| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20230118210319.464371-4-martin.botka@somainline.org>
Date: Wed, 18 Jan 2023 22:03:18 +0100
From: Martin Botka <martin.botka@...ainline.org>
To: Martin Botka <martin.botka@...ainline.org>,
Andre Przywara <andre.przywara@....com>
Cc: Konrad Dybcio <konrad.dybcio@...ainline.org>,
AngeloGioacchino Del Regno
<angelogioacchino.delregno@...ainline.org>,
Marijn Suijten <marijn.suijten@...ainline.org>,
Jami Kettunen <jamipkettunen@...ainline.org>,
Paul Bouchara <paul.bouchara@...ainline.org>,
Jan Trmal <jtrmal@...il.com>,
Jernej Skrabec <jernej.skrabec@...il.com>,
Samuel Holland <samuel@...lland.org>,
Martin Botka <martin.botka1@...il.org>,
Lee Jones <lee@...nel.org>, Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Chen-Yu Tsai <wens@...e.org>,
Liam Girdwood <lgirdwood@...il.com>,
Mark Brown <broonie@...nel.org>, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org
Subject: [PATCH v7 3/3] regulator: axp20x: Add support for AXP313a variant
The AXP313a is your typical I2C controlled PMIC, although in a lighter
fashion compared to the other X-Powers PMICs: it has only three DCDC
rails, three LDOs, and no battery charging support.
The AXP313a datasheet does not describe a register to change the DCDC
switching frequency, and talks of it being fixed at 3 MHz. The BSP
driver hints at a register being able to change that, but we haven't
verified that, so leave that one out. It can be added later, if needed
and/or required.
The third LDO, RTCLDO, is fixed, and cannot even be turned on or off,
programmatically. On top of that, its voltage is customisable (either
1.8V or 3.3V), which we cannot describe easily using the existing
regulator wrapper functions. This should be fixed properly, using
regulator-{min,max}-microvolt in the DT, but this requires more changes
to the code. As some other PMICs (AXP2xx, AXP803) seem to paper over the
same problem as well, we follow suit here and pretend it's a fixed 1.8V
regulator. A proper fix can follow later. The BSP code seems to ignore
this regulator altogether.
Describe the AXP313A's voltage settings and switch registers, how the
voltages are encoded, and connect this to the MFD device via its
regulator ID.
Signed-off-by: Martin Botka <martin.botka@...ainline.org>
Signed-off-by: Andre Przywara <andre.przywara@....com>
---
drivers/regulator/axp20x-regulator.c | 60 ++++++++++++++++++++++++++++
1 file changed, 60 insertions(+)
diff --git a/drivers/regulator/axp20x-regulator.c b/drivers/regulator/axp20x-regulator.c
index d260c442b788..3087bc98694f 100644
--- a/drivers/regulator/axp20x-regulator.c
+++ b/drivers/regulator/axp20x-regulator.c
@@ -134,6 +134,11 @@
#define AXP22X_PWR_OUT_DLDO4_MASK BIT_MASK(6)
#define AXP22X_PWR_OUT_ALDO3_MASK BIT_MASK(7)
+#define AXP313A_DCDC1_NUM_VOLTAGES 107
+#define AXP313A_DCDC23_NUM_VOLTAGES 88
+#define AXP313A_DCDC_V_OUT_MASK GENMASK(6, 0)
+#define AXP313A_LDO_V_OUT_MASK GENMASK(4, 0)
+
#define AXP803_PWR_OUT_DCDC1_MASK BIT_MASK(0)
#define AXP803_PWR_OUT_DCDC2_MASK BIT_MASK(1)
#define AXP803_PWR_OUT_DCDC3_MASK BIT_MASK(2)
@@ -638,6 +643,48 @@ static const struct regulator_desc axp22x_drivevbus_regulator = {
.ops = &axp20x_ops_sw,
};
+static const struct linear_range axp313a_dcdc1_ranges[] = {
+ REGULATOR_LINEAR_RANGE(500000, 0, 70, 10000),
+ REGULATOR_LINEAR_RANGE(1220000, 71, 87, 20000),
+ REGULATOR_LINEAR_RANGE(1600000, 88, 106, 100000),
+};
+
+static const struct linear_range axp313a_dcdc2_ranges[] = {
+ REGULATOR_LINEAR_RANGE(500000, 0, 70, 10000),
+ REGULATOR_LINEAR_RANGE(1220000, 71, 87, 20000),
+};
+
+/*
+ * This is deviating from the datasheet. The values here are taken from the
+ * BSP driver and have been confirmed by measurements.
+ */
+static const struct linear_range axp313a_dcdc3_ranges[] = {
+ REGULATOR_LINEAR_RANGE(500000, 0, 70, 10000),
+ REGULATOR_LINEAR_RANGE(1220000, 71, 102, 20000),
+};
+
+static const struct regulator_desc axp313a_regulators[] = {
+ AXP_DESC_RANGES(AXP313A, DCDC1, "dcdc1", "vin1",
+ axp313a_dcdc1_ranges, AXP313A_DCDC1_NUM_VOLTAGES,
+ AXP313A_DCDC1_CONRTOL, AXP313A_DCDC_V_OUT_MASK,
+ AXP313A_OUTPUT_CONTROL, BIT(0)),
+ AXP_DESC_RANGES(AXP313A, DCDC2, "dcdc2", "vin2",
+ axp313a_dcdc2_ranges, AXP313A_DCDC23_NUM_VOLTAGES,
+ AXP313A_DCDC2_CONRTOL, AXP313A_DCDC_V_OUT_MASK,
+ AXP313A_OUTPUT_CONTROL, BIT(1)),
+ AXP_DESC_RANGES(AXP313A, DCDC3, "dcdc3", "vin3",
+ axp313a_dcdc3_ranges, AXP313A_DCDC23_NUM_VOLTAGES,
+ AXP313A_DCDC3_CONRTOL, AXP313A_DCDC_V_OUT_MASK,
+ AXP313A_OUTPUT_CONTROL, BIT(2)),
+ AXP_DESC(AXP313A, LDO1, "ldo1", "vin1", 500, 3500, 100,
+ AXP313A_ALDO1_CONRTOL, AXP313A_LDO_V_OUT_MASK,
+ AXP313A_OUTPUT_CONTROL, BIT(3)),
+ AXP_DESC(AXP313A, LDO2, "ldo2", "vin1", 500, 3500, 100,
+ AXP313A_DLDO1_CONRTOL, AXP313A_LDO_V_OUT_MASK,
+ AXP313A_OUTPUT_CONTROL, BIT(4)),
+ AXP_DESC_FIXED(AXP313A, RTC_LDO, "rtc-ldo", "vin1", 1800),
+};
+
/* DCDC ranges shared with AXP813 */
static const struct linear_range axp803_dcdc234_ranges[] = {
REGULATOR_LINEAR_RANGE(500000,
@@ -1040,6 +1087,15 @@ static int axp20x_set_dcdc_freq(struct platform_device *pdev, u32 dcdcfreq)
def = 3000;
step = 150;
break;
+ case AXP313A_ID:
+ /* The DCDC PWM frequency seems to be fixed to 3 MHz. */
+ if (dcdcfreq != 3000000) {
+ dev_err(&pdev->dev,
+ "DCDC frequency on AXP313a is fixed to 3 MHz.\n");
+ return -EINVAL;
+ }
+
+ return 0;
default:
dev_err(&pdev->dev,
"Setting DCDC frequency for unsupported AXP variant\n");
@@ -1232,6 +1288,10 @@ static int axp20x_regulator_probe(struct platform_device *pdev)
drivevbus = of_property_read_bool(pdev->dev.parent->of_node,
"x-powers,drive-vbus-en");
break;
+ case AXP313A_ID:
+ regulators = axp313a_regulators;
+ nregulators = AXP313A_REG_ID_MAX;
+ break;
case AXP803_ID:
regulators = axp803_regulators;
nregulators = AXP803_REG_ID_MAX;
--
2.39.0
Powered by blists - more mailing lists