| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Mon, 12 Dec 2022 11:02:32 +0100
From: Krzysztof Kozlowski <krzysztof.kozlowski@...aro.org>
To: Andy Gross <agross@...nel.org>,
Bjorn Andersson <andersson@...nel.org>,
Konrad Dybcio <konrad.dybcio@...aro.org>,
Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@...aro.org>,
linux-arm-msm@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org
Subject: [PATCH v2 6/6] arm64: dts: qcom: sm8250: move sound and codec nodes out of soc
The sound and on-board WCD9380 codec nodes are not properties of the
soc, but rather board as it describes the sound configuration. They also
does not have unit addresses:
sm8250-hdk.dtb: soc@0: sound: {} should not be valid under {'type': 'object'}
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@...aro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@...aro.org>
---
Changes since v1:
1. Add Rb tag.
2. Rephrase commit msg.
---
arch/arm64/boot/dts/qcom/sm8250-mtp.dts | 40 ++++++++++++-------------
arch/arm64/boot/dts/qcom/sm8250.dtsi | 6 ++--
2 files changed, 22 insertions(+), 24 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
index 3ed8c84e25b8..b741b7da1afc 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
@@ -27,6 +27,25 @@ chosen {
stdout-path = "serial0:115200n8";
};
+ wcd938x: codec {
+ compatible = "qcom,wcd9380-codec";
+ #sound-dai-cells = <1>;
+ reset-gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+ vdd-buck-supply = <&vreg_s4a_1p8>;
+ vdd-rxtx-supply = <&vreg_s4a_1p8>;
+ vdd-io-supply = <&vreg_s4a_1p8>;
+ vdd-mic-bias-supply = <&vreg_bob>;
+ qcom,micbias1-microvolt = <1800000>;
+ qcom,micbias2-microvolt = <1800000>;
+ qcom,micbias3-microvolt = <1800000>;
+ qcom,micbias4-microvolt = <1800000>;
+ qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+ qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+ qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+ qcom,rx-device = <&wcd_rx>;
+ qcom,tx-device = <&wcd_tx>;
+ };
+
thermal-zones {
camera-thermal {
polling-delay-passive = <0>;
@@ -631,27 +650,6 @@ &slpi {
firmware-name = "qcom/sm8250/slpi.mbn";
};
-&soc {
- wcd938x: codec {
- compatible = "qcom,wcd9380-codec";
- #sound-dai-cells = <1>;
- reset-gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
- vdd-buck-supply = <&vreg_s4a_1p8>;
- vdd-rxtx-supply = <&vreg_s4a_1p8>;
- vdd-io-supply = <&vreg_s4a_1p8>;
- vdd-mic-bias-supply = <&vreg_bob>;
- qcom,micbias1-microvolt = <1800000>;
- qcom,micbias2-microvolt = <1800000>;
- qcom,micbias3-microvolt = <1800000>;
- qcom,micbias4-microvolt = <1800000>;
- qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
- qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
- qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
- qcom,rx-device = <&wcd_rx>;
- qcom,tx-device = <&wcd_tx>;
- };
-};
-
&sound {
compatible = "qcom,sm8250-sndcard";
model = "SM8250-MTP-WCD9380-WSA8810-VA-DMIC";
diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index d517d6a80bdc..fbbbae29e0c2 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -2826,9 +2826,6 @@ compute-cb@8 {
};
};
- sound: sound {
- };
-
usb_1_hsphy: phy@...3000 {
compatible = "qcom,sm8250-usb-hs-phy",
"qcom,usb-snps-hs-7nm-phy";
@@ -4910,6 +4907,9 @@ cpufreq_hw: cpufreq@...91000 {
};
};
+ sound: sound {
+ };
+
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 13
--
2.34.1
Powered by blists - more mailing lists