Message-Id: <20221214235438.30271-11-ansuelsmth@gmail.com>
Date:   Thu, 15 Dec 2022 00:54:37 +0100
From:   Christian Marangi <ansuelsmth@...il.com>
To:     Andrew Lunn <andrew@...n.ch>,
        Florian Fainelli <f.fainelli@...il.com>,
        Vladimir Oltean <olteanv@...il.com>,
        "David S. Miller" <davem@...emloft.net>,
        Eric Dumazet <edumazet@...gle.com>,
        Jakub Kicinski <kuba@...nel.org>,
        Paolo Abeni <pabeni@...hat.com>,
        Rob Herring <robh+dt@...nel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
        Jonathan Corbet <corbet@....net>, Pavel Machek <pavel@....cz>,
        Christian Marangi <ansuelsmth@...il.com>,
        "Russell King (Oracle)" <rmk+kernel@...linux.org.uk>,
        John Crispin <john@...ozen.org>, netdev@...r.kernel.org,
        devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
        linux-doc@...r.kernel.org, linux-leds@...r.kernel.org,
        Tim Harvey <tharvey@...eworks.com>,
        Alexander Stein <alexander.stein@...tq-group.com>,
        Rasmus Villemoes <rasmus.villemoes@...vas.dk>
Subject: [PATCH v7 10/11] net: dsa: qca8k: add LEDs support

Add LEDs support for qca8k Switch Family. This will provide the LEDs
hardware API to permit the PHY LED to support hardware mode.
Each port have at least 3 LEDs and they can HW blink, set on/off or
follow blink modes configured with the LED in hardware mode.
Adds support for leds netdev trigger to support hardware triggers.

Signed-off-by: Christian Marangi <ansuelsmth@...il.com>
---
 drivers/net/dsa/qca/Kconfig      |   9 +
 drivers/net/dsa/qca/Makefile     |   1 +
 drivers/net/dsa/qca/qca8k-8xxx.c |   4 +
 drivers/net/dsa/qca/qca8k-leds.c | 406 +++++++++++++++++++++++++++++++
 drivers/net/dsa/qca/qca8k.h      |  62 +++++
 5 files changed, 482 insertions(+)
 create mode 100644 drivers/net/dsa/qca/qca8k-leds.c

diff --git a/drivers/net/dsa/qca/Kconfig b/drivers/net/dsa/qca/Kconfig
index ba339747362c..be67164a444e 100644
--- a/drivers/net/dsa/qca/Kconfig
+++ b/drivers/net/dsa/qca/Kconfig
@@ -15,3 +15,12 @@ config NET_DSA_QCA8K
 	help
 	  This enables support for the Qualcomm Atheros QCA8K Ethernet
 	  switch chips.
+
+config NET_DSA_QCA8K_LEDS_SUPPORT
+	tristate "Qualcomm Atheros QCA8K Ethernet switch family LEDs support"
+	depends on NET_DSA_QCA8K
+	select LEDS_OFFLOAD_TRIGGERS
+	help
+	  This enabled support for LEDs present on the Qualcomm Atheros
+	  QCA8K Ethernet switch chips. This require the LEDs offload
+	  triggers support as it can run in offload mode.
diff --git a/drivers/net/dsa/qca/Makefile b/drivers/net/dsa/qca/Makefile
index 701f1d199e93..330ae389e489 100644
--- a/drivers/net/dsa/qca/Makefile
+++ b/drivers/net/dsa/qca/Makefile
@@ -2,3 +2,4 @@
 obj-$(CONFIG_NET_DSA_AR9331)	+= ar9331.o
 obj-$(CONFIG_NET_DSA_QCA8K)	+= qca8k.o
 qca8k-y 			+= qca8k-common.o qca8k-8xxx.o
+obj-$(CONFIG_NET_DSA_QCA8K_LEDS_SUPPORT) += qca8k-leds.o
diff --git a/drivers/net/dsa/qca/qca8k-8xxx.c b/drivers/net/dsa/qca/qca8k-8xxx.c
index c5c3b4e92f28..90916d8d8afe 100644
--- a/drivers/net/dsa/qca/qca8k-8xxx.c
+++ b/drivers/net/dsa/qca/qca8k-8xxx.c
@@ -1690,6 +1690,10 @@ qca8k_setup(struct dsa_switch *ds)
 	if (ret)
 		return ret;
 
+	ret = qca8k_setup_led_ctrl(priv);
+	if (ret)
+		return ret;
+
 	qca8k_setup_pcs(priv, &priv->pcs_port_0, 0);
 	qca8k_setup_pcs(priv, &priv->pcs_port_6, 6);
 
diff --git a/drivers/net/dsa/qca/qca8k-leds.c b/drivers/net/dsa/qca/qca8k-leds.c
new file mode 100644
index 000000000000..b51cdcae31b2
--- /dev/null
+++ b/drivers/net/dsa/qca/qca8k-leds.c
@@ -0,0 +1,406 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <net/dsa.h>
+#include <linux/regmap.h>
+
+#include "qca8k.h"
+
+static int
+qca8k_get_enable_led_reg(int port_num, int led_num, struct qca8k_led_pattern_en *reg_info)
+{
+	int shift;
+
+	switch (port_num) {
+	case 0:
+		reg_info->reg = QCA8K_LED_CTRL_REG(led_num);
+		reg_info->shift = 14;
+		break;
+	case 1:
+	case 2:
+	case 3:
+		reg_info->reg = QCA8K_LED_CTRL_REG(3);
+		shift = 2 * led_num + (6 * (port_num - 1));
+
+		reg_info->shift = 8 + shift;
+
+		break;
+	case 4:
+		reg_info->reg = QCA8K_LED_CTRL_REG(led_num);
+		reg_info->shift = 30;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int
+qca8k_get_control_led_reg(int port_num, int led_num, struct qca8k_led_pattern_en *reg_info)
+{
+	reg_info->reg = QCA8K_LED_CTRL_REG(led_num);
+
+	/* 6 total control rule:
+	 * 3 control rules for phy0-3 that applies to all their leds
+	 * 3 control rules for phy4
+	 */
+	if (port_num == 4)
+		reg_info->shift = 16;
+	else
+		reg_info->shift = 0;
+
+	return 0;
+}
+
+static int
+qca8k_parse_netdev(unsigned long rules, u32 *offload_trigger, u32 *mask)
+{
+	/* Parsing specific to netdev trigger */
+	if (test_bit(TRIGGER_NETDEV_LINK, &rules))
+		*offload_trigger = QCA8K_LED_LINK_10M_EN_MASK |
+				   QCA8K_LED_LINK_100M_EN_MASK |
+				   QCA8K_LED_LINK_1000M_EN_MASK;
+	if (test_bit(TRIGGER_NETDEV_LINK_10, &rules))
+		*offload_trigger = QCA8K_LED_LINK_10M_EN_MASK;
+	if (test_bit(TRIGGER_NETDEV_LINK_100, &rules))
+		*offload_trigger = QCA8K_LED_LINK_100M_EN_MASK;
+	if (test_bit(TRIGGER_NETDEV_LINK_1000, &rules))
+		*offload_trigger = QCA8K_LED_LINK_1000M_EN_MASK;
+	if (test_bit(TRIGGER_NETDEV_HALF_DUPLEX, &rules))
+		*offload_trigger = QCA8K_LED_HALF_DUPLEX_MASK;
+	if (test_bit(TRIGGER_NETDEV_FULL_DUPLEX, &rules))
+		*offload_trigger = QCA8K_LED_FULL_DUPLEX_MASK;
+	if (test_bit(TRIGGER_NETDEV_TX, &rules))
+		*offload_trigger = QCA8K_LED_TX_BLINK_MASK;
+	if (test_bit(TRIGGER_NETDEV_RX, &rules))
+		*offload_trigger = QCA8K_LED_RX_BLINK_MASK;
+	if (test_bit(TRIGGER_NETDEV_BLINK_2HZ, &rules))
+		*offload_trigger = QCA8K_LED_BLINK_2HZ;
+	if (test_bit(TRIGGER_NETDEV_BLINK_4HZ, &rules))
+		*offload_trigger = QCA8K_LED_BLINK_4HZ;
+	if (test_bit(TRIGGER_NETDEV_BLINK_8HZ, &rules))
+		*offload_trigger = QCA8K_LED_BLINK_8HZ;
+
+	if (!*offload_trigger)
+		return -EOPNOTSUPP;
+
+	if (test_bit(TRIGGER_NETDEV_BLINK_2HZ, &rules) ||
+	    test_bit(TRIGGER_NETDEV_BLINK_4HZ, &rules) ||
+	    test_bit(TRIGGER_NETDEV_BLINK_8HZ, &rules)) {
+		*mask = QCA8K_LED_BLINK_FREQ_MASK;
+	} else {
+		*mask = *offload_trigger;
+	}
+
+	return 0;
+}
+
+static int
+qca8k_cled_hw_control_configure(struct led_classdev *ldev, unsigned long rules,
+				enum blink_mode_cmd cmd)
+{
+	struct qca8k_led *led = container_of(ldev, struct qca8k_led, cdev);
+	struct led_trigger *trigger = ldev->trigger;
+	struct qca8k_led_pattern_en reg_info;
+	struct qca8k_priv *priv = led->priv;
+	u32 offload_trigger = 0, mask, val;
+	int ret;
+
+	/* Check trigger compatibility */
+	if (strcmp(trigger->name, "netdev"))
+		return -EOPNOTSUPP;
+
+	if (!strcmp(trigger->name, "netdev"))
+		ret = qca8k_parse_netdev(rules, &offload_trigger, &mask);
+
+	if (ret)
+		return ret;
+
+	qca8k_get_control_led_reg(led->port_num, led->led_num, &reg_info);
+
+	switch (cmd) {
+	case BLINK_MODE_SUPPORTED:
+		/* We reach this point, we are sure the trigger is supported */
+		return 1;
+	case BLINK_MODE_ZERO:
+		/* We set 4hz by default */
+		u32 default_reg = QCA8K_LED_BLINK_4HZ;
+
+		ret = regmap_update_bits(priv->regmap, reg_info.reg,
+					 QCA8K_LED_RULE_MASK << reg_info.shift,
+					 default_reg << reg_info.shift);
+		break;
+	case BLINK_MODE_ENABLE:
+		ret = regmap_update_bits(priv->regmap, reg_info.reg,
+					 mask << reg_info.shift,
+					 offload_trigger << reg_info.shift);
+		break;
+	case BLINK_MODE_DISABLE:
+		ret = regmap_update_bits(priv->regmap, reg_info.reg,
+					 mask << reg_info.shift,
+					 0);
+		break;
+	case BLINK_MODE_READ:
+		ret = regmap_read(priv->regmap, reg_info.reg, &val);
+		if (ret)
+			return ret;
+
+		val >>= reg_info.shift;
+		val &= offload_trigger;
+
+		/* Special handling for LED_BLINK_2HZ */
+		if (!val && offload_trigger == QCA8K_LED_BLINK_2HZ)
+			val = 1;
+
+		return val;
+	default:
+		return -EOPNOTSUPP;
+	}
+
+	return ret;
+}
+
+static void
+qca8k_led_brightness_set(struct qca8k_led *led,
+			 enum led_brightness b)
+{
+	struct qca8k_led_pattern_en reg_info;
+	struct qca8k_priv *priv = led->priv;
+	u32 val = QCA8K_LED_ALWAYS_OFF;
+
+	qca8k_get_enable_led_reg(led->port_num, led->led_num, &reg_info);
+
+	if (b)
+		val = QCA8K_LED_ALWAYS_ON;
+
+	regmap_update_bits(priv->regmap, reg_info.reg,
+			   GENMASK(1, 0) << reg_info.shift,
+			   val << reg_info.shift);
+}
+
+static void
+qca8k_cled_brightness_set(struct led_classdev *ldev,
+			  enum led_brightness b)
+{
+	struct qca8k_led *led = container_of(ldev, struct qca8k_led, cdev);
+
+	return qca8k_led_brightness_set(led, b);
+}
+
+static enum led_brightness
+qca8k_led_brightness_get(struct qca8k_led *led)
+{
+	struct qca8k_led_pattern_en reg_info;
+	struct qca8k_priv *priv = led->priv;
+	u32 val;
+	int ret;
+
+	qca8k_get_enable_led_reg(led->port_num, led->led_num, &reg_info);
+
+	ret = regmap_read(priv->regmap, reg_info.reg, &val);
+	if (ret)
+		return 0;
+
+	val >>= reg_info.shift;
+	val &= GENMASK(1, 0);
+
+	return val > 0 ? 1 : 0;
+}
+
+static enum led_brightness
+qca8k_cled_brightness_get(struct led_classdev *ldev)
+{
+	struct qca8k_led *led = container_of(ldev, struct qca8k_led, cdev);
+
+	return qca8k_led_brightness_get(led);
+}
+
+static int
+qca8k_cled_blink_set(struct led_classdev *ldev,
+		     unsigned long *delay_on,
+		     unsigned long *delay_off)
+{
+	struct qca8k_led *led = container_of(ldev, struct qca8k_led, cdev);
+	struct qca8k_led_pattern_en reg_info;
+	struct qca8k_priv *priv = led->priv;
+
+	if (*delay_on == 0 && *delay_off == 0) {
+		*delay_on = 125;
+		*delay_off = 125;
+	}
+
+	if (*delay_on != 125 || *delay_off != 125) {
+		/* The hardware only supports blinking at 4Hz. Fall back
+		 * to software implementation in other cases.
+		 */
+		return -EINVAL;
+	}
+
+	qca8k_get_enable_led_reg(led->port_num, led->led_num, &reg_info);
+
+	regmap_update_bits(priv->regmap, reg_info.reg,
+			   GENMASK(1, 0) << reg_info.shift,
+			   QCA8K_LED_ALWAYS_BLINK_4HZ << reg_info.shift);
+
+	return 0;
+}
+
+static int
+qca8k_cled_trigger_offload(struct led_classdev *ldev, bool enable)
+{
+	struct qca8k_led *led = container_of(ldev, struct qca8k_led, cdev);
+
+	struct qca8k_led_pattern_en reg_info;
+	struct qca8k_priv *priv = led->priv;
+	u32 val = QCA8K_LED_ALWAYS_OFF;
+
+	qca8k_get_enable_led_reg(led->port_num, led->led_num, &reg_info);
+
+	if (enable)
+		val = QCA8K_LED_RULE_CONTROLLED;
+
+	return regmap_update_bits(priv->regmap, reg_info.reg,
+				  GENMASK(1, 0) << reg_info.shift,
+				  val << reg_info.shift);
+}
+
+static int
+qca8k_cled_hw_control_start(struct led_classdev *led_cdev)
+{
+	return qca8k_cled_trigger_offload(led_cdev, true);
+}
+
+static int
+qca8k_cled_hw_control_stop(struct led_classdev *led_cdev)
+{
+	return qca8k_cled_trigger_offload(led_cdev, false);
+}
+
+static bool
+qca8k_cled_hw_control_status(struct led_classdev *ldev)
+{
+	struct qca8k_led *led = container_of(ldev, struct qca8k_led, cdev);
+
+	struct qca8k_led_pattern_en reg_info;
+	struct qca8k_priv *priv = led->priv;
+	u32 val;
+
+	qca8k_get_enable_led_reg(led->port_num, led->led_num, &reg_info);
+
+	regmap_read(priv->regmap, reg_info.reg, &val);
+
+	val >>= reg_info.shift;
+	val &= GENMASK(1, 0);
+
+	return val == QCA8K_LED_RULE_CONTROLLED;
+}
+
+static int
+qca8k_parse_port_leds(struct qca8k_priv *priv, struct fwnode_handle *port, int port_num)
+{
+	struct fwnode_handle *led = NULL, *leds = NULL;
+	struct led_init_data init_data = { };
+	struct qca8k_led *port_led;
+	int led_num, port_index;
+	const char *state;
+	int ret;
+
+	leds = fwnode_get_named_child_node(port, "leds");
+	if (!leds) {
+		dev_dbg(priv->dev, "No Leds node specified in device tree for port %d!\n",
+			port_num);
+		return 0;
+	}
+
+	fwnode_for_each_child_node(leds, led) {
+		/* Reg represent the led number of the port.
+		 * Each port can have at least 3 leds attached
+		 * Commonly:
+		 * 1. is gigabit led
+		 * 2. is mbit led
+		 * 3. additional status led
+		 */
+		if (fwnode_property_read_u32(led, "reg", &led_num))
+			continue;
+
+		if (led_num >= QCA8K_LED_PORT_COUNT) {
+			dev_warn(priv->dev, "Invalid LED reg defined %d", port_num);
+			continue;
+		}
+
+		port_index = 3 * port_num + led_num;
+
+		port_led = &priv->ports_led[port_index];
+		port_led->port_num = port_num;
+		port_led->led_num = led_num;
+		port_led->priv = priv;
+
+		ret = fwnode_property_read_string(led, "default-state", &state);
+		if (!ret) {
+			if (!strcmp(state, "on")) {
+				port_led->cdev.brightness = 1;
+				qca8k_led_brightness_set(port_led, 1);
+			} else if (!strcmp(state, "off")) {
+				port_led->cdev.brightness = 0;
+				qca8k_led_brightness_set(port_led, 0);
+			} else if (!strcmp(state, "keep")) {
+				port_led->cdev.brightness =
+					qca8k_led_brightness_get(port_led);
+			}
+		}
+
+		/* 3 brightness settings can be applied from Documentation:
+		 * 0 always off
+		 * 1 blink at 4Hz
+		 * 2 always on
+		 * 3 rule controlled
+		 * Suppots only 2 mode: (pcb limitation, with always on and blink
+		 * only the last led is set to this mode)
+		 * 0 always off (sets all leds off)
+		 * 3 rule controlled
+		 */
+		port_led->cdev.blink_mode = SOFTWARE_HARDWARE_CONTROLLED;
+		port_led->cdev.max_brightness = 1;
+		port_led->cdev.brightness_set = qca8k_cled_brightness_set;
+		port_led->cdev.brightness_get = qca8k_cled_brightness_get;
+		port_led->cdev.blink_set = qca8k_cled_blink_set;
+		port_led->cdev.hw_control_start = qca8k_cled_hw_control_start;
+		port_led->cdev.hw_control_stop = qca8k_cled_hw_control_stop;
+		port_led->cdev.hw_control_status = qca8k_cled_hw_control_status;
+		port_led->cdev.hw_control_configure = qca8k_cled_hw_control_configure;
+		init_data.default_label = ":port";
+		init_data.devicename = "qca8k";
+		init_data.fwnode = led;
+
+		ret = devm_led_classdev_register_ext(priv->dev, &port_led->cdev, &init_data);
+		if (ret)
+			dev_warn(priv->dev, "Failed to int led");
+	}
+
+	return 0;
+}
+
+int
+qca8k_setup_led_ctrl(struct qca8k_priv *priv)
+{
+	struct fwnode_handle *mdio, *port;
+	int port_num;
+	int ret;
+
+	mdio = device_get_named_child_node(priv->dev, "mdio");
+	if (!mdio) {
+		dev_info(priv->dev, "No MDIO node specified in device tree!\n");
+		return 0;
+	}
+
+	fwnode_for_each_child_node(mdio, port) {
+		if (fwnode_property_read_u32(port, "reg", &port_num))
+			continue;
+
+		/* Each port can have at least 3 different leds attached */
+		ret = qca8k_parse_port_leds(priv, port, port_num);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
diff --git a/drivers/net/dsa/qca/qca8k.h b/drivers/net/dsa/qca/qca8k.h
index 0b7a5cb12321..5c535baa7139 100644
--- a/drivers/net/dsa/qca/qca8k.h
+++ b/drivers/net/dsa/qca/qca8k.h
@@ -11,6 +11,7 @@
 #include <linux/delay.h>
 #include <linux/regmap.h>
 #include <linux/gpio.h>
+#include <linux/leds.h>
 #include <linux/dsa/tag_qca.h>
 
 #define QCA8K_ETHERNET_MDIO_PRIORITY			7
@@ -85,6 +86,43 @@
 #define   QCA8K_MDIO_MASTER_DATA(x)			FIELD_PREP(QCA8K_MDIO_MASTER_DATA_MASK, x)
 #define   QCA8K_MDIO_MASTER_MAX_PORTS			5
 #define   QCA8K_MDIO_MASTER_MAX_REG			32
+
+/* LED control register */
+#define QCA8K_LED_COUNT					15
+#define QCA8K_LED_PORT_COUNT				3
+#define QCA8K_LED_RULE_COUNT				6
+#define QCA8K_LED_RULE_MAX				11
+#define QCA8K_LED_CTRL_REG(_i)				(0x050 + (_i) * 4)
+#define QCA8K_LED_CTRL0_REG				0x50
+#define QCA8K_LED_CTRL1_REG				0x54
+#define QCA8K_LED_CTRL2_REG				0x58
+#define QCA8K_LED_CTRL3_REG				0x5C
+#define   QCA8K_LED_CTRL_SHIFT(_i)			(((_i) % 2) * 16)
+#define   QCA8K_LED_CTRL_MASK				GENMASK(15, 0)
+#define QCA8K_LED_RULE_MASK				GENMASK(13, 0)
+#define QCA8K_LED_BLINK_FREQ_MASK			GENMASK(1, 0)
+#define QCA8K_LED_BLINK_FREQ_SHITF			0
+#define   QCA8K_LED_BLINK_2HZ				0
+#define   QCA8K_LED_BLINK_4HZ				1
+#define   QCA8K_LED_BLINK_8HZ				2
+#define   QCA8K_LED_BLINK_AUTO				3
+#define QCA8K_LED_LINKUP_OVER_MASK			BIT(2)
+#define QCA8K_LED_TX_BLINK_MASK				BIT(4)
+#define QCA8K_LED_RX_BLINK_MASK				BIT(5)
+#define QCA8K_LED_COL_BLINK_MASK			BIT(7)
+#define QCA8K_LED_LINK_10M_EN_MASK			BIT(8)
+#define QCA8K_LED_LINK_100M_EN_MASK			BIT(9)
+#define QCA8K_LED_LINK_1000M_EN_MASK			BIT(10)
+#define QCA8K_LED_POWER_ON_LIGHT_MASK			BIT(11)
+#define QCA8K_LED_HALF_DUPLEX_MASK			BIT(12)
+#define QCA8K_LED_FULL_DUPLEX_MASK			BIT(13)
+#define QCA8K_LED_PATTERN_EN_MASK			GENMASK(15, 14)
+#define QCA8K_LED_PATTERN_EN_SHIFT			14
+#define   QCA8K_LED_ALWAYS_OFF				0
+#define   QCA8K_LED_ALWAYS_BLINK_4HZ			1
+#define   QCA8K_LED_ALWAYS_ON				2
+#define   QCA8K_LED_RULE_CONTROLLED			3
+
 #define QCA8K_GOL_MAC_ADDR0				0x60
 #define QCA8K_GOL_MAC_ADDR1				0x64
 #define QCA8K_MAX_FRAME_SIZE				0x78
@@ -388,6 +426,19 @@ struct qca8k_pcs {
 	int port;
 };
 
+struct qca8k_led_pattern_en {
+	u32 reg;
+	u8 shift;
+};
+
+struct qca8k_led {
+	u8 port_num;
+	u8 led_num;
+	u16 old_rule;
+	struct qca8k_priv *priv;
+	struct led_classdev cdev;
+};
+
 struct qca8k_priv {
 	u8 switch_id;
 	u8 switch_revision;
@@ -412,6 +463,7 @@ struct qca8k_priv {
 	struct qca8k_pcs pcs_port_0;
 	struct qca8k_pcs pcs_port_6;
 	const struct qca8k_match_data *info;
+	struct qca8k_led ports_led[QCA8K_LED_COUNT];
 };
 
 struct qca8k_mib_desc {
@@ -517,4 +569,14 @@ int qca8k_port_lag_join(struct dsa_switch *ds, int port, struct dsa_lag lag,
 int qca8k_port_lag_leave(struct dsa_switch *ds, int port,
 			 struct dsa_lag lag);
 
+/* Leds Support function */
+#ifdef CONFIG_NET_DSA_QCA8K_LEDS_SUPPORT
+int qca8k_setup_led_ctrl(struct qca8k_priv *priv);
+#else
+static inline int qca8k_setup_led_ctrl(struct qca8k_priv *priv)
+{
+	return 0;
+}
+#endif
+
 #endif /* __QCA8K_H */
-- 
2.37.2

Powered by blists - more mailing lists