| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <5d5baf82-7fce-27d9-c8af-22246ed98913@linaro.org>
Date: Wed, 16 Nov 2022 12:08:10 +0100
From: Konrad Dybcio <konrad.dybcio@...aro.org>
To: Abel Vesa <abel.vesa@...aro.org>, Andy Gross <agross@...nel.org>,
Bjorn Andersson <andersson@...nel.org>,
Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski@...aro.org>,
Neil Armstrong <neil.armstrong@...aro.org>
Cc: linux-arm-msm@...r.kernel.org, devicetree@...r.kernel.org,
Linux Kernel Mailing List <linux-kernel@...r.kernel.org>,
"vkoul@...nel.org" <vkoul@...nel.org>,
Srinivas Kandagatla <srinivas.kandagatla@...aro.org>
Subject: Re: [PATCH 07/10] arm64: dts: qcom: Add PM8550vs pmic dtsi
On 16/11/2022 11:31, Abel Vesa wrote:
> From: Neil Armstrong <neil.armstrong@...aro.org>
>
> Add nodes for PM8550vs in separate dtsi file.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@...aro.org>
> ---
That's a lot of GPIOs!
Reviewed-by: Konrad Dybcio <konrad.dybcio@...aro.org>
Konrad
> arch/arm64/boot/dts/qcom/pm8550vs.dtsi | 194 +++++++++++++++++++++++++
> 1 file changed, 194 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/pm8550vs.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/pm8550vs.dtsi b/arch/arm64/boot/dts/qcom/pm8550vs.dtsi
> new file mode 100644
> index 000000000000..97b1c18aa7d8
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/pm8550vs.dtsi
> @@ -0,0 +1,194 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2022, Linaro Limited
> + */
> +
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/spmi/spmi.h>
> +
> +/ {
> + thermal-zones {
> + pm8550vs-c-thermal {
> + polling-delay-passive = <100>;
> + polling-delay = <0>;
> +
> + thermal-sensors = <&pm8550vs_c_temp_alarm>;
> +
> + trips {
> + trip0 {
> + temperature = <95000>;
> + hysteresis = <0>;
> + type = "passive";
> + };
> +
> + trip1 {
> + temperature = <115000>;
> + hysteresis = <0>;
> + type = "hot";
> + };
> + };
> + };
> +
> + pm8550vs-d-thermal {
> + polling-delay-passive = <100>;
> + polling-delay = <0>;
> +
> + thermal-sensors = <&pm8550vs_d_temp_alarm>;
> +
> + trips {
> + trip0 {
> + temperature = <95000>;
> + hysteresis = <0>;
> + type = "passive";
> + };
> +
> + trip1 {
> + temperature = <115000>;
> + hysteresis = <0>;
> + type = "hot";
> + };
> + };
> + };
> +
> + pm8550vs-e-thermal {
> + polling-delay-passive = <100>;
> + polling-delay = <0>;
> +
> + thermal-sensors = <&pm8550vs_e_temp_alarm>;
> +
> + trips {
> + trip0 {
> + temperature = <95000>;
> + hysteresis = <0>;
> + type = "passive";
> + };
> +
> + trip1 {
> + temperature = <115000>;
> + hysteresis = <0>;
> + type = "hot";
> + };
> + };
> + };
> +
> + pm8550vs-g-thermal {
> + polling-delay-passive = <100>;
> + polling-delay = <0>;
> +
> + thermal-sensors = <&pm8550vs_g_temp_alarm>;
> +
> + trips {
> + trip0 {
> + temperature = <95000>;
> + hysteresis = <0>;
> + type = "passive";
> + };
> +
> + trip1 {
> + temperature = <115000>;
> + hysteresis = <0>;
> + type = "hot";
> + };
> + };
> + };
> + };
> +};
> +
> +
> +&spmi_bus {
> + pm8550vs_c: pmic@2 {
> + compatible = "qcom,pm8550", "qcom,spmi-pmic";
> + reg = <0x2 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pm8550vs_c_temp_alarm: temp-alarm@a00 {
> + compatible = "qcom,spmi-temp-alarm";
> + reg = <0xa00>;
> + interrupts = <0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> + #thermal-sensor-cells = <0>;
> + };
> +
> + pm8550vs_c_gpios: gpio@...0 {
> + compatible = "qcom,pm8550vs-gpio", "qcom,spmi-gpio";
> + reg = <0x8800>;
> + gpio-controller;
> + gpio-ranges = <&pm8550vs_c_gpios 0 0 6>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + pm8550vs_d: pmic@3 {
> + compatible = "qcom,pm8550", "qcom,spmi-pmic";
> + reg = <0x3 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pm8550vs_d_temp_alarm: temp-alarm@a00 {
> + compatible = "qcom,spmi-temp-alarm";
> + reg = <0xa00>;
> + interrupts = <0x3 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> + #thermal-sensor-cells = <0>;
> + };
> +
> + pm8550vs_d_gpios: gpio@...0 {
> + compatible = "qcom,pm8550vs-gpio", "qcom,spmi-gpio";
> + reg = <0x8800>;
> + gpio-controller;
> + gpio-ranges = <&pm8550vs_d_gpios 0 0 6>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + pm8550vs_e: pmic@4 {
> + compatible = "qcom,pm8550", "qcom,spmi-pmic";
> + reg = <0x4 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pm8550vs_e_temp_alarm: temp-alarm@a00 {
> + compatible = "qcom,spmi-temp-alarm";
> + reg = <0xa00>;
> + interrupts = <0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> + #thermal-sensor-cells = <0>;
> + };
> +
> + pm8550vs_e_gpios: gpio@...0 {
> + compatible = "qcom,pm8550vs-gpio", "qcom,spmi-gpio";
> + reg = <0x8800>;
> + gpio-controller;
> + gpio-ranges = <&pm8550vs_e_gpios 0 0 6>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + pm8550vs_g: pmic@6 {
> + compatible = "qcom,pm8550", "qcom,spmi-pmic";
> + reg = <0x6 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pm8550vs_g_temp_alarm: temp-alarm@a00 {
> + compatible = "qcom,spmi-temp-alarm";
> + reg = <0xa00>;
> + interrupts = <0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> + #thermal-sensor-cells = <0>;
> + };
> +
> + pm8550vs_g_gpios: gpio@...0 {
> + compatible = "qcom,pm8550vs-gpio", "qcom,spmi-gpio";
> + reg = <0x8800>;
> + gpio-controller;
> + gpio-ranges = <&pm8550vs_g_gpios 0 0 6>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +};
Powered by blists - more mailing lists