| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <d8e5fccc-4674-6576-924f-3237f55d16c1@linaro.org>
Date: Tue, 3 Jan 2023 03:16:20 +0100
From: Konrad Dybcio <konrad.dybcio@...aro.org>
To: Bryan O'Donoghue <bryan.odonoghue@...aro.org>, agross@...nel.org,
andersson@...nel.org, djakov@...nel.org, robh+dt@...nel.org,
krzysztof.kozlowski+dt@...aro.org
Cc: linux-arm-msm@...r.kernel.org, linux-pm@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
benl@...areup.com, shawn.guo@...aro.org, fabien.parent@...aro.org,
leo.yan@...aro.org, dmitry.baryshkov@...aro.org,
Jun Nie <jun.nie@...aro.org>,
James Willcox <jwillcox@...areup.com>,
Joseph Gates <jgates@...areup.com>,
Max Chen <mchen@...areup.com>, Zac Crosby <zac@...areup.com>,
Vincent Knecht <vincent.knecht@...loo.org>,
Stephan Gerhold <stephan@...hold.net>
Subject: Re: [PATCH v2 4/7] arm64: dts: qcom: Add msm8939 SoC
On 3.01.2023 02:09, Bryan O'Donoghue wrote:
> Add msm8939 a derivative SoC of msm8916. This SoC contains a number of key
> differences to msm8916.
>
> - big.LITTLE Octa Core - quad 1.5GHz + quad 1.0GHz
> - DRAM 1x800 LPDDR3
> - Camera 4+4 lane CSI
> - Venus @ 1080p60 HEVC
> - DSI x 2
> - Adreno A405
> - WiFi wcn3660/wcn3680b 802.11ac
>
> Co-developed-by: Shawn Guo <shawn.guo@...aro.org>
> Signed-off-by: Shawn Guo <shawn.guo@...aro.org>
> Co-developed-by: Jun Nie <jun.nie@...aro.org>
> Signed-off-by: Jun Nie <jun.nie@...aro.org>
> Co-developed-by: Benjamin Li <benl@...areup.com>
> Signed-off-by: Benjamin Li <benl@...areup.com>
> Co-developed-by: James Willcox <jwillcox@...areup.com>
> Signed-off-by: James Willcox <jwillcox@...areup.com>
> Co-developed-by: Leo Yan <leo.yan@...aro.org>
> Signed-off-by: Leo Yan <leo.yan@...aro.org>
> Co-developed-by: Joseph Gates <jgates@...areup.com>
> Signed-off-by: Joseph Gates <jgates@...areup.com>
> Co-developed-by: Max Chen <mchen@...areup.com>
> Signed-off-by: Max Chen <mchen@...areup.com>
> Co-developed-by: Zac Crosby <zac@...areup.com>
> Signed-off-by: Zac Crosby <zac@...areup.com>
> Co-developed-by: Vincent Knecht <vincent.knecht@...loo.org>
> Signed-off-by: Vincent Knecht <vincent.knecht@...loo.org>
> Co-developed-by: Stephan Gerhold <stephan@...hold.net>
> Signed-off-by: Stephan Gerhold <stephan@...hold.net>
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@...aro.org>
I'm mesmerized by the size of this list..
> ---
> arch/arm64/boot/dts/qcom/msm8939.dtsi | 2470 +++++++++++++++++++++++++
> 1 file changed, 2470 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/msm8939.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/msm8939.dtsi b/arch/arm64/boot/dts/qcom/msm8939.dtsi
> new file mode 100644
> index 0000000000000..03714cdb8b69e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8939.dtsi
> @@ -0,0 +1,2470 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2013-2015, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2020-2023, Linaro Limited
> + */
> +
> +#include <dt-bindings/clock/qcom,gcc-msm8939.h>
> +#include <dt-bindings/clock/qcom,rpmcc.h>
> +#include <dt-bindings/interconnect/qcom,msm8939.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/power/qcom-rpmpd.h>
> +#include <dt-bindings/reset/qcom,gcc-msm8939.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +/ {
> + qcom,msm-id = <239 0>, <239 0x30000>, <241 0x30000>, <263 0x30000>;
Nowadays we put msm-id in device DTs. Also, is <239 0> (v0) valid?
> +
> + interrupt-parent = <&intc>;
> +
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + aliases {
> + mmc0 = &sdhc_1; /* SDC1 eMMC slot */
> + mmc1 = &sdhc_2; /* SDC2 SD card slot */
> + };
> +
> + clocks {
> + xo_board: xo-board {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <19200000>;
> + clock-output-names = "xo_board";
We keep clock-output-names for legacy DTs. Please feed "xo"
to rpmcc and remove this.
> + };
> +
> + sleep_clk: sleep-clk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + clock-output-names = "sleep_clk";
> + };
> + };
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu0: cpu@100 {
> + compatible = "arm,cortex-a53";
> + device_type = "cpu";
> + enable-method = "spin-table";
Is cpu-release-addr added dynamically?
> + reg = <0x100>;
> + next-level-cache = <&L2_1>;
> + power-domains = <&vreg_dummy>;
> + power-domain-names = "cpr";
> + qcom,acc = <&acc0>;
> + qcom,saw = <&saw0>;
> + cpu-idle-states = <&CPU_SLEEP_0>;
> + clocks = <&apcs1_mbox>;
> + #cooling-cells = <2>;
> + L2_1: l2-cache@1 {
> + compatible = "cache";
> + cache-level = <2>;
> + };
> + };
> +
> + cpu1: cpu@101 {
> + compatible = "arm,cortex-a53";
> + device_type = "cpu";
> + enable-method = "spin-table";
> + reg = <0x101>;
> + next-level-cache = <&L2_1>;
> + power-domains = <&vreg_dummy>;
> + power-domain-names = "cpr";
> + qcom,acc = <&acc1>;
> + qcom,saw = <&saw1>;
> + cpu-idle-states = <&CPU_SLEEP_0>;
> + clocks = <&apcs1_mbox>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu2: cpu@102 {
> + compatible = "arm,cortex-a53";
> + device_type = "cpu";
> + enable-method = "spin-table";
> + reg = <0x102>;
> + next-level-cache = <&L2_1>;
> + power-domains = <&vreg_dummy>;
> + power-domain-names = "cpr";
> + qcom,acc = <&acc2>;
> + qcom,saw = <&saw2>;
> + cpu-idle-states = <&CPU_SLEEP_0>;
> + clocks = <&apcs1_mbox>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu3: cpu@103 {
> + compatible = "arm,cortex-a53";
> + device_type = "cpu";
> + enable-method = "spin-table";
> + reg = <0x103>;
> + next-level-cache = <&L2_1>;
> + power-domains = <&vreg_dummy>;
> + power-domain-names = "cpr";
> + qcom,acc = <&acc3>;
> + qcom,saw = <&saw3>;
> + cpu-idle-states = <&CPU_SLEEP_0>;
> + clocks = <&apcs1_mbox>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu4: cpu@0 {
> + compatible = "arm,cortex-a53";
> + device_type = "cpu";
> + enable-method = "spin-table";
> + reg = <0x0>;
> + qcom,acc = <&acc4>;
> + qcom,saw = <&saw4>;
> + cpu-idle-states = <&CPU_SLEEP_0>;
> + clocks = <&apcs0_mbox>;
> + #cooling-cells = <2>;
> + next-level-cache = <&L2_0>;
> + power-domains = <&vreg_dummy>;
> + power-domain-names = "cpr";
> + L2_0: l2-cache@0 {
> + compatible = "cache";
> + cache-level = <2>;
> + };
> + };
> +
> + cpu5: cpu@1 {
> + compatible = "arm,cortex-a53";
> + device_type = "cpu";
> + enable-method = "spin-table";
> + reg = <0x1>;
> + next-level-cache = <&L2_0>;
> + power-domains = <&vreg_dummy>;
> + power-domain-names = "cpr";
> + qcom,acc = <&acc5>;
> + qcom,saw = <&saw5>;
> + cpu-idle-states = <&CPU_SLEEP_0>;
> + clocks = <&apcs0_mbox>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu6: cpu@2 {
> + compatible = "arm,cortex-a53";
> + device_type = "cpu";
> + enable-method = "spin-table";
> + reg = <0x2>;
> + next-level-cache = <&L2_0>;
> + power-domains = <&vreg_dummy>;
> + power-domain-names = "cpr";
> + qcom,acc = <&acc6>;
> + qcom,saw = <&saw6>;
> + cpu-idle-states = <&CPU_SLEEP_0>;
> + clocks = <&apcs0_mbox>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu7: cpu@3 {
> + compatible = "arm,cortex-a53";
> + device_type = "cpu";
> + enable-method = "spin-table";
> + reg = <0x3>;
> + next-level-cache = <&L2_0>;
> + power-domains = <&vreg_dummy>;
> + power-domain-names = "cpr";
> + qcom,acc = <&acc7>;
> + qcom,saw = <&saw7>;
> + cpu-idle-states = <&CPU_SLEEP_0>;
> + clocks = <&apcs0_mbox>;
> + #cooling-cells = <2>;
> + };
> +
> + idle-states {
> + CPU_SLEEP_0: cpu-sleep-0 {
> + compatible ="qcom,idle-state-spc", "arm,idle-state";
> + entry-latency-us = <130>;
> + exit-latency-us = <150>;
> + min-residency-us = <2000>;
> + local-timer-stop;
> + };
> + };
> + };
> +
> + /*
> + * MSM8939 has a big.LITTLE heterogeneous computing architecture,
> + * consisting of two clusters of four ARM Cortex-A53s each. The
> + * LITTLE cluster runs at 1.0-1.2GHz, and the big cluster runs
> + * at 1.5-1.7GHz.
> + *
> + * The enable method used here is spin-table which presupposes use
> + * of a 2nd stage boot shim such as lk2nd to have installed a
> + * spin-table, the downstream non-psci/non-spin-table method that
> + * default msm8916/msm8936/msm8939 will not be supported upstream.
> + */
> + cpu-map {
> + /* LITTLE (efficiency) cluster */
> + cluster0 {
> + core0 {
> + cpu = <&cpu4>;
> + };
> +
> + core1 {
> + cpu = <&cpu5>;
> + };
> +
> + core2 {
> + cpu = <&cpu6>;
> + };
> +
> + core3 {
> + cpu = <&cpu7>;
> + };
> + };
> +
> + /* big (performance) cluster */
> + /* Boot CPU is cluster 1 core 0 */
cpu0 is expected to be the boot cpu.. That said, we can
keep this comment if you wish.
> + cluster1 {
> + core0 {
> + cpu = <&cpu0>;
> + };
> +
> + core1 {
> + cpu = <&cpu1>;
> + };
> +
> + core2 {
> + cpu = <&cpu2>;
> + };
> +
> + core3 {
> + cpu = <&cpu3>;
> + };
> + };
> + };
> +
> + firmware {
> + scm: scm {
> + compatible = "qcom,scm-msm8916", "qcom,scm";
> + clocks = <&gcc GCC_CRYPTO_CLK>,
> + <&gcc GCC_CRYPTO_AXI_CLK>,
> + <&gcc GCC_CRYPTO_AHB_CLK>;
> + clock-names = "core", "bus", "iface";
> + #reset-cells = <1>;
> +
> + qcom,dload-mode = <&tcsr 0x6100>;
> + };
> + };
> +
> + hexagon-smp2p {
> + compatible = "qcom,smp2p";
> + qcom,smem = <435>, <428>;
> +
> + interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
> +
> + mboxes = <&apcs1_mbox 14>;
> +
> + qcom,local-pid = <0>;
> + qcom,remote-pid = <1>;
> +
> + hexagon_smp2p_out: master-kernel {
> + qcom,entry-name = "master-kernel";
> +
> + #qcom,smem-state-cells = <1>;
> + };
> +
> + hexagon_smp2p_in: slave-kernel {
> + qcom,entry-name = "slave-kernel";
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + memory@...00000 {
> + device_type = "memory";
> + /* We expect the bootloader to fill in the reg */
> + reg = <0x0 0x80000000 0x0 0x0>;
> + };
> +
> + pmu {
> + compatible = "arm,cortex-a53-pmu";
> + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(8)| IRQ_TYPE_LEVEL_HIGH)>;
Missing space before |
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + tz-apps@...00000 {
> + reg = <0x0 0x86000000 0x0 0x300000>;
> + no-map;
> + };
> +
> + smem_mem: smem@...00000 {
> + reg = <0x0 0x86300000 0x0 0x100000>;
> + no-map;
> + };
> +
> + hypervisor@...00000 {
> + reg = <0x0 0x86400000 0x0 0x100000>;
> + no-map;
> + };
> +
> + tz@...00000 {
> + reg = <0x0 0x86500000 0x0 0x180000>;
> + no-map;
> + };
> +
> + reserved@...80000 {
> + reg = <0x0 0x86680000 0x0 0x80000>;
> + no-map;
> + };
> +
> + rmtfs@...00000 {
> + compatible = "qcom,rmtfs-mem";
> + reg = <0x0 0x86700000 0x0 0xe0000>;
> + no-map;
> +
> + qcom,client-id = <1>;
> + };
> +
> + rfsa@...e0000 {
> + reg = <0x0 0x867e0000 0x0 0x20000>;
> + no-map;
> + };
> +
> + mpss_mem: mpss@...00000 {
> + reg = <0x0 0x86800000 0x0 0x5500000>;
> + no-map;
> + };
> +
> + wcnss_mem: wcnss@...00000 {
> + reg = <0x0 0x8bd00000 0x0 0x600000>;
> + no-map;
> + };
> +
> + venus_mem: venus@...00000 {
> + reg = <0x0 0x8c300000 0x0 0x800000>;
> + no-map;
> + };
> +
> + mba_mem: mba@...00000 {
> + no-map;
> + reg = <0x0 0x8cb00000 0x0 0x100000>;
> + };
> + };
> +
> + smem {
> + compatible = "qcom,smem";
smem is now expected to be a child of reserved-memory (there's
a new binding).
> +
> + memory-region = <&smem_mem>;
> + qcom,rpm-msg-ram = <&rpm_msg_ram>;
> +
> + hwlocks = <&tcsr_mutex 3>;
> + };
> +
> + smsm {
> + compatible = "qcom,smsm";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + qcom,ipc-1 = <&apcs1_mbox 8 13>;
> + qcom,ipc-3 = <&apcs1_mbox 8 19>;
> +
> + apps_smsm: apps@0 {
> + reg = <0>;
> +
> + #qcom,smem-state-cells = <1>;
> + };
> +
> + hexagon_smsm: hexagon@1 {
> + reg = <1>;
> + interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + wcnss_smsm: wcnss@6 {
> + reg = <6>;
> + interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + soc: soc@0 {
> +
> +
Stray newline.
compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 0 0 0xffffffff>;
> +
> + rng@...00 {
> + compatible = "qcom,prng";
> + reg = <0x00022000 0x200>;
> + clocks = <&gcc GCC_PRNG_AHB_CLK>;
> + clock-names = "core";
> + };
> +
> + qfprom: qfprom@...00 {
> + compatible = "qcom,msm8916-qfprom", "qcom,qfprom";
> + reg = <0x0005c000 0x1000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
Please add a newline between the last property and the first subnode.
> + tsens_caldata: caldata@a0 {
> + reg = <0xa0 0x5c>;
> + };
And a newline between each subnode.
> + cpr_efuse_init_voltage1: ivoltage1@dc {
> + reg = <0xdc 0x4>;
> + bits = <4 6>;
> + };
> + cpr_efuse_init_voltage2: ivoltage2@da {
> + reg = <0xda 0x4>;
> + bits = <2 6>;
> + };
> + cpr_efuse_init_voltage3: ivoltage3@d8 {
> + reg = <0xd8 0x4>;
> + bits = <0 6>;
> + };
> + cpr_efuse_quot1: quot1@dc {
> + reg = <0xdd 0x8>;
> + bits = <2 12>;
> + };
> + cpr_efuse_quot2: quot2@da {
> + reg = <0xdb 0x8>;
> + bits = <0x0 12>;
> + };
> + cpr_efuse_quot3: quot3@d8 {
> + reg = <0xd8 0x8>;
> + bits = <6 12>;
> + };
> + cpr_efuse_ring1: ring1@de {
> + reg = <0xde 0x4>;
> + bits = <6 3>;
> + };
> + cpr_efuse_ring2: ring2@de {
> + reg = <0xde 0x4>;
> + bits = <6 3>;
> + };
> + cpr_efuse_ring3: ring3@de {
> + reg = <0xde 0x4>;
> + bits = <6 3>;
> + };
> + cpr_efuse_revision: revision@4 {
> + reg = <0x5 0x1>;
> + bits = <5 1>;
> + };
> + cpr_efuse_revision_high: revision-high@4 {
> + reg = <0x7 0x1>;
> + bits = <0 1>;
> + };
> + cpr_efuse_pvs_version: pvs@4 {
> + reg = <0x3 0x1>;
> + bits = <5 1>;
> + };
> + cpr_efuse_pvs_version_high: pvs-high@4 {
> + reg = <0x6 0x1>;
> + bits = <2 2>;
> + };
> + cpr_efuse_speedbin: speedbin@c {
> + reg = <0xc 0x1>;
> + bits = <2 3>;
> + };
> +
And remove this trailing newline.
> + };
> +
> + rpm_msg_ram: sram@...00 {
> + compatible = "qcom,rpm-msg-ram";
> + reg = <0x00060000 0x8000>;
> + };
> +
> + bimc: interconnect@...000 {
> + compatible = "qcom,msm8939-bimc";
> + reg = <0x00400000 0x62000>;
> + clock-names = "bus", "bus_a";
> + clocks = <&rpmcc RPM_SMD_BIMC_CLK>,
> + <&rpmcc RPM_SMD_BIMC_A_CLK>;
> + #interconnect-cells = <1>;
> + status = "okay";
Drop, it's "okay" by default.
> + };
> +
> + tsens: thermal-sensor@...000 {
> + compatible = "qcom,msm8939-tsens", "qcom,tsens-v0_1";
> + reg = <0x004a9000 0x1000>, /* TM */
> + <0x004a8000 0x1000>; /* SROT */
> + nvmem-cells = <&tsens_caldata>;
> + nvmem-cell-names = "calib";
> + #qcom,sensors = <10>;
> + interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "uplow";
> + #thermal-sensor-cells = <1>;
> + };
> +
> + restart@...000 {
> + compatible = "qcom,pshold";
> + reg = <0x004ab000 0x4>;
> + };
> +
> + pcnoc: interconnect@...000 {
> + compatible = "qcom,msm8939-pcnoc";
> + reg = <0x00500000 0x11000>;
> + clock-names = "bus", "bus_a";
> + clocks = <&rpmcc RPM_SMD_PCNOC_CLK>,
> + <&rpmcc RPM_SMD_PCNOC_A_CLK>;
> + #interconnect-cells = <1>;
> + status = "okay";
Ditto
> + };
> +
> + snoc: interconnect@...000 {
> + compatible = "qcom,msm8939-snoc";
> + reg = <0x00580000 0x14080>;
> + clock-names = "bus", "bus_a";
> + clocks = <&rpmcc RPM_SMD_SNOC_CLK>,
> + <&rpmcc RPM_SMD_SNOC_A_CLK>;
> + #interconnect-cells = <1>;
> + status = "okay";
Ditto
> +
> + snoc_mm: interconnect-snoc {
> + compatible = "qcom,msm8939-snoc-mm";
> + clock-names = "bus", "bus_a";
> + clocks = <&rpmcc RPM_SMD_SYSMMNOC_CLK>,
> + <&rpmcc RPM_SMD_SYSMMNOC_A_CLK>;
> + #interconnect-cells = <1>;
> + status = "okay";
Ditto
> + };
> +
> + };
> +
> + msmgpio: pinctrl@...0000 {
tlmm: would be mode contemporary.
> + compatible = "qcom,msm8916-pinctrl";
> + reg = <0x01000000 0x300000>;
> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> + gpio-controller;
> + gpio-ranges = <&msmgpio 0 0 122>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + blsp1_uart1_default: blsp1-uart1-default-state {
> + pins = "gpio0", "gpio1", "gpio2", "gpio3";
> + function = "blsp_uart1";
> +
> +
Unnecessary newlines between properties.
drive-strength = <16>;
> + bias-disable;
> + };
> +
> + blsp1_uart1_sleep: blsp1-uart1-sleep-state {
> + pins = "gpio0", "gpio1", "gpio2", "gpio3";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + blsp1_uart2_default: blsp1-uart2-default-state {
> + pins = "gpio4", "gpio5";
> + function = "blsp_uart2";
> +
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + blsp1_uart2_sleep: blsp1-uart2-sleep-state {
> + pins = "gpio4", "gpio5";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + camera_front_default: camera-front-default-state {
> + pwdn-pins {
> + pins = "gpio33";
> + function = "gpio";
> +
> + drive-strength = <16>;
> + bias-disable;
> + };
Please add a newline between each subnode.
> + rst-pins {
> + pins = "gpio28";
> + function = "gpio";
> +
> + drive-strength = <16>;
> + bias-disable;
> + };
> + mclk1-pins {
> + pins = "gpio27";
> + function = "cam_mclk1";
> +
> + drive-strength = <16>;
> + bias-disable;
> + };
> + };
> +
> + camera_rear_default: camera-rear-default-state {
> + pwdn-pins {
> + pins = "gpio34";
> + function = "gpio";
> +
> + drive-strength = <16>;
> + bias-disable;
> + };
Ditto
> + rst-pins {
> + pins = "gpio35";
> + function = "gpio";
> +
> + drive-strength = <16>;
> + bias-disable;
> + };
> + mclk0-pins {
> + pins = "gpio26";
> + function = "cam_mclk0";
> +
> + drive-strength = <16>;
> + bias-disable;
> + };
> + };
> +
> + cci0_default: cci0-default-state {
> + pins = "gpio29", "gpio30";
> + function = "cci_i2c";
> +
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + cdc-pdm-lines-state {
> + cdc_pdm_lines_act: pdm-lines-on-pins {
> + pins = "gpio63", "gpio64", "gpio65", "gpio66",
> + "gpio67", "gpio68";
> + function = "cdc_pdm0";
> +
> + drive-strength = <8>;
> + bias-disable;
> + };
Ditto
> + cdc_pdm_lines_sus: pdm-lines-off-pins {
> + pins = "gpio63", "gpio64", "gpio65", "gpio66",
> + "gpio67", "gpio68";
> + function = "cdc_pdm0";
> +
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> + };
> +
> + cdc_dmic_lines_act: cdc-dmic-lines-on-state {
> + clk-pins {
> + pins = "gpio0";
> + function = "dmic0_clk";
> +
> + drive-strength = <8>;
> + };
Ditto
> + data-pins {
> + pins = "gpio1";
> + function = "dmic0_data";
> +
> + drive-strength = <8>;
> + };
> + };
> + cdc_dmic_lines_sus: cdc-dmic-lines-off-state {
> + clk-pins {
> + pins = "gpio0";
> + function = "dmic0_clk";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
Ditto
> + data-pins {
> + pins = "gpio1";
> + function = "dmic0_data";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> + };
> +
> + ext-mclk-tlmm-lines-state {
> + ext_mclk_tlmm_lines_act: mclk-lines-on-pins {
> + pins = "gpio116";
> + function = "pri_mi2s";
> +
> + drive-strength = <8>;
> + bias-disable;
> + };
Ditto, you get the point, not pointing out each next occurence
> + ext_mclk_tlmm_lines_sus: mclk-lines-off-pins {
> + pins = "gpio116";
> + function = "pri_mi2s";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> + };
> +
> + ext-pri-tlmm-lines-state {
> + ext_pri_tlmm_lines_act: ext-pa-on-pins {
> + pins = "gpio113", "gpio114", "gpio115", "gpio116";
> + function = "pri_mi2s";
> +
> + drive-strength = <8>;
> + bias-disable;
> + };
Ditto
> + ext_pri_tlmm_lines_sus: ext-pa-off-pins {
> + pins = "gpio113", "gpio114", "gpio115", "gpio116";
> + function = "pri_mi2s";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> + };
> +
> + ext-pri-ws-line-state {
> + ext_pri_ws_act: ext-pa-on-pins {
> + pins = "gpio110";
> + function = "pri_mi2s_ws";
> +
> + drive-strength = <8>;
> + bias-disable;
> + }> + ext_pri_ws_sus: ext-pa-off-pins {
> + pins = "gpio110";
> + function = "pri_mi2s_ws";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> + };
> +
> + /* secondary Mi2S */
> + ext-sec-tlmm-lines-state {
> + ext_sec_tlmm_lines_act: tlmm-lines-on-pins {
> + pins = "gpio112", "gpio117", "gpio118", "gpio119";
> + function = "sec_mi2s";
> +
> + drive-strength = <8>;
> + bias-disable;
> + };> + ext_sec_tlmm_lines_sus: tlmm-lines-off-pins {
> + pins = "gpio112", "gpio117", "gpio118", "gpio119";
> + function = "sec_mi2s";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> + };
> +
> + i2c1_default: i2c1-default-state {
> + pins = "gpio2", "gpio3";
> + function = "blsp_i2c1";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + i2c1_sleep: i2c1-sleep-state {
> + pins = "gpio2", "gpio3";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + i2c2_default: i2c2-default-state {
> + pins = "gpio6", "gpio7";
> + function = "blsp_i2c2";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + i2c2_sleep: i2c2-sleep-state {
> + pins = "gpio6", "gpio7";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + i2c3_default: i2c3-default-state {
> + pins = "gpio10", "gpio11";
> + function = "blsp_i2c3";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + i2c3_sleep: i2c3-sleep-state {
> + pins = "gpio10", "gpio11";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + i2c4_default: i2c4-default-state {
> + pins = "gpio14", "gpio15";
> + function = "blsp_i2c4";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + i2c4_sleep: i2c4-sleep-state {
> + pins = "gpio14", "gpio15";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + i2c5_default: i2c5-default-state {
> + pins = "gpio18", "gpio19";
> + function = "blsp_i2c5";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + i2c5_sleep: i2c5-sleep-state {
> + pins = "gpio18", "gpio19";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + i2c6_default: i2c6-default-state {
> + pins = "gpio22", "gpio23";
> + function = "blsp_i2c6";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + i2c6_sleep: i2c6-sleep-state {
> + pins = "gpio22", "gpio23";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + pmx-sdc1-clk-state {
> + sdc1_clk_on: clk-on-pins {
> + pins = "sdc1_clk";
> +
> + bias-disable;
> + drive-strength = <16>;
> + };
> + sdc1_clk_off: clk-off-pins {
> + pins = "sdc1_clk";
> +
> + bias-disable;
> + drive-strength = <2>;
> + };
> + };
> +
> + pmx-sdc1-cmd-state {
> + sdc1_cmd_on: cmd-on-pins {
> + pins = "sdc1_cmd";
> +
> + bias-pull-up;
> + drive-strength = <10>;
> + };
> + sdc1_cmd_off: cmd-off-pins {
> + pins = "sdc1_cmd";
> +
> + bias-pull-up;
> + drive-strength = <2>;
> + };
> + };
> +
> + pmx-sdc1-data-state {
> + sdc1_data_on: data-on-pins {
> + pins = "sdc1_data";
> +
> + bias-pull-up;
> + drive-strength = <10>;
> + };
> + sdc1_data_off: data-off-pins {
> + pins = "sdc1_data";
> +
> + bias-pull-up;
> + drive-strength = <2>;
> + };
> + };
> +
> + pmx-sdc2-clk-state {
> + sdc2_clk_on: clk-on-pins {
> + pins = "sdc2_clk";
> +
> + bias-disable;
> + drive-strength = <16>;
> + };
> + sdc2_clk_off: clk-off-pins {
> + pins = "sdc2_clk";
> +
> + bias-disable;
> + drive-strength = <2>;
> + };
> + };
> +
> + pmx-sdc2-cmd-state {
> + sdc2_cmd_on: cmd-on-pins {
> + pins = "sdc2_cmd";
> +
> + bias-pull-up;
> + drive-strength = <10>;
> + };
> + sdc2_cmd_off: cmd-off-pins {
> + pins = "sdc2_cmd";
> +
> + bias-pull-up;
> + drive-strength = <2>;
> + };
> + };
> +
> + pmx-sdc2-data-state {
> + sdc2_data_on: data-on-pins {
> + pins = "sdc2_data";
> +
> + bias-pull-up;
> + drive-strength = <10>;
> + };
> + sdc2_data_off: data-off-pins {
> + pins = "sdc2_data";
> +
> + bias-pull-up;
> + drive-strength = <2>;
> + };
> + };
> +
> + pmx-sdc2-cd-pin-state {
> + sdc2_cd_on: cd-on-pins {
> + pins = "gpio38";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> + sdc2_cd_off: cd-off-pins {
> + pins = "gpio38";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> + };
> +
> + spi1_default: spi1-default-state {
> + spi-pins {
> + pins = "gpio0", "gpio1", "gpio3";
> + function = "blsp_spi1";
> +
> + drive-strength = <12>;
> + bias-disable;
> + };
> + cs-pins {
> + pins = "gpio2";
> + function = "gpio";
> +
> + drive-strength = <16>;
> + bias-disable;
> + output-high;
> + };
> + };
> +
> + spi1_sleep: spi1-sleep-state {
> + pins = "gpio0", "gpio1", "gpio2", "gpio3";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + spi2_default: spi2-default-state {
> + spi-pins {
> + pins = "gpio4", "gpio5", "gpio7";
> + function = "blsp_spi2";
> +
> + drive-strength = <12>;
> + bias-disable;
> + };
> + cs-pins {
> + pins = "gpio6";
> + function = "gpio";
> +
> + drive-strength = <16>;
> + bias-disable;
> + output-high;
> + };
> + };
> +
> + spi2_sleep: spi2-sleep-state {
> + pins = "gpio4", "gpio5", "gpio6", "gpio7";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + spi3_default: spi3-default-state {
> + spi-pins {
> + pins = "gpio8", "gpio9", "gpio11";
> + function = "blsp_spi3";
> +
> + drive-strength = <12>;
> + bias-disable;
> + };
> + cs-pins {
> + pins = "gpio10";
> + function = "gpio";
> +
> + drive-strength = <16>;
> + bias-disable;
> + output-high;
> + };
> + };
> +
> + spi3_sleep: spi3-sleep-state {
> + pins = "gpio8", "gpio9", "gpio10", "gpio11";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + spi4_default: spi4-default-state {
> + spi-pins {
> + pins = "gpio12", "gpio13", "gpio15";
> + function = "blsp_spi4";
> +
> + drive-strength = <12>;
> + bias-disable;
> + };
> + cs-pins {
> + pins = "gpio14";
> + function = "gpio";
> +
> + drive-strength = <16>;
> + bias-disable;
> + output-high;
> + };
> + };
> +
> + spi4_sleep: spi4-sleep-state {
> + pins = "gpio12", "gpio13", "gpio14", "gpio15";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + spi5_default: spi5-default-state {
> + spi-pins {
> + pins = "gpio16", "gpio17", "gpio19";
> + function = "blsp_spi5";
> +
> + drive-strength = <12>;
> + bias-disable;
> + };
> + cs-pins {
> + pins = "gpio18";
> + function = "gpio";
> +
> + drive-strength = <16>;
> + bias-disable;
> + output-high;
> + };
> + };
> +
> + spi5_sleep: spi5-sleep-state {
> + pins = "gpio16", "gpio17", "gpio18", "gpio19";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + spi6_default: spi6-default-state {
> + spi-pins {
> + pins = "gpio20", "gpio21", "gpio23";
> + function = "blsp_spi6";
> +
> + drive-strength = <12>;
> + bias-disable;
> + };
> + cs-pins {
> + pins = "gpio22";
> + function = "gpio";
> +
> + drive-strength = <16>;
> + bias-disable;
> + output-high;
> + };
> + };
> +
> + spi6_sleep: spi6-sleep-state {
> + pins = "gpio20", "gpio21", "gpio22", "gpio23";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + wcnss_pin_a: wcnss-active-state {
> + pins = "gpio40", "gpio41", "gpio42", "gpio43", "gpio44";
> + function = "wcss_wlan";
> +
> + drive-strength = <6>;
> + bias-pull-up;
> + };
> + };
> +
> + gcc: clock-controller@...0000 {
> + compatible = "qcom,gcc-msm8939";
> + reg = <0x01800000 0x80000>;
> + clocks = <&xo_board>,
Would rpmcc XO work here?
> + <&sleep_clk>,
> + <&dsi_phy0 1>,
> + <&dsi_phy0 0>,
> + <0>,
> + <0>,
> + <0>;
> + clock-names = "xo",
> + "sleep_clk",
> + "dsi0pll",
> + "dsi0pllbyte",
> + "ext_mclk",
> + "ext_pri_i2s",
> + "ext_sec_i2s";
> + #clock-cells = <1>;
> + #reset-cells = <1>;
> + #power-domain-cells = <1>;
> + };
> +
> + tcsr_mutex: hwlock@...5000 {
> + compatible = "qcom,tcsr-mutex";
> + reg = <0x01905000 0x20000>;
> + #hwlock-cells = <1>;
> + };
> +
> + tcsr: syscon@...7000 {
> + compatible = "qcom,tcsr-msm8916", "syscon";
> + reg = <0x01937000 0x30000>;
> + };
> +
> + mdss: mdss@...0000 {
display-subsystem@
> + compatible = "qcom,mdss";
> + reg = <0x01a00000 0x1000>,
> + <0x01ac8000 0x3000>;
> + reg-names = "mdss_phys", "vbif_phys";
> +
> + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> +
> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
> + <&gcc GCC_MDSS_AXI_CLK>,
> + <&gcc GCC_MDSS_VSYNC_CLK>;
> + clock-names = "iface",
> + "bus",
> + "vsync";
> +
> + power-domains = <&gcc MDSS_GDSC>;
> +
> + #address-cells = <1>;
> + #size-cells = <1>;
> + #interrupt-cells = <1>;
> + ranges;
> +
> + mdp: mdp@...1000 {
display-controller@
> + compatible = "qcom,mdp5";
> + reg = <0x01a01000 0x89000>;
> + reg-names = "mdp_phys";
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <0>;
> +
> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
> + <&gcc GCC_MDSS_AXI_CLK>,
> + <&gcc GCC_MDSS_MDP_CLK>,
> + <&gcc GCC_MDSS_VSYNC_CLK>,
> + <&gcc GCC_MDP_TBU_CLK>,
> + <&gcc GCC_MDP_RT_TBU_CLK>;
> + clock-names = "iface",
> + "bus",
> + "core",
> + "vsync",
> + "tbu",
> + "tbu_rt";
> +
> + iommus = <&apps_iommu 4>;
> +
> + interconnects = <&snoc_mm MASTER_MDP_PORT0 &bimc SLAVE_EBI_CH0>,
> + <&snoc_mm MASTER_MDP_PORT1 &bimc SLAVE_EBI_CH0>,
> + <&pcnoc MASTER_SPDM &snoc SLAVE_IMEM>;
> + interconnect-names = "mdp0-mem", "mdp1-mem", "register-mem";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + mdp5_intf1_out: endpoint {
> + remote-endpoint = <&dsi0_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + mdp5_intf2_out: endpoint {
> + remote-endpoint = <&dsi1_in>;
> + };
> + };
> + };
> + };
> +
> + dsi0: dsi@...8000 {
> + compatible = "qcom,msm8916-dsi-ctrl",
> + "qcom,mdss-dsi-ctrl";
> + reg = <0x01a98000 0x25c>;
> + reg-names = "dsi_ctrl";
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <4>;
> +
> + power-domains = <&gcc MDSS_GDSC>;
> +
> + clocks = <&gcc GCC_MDSS_MDP_CLK>,
> + <&gcc GCC_MDSS_AHB_CLK>,
> + <&gcc GCC_MDSS_AXI_CLK>,
> + <&gcc GCC_MDSS_BYTE0_CLK>,
> + <&gcc GCC_MDSS_PCLK0_CLK>,
> + <&gcc GCC_MDSS_ESC0_CLK>;
> + clock-names = "mdp_core",
> + "iface",
> + "bus",
> + "byte",
> + "pixel",
> + "core";
> + assigned-clocks = <&gcc BYTE0_CLK_SRC>,
> + <&gcc PCLK0_CLK_SRC>;
> + assigned-clock-parents = <&dsi_phy0 0>,
> + <&dsi_phy0 1>;
> +
> + phys = <&dsi_phy0>;
> + status = "disabled";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + dsi0_in: endpoint {
> + remote-endpoint = <&mdp5_intf1_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + dsi0_out: endpoint {
> + };
> + };
> + };
> + };
> +
> + dsi_phy0: phy@...8300 {
> + compatible = "qcom,dsi-phy-28nm-lp";
> + reg = <0x01a98300 0xd4>,
> + <0x01a98500 0x280>,
> + <0x01a98780 0x30>;
> + reg-names = "dsi_pll",
> + "dsi_phy",
> + "dsi_phy_regulator";
> +
> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
> + <&xo_board>;
> + clock-names = "iface", "ref";
> +
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> + status = "disabled";
> + };
> +
> + dsi1: dsi@...0000 {
> + compatible = "qcom,msm8916-dsi-ctrl",
> + "qcom,mdss-dsi-ctrl";
> + reg = <0x01aa0000 0x25c>;
> + reg-names = "dsi_ctrl";
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <5>;
> +
> + power-domains = <&gcc MDSS_GDSC>;
> +
> + clocks = <&gcc GCC_MDSS_MDP_CLK>,
> + <&gcc GCC_MDSS_AHB_CLK>,
> + <&gcc GCC_MDSS_AXI_CLK>,
> + <&gcc GCC_MDSS_BYTE1_CLK>,
> + <&gcc GCC_MDSS_PCLK1_CLK>,
> + <&gcc GCC_MDSS_ESC1_CLK>;
> + clock-names = "mdp_core",
> + "iface",
> + "bus",
> + "byte",
> + "pixel",
> + "core";
> + assigned-clocks = <&gcc BYTE1_CLK_SRC>,
> + <&gcc PCLK1_CLK_SRC>;
> + assigned-clock-parents = <&dsi_phy1 0>,
> + <&dsi_phy1 1>;
> + phys = <&dsi_phy1>;
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + dsi1_in: endpoint {
> + remote-endpoint = <&mdp5_intf2_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + dsi1_out: endpoint {
> + };
> + };
> + };
> + };
> +
> + dsi_phy1: phy@...0300 {
> + compatible = "qcom,dsi-phy-28nm-lp";
> + reg = <0x01aa0300 0xd4>,
> + <0x01aa0500 0x280>,
> + <0x01aa0780 0x30>;
> + reg-names = "dsi_pll",
> + "dsi_phy",
> + "dsi_phy_regulator";
> +
> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
> + <&xo_board>;
rpmcc XO here and in dsi0phy?
> + clock-names = "iface", "ref";
> +
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> + status = "disabled";
> + };
> + };
> +
> + gpu@...0000 {
> + compatible = "qcom,adreno-405.0", "qcom,adreno";
> + reg = <0x01c00000 0x10000>;
> + reg-names = "kgsl_3d0_reg_memory";
> + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "kgsl_3d0_irq";
> + clock-names = "core",
> + "iface",
> + "mem",
> + "mem_iface",
> + "alt_mem_iface",
> + "gfx3d",
> + "rbbmtimer";
> + clocks = <&gcc GCC_OXILI_GFX3D_CLK>,
> + <&gcc GCC_OXILI_AHB_CLK>,
> + <&gcc GCC_OXILI_GMEM_CLK>,
> + <&gcc GCC_BIMC_GFX_CLK>,
> + <&gcc GCC_BIMC_GPU_CLK>,
> + <&gcc GFX3D_CLK_SRC>,
> + <&gcc GCC_OXILI_TIMER_CLK>;
> + power-domains = <&gcc OXILI_GDSC>;
> + operating-points-v2 = <&opp_table>;
> + iommus = <&gpu_iommu 1>, <&gpu_iommu 2>;
No interconnect?
> +
> + opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-550000000 {
> + opp-hz = /bits/ 64 <550000000>;
> + };
> +
> + opp-465000000 {
> + opp-hz = /bits/ 64 <465000000>;
> + };
> +
> + opp-400000000 {
> + opp-hz = /bits/ 64 <400000000>;
> + };
> +
> + opp-220000000 {
> + opp-hz = /bits/ 64 <220000000>;
> + };
> +
> + opp-19200000 {
> + opp-hz = /bits/ 64 <19200000>;
> + };
> + };
> + };
> +
> + apps_iommu: iommu@...0000 {
> + compatible = "qcom,msm8916-iommu", "qcom,msm-iommu-v1";
> + reg = <0x01ef0000 0x3000>;
> + ranges = <0 0x1e20000 0x40000>;
> + clocks = <&gcc GCC_SMMU_CFG_CLK>,
> + <&gcc GCC_APSS_TCU_CLK>;
> + clock-names = "iface", "bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + #iommu-cells = <1>;
> + qcom,iommu-secure-id = <17>;
> +
> + /* mdp_0: */
> + iommu-ctx@...0 {
> + compatible = "qcom,msm-iommu-v1-ns";
> + reg = <0x4000 0x1000>;
> + interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + /* venus_ns: */
> + iommu-ctx@...0 {
> + compatible = "qcom,msm-iommu-v1-sec";
> + reg = <0x5000 0x1000>;
> + interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> + };
> + };
> +
> + gpu_iommu: iommu@...8000 {
> + compatible = "qcom,msm8916-iommu", "qcom,msm-iommu-v1";
> + ranges = <0 0x1f08000 0x10000>;
> + clocks = <&gcc GCC_SMMU_CFG_CLK>,
> + <&gcc GCC_GFX_TCU_CLK>,
> + <&gcc GCC_GFX_TBU_CLK>;
> + clock-names = "iface", "bus", "tbu";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + #iommu-cells = <1>;
> + qcom,iommu-secure-id = <18>;
> +
> + /* gfx3d_user: */
> + iommu-ctx@...0 {
> + compatible = "qcom,msm-iommu-v1-ns";
> + reg = <0x1000 0x1000>;
> + interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + /* gfx3d_priv: */
> + iommu-ctx@...0 {
> + compatible = "qcom,msm-iommu-v1-ns";
> + reg = <0x2000 0x1000>;
> + interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>;
> + };
> + };
> +
> + spmi_bus: spmi@...f000 {
> + compatible = "qcom,spmi-pmic-arb";
> + reg = <0x0200f000 0x001000>,
> + <0x02400000 0x400000>,
> + <0x02c00000 0x400000>,
> + <0x03800000 0x200000>,
> + <0x0200a000 0x002100>;
> + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
> + interrupt-names = "periph_irq";
> + interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
> + qcom,ee = <0>;
> + qcom,channel = <0>;
> + #address-cells = <2>;
> + #size-cells = <0>;
> + interrupt-controller;
> + #interrupt-cells = <4>;
> + };
> +
> + mpss: remoteproc@...0000 {
> + compatible = "qcom,msm8916-mss-pil";
> + reg = <0x04080000 0x100>,
> + <0x04020000 0x040>;
> +
> + reg-names = "qdsp6", "rmb";
> +
> + interrupts-extended = <&intc GIC_SPI 24 IRQ_TYPE_EDGE_RISING>,
> + <&hexagon_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> + <&hexagon_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
> + <&hexagon_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
> + <&hexagon_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "wdog", "fatal", "ready",
> + "handover", "stop-ack";
> +
> + clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
> + <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>,
> + <&gcc GCC_BOOT_ROM_AHB_CLK>,
> + <&xo_board>;
> + clock-names = "iface", "bus", "mem", "xo";
> +
> + power-domains = <&rpmpd MSM8939_VDDMDCX>,
> + <&rpmpd MSM8939_VDDMX>;
> + power-domain-names = "cx", "mx";
> +
> + qcom,smem-states = <&hexagon_smp2p_out 0>;
> + qcom,smem-state-names = "stop";
> +
> + resets = <&scm 0>;
> + reset-names = "mss_restart";
> +
> + qcom,halt-regs = <&tcsr 0x18000 0x19000 0x1a000>;
> +
> + status = "disabled";
> +
> + mba {
> + memory-region = <&mba_mem>;
> + };
> +
> + mpss {
> + memory-region = <&mpss_mem>;
> + };
> +
> + smd-edge {
> + interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
> +
> + qcom,smd-edge = <0>;
> + mboxes = <&apcs1_mbox 12>;
> + qcom,remote-pid = <1>;
> +
> + label = "hexagon";
> + };
> + };
> +
> + sound: sound@...2000 {
> + compatible = "qcom,apq8016-sbc-sndcard";
> + reg = <0x07702000 0x4>,
> + <0x07702004 0x4>;
> + reg-names = "mic-iomux", "spkr-iomux";
> + status = "disabled";
> + };
> +
> + lpass: audio-controller@...8000 {
> + compatible = "qcom,apq8016-lpass-cpu";
> + reg = <0x07708000 0x10000>;
> + reg-names = "lpass-lpaif";
> + interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "lpass-irq-lpaif";
> + clocks = <&gcc GCC_ULTAUDIO_AHBFABRIC_IXFABRIC_CLK>,
> + <&gcc GCC_ULTAUDIO_LPAIF_PRI_I2S_CLK>,
> + <&gcc GCC_ULTAUDIO_LPAIF_PRI_I2S_CLK>,
> + <&gcc GCC_ULTAUDIO_LPAIF_SEC_I2S_CLK>,
> + <&gcc GCC_ULTAUDIO_LPAIF_AUX_I2S_CLK>,
> + <&gcc GCC_ULTAUDIO_PCNOC_MPORT_CLK>,
> + <&gcc GCC_ULTAUDIO_PCNOC_SWAY_CLK>;
> + clock-names = "ahbix-clk",
> + "mi2s-bit-clk0",
> + "mi2s-bit-clk1",
> + "mi2s-bit-clk2",
> + "mi2s-bit-clk3",
> + "pcnoc-mport-clk",
> + "pcnoc-sway-clk";
> + #sound-dai-cells = <1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + lpass_codec: audio-codec@...c000 {
> + compatible = "qcom,msm8916-wcd-digital-codec";
> + reg = <0x0771c000 0x400>;
> + clocks = <&gcc GCC_ULTAUDIO_AHBFABRIC_IXFABRIC_CLK>,
> + <&gcc GCC_CODEC_DIGCODEC_CLK>;
> + clock-names = "ahbix-clk", "mclk";
> + #sound-dai-cells = <1>;
> + };
> +
> + blsp_dma: dma-controller@...4000 {
> + compatible = "qcom,bam-v1.7.0";
> + reg = <0x07884000 0x23000>;
> + interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "bam_clk";
> + #dma-cells = <1>;
> + qcom,ee = <0>;
> + status = "disabled";
> + };
> +
> + blsp1_uart1: serial@...f000 {
> + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
> + reg = <0x078af000 0x200>;
> + interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp_dma 0>, <&blsp_dma 1>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&blsp1_uart1_default>;
> + pinctrl-1 = <&blsp1_uart1_sleep>;
> + status = "disabled";
> + };
> +
> + blsp1_uart2: serial@...0000 {
> + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
> + reg = <0x078b0000 0x200>;
> + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp_dma 2>, <&blsp_dma 3>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&blsp1_uart2_default>;
> + pinctrl-1 = <&blsp1_uart2_sleep>;
> + status = "disabled";
> + };
> +
> + blsp_i2c1: i2c@...5000 {
> + compatible = "qcom,i2c-qup-v2.2.1";
> + reg = <0x078b5000 0x500>;
> + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
> + <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp_dma 4>, <&blsp_dma 5>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&i2c1_default>;
> + pinctrl-1 = <&i2c1_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + blsp_i2c2: i2c@...6000 {
> + compatible = "qcom,i2c-qup-v2.2.1";
> + reg = <0x078b6000 0x500>;
> + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
> + <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp_dma 6>, <&blsp_dma 7>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&i2c2_default>;
> + pinctrl-1 = <&i2c2_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + blsp_i2c3: i2c@...7000 {
> + compatible = "qcom,i2c-qup-v2.2.1";
> + reg = <0x078b7000 0x500>;
> + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
> + <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp_dma 8>, <&blsp_dma 9>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&i2c3_default>;
> + pinctrl-1 = <&i2c3_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + blsp_i2c4: i2c@...8000 {
> + compatible = "qcom,i2c-qup-v2.2.1";
> + reg = <0x078b8000 0x500>;
> + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
> + <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp_dma 10>, <&blsp_dma 11>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&i2c4_default>;
> + pinctrl-1 = <&i2c4_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + blsp_i2c5: i2c@...9000 {
> + compatible = "qcom,i2c-qup-v2.2.1";
> + reg = <0x078b9000 0x500>;
> + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>,
> + <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp_dma 12>, <&blsp_dma 13>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&i2c5_default>;
> + pinctrl-1 = <&i2c5_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + blsp_i2c6: i2c@...a000 {
> + compatible = "qcom,i2c-qup-v2.2.1";
> + reg = <0x078ba000 0x500>;
> + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>,
> + <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp_dma 14>, <&blsp_dma 15>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&i2c6_default>;
> + pinctrl-1 = <&i2c6_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + blsp_spi1: spi@...5000 {
> + compatible = "qcom,spi-qup-v2.2.1";
> + reg = <0x078b5000 0x500>;
> + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
> + <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp_dma 4>, <&blsp_dma 5>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&spi1_default>;
> + pinctrl-1 = <&spi1_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + blsp_spi2: spi@...6000 {
> + compatible = "qcom,spi-qup-v2.2.1";
> + reg = <0x078b6000 0x500>;
> + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
> + <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp_dma 6>, <&blsp_dma 7>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&spi2_default>;
> + pinctrl-1 = <&spi2_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + blsp_spi3: spi@...7000 {
> + compatible = "qcom,spi-qup-v2.2.1";
> + reg = <0x078b7000 0x500>;
> + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
> + <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp_dma 8>, <&blsp_dma 9>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&spi3_default>;
> + pinctrl-1 = <&spi3_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + blsp_spi4: spi@...8000 {
> + compatible = "qcom,spi-qup-v2.2.1";
> + reg = <0x078b8000 0x500>;
> + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>,
> + <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp_dma 10>, <&blsp_dma 11>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&spi4_default>;
> + pinctrl-1 = <&spi4_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + blsp_spi5: spi@...9000 {
> + compatible = "qcom,spi-qup-v2.2.1";
> + reg = <0x078b9000 0x500>;
> + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_QUP5_SPI_APPS_CLK>,
> + <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp_dma 12>, <&blsp_dma 13>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&spi5_default>;
> + pinctrl-1 = <&spi5_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + blsp_spi6: spi@...a000 {
> + compatible = "qcom,spi-qup-v2.2.1";
> + reg = <0x078ba000 0x500>;
> + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_QUP6_SPI_APPS_CLK>,
> + <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "core", "iface";
> + dmas = <&blsp_dma 14>, <&blsp_dma 15>;
> + dma-names = "tx", "rx";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&spi6_default>;
> + pinctrl-1 = <&spi6_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + sdhc_1: mmc@...4000 {
> + compatible = "qcom,msm8916-sdhci", "qcom,sdhci-msm-v4";
> + reg = <0x07824900 0x11c>,
> + <0x07824000 0x800>;
> + reg-names = "hc", "core";
> +
> + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, <0 138 IRQ_TYPE_LEVEL_HIGH>;
Replace 0 with GIC_SPI and wrap the line, please.
> + interrupt-names = "hc_irq", "pwr_irq";
> + clocks = <&gcc GCC_SDCC1_AHB_CLK>,
> + <&gcc GCC_SDCC1_APPS_CLK>,
> + <&xo_board>;
rpm xo if it works, please!
> + clock-names = "iface", "core", "xo";
> + resets = <&gcc GCC_SDCC1_BCR>;
> + mmc-ddr-1_8v;
> + bus-width = <8>;
> + non-removable;
> + status = "disabled";
> + };
> +
> + sdhc_2: mmc@...4000 {
> + compatible = "qcom,msm8916-sdhci", "qcom,sdhci-msm-v4";
> + reg = <0x07864900 0x11c>,
> + <0x07864000 0x800>;
> + reg-names = "hc", "core";
> +
> + interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, <0 221 IRQ_TYPE_LEVEL_HIGH>;
Ditto_A
> + interrupt-names = "hc_irq", "pwr_irq";
> + clocks = <&gcc GCC_SDCC2_AHB_CLK>,
> + <&gcc GCC_SDCC2_APPS_CLK>,
> + <&xo_board>;
Ditto_B
> + clock-names = "iface", "core", "xo";
> + resets = <&gcc GCC_SDCC2_BCR>;
> + bus-width = <4>;
> + status = "disabled";
> + };
> +
> + usb: usb@...9000 {
> + compatible = "qcom,ci-hdrc";
> + reg = <0x078d9000 0x200>,
> + <0x078d9200 0x200>;
> + interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_USB_HS_AHB_CLK>,
> + <&gcc GCC_USB_HS_SYSTEM_CLK>;
> + clock-names = "iface", "core";
> + assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
> + assigned-clock-rates = <80000000>;
> + resets = <&gcc GCC_USB_HS_BCR>;
> + reset-names = "core";
> + #reset-cells = <1>;
> + phy_type = "ulpi";
> + dr_mode = "otg";
> + ahb-burst-config = <0>;
> + phy-names = "usb-phy";
> + phys = <&usb_hs_phy>;
> + status = "disabled";
> +
> + ulpi {
> + usb_hs_phy: phy {
> + compatible = "qcom,usb-hs-phy-msm8916",
> + "qcom,usb-hs-phy";
> + clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
> + clock-names = "ref", "sleep";
> + resets = <&gcc GCC_USB2A_PHY_BCR>, <&usb 0>;
> + reset-names = "phy", "por";
> + #phy-cells = <0>;
> + qcom,init-seq = /bits/ 8 <0x0 0x44
> + 0x1 0x6b 0x2 0x24 0x3 0x13>;
> + };
> + };
> + };
> +
> + intc: interrupt-controller@...0000 {
> + compatible = "qcom,msm-qgic2";
> + reg = <0x0b000000 0x1000>, <0x0b002000 0x2000>,
> + <0x0b001000 0x1000>, <0x0b004000 0x2000>;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupts = <GIC_PPI 0 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
> + };
> +
> + apcs1_mbox: mailbox@...1000 {
> + compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
> + reg = <0x0b011000 0x1000>;
> + clocks = <&a53pll_c1>, <&gcc GPLL0_VOTE>, <&xo_board>;
> + clock-names = "pll", "aux", "ref";
> + #clock-cells = <0>;
> + assigned-clocks = <&apcs2>;
> + assigned-clock-rates = <297600000>;
> + #mbox-cells = <1>;
> + };
> +
> + a53pll_c1: clock@...6000 {
> + compatible = "qcom,msm8939-a53pll";
> + reg = <0x0b016000 0x40>;
> + #clock-cells = <0>;
> + };
> +
> + acc0: clock-controller@...8000 {
> + compatible = "qcom,kpss-acc-v2";
> + reg = <0x0b088000 0x1000>;
> + };
> +
> + saw0: power-manager@...9000 {
> + compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
> + reg = <0x0b089000 0x1000>;
> + };
> +
> + acc1: clock-controller@...8000 {
> + compatible = "qcom,kpss-acc-v2";
> + reg = <0x0b098000 0x1000>;
> + };
> +
> + saw1: power-manager@...9000 {
> + compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
> + reg = <0x0b099000 0x1000>;
> + };
> +
> + acc2: clock-controller@...8000 {
> + compatible = "qcom,kpss-acc-v2";
> + reg = <0x0b0a8000 0x1000>;
> + };
> +
> + saw2: power-manager@...9000 {
> + compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
> + reg = <0x0b0a9000 0x1000>;
> + };
> +
> + acc3: clock-controller@...8000 {
> + compatible = "qcom,kpss-acc-v2";
> + reg = <0x0b0b8000 0x1000>;
> + };
> +
> + saw3: power-manager@...9000 {
> + compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
> + reg = <0x0b0b9000 0x1000>;
> + };
> +
> + apcs0_mbox: mailbox@...1000 {
> + compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
> + reg = <0x0b111000 0x1000>;
> + clocks = <&a53pll_c0>, <&gcc GPLL0_VOTE>, <&xo_board>;
> + clock-names = "pll", "aux", "ref";
> + #clock-cells = <0>;
> + #mbox-cells = <1>;
> + };
> +
> + a53pll_c0: clock@...6000 {
> + compatible = "qcom,msm8939-a53pll";
> + reg = <0x0b116000 0x40>;
> + #clock-cells = <0>;
> + };
> +
> + acc4: clock-controller@...8000 {
> + compatible = "qcom,kpss-acc-v2";
> + reg = <0x0b188000 0x1000>;
> + };
> +
> + saw4: power-manager@...9000 {
> + compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
> + reg = <0x0b189000 0x1000>;
> + };
> +
> + acc5: clock-controller@...8000 {
> + compatible = "qcom,kpss-acc-v2";
> + reg = <0x0b198000 0x1000>;
> + };
> +
> + saw5: power-manager@...9000 {
> + compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
> + reg = <0x0b199000 0x1000>;
> + };
> +
> + acc6: clock-controller@...8000 {
> + compatible = "qcom,kpss-acc-v2";
> + reg = <0x0b1a8000 0x1000>;
> + };
> +
> + saw6: power-manager@...9000 {
> + compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
> + reg = <0x0b1a9000 0x1000>;
> + };
> +
> + acc7: clock-controller@...8000 {
> + compatible = "qcom,kpss-acc-v2";
> + reg = <0x0b1b8000 0x1000>;
> + };
> +
> + saw7: power-manager@...9000 {
> + compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
> + reg = <0x0b1b9000 0x1000>;
> + };
> +
> + a53pll_cci: clock@...0000 {
> + compatible = "qcom,msm8939-a53pll";
> + reg = <0x0b1d0000 0x40>;
> + #clock-cells = <0>;
> + };
> +
> + apcs2: mailbox@...1000 {
> + compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
> + reg = <0x0b1d1000 0x1000>;
> + clocks = <&a53pll_cci>, <&gcc GPLL0_VOTE>, <&xo_board>;
> + clock-names = "pll", "aux", "ref";
> + #clock-cells = <0>;
> + #mbox-cells = <1>;
> + };
> +
> + timer@...0000 {
> + compatible = "arm,armv7-timer-mem";
> + reg = <0x0b020000 0x1000>;
> + clock-frequency = <19200000>;
This property should be omitted unless it's absolutely necessary
(a.k.a. your board doesn't boot without it), but on Qcom 11/10
times it's not necessary, as some earlier part of the boot chain
takes care of setting CNTFRQ_ELn.
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + frame@...1000 {
> + frame-number = <0>;
> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x0b021000 0x1000>,
> + <0x0b022000 0x1000>;
Please shuffle these properties so that it's
reg
interrupts
frame-number
[status]
for all of these nodes
> + };
> +
> + frame@...3000 {
> + frame-number = <1>;
> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x0b023000 0x1000>;
> + status = "disabled";
> + };
> +
> + frame@...4000 {
> + frame-number = <2>;
> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x0b024000 0x1000>;
> + status = "disabled";
> + };
> +
> + frame@...5000 {
> + frame-number = <3>;
> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x0b025000 0x1000>;
> + status = "disabled";
> + };
> +
> + frame@...6000 {
> + frame-number = <4>;
> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x0b026000 0x1000>;
> + status = "disabled";
> + };
> +
> + frame@...7000 {
> + frame-number = <5>;
> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x0b027000 0x1000>;
> + status = "disabled";
> + };
> +
> + frame@...8000 {
> + frame-number = <6>;
> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x0b028000 0x1000>;
> + status = "disabled";
> + };
> + };
> +
> + pronto: remoteproc@...4000 {
> + compatible = "qcom,pronto-v2-pil", "qcom,pronto";
> + reg = <0x0a204000 0x2000>,
> + <0x0a202000 0x1000>,
> + <0x0a21b000 0x3000>;
> + reg-names = "ccu", "dxe", "pmu";
> +
> + interrupts-extended = <&intc 0 149 IRQ_TYPE_EDGE_RISING>,
> + <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> + <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
> + <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
> + <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
> +
> + memory-region = <&wcnss_mem>;
> +
> + power-domains = <&rpmpd MSM8939_VDDCX>,
> + <&rpmpd MSM8939_VDDMX_AO>;
> + power-domain-names = "cx", "mx";
> +
> + qcom,smem-states = <&wcnss_smp2p_out 0>;
> + qcom,smem-state-names = "stop";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&wcnss_pin_a>;
> +
> + status = "disabled";
> +
> + iris {
> + compatible = "qcom,wcn3620";
> +
Let's drop this newline.
> + clocks = <&rpmcc RPM_SMD_RF_CLK2>;
> + clock-names = "xo";
> + };
> +
> + smd-edge {
> + interrupts = <GIC_SPI 142 1>;
> +
And maybe this one too.
> + qcom,ipc = <&apcs1_mbox 8 17>;
> + qcom,smd-edge = <6>;
> + qcom,remote-pid = <4>;
> +
> + label = "pronto";
> +
> + wcnss {
> + compatible = "qcom,wcnss";
> + qcom,smd-channels = "WCNSS_CTRL";
> +
> + qcom,mmio = <&pronto>;
> +
> + bluetooth {
> + compatible = "qcom,wcnss-bt";
> + };
> +
> + wifi {
> + compatible = "qcom,wcnss-wlan";
> +
> + interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "tx", "rx";
> +
> + qcom,smem-states = <&apps_smsm 10>,
> + <&apps_smsm 9>;
> + qcom,smem-state-names = "tx-enable",
> + "tx-rings-empty";
> + };
> + };
> + };
> + };
> + };
> +
> + smd {
> + compatible = "qcom,smd";
> +
> + rpm {
> + interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
> + qcom,ipc = <&apcs1_mbox 8 0>;
> + qcom,smd-edge = <15>;
> +
> + rpm_requests: rpm-requests {
> + compatible = "qcom,rpm-msm8936";
> + qcom,smd-channels = "rpm_requests";
> +
> + rpmcc: clock-controller {
> + compatible = "qcom,rpmcc-msm8936", "qcom,rpmcc";
> + #clock-cells = <1>;
> + };
> +
> + rpmpd: power-controller {
> + compatible = "qcom,msm8939-rpmpd";
> + #power-domain-cells = <1>;
> + operating-points-v2 = <&rpmpd_opp_table>;
> +
> + rpmpd_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + rpmpd_opp_ret: opp1 {
> + opp-level = <1>;
> + };
> +
> + rpmpd_opp_svs_krait: opp2 {
> + opp-level = <2>;
> + };
> +
> + rpmpd_opp_svs_soc: opp3 {
> + opp-level = <3>;
> + };
> +
> + rpmpd_opp_nom: opp4 {
> + opp-level = <4>;
> + };
> +
> + rpmpd_opp_turbo: opp5 {
> + opp-level = <5>;
> + };
> +
> + rpmpd_opp_super_turbo: opp6 {
> + opp-level = <6>;
> + };
> + };
> + };
> + };
> + };
> + };
> +
> + thermal_zones: thermal-zones {
> + cpu0-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens 5>;
> +
> + trips {
> + cpu0_alert: trip0 {
> + temperature = <75000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
Add a newline after each subnode, please.
> + cpu0_crit: trip1 {
> + temperature = <115000>;
> + hysteresis = <0>;
> + type = "critical";
> + };
> + };
> +
> + cooling-maps {
> + map0 {
> + trip = <&cpu0_alert>;
> + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> +
> + cpu1-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens 6>;
> +
> + trips {
> + cpu1_alert: trip0 {
> + temperature = <75000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> + cpu1_crit: trip1 {
> + temperature = <110000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> +
> + cooling-maps {
> + map0 {
> + trip = <&cpu1_alert>;
> + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> +
> + cpu2-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens 7>;
> +
> + trips {
> + cpu2_alert: trip0 {
> + temperature = <75000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> + cpu2_crit: trip1 {
> + temperature = <110000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> +
> + cooling-maps {
> + map0 {
> + trip = <&cpu2_alert>;
> + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> +
> + cpu3-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens 8>;
> +
> + trips {
> + cpu3_alert: trip0 {
> + temperature = <75000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> + cpu3_crit: trip1 {
> + temperature = <110000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> +
> + cooling-maps {
> + map0 {
> + trip = <&cpu3_alert>;
> + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> +
> + cpu4567-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens 9>;
> +
> + trips {
> + cpu4567_alert: trip0 {
> + temperature = <75000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> + cpu4567_crit: trip1 {
> + temperature = <110000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> +
> + cooling-maps {
> + map0 {
> + trip = <&cpu4567_alert>;
> + cooling-device = <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> +
> + gpu-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens 3>;
> +
> + trips {
> + gpu_alert0: trip-point0 {
> + temperature = <75000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> + gpu_crit: gpu_crit {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + modem1-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens 0>;
> +
> + trips {
> + modem1_alert0: trip-point0 {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "hot";
> + };
> + };
> + };
> +
> + modem2-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens 2>;
> +
> + trips {
> + modem2_alert0: trip-point0 {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "hot";
> + };
> + };
> + };
> +
> + camera-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens 1>;
> +
> + trips {
> + cam_alert0: trip-point0 {
> + temperature = <75000>;
> + hysteresis = <2000>;
> + type = "hot";
> + };
> + };
> + };
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
> + };
> +
> + vreg_dummy: regulator-dummy {
This deserves at least a comment.. is it necessary to satisfy
cpufreq-dt or something?
Konrad
> + #power-domain-cells = <0>;
> + };
> +
> + wcnss-smp2p {
> + compatible = "qcom,smp2p";
> + qcom,smem = <451>, <431>;
> +
> + interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
> +
> + mboxes = <&apcs1_mbox 18>;
> +
> + qcom,local-pid = <0>;
> + qcom,remote-pid = <4>;
> +
> + wcnss_smp2p_out: master-kernel {
> + qcom,entry-name = "master-kernel";
> +
> + #qcom,smem-state-cells = <1>;
> + };
> +
> + wcnss_smp2p_in: slave-kernel {
> + qcom,entry-name = "slave-kernel";
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +};
Powered by blists - more mailing lists