[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <CAHCN7xJQZgLgDH_beWZfvzksEgm87rotfq7T2SMhgzjojJesKg@mail.gmail.com>
Date: Fri, 6 Jan 2023 08:32:25 -0600
From: Adam Ford <aford173@...il.com>
To: Geert Uytterhoeven <geert@...ux-m68k.org>
Cc: linux-renesas-soc@...r.kernel.org, aford@...conembedded.com,
Magnus Damm <magnus.damm@...il.com>,
Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
Andrew Lunn <andrew@...n.ch>,
Heiner Kallweit <hkallweit1@...il.com>,
Russell King <linux@...linux.org.uk>,
netdev <netdev@...r.kernel.org>
Subject: Re: [PATCH 2/4] Revert "arm64: dts: renesas: Add compatible
properties to AR8031 Ethernet PHYs"
On Fri, Jan 6, 2023 at 8:28 AM Geert Uytterhoeven <geert@...ux-m68k.org> wrote:
>
> Hi Adam,
>
> CC Ethernet phy
>
> On Wed, Jan 4, 2023 at 3:12 PM Adam Ford <aford173@...il.com> wrote:
> > This reverts commit 18a2427146bf8a3da8fc7825051d6aadb9c2d8fb.
> >
> > Due to the part shortage, the AR8031 PHY was replaced with a
> > Micrel KSZ9131. Hard-coding the ID of the PHY makes this new
> > PHY non-operational. Since previous hardware had shipped,
> > it's not as simple as just replacing the ID number as it would
> > break the older hardware. Since the generic mode can correctly
> > identify both versions of hardware, it seems safer to revert
> > this patch.
> >
> > Signed-off-by: Adam Ford <aford173@...il.com>
>
> Thanks for your patch!
>
> > --- a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi
> > +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi
> > @@ -59,8 +59,6 @@ &avb {
> > status = "okay";
> >
> > phy0: ethernet-phy@0 {
> > - compatible = "ethernet-phy-id004d.d074",
> > - "ethernet-phy-ieee802.3-c22";
> > reg = <0>;
> > interrupt-parent = <&gpio2>;
> > interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
>
> The next line:
>
> reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
>
> Unfortunately, removing the compatible value will cause regressions
> for kexec/kdump and for Ethernet driver unbind, as the PHY reset will
> be asserted before starting the new kernel, or on driver unbind.
> Due to a deficiency in the Ethernet PHY subsystem, the PHY will be
> probed while the reset is still asserted, and thus fail probing[1].
FWIW, the bootloader brings the device out of reset. Would it be
sufficient to keep "ethernet-phy-ieee802.3-c22" and drop the
hard-coded ID?
thanks,
adam
>
> Is there a (new) proper way to handle this?
> Perhaps the issue has been fixed in the PHY subsystem meanwhile?
>
> Thanks!
>
> [1] https://lore.kernel.org/all/cover.1631174218.git.geert+renesas@glider.be
>
> Gr{oetje,eeting}s,
>
> Geert
>
> --
> Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@...ux-m68k.org
>
> In personal conversations with technical people, I call myself a hacker. But
> when I'm talking to journalists I just say "programmer" or something like that.
> -- Linus Torvalds
Powered by blists - more mailing lists