| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <e0ca517d-30d7-db19-4a67-073ae4411a2f@microchip.com>
Date: Tue, 15 Nov 2022 05:40:26 +0000
From: <Durai.ManickamKR@...rochip.com>
To: <Claudiu.Beznea@...rochip.com>, <Nicolas.Ferre@...rochip.com>,
<Cristian.Birsan@...rochip.com>, <Hari.PrasathGE@...rochip.com>,
<davem@...emloft.net>, <krzysztof.kozlowski+dt@...aro.org>,
<alexandre.belloni@...tlin.com>, <arnd@...db.de>, <olof@...om.net>,
<soc@...nel.org>, <devicetree@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-kernel@...r.kernel.org>, <Manikandan.M@...rochip.com>,
<Kavyasree.Kotagiri@...rochip.com>, <Horatiu.Vultur@...rochip.com>
Subject: Re: [PATCHv1 6/8] ARM: dts: at91: sam9x60: Add missing flexcom
definitions
On 31/10/22 15:58, Claudiu Beznea - M18063 wrote:
> On 31.10.2022 05:36, Durai Manickam KR wrote:
>> Added the missing flexcom functions for all the flexcom nodes.
>>
>> Signed-off-by: Durai Manickam KR <durai.manickamkr@...rochip.com>
>> Signed-off-by: Hari Prasath <Hari.PrasathGE@...rochip.com>
>> Signed-off-by: Manikandan M <manikandan.m@...rochip.com>
>> ---
>> arch/arm/boot/dts/sam9x60.dtsi | 547 +++++++++++++++++++++++++++++++++
>> 1 file changed, 547 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
>> index 74599d21ebcc..4902a2e5fc21 100644
>> --- a/arch/arm/boot/dts/sam9x60.dtsi
>> +++ b/arch/arm/boot/dts/sam9x60.dtsi
>> @@ -171,6 +171,27 @@ flx4: flexcom@...00000 {
>> ranges = <0x0 0xf0000000 0x800>;
>> status = "disabled";
>>
>> + uart4: serial@200 {
>> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
>> + reg = <0x200 0x200>;
>> + interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(8))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(9))>;
>> + dma-names = "tx", "rx";
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
>> + clock-names = "usart";
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> +
>> spi4: spi@400 {
>> compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
>> reg = <0x400 0x200>;
>> @@ -189,6 +210,24 @@ AT91_XDMAC_DT_PER_IF(1) |
>> atmel,fifo-size = <16>;
>> status = "disabled";
>> };
>> +
>> + i2c4: i2c@600 {
>> + compatible = "microchip,sam9x60-i2c";
>> + reg = <0x600 0x200>;
>> + interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(8))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(9))>;
>> + dma-names = "tx", "rx";
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> };
>>
>> flx5: flexcom@...04000 {
>> @@ -220,6 +259,43 @@ AT91_XDMAC_DT_PER_IF(1) |
>> atmel,fifo-size = <16>;
>> status = "disabled";
>> };
>> +
>> + spi5: spi@400 {
>> + compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
>> + reg = <0x400 0x200>;
>> + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
>> + clock-names = "spi_clk";
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(10))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(11))>;
>> + dma-names = "tx", "rx";
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> +
>> + i2c5: i2c@600 {
>> + compatible = "microchip,sam9x60-i2c";
>> + reg = <0x600 0x200>;
>> + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(10))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(11))>;
>> + dma-names = "tx", "rx";
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> };
>>
>> dma0: dma-controller@...08000 {
>> @@ -302,6 +378,45 @@ flx11: flexcom@...20000 {
>> #size-cells = <1>;
>> ranges = <0x0 0xf0020000 0x800>;
>> status = "disabled";
>> +
>> + uart11: serial@200 {
>> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
>> + reg = <0x200 0x200>;
>> + interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(22))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(23))>;
>> + dma-names = "tx", "rx";
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
>> + clock-names = "usart";
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> +
>> + i2c11: i2c@600 {
>> + compatible = "microchip,sam9x60-i2c";
>> + reg = <0x600 0x200>;
>> + interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(22))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(23))>;
>> + dma-names = "tx", "rx";
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> };
>>
>> flx12: flexcom@...24000 {
>> @@ -312,6 +427,45 @@ flx12: flexcom@...24000 {
>> #size-cells = <1>;
>> ranges = <0x0 0xf0024000 0x800>;
>> status = "disabled";
>> +
>> + uart12: serial@200 {
>> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
>> + reg = <0x200 0x200>;
>> + interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(24))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(25))>;
>> + dma-names = "tx", "rx";
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
>> + clock-names = "usart";
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> +
>> + i2c12: i2c@600 {
>> + compatible = "microchip,sam9x60-i2c";
>> + reg = <0x600 0x200>;
>> + interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(24))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(25))>;
>> + dma-names = "tx", "rx";
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> };
>>
>> pit64b: timer@...28000 {
>> @@ -431,6 +585,27 @@ flx6: flexcom@...10000 {
>> ranges = <0x0 0xf8010000 0x800>;
>> status = "disabled";
>>
>> + uart6: serial@200 {
>> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
>> + reg = <0x200 0x200>;
>> + interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(12))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(13))>;
>> + dma-names = "tx", "rx";
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
>> + clock-names = "usart";
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> +
>> i2c6: i2c@600 {
>> compatible = "microchip,sam9x60-i2c";
>> reg = <0x600 0x200>;
>> @@ -458,6 +633,45 @@ flx7: flexcom@...14000 {
>> #size-cells = <1>;
>> ranges = <0x0 0xf8014000 0x800>;
>> status = "disabled";
>> +
>> + uart7: serial@200 {
>> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
>> + reg = <0x200 0x200>;
>> + interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(14))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(15))>;
>> + dma-names = "tx", "rx";
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
>> + clock-names = "usart";
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> +
>> + i2c7: i2c@600 {
>> + compatible = "microchip,sam9x60-i2c";
>> + reg = <0x600 0x200>;
>> + interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(14))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(15))>;
>> + dma-names = "tx", "rx";
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> };
>>
>> flx8: flexcom@...18000 {
>> @@ -468,15 +682,96 @@ flx8: flexcom@...18000 {
>> #size-cells = <1>;
>> ranges = <0x0 0xf8018000 0x800>;
>> status = "disabled";
>> +
>> + uart8: serial@200 {
>> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
>> + reg = <0x200 0x200>;
>> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(16))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(17))>;
>> + dma-names = "tx", "rx";
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
>> + clock-names = "usart";
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> +
>> + i2c8: i2c@600 {
>> + compatible = "microchip,sam9x60-i2c";
>> + reg = <0x600 0x200>;
>> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(16))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(17))>;
>> + dma-names = "tx", "rx";
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> };
>>
>> flx0: flexcom@...1c000 {
>> compatible = "atmel,sama5d2-flexcom";
>> reg = <0xf801c000 0x200>;
>> clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
> This should go in a different patch.
>
> Appart from that some flexcom nodes don't have all the subnodes added but
> only a part of them. Is this by intention?
Hi Claudiu,
Some of the flexcom nodes does not have all the controller like UART,
I2C and SPI. So referring the datasheet we have added all the available
nodes for the flexcom.
>
>> ranges = <0x0 0xf801c000 0x800>;
>> status = "disabled";
>>
>> + uart0: serial@200 {
>> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
>> + reg = <0x200 0x200>;
>> + interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(0))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(1))>;
>> + dma-names = "tx", "rx";
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
>> + clock-names = "usart";
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> +
>> + spi0: spi@400 {
>> + compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
>> + reg = <0x400 0x200>;
>> + interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
>> + clock-names = "spi_clk";
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(0))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(1))>;
>> + dma-names = "tx", "rx";
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> +
>> i2c0: i2c@600 {
>> compatible = "microchip,sam9x60-i2c";
>> reg = <0x600 0x200>;
>> @@ -506,6 +801,64 @@ flx1: flexcom@...20000 {
>> #size-cells = <1>;
>> ranges = <0x0 0xf8020000 0x800>;
>> status = "disabled";
>> +
>> + uart1: serial@200 {
>> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
>> + reg = <0x200 0x200>;
>> + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(2))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(3))>;
>> + dma-names = "tx", "rx";
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
>> + clock-names = "usart";
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> +
>> + spi1: spi@400 {
>> + compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
>> + reg = <0x400 0x200>;
>> + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
>> + clock-names = "spi_clk";
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(2))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(3))>;
>> + dma-names = "tx", "rx";
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> +
>> + i2c1: i2c@600 {
>> + compatible = "microchip,sam9x60-i2c";
>> + reg = <0x600 0x200>;
>> + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(2))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(3))>;
>> + dma-names = "tx", "rx";
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> };
>>
>> flx2: flexcom@...24000 {
>> @@ -516,6 +869,64 @@ flx2: flexcom@...24000 {
>> #size-cells = <1>;
>> ranges = <0x0 0xf8024000 0x800>;
>> status = "disabled";
>> +
>> + uart2: serial@200 {
>> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
>> + reg = <0x200 0x200>;
>> + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(4))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(5))>;
>> + dma-names = "tx", "rx";
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
>> + clock-names = "usart";
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> +
>> + spi2: spi@400 {
>> + compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
>> + reg = <0x400 0x200>;
>> + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
>> + clock-names = "spi_clk";
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(4))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(5))>;
>> + dma-names = "tx", "rx";
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> +
>> + i2c2: i2c@600 {
>> + compatible = "microchip,sam9x60-i2c";
>> + reg = <0x600 0x200>;
>> + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(4))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(5))>;
>> + dma-names = "tx", "rx";
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> };
>>
>> flx3: flexcom@...28000 {
>> @@ -526,6 +937,64 @@ flx3: flexcom@...28000 {
>> #size-cells = <1>;
>> ranges = <0x0 0xf8028000 0x800>;
>> status = "disabled";
>> +
>> + uart3: serial@200 {
>> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
>> + reg = <0x200 0x200>;
>> + interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(6))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(7))>;
>> + dma-names = "tx", "rx";
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
>> + clock-names = "usart";
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> +
>> + spi3: spi@400 {
>> + compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
>> + reg = <0x400 0x200>;
>> + interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
>> + clock-names = "spi_clk";
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(6))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(7))>;
>> + dma-names = "tx", "rx";
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> +
>> + i2c3: i2c@600 {
>> + compatible = "microchip,sam9x60-i2c";
>> + reg = <0x600 0x200>;
>> + interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(6))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(7))>;
>> + dma-names = "tx", "rx";
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> };
>>
>> macb0: ethernet@...2c000 {
>> @@ -591,6 +1060,45 @@ flx9: flexcom@...40000 {
>> #size-cells = <1>;
>> ranges = <0x0 0xf8040000 0x800>;
>> status = "disabled";
>> +
>> + uart9: serial@200 {
>> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
>> + reg = <0x200 0x200>;
>> + interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(18))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(19))>;
>> + dma-names = "tx", "rx";
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
>> + clock-names = "usart";
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> +
>> + i2c9: i2c@600 {
>> + compatible = "microchip,sam9x60-i2c";
>> + reg = <0x600 0x200>;
>> + interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(18))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(19))>;
>> + dma-names = "tx", "rx";
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> };
>>
>> flx10: flexcom@...44000 {
>> @@ -601,6 +1109,45 @@ flx10: flexcom@...44000 {
>> #size-cells = <1>;
>> ranges = <0x0 0xf8044000 0x800>;
>> status = "disabled";
>> +
>> + uart10: serial@200 {
>> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
>> + reg = <0x200 0x200>;
>> + interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(20))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(21))>;
>> + dma-names = "tx", "rx";
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
>> + clock-names = "usart";
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> +
>> + i2c10: i2c@600 {
>> + compatible = "microchip,sam9x60-i2c";
>> + reg = <0x600 0x200>;
>> + interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
>> + clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(20))>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) |
>> + AT91_XDMAC_DT_PER_IF(1) |
>> + AT91_XDMAC_DT_PERID(21))>;
>> + dma-names = "tx", "rx";
>> + atmel,fifo-size = <16>;
>> + status = "disabled";
>> + };
>> };
>>
>> isi: isi@...48000 {
Powered by blists - more mailing lists