Message-ID: <6dfca582-3ec5-f652-4285-b2a1b34b5981@linaro.org>
Date:   Thu, 12 Jan 2023 17:29:39 +0100
From:   Konrad Dybcio <konrad.dybcio@...aro.org>
To:     Nikita Travkin <nikita@...n.ru>
Cc:     Yang Xiwen <forbidden405@...mail.com>,
        Andy Gross <agross@...nel.org>,
        Bjorn Andersson <andersson@...nel.org>,
        Rob Herring <robh+dt@...nel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
        linux-arm-msm@...r.kernel.org, devicetree@...r.kernel.org,
        linux-kernel@...r.kernel.org,
        Jaime Breva <jbreva@...arsystems.com>,
        ~postmarketos/upstreaming@...ts.sr.ht
Subject: Re: [PATCH v2 3/3] arm64: dts: qcom: msm8916-thwc: Add initial device
 tree for Tong Heng Wei Chuang Wifi/LTE dongle UFI-001C and uf896



On 12.01.2023 17:28, Nikita Travkin wrote:
> Konrad Dybcio писал(а) 12.01.2023 21:16:
>> On 11.01.2023 15:13, Yang Xiwen wrote:
>>> This commit adds support for the ufi-001C and uf896 WiFi/LTE dongle made by
>>> Tong Heng Wei Chuang based on MSM8916.
>>> uf896 is another variant for the usb stick. The board design
>>> differs by using different gpios for the keys and leds.
>>>
>>> Note: The original firmware does not support 64-bit OS. It is necessary
>>> to flash 64-bit TZ firmware to boot arm64.
>>>
>>> Currently supported:
>>> - All CPU cores
>>> - Buttons
>>> - LEDs
>>> - Modem
>>> - SDHC
>>> - USB Device Mode
>>> - UART
>>>
>>> Co-developed-by: Jaime Breva <jbreva@...arsystems.com>
>>> Signed-off-by: Jaime Breva <jbreva@...arsystems.com>
>>> Co-developed-by: Nikita Travkin <nikita@...n.ru>
>>> Signed-off-by: Nikita Travkin <nikita@...n.ru>
>>> Signed-off-by: Yang Xiwen <forbidden405@...mail.com>
>>> ---
>>>  arch/arm64/boot/dts/qcom/Makefile             |   2 +
>>>  .../boot/dts/qcom/msm8916-thwc-uf896.dts      |  41 +++
>>>  .../boot/dts/qcom/msm8916-thwc-ufi001c.dts    |  39 +++
>>>  arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi     | 246 ++++++++++++++++++
>>>  4 files changed, 328 insertions(+)
>>>  create mode 100644 arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts
>>>  create mode 100644 arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts
>>>  create mode 100644 arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi
>>>
>>> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
>>> index b42362c7be1bf..523dbe6d06be8 100644
>>> --- a/arch/arm64/boot/dts/qcom/Makefile
>>> +++ b/arch/arm64/boot/dts/qcom/Makefile
>>> @@ -21,6 +21,8 @@ dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-e7.dtb
>>>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-grandmax.dtb
>>>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-j5.dtb
>>>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-serranove.dtb
>>> +dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-thwc-uf896.dtb
>>> +dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-thwc-ufi001c.dtb
>>>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt88047.dtb
>>>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8953-motorola-potter.dtb
>>>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8953-xiaomi-daisy.dtb
>>> diff --git a/arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts b/arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts
>>> new file mode 100644
>>> index 0000000000000..79447ca48dd3a
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts
>>> @@ -0,0 +1,41 @@
>>> +// SPDX-License-Identifier: GPL-2.0-only
>>> +
>>> +/dts-v1/;
>>> +
>>> +#include "msm8916-ufi.dtsi"
>>> +
>>> +/ {
>>> +	model = "uf896 4G Modem Stick";
>>> +	compatible = "thwc,uf896", "qcom,msm8916";
>>> +};
>>> +
>>> +&button_restart {
>>> +	gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
>>> +};
>>> +
>>> +&led_r {
>>> +	gpios = <&msmgpio 82 GPIO_ACTIVE_HIGH>;
>>> +};
>>> +
>>> +&led_g {
>>> +	gpios = <&msmgpio 83 GPIO_ACTIVE_HIGH>;
>>> +	function = LED_FUNCTION_WLAN;
>> This is a software property, maybe it would be worth
>> commonizing?
>>
> 
> The functions are put in-line with the labels on the housing.
> The uf896 has green and blue leds labeled with icons but I was told
> by Yang that the uf001c doesn't have any labels.
Okay, that probably deserves a comment.

> 
>>> +};
>>> +
>>> +&led_b {
>>> +	gpios = <&msmgpio 81 GPIO_ACTIVE_HIGH>;
>>> +	function = LED_FUNCTION_WAN;
>>> +};
>>> +
>>> +&button_default {
>>> +	pins = "gpio35";
>>> +	bias-pull-up;
>>> +};
>>> +
>>> +&gpio_leds_default {
>>> +	pins = "gpio81", "gpio82", "gpio83";
>>> +};
>>> +
>>> +&sim_ctrl_default {
>>> +	pins = "gpio1", "gpio2";
>>> +};
>>> diff --git a/arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts b/arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts
>>> new file mode 100644
>>> index 0000000000000..700cf81cbf8c0
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts
>>> @@ -0,0 +1,39 @@
>>> +// SPDX-License-Identifier: GPL-2.0-only
>>> +
>>> +/dts-v1/;
>>> +
>>> +#include "msm8916-ufi.dtsi"
>>> +
>>> +/ {
>>> +	model = "ufi-001c/ufi-001b 4G Modem Stick";
>>> +	compatible = "thwc,ufi001c", "qcom,msm8916";
>>> +};
>>> +
>>> +&button_restart {
>>> +	gpios = <&msmgpio 37 GPIO_ACTIVE_HIGH>;
>>> +};
>>> +
>>> +&led_r {
>>> +	gpios = <&msmgpio 22 GPIO_ACTIVE_HIGH>;
>>> +};
>>> +
>>> +&led_g {
>>> +	gpios = <&msmgpio 21 GPIO_ACTIVE_HIGH>;
>>> +};
>>> +
>>> +&led_b {
>>> +	gpios = <&msmgpio 20 GPIO_ACTIVE_HIGH>;
>>> +};
>>> +
>>> +&button_default {
>>> +	pins = "gpio37";
>>> +	bias-pull-down;
>>> +};
>>> +
>>> +&gpio_leds_default {
>>> +	pins = "gpio20", "gpio21", "gpio22";
>>> +};
>>> +
>>> +&sim_ctrl_default {
>>> +	pins = "gpio1", "gpio2";
>> Identical between both boards, move to common please.
>>
>>> +};
>>> diff --git a/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi b/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi
>>> new file mode 100644
>>> index 0000000000000..286768d0fbe70
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi
>>> @@ -0,0 +1,246 @@
>>> +// SPDX-License-Identifier: GPL-2.0-only
>>> +
>>> +#include "msm8916-pm8916.dtsi"
>>> +
>>> +#include <dt-bindings/gpio/gpio.h>
>>> +#include <dt-bindings/leds/common.h>
>>> +
>>> +/ {
>>> +	chassis-type = "embedded";
>>> +
>>> +	aliases {
>>> +		serial0 = &blsp1_uart2;
>>> +	};
>>> +
>>> +	chosen {
>>> +		stdout-path = "serial0";
>>> +	};
>>> +
>>> +	reserved-memory {
>>> +		mpss_mem: mpss@...00000 {
>>> +			reg = <0x0 0x86800000 0x0 0x5500000>;
>>> +			no-map;
>>> +		};
>>> +
>>> +		gps_mem: gps@...00000 {
>>> +			reg = <0x0 0x8bd00000 0x0 0x200000>;
>>> +			no-map;
>>> +		};
>>> +	};
>>> +
>>> +	gpio-keys {
>>> +		compatible = "gpio-keys";
>>> +
>>> +		pinctrl-0 = <&button_default>;
>>> +		pinctrl-names = "default";
>>> +
>>> +		label = "GPIO Buttons";
>>> +
>>> +		/* gpio is board-specific */
>> GPIO is an acronym, please make it uppercase, as you
>> did 10 lines below..
>>
>>> +		button_restart: button-restart {
>>> +			label = "Restart";
>>> +			linux,code = <KEY_RESTART>;
>>> +		};
>>> +	};
>>> +
>>> +	leds {
>>> +		compatible = "gpio-leds";
>>> +
>>> +		pinctrl-0 = <&gpio_leds_default>;
>>> +		pinctrl-names = "default";
>>> +
>>> +		/* GPIOs are board-specific */
>>> +		led_r: led-r {
>>> +			color = <LED_COLOR_ID_RED>;
>>> +			default-state = "on";
>>> +			function = LED_FUNCTION_INDICATOR;
>>> +		};
>>> +
>>> +		led_g: led-g {
>>> +			color = <LED_COLOR_ID_GREEN>;
>>> +			default-state = "off";
>>> +			function = LED_FUNCTION_INDICATOR;
>>> +		};
>>> +
>>> +		led_b: led-b {
>>> +			color = <LED_COLOR_ID_BLUE>;
>>> +			default-state = "off";
>>> +			function = LED_FUNCTION_INDICATOR;
>>> +		};
>>> +	};
>>> +};
>>> +
>>> +&bam_dmux {
>>> +	status = "okay";
>>> +};
>>> +
>>> +&bam_dmux_dma {
>>> +	status = "okay";
>>> +};
>>> +
>>> +&blsp1_uart2 {
>>> +	status = "okay";
>>> +};
>>> +
>>> +/* Remove &dsi_phy0 from clocks to make sure that gcc probes with display disabled */
>> That sounds like a bad regression and shouldn't be an issue..
>>
>>> +&gcc {
>>> +	clocks = <&xo_board>, <&sleep_clk>, <0>, <0>, <0>, <0>, <0>;
>>> +};
>>> +
>>> +&mpss {
>>> +	pinctrl-0 = <&sim_ctrl_default>;
>>> +	pinctrl-names = "default";
>>> +
>>> +	status = "okay";
>>> +};
>>> +
>>> +&pm8916_usbin {
>>> +	status = "okay";
>>> +};
>>> +
>>> +&pronto {
>>> +	status = "okay";
>>> +};
>>> +
>>> +&sdhc_1 {
>>> +	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
>>> +	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
>>> +	pinctrl-names = "default", "sleep";
>>> +
>>> +	status = "okay";
>>> +};
>>> +
>>> +&usb {
>>> +	extcon = <&pm8916_usbin>;
>>> +	dr_mode = "peripheral";
>>> +
>>> +	status = "okay";
>>> +};
>>> +
>>> +&usb_hs_phy {
>>> +	extcon = <&pm8916_usbin>;
>>> +};
>>> +
>>> +&smd_rpm_regulators {
>> Please sort this reference alphabetically.
>>
> 
> The regulators and tlmm nodes are deliberately put last,
> in line with all other msm8916 devices. We move them away
> so they don't clutter more interesting nodes with these "dry"
> and somewhat uninteresting voltage/pin definitions.
> 
> Thanks for the review,
> Nikita
Ugh, I don't know anymore.. wild west..

Konrad
> 
>> Konrad
>>> +	vdd_l1_l2_l3-supply = <&pm8916_s3>;
>>> +	vdd_l4_l5_l6-supply = <&pm8916_s4>;
>>> +	vdd_l7-supply = <&pm8916_s4>;
>>> +
>>> +	s3 {
>>> +		regulator-min-microvolt = <1200000>;
>>> +		regulator-max-microvolt = <1300000>;
>>> +	};
>>> +
>>> +	s4 {
>>> +		regulator-min-microvolt = <1800000>;
>>> +		regulator-max-microvolt = <2100000>;
>>> +	};
>>> +
>>> +	l1 {
>>> +		regulator-min-microvolt = <1225000>;
>>> +		regulator-max-microvolt = <1225000>;
>>> +	};
>>> +
>>> +	l2 {
>>> +		regulator-min-microvolt = <1200000>;
>>> +		regulator-max-microvolt = <1200000>;
>>> +	};
>>> +
>>> +	l4 {
>>> +		regulator-min-microvolt = <2050000>;
>>> +		regulator-max-microvolt = <2050000>;
>>> +	};
>>> +
>>> +	l5 {
>>> +		regulator-min-microvolt = <1800000>;
>>> +		regulator-max-microvolt = <1800000>;
>>> +	};
>>> +
>>> +	l6 {
>>> +		regulator-min-microvolt = <1800000>;
>>> +		regulator-max-microvolt = <1800000>;
>>> +	};
>>> +
>>> +	l7 {
>>> +		regulator-min-microvolt = <1800000>;
>>> +		regulator-max-microvolt = <1800000>;
>>> +	};
>>> +
>>> +	l8 {
>>> +		regulator-min-microvolt = <2850000>;
>>> +		regulator-max-microvolt = <2900000>;
>>> +	};
>>> +
>>> +	l9 {
>>> +		regulator-min-microvolt = <3300000>;
>>> +		regulator-max-microvolt = <3300000>;
>>> +	};
>>> +
>>> +	l10 {
>>> +		regulator-min-microvolt = <2700000>;
>>> +		regulator-max-microvolt = <2800000>;
>>> +	};
>>> +
>>> +	l11 {
>>> +		regulator-min-microvolt = <1800000>;
>>> +		regulator-max-microvolt = <2950000>;
>>> +		regulator-system-load = <200000>;
>>> +		regulator-allow-set-load;
>>> +	};
>>> +
>>> +	l12 {
>>> +		regulator-min-microvolt = <1800000>;
>>> +		regulator-max-microvolt = <2950000>;
>>> +	};
>>> +
>>> +	l13 {
>>> +		regulator-min-microvolt = <3075000>;
>>> +		regulator-max-microvolt = <3075000>;
>>> +	};
>>> +
>>> +	l14 {
>>> +		regulator-min-microvolt = <1800000>;
>>> +		regulator-max-microvolt = <3300000>;
>>> +	};
>>> +
>>> +	l15 {
>>> +		regulator-min-microvolt = <1800000>;
>>> +		regulator-max-microvolt = <3300000>;
>>> +	};
>>> +
>>> +	l16 {
>>> +		regulator-min-microvolt = <1800000>;
>>> +		regulator-max-microvolt = <3300000>;
>>> +	};
>>> +
>>> +	l17 {
>>> +		regulator-min-microvolt = <2850000>;
>>> +		regulator-max-microvolt = <2850000>;
>>> +	};
>>> +
>>> +	l18 {
>>> +		regulator-min-microvolt = <2700000>;
>>> +		regulator-max-microvolt = <2700000>;
>>> +	};
>>> +};
>>> +
>>> +&msmgpio {
>>> +	/* pins are board-specific */
>>> +	button_default: button-default-state {
>>> +		function = "gpio";
>>> +		drive-strength = <2>;
>>> +	};
>>> +
>>> +	gpio_leds_default: gpio-leds-default-state {
>>> +		function = "gpio";
>>> +		drive-strength = <2>;
>>> +		bias-disable;
>>> +	};
>>> +
>>> +	sim_ctrl_default: sim-ctrl-default-state {
>>> +		function = "gpio";
>>> +		drive-strength = <2>;
>>> +		bias-disable;
>>> +		output-low;
>>> +	};
>>> +};

Powered by blists - more mailing lists