ },
+ // HAT function pins initially set as inputs
+ { UPFPGA_REG_GPIO_DIR0,
+ BIT(UPFPGA_UP2_UART1_RXD) |
+ BIT(UPFPGA_UP2_UART1_CTS)
+ },
+ { UPFPGA_REG_GPIO_DIR1,
+ BIT(UPFPGA_UP2_SPI1_RXD)
+ },
+ // HAT function pins initially enabled (i.e. not hi-Z)
+ { UPFPGA_REG_GPIO_EN0,
+ BIT(UPFPGA_UP2_UART1_TXD) |
+ BIT(UPFPGA_UP2_UART1_RXD) |
+ BIT(UPFPGA_UP2_UART1_RTS) |
+ BIT(UPFPGA_UP2_UART1_CTS) |
+ BIT(UPFPGA_UP2_SPI1_TXD)
+ },
+ { UPFPGA_REG_GPIO_EN1,
+ BIT(UPFPGA_UP2_SPI1_RXD) |
+ BIT(UPFPGA_UP2_SPI1_FS1) |
+ BIT(UPFPGA_UP2_SPI1_FS0) |
+ BIT(UPFPGA_UP2_SPI1_CLK) |
+ BIT(UPFPGA_UP2_PWM1) |
+ BIT(UPFPGA_UP2_PWM0)
+ },
+};
+
+static const struct upboard_bios upboard_up2_bios_info_v0_3 __initconst = {
+ .patches = upboard_up2_reg_patches,
+ .npatches = ARRAY_SIZE(upboard_up2_reg_patches),
+};
+
+/*
+ * UP Core board + CREX carrier board data
+ */
+
+#define UPBOARD_UPCORE_CREX_BIT_TO_PIN(r, id) \
+ (UPBOARD_BIT_TO_PIN(r, UPFPGA_UPCORE_CREX_##id))
+
+#define UPBOARD_UPCORE_CREX_PIN_ANON(r, bit) \
+ { \
+ .number = UPBOARD_BIT_TO_PIN(r, bit), \
+ }
+
+#define UPBOARD_UPCORE_CREX_PIN_NAME(r, id) \
+ { \
+ .number = UPBOARD_UPCORE_CREX_BIT_TO_PIN(r, id), \
+ .name = #id, \
+ }
+
+#define UPBOARD_UPCORE_CREX_PIN_FUNC(r, id, data) \
+ { \
+ .number = UPBOARD_UPCORE_CREX_BIT_TO_PIN(r, id), \
+ .name = #id, \
+ .drv_data = (void *)(data), \
+ }
+
+enum upboard_upcore_crex_reg1_fpgabit {
+ UPFPGA_UPCORE_CREX_I2C0_SDA,
+ UPFPGA_UPCORE_CREX_I2C0_SCL,
+ UPFPGA_UPCORE_CREX_I2C1_SDA,
+ UPFPGA_UPCORE_CREX_I2C1_SCL,
+ UPFPGA_UPCORE_CREX_SPI2_CS0,
+ UPFPGA_UPCORE_CREX_SPI2_CS1,
+ UPFPGA_UPCORE_CREX_SPI2_MOSI,
+ UPFPGA_UPCORE_CREX_SPI2_MISO,
+ UPFPGA_UPCORE_CREX_SPI2_CLK,
+ UPFPGA_UPCORE_CREX_UART1_TXD,
+ UPFPGA_UPCORE_CREX_UART1_RXD,
+ UPFPGA_UPCORE_CREX_PWM0,
+ UPFPGA_UPCORE_CREX_PWM1,
+ UPFPGA_UPCORE_CREX_I2S2_FRM,
+ UPFPGA_UPCORE_CREX_I2S2_CLK,
+ UPFPGA_UPCORE_CREX_I2S2_RX,
+};
+
+enum upboard_upcore_crex_reg2_fpgabit {
+ UPFPGA_UPCORE_CREX_I2S2_TX,
+ UPFPGA_UPCORE_CREX_GPIO0,
+ UPFPGA_UPCORE_CREX_GPIO2,
+ UPFPGA_UPCORE_CREX_GPIO3,
+ UPFPGA_UPCORE_CREX_GPIO4,
+ UPFPGA_UPCORE_CREX_GPIO9,
+};
+
+static struct pinctrl_pin_desc upboard_upcore_crex_pins[] = {
+ UPBOARD_UPCORE_CREX_PIN_FUNC(0, I2C0_SDA, &upboard_i2c0_reg),
+ UPBOARD_UPCORE_CREX_PIN_FUNC(0, I2C0_SCL, &upboard_i2c0_reg),
+ UPBOARD_UPCORE_CREX_PIN_FUNC(0, I2C1_SDA, &upboard_i2c1_reg),
+ UPBOARD_UPCORE_CREX_PIN_FUNC(0, I2C1_SCL, &upboard_i2c1_reg),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, SPI2_CS0),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, SPI2_CS1),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, SPI2_MOSI),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, SPI2_MISO),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, SPI2_CLK),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, UART1_TXD),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, UART1_RXD),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, PWM0),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, PWM1),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, I2S2_FRM),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, I2S2_CLK),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, I2S2_RX),
+ /* register 1 */
+ UPBOARD_UPCORE_CREX_PIN_NAME(1, I2S2_TX),
+ UPBOARD_UPCORE_CREX_PIN_NAME(1, GPIO0),
+ UPBOARD_UPCORE_CREX_PIN_FUNC(1, GPIO2, &upboard_adc0_reg),
+ UPBOARD_UPCORE_CREX_PIN_NAME(1, GPIO3),
+ UPBOARD_UPCORE_CREX_PIN_NAME(1, GPIO4),
+ UPBOARD_UPCORE_CREX_PIN_NAME(1, GPIO9),
+};
+
+static unsigned int upboard_upcore_crex_rpi_mapping[] = {
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, I2C0_SDA),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, I2C0_SCL),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, I2C1_SDA),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, I2C1_SCL),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(1, GPIO0),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(1, GPIO2),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(1, GPIO3),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, SPI2_CS1),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, SPI2_CS0),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, SPI2_MISO),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, SPI2_MOSI),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, SPI2_CLK),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, PWM0),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, PWM1),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, UART1_TXD),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, UART1_RXD),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(1, GPIO9),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(1, GPIO4),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, I2S2_CLK),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, I2S2_FRM),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, I2S2_RX),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(1, I2S2_TX),
+};
+
+/*
+ * Init patches applied to the registers until the BIOS sets proper defaults
+ */
+static const struct reg_sequence upboard_upcore_crex_reg_patches[] __initconst = {
+ // enable I2C voltage-level shifters
+ { UPFPGA_REG_FUNC_EN0,
+ BIT(UPFPGA_I2C0_EN) |
+ BIT(UPFPGA_I2C1_EN)
+ },
+ // HAT function pins initially set as inputs
+ { UPFPGA_REG_GPIO_DIR0,
+ BIT(UPFPGA_UPCORE_CREX_SPI2_MISO) |
+ BIT(UPFPGA_UPCORE_CREX_UART1_RXD) |
+ BIT(UPFPGA_UPCORE_CREX_I2S2_FRM) |
+ BIT(UPFPGA_UPCORE_CREX_I2S2_CLK) |
+ BIT(UPFPGA_UPCORE_CREX_I2S2_RX)
+ },
+};
+
+static const struct upboard_bios upboard_upcore_crex_bios_info __initconst = {
+ .patches = upboard_upcore_crex_reg_patches,
+ .npatches = ARRAY_SIZE(upboard_upcore_crex_reg_patches),
+};
+
+/*
+ * UP Core board + CRST02 carrier board data
+ */
+
+#define upboard_upcore_crst02_pins upboard_upcore_crex_pins
+#define upboard_upcore_crst02_rpi_mapping upboard_upcore_crex_rpi_mapping
+
+/*
+ * Init patches applied to the registers until the BIOS sets proper defaults
+ */
+static const struct reg_sequence upboard_upcore_crst02_reg_patches[] __initconst = {
+ // enable I2C voltage-level shifters
+ { UPFPGA_REG_FUNC_EN0,
+ BIT(UPFPGA_I2C0_EN) |
+ BIT(UPFPGA_I2C1_EN)
+ },
+ // HAT function pins initially set as inputs
+ { UPFPGA_REG_GPIO_DIR0,
+ BIT(UPFPGA_UPCORE_CREX_SPI2_MISO) |
+ BIT(UPFPGA_UPCORE_CREX_UART1_RXD) |
+ BIT(UPFPGA_UPCORE_CREX_I2S2_FRM) |
+ BIT(UPFPGA_UPCORE_CREX_I2S2_CLK) |
+ BIT(UPFPGA_UPCORE_CREX_I2S2_RX)
+ },
+ // HAT function pins initially enabled (i.e. not hi-Z)
+ { UPFPGA_REG_GPIO_EN0,
+ BIT(UPFPGA_UPCORE_CREX_SPI2_CS0) |
+ BIT(UPFPGA_UPCORE_CREX_SPI2_MOSI) |
+ BIT(UPFPGA_UPCORE_CREX_SPI2_MISO) |
+ BIT(UPFPGA_UPCORE_CREX_SPI2_CLK) |
+ BIT(UPFPGA_UPCORE_CREX_UART1_TXD) |
+ BIT(UPFPGA_UPCORE_CREX_UART1_RXD) |
+ BIT(UPFPGA_UPCORE_CREX_PWM0) |
+ BIT(UPFPGA_UPCORE_CREX_PWM1) |
+ BIT(UPFPGA_UPCORE_CREX_I2S2_FRM) |
+ BIT(UPFPGA_UPCORE_CREX_I2S2_CLK) |
+ BIT(UPFPGA_UPCORE_CREX_I2S2_RX)
+ },
+ { UPFPGA_REG_GPIO_EN1,
+ BIT(UPFPGA_UPCORE_CREX_I2S2_TX)
+ },
+};
+
+static const struct upboard_bios upboard_upcore_crst02_bios_info __initconst = {
+ .patches = upboard_upcore_crst02_reg_patches,
+ .npatches = ARRAY_SIZE(upboard_upcore_crst02_reg_patches),
+};
+
+static int upboard_set_mux(struct pinctrl_dev *pctldev, unsigned int function,
+ unsigned int group)
+{
+ return 0;
+};
+
+static int upboard_gpio_request_enable(struct pinctrl_dev *pctldev,
+ struct pinctrl_gpio_range *range,
+ unsigned int pin)
+{
+ const struct pin_desc * const pd = pin_desc_get(pctldev, pin);
+ const struct upboard_pin *p;
+ int ret;
+
+ if (!pd)
+ return -EINVAL;
+ p = pd->drv_data;
+
+ if (p->funcbit) {
+ ret = regmap_field_write(p->funcbit, 0);
+ if (ret)
+ return ret;
+ }
+
+ if (p->enbit) {
+ ret = regmap_field_write(p->enbit, 1);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+};
+
+static int upboard_gpio_set_direction(struct pinctrl_dev *pctldev,
+ struct pinctrl_gpio_range *range,
+ unsigned int pin, bool input)
+{
+ const struct pin_desc * const pd = pin_desc_get(pctldev, pin);
+ const struct upboard_pin *p;
+
+ if (!pd)
+ return -EINVAL;
+ p = pd->drv_data;
+
+ return regmap_field_write(p->dirbit, input);
+};
+
+static int upboard_get_functions_count(struct pinctrl_dev *pctldev)
+{
+ return 0;
+}
+
+static const char *upboard_get_function_name(struct pinctrl_dev *pctldev,
+ unsigned int selector)
+{
+ return NULL;
+}
+
+static int upboard_get_function_groups(struct pinctrl_dev *pctldev,
+ unsigned int selector,
+ const char * const **groups,
+ unsigned int *num_groups)
+{
+ *groups = NULL;
+ *num_groups = 0;
+ return 0;
+}
+
+static const struct pinmux_ops upboard_pinmux_ops = {
+ .get_functions_count = upboard_get_functions_count,
+ .get_function_groups = upboard_get_function_groups,
+ .get_function_name = upboard_get_function_name,
+ .set_mux = upboard_set_mux,
+ .gpio_request_enable = upboard_gpio_request_enable,
+ .gpio_set_direction = upboard_gpio_set_direction,
+};
+
+static int upboard_get_groups_count(struct pinctrl_dev *pctldev)
+{
+ return 0;
+}
+
+static const char *upboard_get_group_name(struct pinctrl_dev *pctldev,
+ unsigned int selector)
+{
+ return NULL;
+}
+
+static const struct pinctrl_ops upboard_pinctrl_ops = {
+ .get_groups_count = upboard_get_groups_count,
+ .get_group_name = upboard_get_group_name,
+};
+
+static struct pinctrl_desc upboard_up_pinctrl_desc = {
+ .pins = upboard_up_pins,
+ .npins = ARRAY_SIZE(upboard_up_pins),
+ .pctlops = &upboard_pinctrl_ops,
+ .pmxops = &upboard_pinmux_ops,
+ .owner = THIS_MODULE,
+};
+
+static struct pinctrl_desc upboard_up2_pinctrl_desc = {
+ .pins = upboard_up2_pins,
+ .npins = ARRAY_SIZE(upboard_up2_pins),
+ .pctlops = &upboard_pinctrl_ops,
+ .pmxops = &upboard_pinmux_ops,
+ .owner = THIS_MODULE,
+};
+
+static struct pinctrl_desc upboard_upcore_crex_pinctrl_desc = {
+ .pins = upboard_upcore_crex_pins,
+ .npins = ARRAY_SIZE(upboard_upcore_crex_pins),
+ .pctlops = &upboard_pinctrl_ops,
+ .pmxops = &upboard_pinmux_ops,
+ .owner = THIS_MODULE,
+};
+
+static struct pinctrl_desc upboard_upcore_crst02_pinctrl_desc = {
+ .pins = upboard_upcore_crst02_pins,
+ .npins = ARRAY_SIZE(upboard_upcore_crst02_pins),
+ .pctlops = &upboard_pinctrl_ops,
+ .pmxops = &upboard_pinmux_ops,
+ .owner = THIS_MODULE,
+};
+
+
+static int upboard_rpi_to_native_gpio(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct upboard_pinctrl *pctrl =
+ container_of(gc, struct upboard_pinctrl, chip);
+ unsigned int pin = pctrl->rpi_mapping[gpio];
+ struct pinctrl_gpio_range *range =
+ pinctrl_find_gpio_range_from_pin(pctrl->pctldev, pin);
+
+ if (!range)
+ return -ENODEV;
+
+ return range->base;
+}
+
+static int upboard_gpio_request(struct gpio_chip *gc, unsigned int offset)
+{
+ int gpio = upboard_rpi_to_native_gpio(gc, offset);
+
+ if (gpio < 0)
+ return gpio;
+
+ return gpio_request(gpio, module_name(THIS_MODULE));
+}
+
+static void upboard_gpio_free(struct gpio_chip *gc, unsigned int offset)
+{
+ int gpio = upboard_rpi_to_native_gpio(gc, offset);
+
+ if (gpio < 0)
+ return;
+
+ gpio_free(gpio);
+}
+
+static int upboard_gpio_get(struct gpio_chip *gc, unsigned int offset)
+{
+ int gpio = upboard_rpi_to_native_gpio(gc, offset);
+
+ if (gpio < 0)
+ return gpio;
+
+ return gpio_get_value(gpio);
+}
+
+static void upboard_gpio_set(struct gpio_chip *gc, unsigned int offset, int
+ value)
+{
+ int gpio = upboard_rpi_to_native_gpio(gc, offset);
+
+ if (gpio < 0)
+ return;
+
+ gpio_set_value(gpio, value);
+}
+
+static int upboard_gpio_direction_input(struct gpio_chip *gc,
+ unsigned int offset)
+{
+ int gpio = upboard_rpi_to_native_gpio(gc, offset);
+
+ if (gpio < 0)
+ return gpio;
+
+ return gpio_direction_input(gpio);
+}
+
+static int upboard_gpio_direction_output(struct gpio_chip *gc,
+ unsigned int offset, int value)
+{
+ int gpio = upboard_rpi_to_native_gpio(gc, offset);
+
+ if (gpio < 0)
+ return gpio;
+
+ return gpio_direction_output(gpio, value);
+}
+
+static struct gpio_chip upboard_gpio_chip = {
+ .label = "Raspberry Pi compatible UP GPIO",
+ .base = 0,
+ .request = upboard_gpio_request,
+ .free = upboard_gpio_free,
+ .get = upboard_gpio_get,
+ .set = upboard_gpio_set,
+ .direction_input = upboard_gpio_direction_input,
+ .direction_output = upboard_gpio_direction_output,
+ .owner = THIS_MODULE,
+};
+
+/* DMI Matches for older bios without fpga initialization */
+static const struct dmi_system_id upboard_dmi_table[] __initconst = {
+ {
+ .matches = { /* UP */
+ DMI_EXACT_MATCH(DMI_SYS_VENDOR, "AAEON"),
+ DMI_EXACT_MATCH(DMI_BOARD_NAME, "UP-CHT01"),
+ DMI_EXACT_MATCH(DMI_BOARD_VERSION, "V0.4"),
+ },
+ .driver_data = (void *)&upboard_up_bios_info_dvt,
+ },
+ {
+ .matches = { /* UP2 */
+ DMI_EXACT_MATCH(DMI_SYS_VENDOR, "AAEON"),
+ DMI_EXACT_MATCH(DMI_BOARD_NAME, "UP-APL01"),
+ DMI_EXACT_MATCH(DMI_BOARD_VERSION, "V0.3"),
+ },
+ .driver_data = (void *)&upboard_up2_bios_info_v0_3,
+ },
+ { },
+};
+
+static int __init upboard_pinctrl_probe(struct platform_device *pdev)
+{
+ struct upboard_fpga * const fpga = dev_get_drvdata(pdev->dev.parent);
+ struct acpi_device * const adev = ACPI_COMPANION(&pdev->dev);
+ struct pinctrl_desc *pctldesc;
+ const struct upboard_bios *bios_info = NULL;
+ struct upboard_pinctrl *pctrl;
+ struct upboard_pin *pins;
+ const struct dmi_system_id *system_id;
+ const char *hid;
+ const unsigned int *rpi_mapping;
+ unsigned int ngpio;
+ int ret;
+ int i;
+
+ if (!fpga)
+ return -EINVAL;
+
+ if (!adev)
+ return -ENODEV;
+
+ hid = acpi_device_hid(adev);
+ if (!strcmp(hid, "AANT0F00") || !strcmp(hid, "AANT0F04")) {
+ pctldesc = &upboard_up_pinctrl_desc;
+ rpi_mapping = upboard_up_rpi_mapping;
+ ngpio = ARRAY_SIZE(upboard_up_rpi_mapping);
+ } else if (!strcmp(hid, "AANT0F01")) {
+ pctldesc = &upboard_up2_pinctrl_desc;
+ rpi_mapping = upboard_up2_rpi_mapping;
+ ngpio = ARRAY_SIZE(upboard_up2_rpi_mapping);
+ } else if (!strcmp(hid, "AANT0F02")) {
+ pctldesc = &upboard_upcore_crex_pinctrl_desc;
+ rpi_mapping = upboard_upcore_crex_rpi_mapping;
+ ngpio = ARRAY_SIZE(upboard_upcore_crex_rpi_mapping);
+ bios_info = &upboard_upcore_crex_bios_info;
+ } else if (!strcmp(hid, "AANT0F03")) {
+ pctldesc = &upboard_upcore_crst02_pinctrl_desc;
+ rpi_mapping = upboard_upcore_crst02_rpi_mapping;
+ ngpio = ARRAY_SIZE(upboard_upcore_crst02_rpi_mapping);
+ bios_info = &upboard_upcore_crst02_bios_info;
+ } else
+ return -ENODEV;
+
+ pctldesc->name = dev_name(&pdev->dev);
+
+ pins = devm_kzalloc(&pdev->dev,
+ sizeof(*pins) * pctldesc->npins,
+ GFP_KERNEL);
+ if (!pins)
+ return -ENOMEM;
+
+ /* initialise pins */
+ for (i = 0; i < pctldesc->npins; i++) {
+ struct upboard_pin *pin = &pins[i];
+ struct pinctrl_pin_desc *pd = (struct pinctrl_pin_desc *)
+ &pctldesc->pins[i];
+ struct reg_field fldconf = {0};
+ unsigned int regoff = (pd->number / UPFPGA_REGISTER_SIZE);
+ unsigned int lsb = pd->number % UPFPGA_REGISTER_SIZE;
+
+ pin->funcbit = NULL;
+ if (pd->drv_data) {
+ fldconf = *(struct reg_field *)pd->drv_data;
+ if (!regmap_writeable(fpga->regmap, fldconf.reg))
+ return -EINVAL;
+
+ pin->funcbit = devm_regmap_field_alloc(&pdev->dev,
+ fpga->regmap,
+ fldconf);
+ if (IS_ERR(pin->funcbit))
+ return PTR_ERR(pin->funcbit);
+ }
+
+ pin->enbit = NULL;
+ fldconf.reg = UPFPGA_REG_GPIO_EN0 + regoff;
+ fldconf.lsb = lsb;
+ fldconf.msb = lsb;
+
+ /* some platform don't have enable bit, ignore if not present */
+ if (regmap_writeable(fpga->regmap, fldconf.reg)) {
+ pin->enbit = devm_regmap_field_alloc(&pdev->dev,
+ fpga->regmap,
+ fldconf);
+ if (IS_ERR(pin->enbit))
+ return PTR_ERR(pin->enbit);
+ }
+
+ fldconf.reg = UPFPGA_REG_GPIO_DIR0 + regoff;
+ fldconf.lsb = lsb;
+ fldconf.msb = lsb;
+
+ if (!regmap_writeable(fpga->regmap, fldconf.reg))
+ return -EINVAL;
+
+ pin->dirbit = devm_regmap_field_alloc(&pdev->dev,
+ fpga->regmap,
+ fldconf);
+ if (IS_ERR(pin->dirbit))
+ return PTR_ERR(pin->dirbit);
+
+ pd->drv_data = pin;
+ }
+
+ /* create a new pinctrl device and register it */
+ pctrl = devm_kzalloc(&pdev->dev, sizeof(*pctrl), GFP_KERNEL);
+ if (!pctrl)
+ return -ENOMEM;
+
+ pctrl->regmap = fpga->regmap;
+ pctrl->rpi_mapping = rpi_mapping;
+ pctrl->chip = upboard_gpio_chip;
+ pctrl->chip.parent = &pdev->dev;
+ pctrl->chip.ngpio = ngpio;
+
+ ret = devm_gpiochip_add_data(&pdev->dev, &pctrl->chip, &pctrl->chip);
+ if (ret)
+ return ret;
+
+ pctrl->pctldev = devm_pinctrl_register(&pdev->dev, pctldesc, pctrl);
+ if (IS_ERR(pctrl->pctldev))
+ return PTR_ERR(pctrl->pctldev);
+
+ /* add acpi pin mapping according to external-gpios key */
+ ret = acpi_node_add_pin_mapping(acpi_fwnode_handle(adev),
+ "external-gpios",
+ dev_name(&pdev->dev),
+ 0, UINT_MAX);
+ if (ret)
+ return ret;
+
+ if (!bios_info) {
+ /* check for special board versions that require register patches */
+ system_id = dmi_first_match(upboard_dmi_table);
+ if (system_id)
+ bios_info = system_id->driver_data;
+ }
+
+ if (bios_info && bios_info->patches) {
+ ret = regmap_register_patch(pctrl->regmap,
+ bios_info->patches,
+ bios_info->npatches);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static struct platform_driver upboard_pinctrl_driver = {
+ .driver = {
+ .name = "upboard-pinctrl",
+ },
+};
+
+module_platform_driver_probe(upboard_pinctrl_driver, upboard_pinctrl_probe);
+
+MODULE_AUTHOR("Javier Arteaga <javier@...tex.com>");
+MODULE_AUTHOR("Dan O'Donovan <dan@...tex.com>");
+MODULE_AUTHOR("Nicola Lunghi <nicolal@...tex.com>");
+MODULE_DESCRIPTION("UP Board HAT pin controller driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:upboard-pinctrl");
--
2.17.1
Powered by blists - more mailing lists