| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <50d236ae-c3b7-70fc-f699-5ac9c9939b3f@microchip.com>
Date: Fri, 16 Dec 2022 09:38:28 +0000
From: <Claudiu.Beznea@...rochip.com>
To: <Durai.ManickamKR@...rochip.com>, <Hari.PrasathGE@...rochip.com>,
<Balamanikandan.Gunasundar@...rochip.com>,
<Manikandan.M@...rochip.com>, <Varshini.Rajendran@...rochip.com>,
<Dharma.B@...rochip.com>, <Cristian.Birsan@...rochip.com>,
<Nicolas.Ferre@...rochip.com>, <krzysztof.kozlowski@...aro.org>,
<alexandre.belloni@...tlin.com>, <davem@...emloft.net>,
<arnd@...db.de>, <olof@...om.net>, <soc@...nel.org>,
<devicetree@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-kernel@...r.kernel.org>, <Kavyasree.Kotagiri@...rochip.com>,
<Horatiu.Vultur@...rochip.com>, <robh+dt@...nel.org>,
<andrew@...n.ch>, <michael@...le.cc>, <Jerry.Ray@...rochip.com>
Subject: Re: [PATCH v3 2/8] ARM: dts: at91: sam9x60: move flexcom definitions
On 13.12.2022 14:06, Durai Manickam KR wrote:
> From: Manikandan Muralidharan <manikandan.m@...rochip.com>
>
> Move the flexcom definitions from board specific DTS file
> to the SoC specific DTSI file for sam9x60ek.
>
> Signed-off-by: Manikandan Muralidharan <manikandan.m@...rochip.com>
> Signed-off-by: Hari Prasath Gujulan Elango <Hari.PrasathGE@...rochip.com>
> [durai.manickamkr@...rochip.com: Logical split-up of this patch]
> Signed-off-by: Durai Manickam KR <durai.manickamkr@...rochip.com>
> ---
> arch/arm/boot/dts/at91-sam9x60ek.dts | 33 +-----------------
> arch/arm/boot/dts/sam9x60.dtsi | 50 ++++++++++++++++++++++++++++
> 2 files changed, 51 insertions(+), 32 deletions(-)
>
> diff --git a/arch/arm/boot/dts/at91-sam9x60ek.dts b/arch/arm/boot/dts/at91-sam9x60ek.dts
> index cf5d786531f2..4ff84633dd43 100644
> --- a/arch/arm/boot/dts/at91-sam9x60ek.dts
> +++ b/arch/arm/boot/dts/at91-sam9x60ek.dts
> @@ -207,15 +207,10 @@ &flx0 {
> status = "okay";
>
> i2c0: i2c@600 {
> - compatible = "microchip,sam9x60-i2c";
> - reg = <0x600 0x200>;
> - interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
> #address-cells = <1>;
> #size-cells = <0>;
> - clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_flx0_default>;
> - atmel,fifo-size = <16>;
> i2c-analog-filter;
> i2c-digital-filter;
> i2c-digital-filter-width-ns = <35>;
> @@ -235,14 +230,8 @@ &flx4 {
> status = "disabled";
>
> spi4: spi@400 {
> - compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
> - reg = <0x400 0x200>;
> - interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
> - clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
> - clock-names = "spi_clk";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_flx4_default>;
> - atmel,fifo-size = <16>;
> #address-cells = <1>;
> #size-cells = <0>;
> status = "disabled";
> @@ -254,23 +243,8 @@ &flx5 {
> status = "okay";
>
> uart5: serial@200 {
> - compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
> - reg = <0x200 0x200>;
> - atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
You lost this property. Now it is not present neither in dts nor in dtsi.
> - interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
> - dmas = <&dma0
> - (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> - AT91_XDMAC_DT_PERID(10))>,
> - <&dma0
> - (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> - AT91_XDMAC_DT_PERID(11))>;
> - dma-names = "tx", "rx";
> - clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
> - clock-names = "usart";
> - pinctrl-0 = <&pinctrl_flx5_default>;
> pinctrl-names = "default";
> - atmel,use-dma-rx;
> - atmel,use-dma-tx;
> + pinctrl-0 = <&pinctrl_flx5_default>;
> status = "okay";
> };
> };
> @@ -280,15 +254,10 @@ &flx6 {
> status = "okay";
>
> i2c6: i2c@600 {
> - compatible = "microchip,sam9x60-i2c";
> - reg = <0x600 0x200>;
> - interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
> #address-cells = <1>;
> #size-cells = <0>;
> - clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_flx6_default>;
> - atmel,fifo-size = <16>;
> i2c-analog-filter;
> i2c-digital-filter;
> i2c-digital-filter-width-ns = <35>;
> diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
> index 8f5477e307dd..9a5dcf8a2b74 100644
> --- a/arch/arm/boot/dts/sam9x60.dtsi
> +++ b/arch/arm/boot/dts/sam9x60.dtsi
> @@ -170,6 +170,16 @@ flx4: flexcom@...00000 {
> #size-cells = <1>;
> ranges = <0x0 0xf0000000 0x800>;
> status = "disabled";
> +
> + spi4: spi@400 {
> + compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
> + reg = <0x400 0x200>;
> + interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
> + clock-names = "spi_clk";
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> };
>
> flx5: flexcom@...04000 {
> @@ -180,6 +190,26 @@ flx5: flexcom@...04000 {
> #size-cells = <1>;
> ranges = <0x0 0xf0004000 0x800>;
> status = "disabled";
> +
> + uart5: serial@200 {
> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> + reg = <0x200 0x200>;
> + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(10))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(11))>;
> + dma-names = "tx", "rx";
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
> + clock-names = "usart";
> + atmel,use-dma-rx;
> + atmel,use-dma-tx;
> + status = "disabled";
> + };
> };
>
> dma0: dma-controller@...08000 {
> @@ -379,6 +409,15 @@ flx6: flexcom@...10000 {
> #size-cells = <1>;
> ranges = <0x0 0xf8010000 0x800>;
> status = "disabled";
> +
> + i2c6: i2c@600 {
> + compatible = "microchip,sam9x60-i2c";
> + reg = <0x600 0x200>;
> + interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> };
>
> flx7: flexcom@...14000 {
> @@ -409,6 +448,17 @@ flx0: flexcom@...1c000 {
> #size-cells = <1>;
> ranges = <0x0 0xf801c000 0x800>;
> status = "disabled";
> +
> + i2c0: i2c@600 {
> + compatible = "microchip,sam9x60-i2c";
> + reg = <0x600 0x200>;
> + interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
> + #address-cells = <1>;
> + #size-cells = <0>;
You also added #address-cells, #size-cells. These are also present in board
dts and should stay there. Thus you can get rid of these 2 here.
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> };
>
> flx1: flexcom@...20000 {
Powered by blists - more mailing lists