| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20221124115712.v4.2.I56fb5003a3ac94e90d3068be274e6f9357fdd130@changeid>
Date: Thu, 24 Nov 2022 11:57:29 +0800
From: Owen Yang <ecs.taipeikernel@...il.com>
To: LKML <linux-kernel@...r.kernel.org>
Cc: Bob Moragues <moragues@...omium.org>,
Krzysztof Kozlowski <krzysztof.kozlowski@...aro.org>,
Stephen Boyd <swboyd@...omium.org>, Harvey <hunge@...gle.com>,
Douglas Anderson <dianders@...omium.org>,
Matthias Kaehlcke <mka@...omium.org>,
Owen Yang <ecs.taipeikernel@...il.com>,
Andy Gross <agross@...nel.org>,
Bjorn Andersson <andersson@...nel.org>,
Konrad Dybcio <konrad.dybcio@...aro.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Rob Herring <robh+dt@...nel.org>, devicetree@...r.kernel.org,
linux-arm-msm@...r.kernel.org
Subject: [PATCH v4 2/2] arm64: dts: qcom: sc7280: Add DT for sc7280-herobrine-zombie
Add DT for sc7280-herobrine-zombie
Signed-off-by: Owen Yang <ecs.taipeikernel@...il.com>
---
(no changes since v1)
arch/arm64/boot/dts/qcom/Makefile | 2 +
.../dts/qcom/sc7280-herobrine-zombie-lte.dts | 16 +
.../boot/dts/qcom/sc7280-herobrine-zombie.dts | 16 +
.../dts/qcom/sc7280-herobrine-zombie.dtsi | 309 ++++++++++++++++++
4 files changed, 343 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sc7280-herobrine-zombie-lte.dts
create mode 100644 arch/arm64/boot/dts/qcom/sc7280-herobrine-zombie.dts
create mode 100644 arch/arm64/boot/dts/qcom/sc7280-herobrine-zombie.dtsi
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index afe496a93f94..7b0644a39062 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -114,6 +114,8 @@ dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-herobrine-r1.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-villager-r0.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-villager-r1.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-villager-r1-lte.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-zombie.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-zombie-lte.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp2.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-crd-r3.dtb
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-zombie-lte.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-zombie-lte.dts
new file mode 100644
index 000000000000..c9fe64529555
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-zombie-lte.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Zombie board device tree source
+ *
+ * Copyright 2022 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7280-herobrine-zombie.dtsi"
+#include "sc7280-herobrine-lte-sku.dtsi"
+
+/ {
+ model = "Google Zombie with LTE";
+ compatible = "google,zombie-sku512", "qcom,sc7280";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-zombie.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-zombie.dts
new file mode 100644
index 000000000000..0246c12b2f40
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-zombie.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Zombie board device tree source
+ *
+ * Copyright 2022 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7280-herobrine-zombie.dtsi"
+#include "sc7280-herobrine-wifi-sku.dtsi"
+
+/ {
+ model = "Google Zombie";
+ compatible = "google,zombie", "qcom,sc7280";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-zombie.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine-zombie.dtsi
new file mode 100644
index 000000000000..3de03602e1f7
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-zombie.dtsi
@@ -0,0 +1,309 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Zombie board device tree source
+ *
+ * Copyright 2022 Google LLC.
+ */
+
+#include "sc7280-herobrine.dtsi"
+#include "sc7280-herobrine-audio-rt5682.dtsi"
+
+/*
+ * ADDITIONS TO FIXED REGULATORS DEFINED IN PARENT DEVICE TREE FILES
+ *
+ * Sort order matches the order in the parent files (parents before children).
+ */
+
+&pp3300_codec {
+ status = "okay";
+};
+
+/* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */
+
+ap_tp_i2c: &i2c0 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ trackpad: trackpad@15 {
+ compatible = "hid-over-i2c";
+ reg = <0x15>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&tp_int_odl>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+
+ hid-descr-addr = <0x01>;
+ vdd-supply = <&pp3300_z1>;
+ post-power-on-delay-ms = <100>;
+
+ wakeup-source;
+ };
+};
+
+&ap_sar_sensor_i2c {
+ status = "okay";
+};
+
+&ap_sar_sensor0 {
+ status = "okay";
+};
+
+&ap_sar_sensor1 {
+ status = "okay";
+};
+
+&mdss_edp {
+ status = "okay";
+};
+
+&mdss_edp_phy {
+ status = "okay";
+};
+
+/* For nvme */
+&pcie1 {
+ status = "okay";
+};
+
+/* For nvme */
+&pcie1_phy {
+ status = "okay";
+};
+
+&pwmleds {
+ status = "okay";
+};
+
+/* For eMMC */
+&sdhc_1 {
+ status = "okay";
+};
+
+/* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */
+
+&ts_rst_conn {
+ bias-disable;
+};
+
+/* PINCTRL - BOARD-SPECIFIC */
+
+/*
+ * Methodology for gpio-line-names:
+ * - If a pin goes to herobrine board and is named it gets that name.
+ * - If a pin goes to herobrine board and is not named, it gets no name.
+ * - If a pin is totally internal to Qcard then it gets Qcard name.
+ * - If a pin is not hooked up on Qcard, it gets no name.
+ */
+
+&pm8350c_gpios {
+ gpio-line-names = "FLASH_STROBE_1", /* 1 */
+ "AP_SUSPEND",
+ "PM8008_1_RST_N",
+ "",
+ "",
+ "",
+ "PMIC_EDP_BL_EN",
+ "PMIC_EDP_BL_PWM",
+ "";
+};
+
+&tlmm {
+ gpio-line-names = "AP_TP_I2C_SDA", /* 0 */
+ "AP_TP_I2C_SCL",
+ "SSD_RST_L",
+ "PE_WAKE_ODL",
+ "AP_SAR_SDA",
+ "AP_SAR_SCL",
+ "PRB_SC_GPIO_6",
+ "TP_INT_ODL",
+ "HP_I2C_SDA",
+ "HP_I2C_SCL",
+
+ "GNSS_L1_EN", /* 10 */
+ "GNSS_L5_EN",
+ "SPI_AP_MOSI",
+ "SPI_AP_MISO",
+ "SPI_AP_CLK",
+ "SPI_AP_CS0_L",
+ /*
+ * AP_FLASH_WP is crossystem ABI. Schematics
+ * call it BIOS_FLASH_WP_OD.
+ */
+ "AP_FLASH_WP",
+ "",
+ "AP_EC_INT_L",
+ "",
+
+ "UF_CAM_RST_L", /* 20 */
+ "WF_CAM_RST_L",
+ "UART_AP_TX_DBG_RX",
+ "UART_DBG_TX_AP_RX",
+ "",
+ "PM8008_IRQ_1",
+ "HOST2WLAN_SOL",
+ "WLAN2HOST_SOL",
+ "MOS_BT_UART_CTS",
+ "MOS_BT_UART_RFR",
+
+ "MOS_BT_UART_TX", /* 30 */
+ "MOS_BT_UART_RX",
+ "PRB_SC_GPIO_32",
+ "HUB_RST_L",
+ "",
+ "",
+ "AP_SPI_FP_MISO",
+ "AP_SPI_FP_MOSI",
+ "AP_SPI_FP_CLK",
+ "AP_SPI_FP_CS_L",
+
+ "AP_EC_SPI_MISO", /* 40 */
+ "AP_EC_SPI_MOSI",
+ "AP_EC_SPI_CLK",
+ "AP_EC_SPI_CS_L",
+ "LCM_RST_L",
+ "EARLY_EUD_N",
+ "",
+ "DP_HOT_PLUG_DET",
+ "IO_BRD_MLB_ID0",
+ "IO_BRD_MLB_ID1",
+
+ "IO_BRD_MLB_ID2", /* 50 */
+ "SSD_EN",
+ "TS_I2C_SDA_CONN",
+ "TS_I2C_CLK_CONN",
+ "TS_RST_CONN",
+ "TS_INT_CONN",
+ "AP_I2C_TPM_SDA",
+ "AP_I2C_TPM_SCL",
+ "PRB_SC_GPIO_58",
+ "PRB_SC_GPIO_59",
+
+ "EDP_HOT_PLUG_DET_N", /* 60 */
+ "FP_TO_AP_IRQ_L",
+ "",
+ "AMP_EN",
+ "CAM0_MCLK_GPIO_64",
+ "CAM1_MCLK_GPIO_65",
+ "WF_CAM_MCLK",
+ "PRB_SC_GPIO_67",
+ "FPMCU_BOOT0",
+ "UF_CAM_SDA",
+
+ "UF_CAM_SCL", /* 70 */
+ "",
+ "",
+ "WF_CAM_SDA",
+ "WF_CAM_SCL",
+ "",
+ "",
+ "EN_FP_RAILS",
+ "FP_RST_L",
+ "PCIE1_CLKREQ_ODL",
+
+ "EN_PP3300_DX_EDP", /* 80 */
+ "US_EURO_HS_SEL",
+ "FORCED_USB_BOOT",
+ "WCD_RESET_N",
+ "MOS_WLAN_EN",
+ "MOS_BT_EN",
+ "MOS_SW_CTRL",
+ "MOS_PCIE0_RST",
+ "MOS_PCIE0_CLKREQ_N",
+ "MOS_PCIE0_WAKE_N",
+
+ "MOS_LAA_AS_EN", /* 90 */
+ "SD_CD_ODL",
+ "",
+ "",
+ "MOS_BT_WLAN_SLIMBUS_CLK",
+ "MOS_BT_WLAN_SLIMBUS_DAT0",
+ "HP_MCLK",
+ "HP_BCLK",
+ "HP_DOUT",
+ "HP_DIN",
+
+ "HP_LRCLK", /* 100 */
+ "HP_IRQ",
+ "",
+ "",
+ "GSC_AP_INT_ODL",
+ "EN_PP3300_CODEC",
+ "AMP_BCLK",
+ "AMP_DIN",
+ "AMP_LRCLK",
+ "UIM1_DATA_GPIO_109",
+
+ "UIM1_CLK_GPIO_110", /* 110 */
+ "UIM1_RESET_GPIO_111",
+ "PRB_SC_GPIO_112",
+ "UIM0_DATA",
+ "UIM0_CLK",
+ "UIM0_RST",
+ "UIM0_PRESENT_ODL",
+ "SDM_RFFE0_CLK",
+ "SDM_RFFE0_DATA",
+ "WF_CAM_EN",
+
+ "FASTBOOT_SEL_0", /* 120 */
+ "SC_GPIO_121",
+ "FASTBOOT_SEL_1",
+ "SC_GPIO_123",
+ "FASTBOOT_SEL_2",
+ "SM_RFFE4_CLK_GRFC_8",
+ "SM_RFFE4_DATA_GRFC_9",
+ "WLAN_COEX_UART1_RX",
+ "WLAN_COEX_UART1_TX",
+ "PRB_SC_GPIO_129",
+
+ "LCM_ID0", /* 130 */
+ "LCM_ID1",
+ "",
+ "SDR_QLINK_REQ",
+ "SDR_QLINK_EN",
+ "QLINK0_WMSS_RESET_N",
+ "SMR526_QLINK1_REQ",
+ "SMR526_QLINK1_EN",
+ "SMR526_QLINK1_WMSS_RESET_N",
+ "PRB_SC_GPIO_139",
+
+ "SAR1_IRQ_ODL", /* 140 */
+ "SAR0_IRQ_ODL",
+ "PRB_SC_GPIO_142",
+ "",
+ "WCD_SWR_TX_CLK",
+ "WCD_SWR_TX_DATA0",
+ "WCD_SWR_TX_DATA1",
+ "WCD_SWR_RX_CLK",
+ "WCD_SWR_RX_DATA0",
+ "WCD_SWR_RX_DATA1",
+
+ "DMIC01_CLK", /* 150 */
+ "DMIC01_DATA",
+ "DMIC23_CLK",
+ "DMIC23_DATA",
+ "",
+ "",
+ "EC_IN_RW_ODL",
+ "HUB_EN",
+ "WCD_SWR_TX_DATA2",
+ "",
+
+ "", /* 160 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+
+ "", /* 170 */
+ "MOS_BLE_UART_TX",
+ "MOS_BLE_UART_RX",
+ "",
+ "",
+ "";
+};
--
2.17.1
Powered by blists - more mailing lists